man engine used for sale

Scrap shear dentition attachment for an excavator unused MBI ZHEJIANG MANTOVANI MANTOVANIBENNE Type MS15-MC Year: 2020 Overall dimensions: 1100 x 1000 x 500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved

5-Axis Horizontal Machining Center with Pallet changer Mandelli Spark 3500X New in 2018 Siemens Sinumerik 840D control Number of pallets 2 Pallet size 1250 x 1600 mm Pallet load capacity max. 5100 kg 4th axis 0.001° NC rotary table 5th Axis NC-Tilting milling head A-Axis +80° ~ -120° X 3500mm Y 1850mm Z 1800 mm Feeds X,Y,Z up to 20000 mm/min. Rapids X,Y,Z up to 35000 mm/min. Tool taper HSK-A100 Spindle drive motor rating 46/67.7 kW Spindle speeds up to 6000 rpm. Spindle torque max. 1851 Nm 200 station tool magazines. Tool diameter max. 120 mm/425 mm Tool length max. 600 mm Tool weight max. 35 kg Coolant through the spindle 25/40/60 bar Proposal Number MH-6234

Tank scissor dentition, scrap scissor bit attachment for an excavator used MBI ZHEJIANG MANTOVANI MANTOVANIBENNE for MS22 Overall dimensions: 1400 x 1300 x 500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved

Available in stock 1 x Used MAN NR34/S022 Turbocharger. Fully serviced at MAN and ready to be installed. The equipment is used but in good working conditions.

Key data: 18 , 8 , 3

Screw compressor Mannesmann DEMAG SE 30 S 3 m³/min, 8 bar, 18.5 kW Good condition Test run carried out Ready for action

High-quality lattice supports with high load capacities, inexpensive alternative for gratings – Brand new – Prices on request! Manufacturer: Delta Shelving Type: Manta Mesh Standard width: 885mm (with a 2.70m trusss then 3 supports are needed = 2.655mm) 1335mm Frame depths: 1.05m 1,10 1.20m Other depths on request! Evenly distributed load: between 250 and 1,500kg Standard (price applies to the standard version): 1.000kg, i.e. also per pallet Lattice grid: 50 x 100 or 25x100mm Please also indicate which beam type (truss type) you have! So whether box profile (or IPE carrier) 50 or 40mm, or whether they have trusses with step. Advantages: no sharp edges 200% safety factor – independent of the shelf beams Bealstable for permissible deflection and structural failure Large selection of standard sizes and load capacities MantaMESH is our market-leading wire me ...

Manesty D3B tablet press Serial: 24D117 Manesty 16 station tablet press, up to 500 tablets per min, max tablet diameter 25mm, max depth to fill 20mm, 3Ph

Manesty D3B tablet press Manesty 16 station tablet press, up to 500 tablets per min, max tablet diameter 25mm, max depth to fill 20mm, 3Ph

Perfector 1/5 and 6/0, RCI CCI Comand Table, SAPC Semi Autoplate Change, Rolandmatic Dampening with Technotrans Refrigerator, Auto-Wash, Double Size Impression Cylinders, Roland Mabeg Jet Feeder, Steel Plate on Overlap, High Pile Delivery, Autosize, IR Dryer and UV Dryer, Standard Accessories

saw blade diameter: 370 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 100 mm : 180x100 mm Working height: 925 mm saw blade turning speeds: 15 - 70 U/min total power requirement: 1,8/2,2 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 0,8 x 1,0 x 1,85 m SPECIAL PRICE! High-performance vertical circular saw VKS 370 (20177/201178) · miter left 60° + right 45° · Vice with double clamping arm · Robust prism guide of the saw head, adjustable dovetail guide. · Chip brush · Automatic cooling · Metal handle for high clamping force · Solid, strong cast iron table · Spring pack · Chip removal brush ATTENTION: Price is without saw blade! (saw blade price EUR 204) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SUB: FOR SALE... MAN 8L 20 / 27. USED CRANKSHAFTS AT TURKEY HAVE A GDY SIR WE VE 2 PCS USED MAN 8L 20 / 27 CRANKSHAFTS AT OUR STOCK AT TURKEY.. CRANSHAFTS MEASURMENTS IN STANDART SIZE LIMITIS CRANKSHAFT CLASS STAMP ON ATTACHED PICTURE. CRANKSHAFTS ARE READY TO INSPECTION AT WORK SHOP IF YOU HAVE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurlubay Regards; Aliaga marine services E-mail: infoaliagamarine.com PHN/fax: + 90 232 618 03 88 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

Manz Automation aico.panel 80036808 Touch-Panel 19" aico.box.IPC V2 81009594 Set Item Condition: New as pictured Possible traces of storage, installed but not put into operation. Type: aico.panel Art-No.: 80036808 24VDC/2A Type: aico.box.IPC V2 Art-No.:81009594 REV: 2.1; 100-240 VAC / 4-2A; 50/60Hz Incl. accessories 30kg More items - new and used - can be found in our shop! International shipping costs on request!

58 Mw MAN 18V48/60TS power plant 50 Hz 3 x Man 18V48/60TS generators together with auxilary equipments Approx 4000 Working hours each 58 Megawatts total power 19305kw each at 500 RPM and 50 Hz Engines year of build 2014 with ABB AMG1600UU12 DSE Alternators Alternators year of build 2015

1. VFK CARTRIDGE FILTERED POWDER COATING BOOTH (1-SIDED) Cartridge type powder coating booths are cost-effective solutions for companies that generally use single color powder coating or do not change the paint color much. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists of pulse valves and a compressed air tank, controlled automatically or operated using manual buttons on the control panel. POWDER RECYCLING As a result of the filter cleaning system, powder coating particles fall down and are manually collected in a bucket at the bot ...

Key data: 630 mm

Manual Tin Shears / Guillotine Shears with Table - Heavy-duty design - Adjustable front stop 360 mm - with table and runway Specification - Max. cutting length: 630 mm - Table dimensions WxD: 630 x 540 mm - Front stop: 360 mm - Dimensions WxHxD: approx. 1000 x 1200 x 2000 mm - Weight: approx. 300 kg

ID2953 Henke Variant year of construction 1992/93 Brick Manufacturing Plant with core and attachment, for the production of paving stones, slabs, kerbstones, U and L stones, hollow blocks Board size 1,350 x 1,150mm (approx. 1935 piece) Min. product height 40 mm Max. product height 500 mm Drawing plate function and cross-punch cleaning Vibration HENKE Vibra-Matik with 4 servomotors SEW Renewal of the machine control in 2011 to Siemens S7-400 incl. Board destacking device wet side incl. Conveyor line wet side (V-belt and intermediate chain transport) incl. Conveyor section on the dry side (latch track and lowering ladder outlet) incl. Board turning cross dry side incl. Board stacking device dry side incl. Board package lift truck with transverse traversing platform (board storage) incl. Packaging HENKE incl. drying chamber The machine is in good working condition and can ...

ID2954 Niemeyer manhole finisher year/Year of construction 1996 Manhole finisher, with conveyor belt, vibrator, outlets, wall traverse, filling carriage, manhole inserts (worth approx. 23,500 euros), accessories Shaft ring paver, with feed belt, vibrator, outlets, wall traverse, filling trolley, shaft inserts (worth approx. 23,500 euros), accessories

amount: 1 STK height: 450 mm external diameter: 340 mm Filter cartridge/3-5µm 340 x 450 mm - H 34 2240/40 KIT MANN FILTER Oil filter element Mann filter element for oil of the highest quality for wire erosion, die sinking and spark erosion drilling. The Mann + Hummel H 34 2240/40 KIT oil filter element reliably removes dirt and solid particles such as dust, metal abrasion, oil, carbon, soot, etc. It offers protection and is used for the filtration of engine, hydraulic and gear oil. Technical data Height: 450 mm Outer diameter: 340 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 70

MAN E0836 E302 CHP Unit in Acoustic Canopy for Sale. Capacity: 70kW Hours: 4,500 Year: 2011 Fuel: Natural gas Voltage: 400 Hz: 50 Scope of supply: Engine, Alternator, Control Panel, Acoustic canopy, Canopy fan, Engine water pump. Footprint of the combined heat and power unit is 3.4 meters x 1.14 meters including the control panel. It has been serviced every 1000 hours. The unit is not due an overhaul until 24,000 hours. Engine has been barred over, and the canopy fan and engine water pump have been powered up. The unit is in a warm boiler room so is in good condition. Available for sale from Gas Engine Exchange . Please check our complete range of equipment at gasengineexchange.com.

Man 12 Cylinder container for sale. Price: Please Apply Available for sale from Gas Engine Exchange . Please check our complete range of equipment at gasengineexchange.com.

Weight: 0.1 tons Power: 0.6 Kw Waterpressure: 3 Bar Length mm: 1600 Width mm: 900 Height mm: 1300 Working height: 90 cm Transport size L x W x H: 2,5 x 1,36 x 1,3 Min.-max glass size: 1,20 x 55 cm Number of spindles: 1 Condition machine : Good Control type: Manual Electric. Connection: 16A 400V Documentation: No Instructions: No Electric diagram: No Parts list: N/a Available software: N/a Photos/film available: Photos and video available

Key data: 220

MAN Lean Burn Biogas 2876 LE302 Containerised Generator. Model: MAN Lean Burn Biogas 2876 LE302 Capacity: 220 kW Hours: 0 Year: 2016 Fuel: Biogas V: 400 HZ: 50 Scope of supply : New MAN 2876 LE302 and ComAp Control Panel. Used Container, Alternator, Radiators and Gas line. MAN Engine comes with manufacturers warranty. Available for sale from Gas Engine Exchange. Please check our complete range of equipment at gasengineexchange.com.

MAN 6L23/30 Crankshaft in good condition STD size, Measurment Control, Hardness Control, Crack Test, Oscillation tests done From our istanbul stock contact us at: infofin-marine for more information

MAN 27/38 Cylinder heads Std sized seat bores Free of cracks and weldings 20 pcs available in good condition From our istanbul stock Please contact us at infofin-marine

MAN 28/32H spares available: MAN 28/32H 15 pcs cylinder heads with std sized exh seat bores free of cracks and weldings MAN 28/32H pistons 10 pcs std sized ring grooves free of cracks and weldings MAN 28/32H connecting rods 5 pcs free of ovality and cracks MAN 28/32H water jackets 8 pcs From our istanbul stock Please contact us at infofin-marine

MAN 32/40 Cylinder heads Augsburg type 11 pcs available froms stock in good condition std sized seat bores, free of cracks and weldings from our istanbul stock

volume capacity: 5,63 m³/min suction: 1 bar pressure: 8 bar turning speeds: 3000 U/min engine output: 37 kW dimensions of machine L x W x H: 1,35 x 1,05 x 1,43 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

MAN 7L32/40 Crankshaft Std sized Free of cracks , weldings or oscillation Reports available

Exhaust gas compensator MAN D2842

MAN Gas Generator in Box Manufacturer : MAN Rated Output Power : 350 KVA Speed :1500 RPM Voltage : 400 V Frequency : 50 Hz Condition : Used Fuel : Gas Cylinder : 12 Cylinder Please see attached the pictures for the units available for sale. Kindly advise your interest if you would like to get further details feel free to contact us back. For arranging the visit inspection; and pricing information feel free to contact us at: Enquiries@ukpowergeneratorsltd 00447956518924

SPECIFICATIONS: Dimensions of the work table mm: 2500 x 1300 Number of pistons: 4 Diameter Ø 90 mm Piston stroke mm: 470 Complete with intermediate plate Operation with water

Bosch Injection Pump for MAN D2842 LE211 with GAC controller, cf. MAN part number: 51.11103-7451 59.11103-7451 N (l/min): 750 RW (mm): 12.7 or 13.6 EPP-FM (mm³/H): 332 or 367

Key data: 400 KW, 570 kVA, 400 V

Dear Ladies and Gentlemen, We hereby offer the following a MAN CHP in a container for rent! Year of construction 2014 Starts: 757 Hours: 11448 BH. Electrical Power: 400KW Thermal power 445 KW Dimensioning: Thickness: 100/140 mm insulation Length: 10000 mm Width: 2800 mm Height: 3200 mm Paintwork: Moss Green Contents in the container: MAN gas engine with generator on substructure Central heating Heat exchanger Switchboard Gas control unit Static power supply Exhaust silencer inside Auxiliary silencer above the container Insertion loss 65dBA in 10m Data recording Gas blower Combimac blue 65mbar gas pressure Gas Flow Meter Gas vacuum monitor Return temperature increase Exhaust gas heat exchanger with bypass Gas warning system Wind Vane Guardian Flame detector 1000 l each of used and fresh oil tanks with pump and hose reel Intrigued  ...

Holder for oil filter MWM 232 for sale Mann & Hummel Part Number: 6751283106 MWM Part Number: 2404242170

Make: MAN Model: 5L21/31 Mfg date: 2012.03 Output: 1000 kW Speed: 900 RPM Generator: Hyosung Corporation Type: HMD500-08 Output: 1175 kVA Voltage: 450 V Frequency: 60 Hz Quantity: 2 Weight: 5500 kg

TO WHOM IT MAY CONCERN ; WE VE USED STANDART SIZE CRANKSHAFT OF MAN 8L 27/38 AT OUR STOCK IF YOU VE ANY FURTHER QUESTIONS . IT WAS DISMANTLED FROM GENERATOR ENGINE PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E-mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 90 Mobile: +905556084850 aliagamarine.com TURKEY

TO WHOM IT MAY CONCERN ; WE VE USED STANDART SIZE CRANKSHAFT OF MAN 6L 27/38 AT OUR STOCK IF YOU VE ANY FURTHER QUESTIONS . IT WAS DISMANTLED FROM GENERATOR ENGINE PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E-mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 90 Mobile: +905556084850 aliagamarine.com TURKEY

Key data: 550 KW, 11000 V

MAN E3262 LE202 gas generators Year of make 2015 50 Hz 550 Kw at 1500 RPM 4 units available 2 units with 0 hours and 2 units with very low working hours Auxiliary equipment also available

Key data: 254 KW

Model: MAN E2848 LE322 Hours: 14,651 Year: 2010 Fuel: Natural Gas Capacity: 254 kW Hz: 50 V: 400 Scope of supply: Engine, Alternator, Frame, Control panel, Gas Line. Available for sale from Gas Engine Exchange . Please check our complete range of equipment at gasengineexchange.com

Used machine in good condition. Available for immediate delivery. - Power source : 80 kVA - Axes: 5 - Control: SIEMENS 840D

Stockpresse / Spindle Press Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Elektro Gabelstapler / Eletric Forklift Manitou ME 315 Baujahr / Year 2017 - Serial-No. 3-Rad-Gabelstapler / 3-wheel Fork Lift Tragkraft / forklift lifting capacity max. 1500kg Lastschwerpunkt / center of gravity 500 mm Mit Ladegerät / with Charger Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Inv. Num. : 8106 Type: TP1260M Producer: Le Mans Created: 2023 Parameters: Maximum power: 6.6 kW Length of profiles: 12000 mm Maximum workpiece weight: 1000 kg Maximum profile: HEB 240 mm Maximum pipe diameter: 380 mm

Hydraulic power unit with tank, compact power unit MANNESMANN REXROTH UpA4V-10 / A4.00 - 300MA ( UpA4V-10 / A4.00-300MA ) p max = 200 bar Q = 4.0 l/min motor: 1.6 kW 220 / 380 V New ! Dimensions: 290 x 220 x 330 mm

Hydraulic power unit with radiator and tank REXROTH engine: 5.5 kW 400 V radiator Hydac OKA-R2 S/1.2/8/M engine:0.37 kW Tank: 115 l used ! Dimensions: 1100 x 1000 x 600 mm

Hydraulic pump MANNESMANN REXROTH 1PF2GU2-20/032REO07MU2 MO2 shaft Ø 32 mm Dimensions: 210 x 200 x 220 mm