mah used for sale

Compressor

Operating voltage: 400 v Ma.Nr.: 41636 HEIDENHAIN positioning and control TNC 131 / 135 Complete Dokunnetation (operating instructions, technical plans) exists. Errors excepted!

Maho UIniversaltisch

Various sub-equipment from a training workshop, to hand over individually, e.g. lid sub-device with upper beam and counter holder, Universal part apparatus with initial division Walter UTA150E with counter holder and rotary chuck 3 partial discs with parts see above, Part apparatus Walter can be swivelled without initial division. Furthermore Luenetten standing and running, on request please Specify the tip height and distance mid prism to mid plan area. Rest according to photo. Other sub-equipment susengar, Direct division Indirect division, various large sum. Please ask Sub-discs for UTA 150 E 22 24 29 36 37 49 57 63 16 30 33 36 39 51 57 63 16 27 30 33 41 47 53 61 Special price

Table clamping surface: 600 x 1100 mm traverse path x: 800 mm traverse path y: 450 mm traverse path z: 500 mm Quill stroke: by hand approximately 50 mm of spindle speeds: 63-3150 rpm stufenl feeds. adjustable: 0,1-1500 mm / min rapid traverse: x/y/z 4.5/2,6/3 m / min. Supply: 380 V, 5.5 kW space: 3000 x 2500 x 2030 mm weight: 4000 kg

Table clamping surface: 630 ø mm traverse path x: 600 mm traverse path y: 450 mm traverse path z: 500 mm Quill stroke: hand 80 mm spindle retainer: ISO 40 spindle speeds: 20-3150 rpm stufenl feeds. adjustable: 1-3000 mm / min rapid traverse rate: 4 m / min. Connection: 380V kW space: 2000 + 850 x 2000 x 2000 mm weight: 3300 kg

AMOB MAH 60/3 Section: 20 cm ³ Power: 5.5 kW - 7 hp Rpm: 11 rpm Ø instrument: 170/108 mm Ø shaft: 55/55 mm Weight: 600 kg Dimensions: 1300x890x1550 mm Nr. 3 motorized rollers hydraulic adjustment top roller Side guide rollers Programmable and displayed top roller Horizontal and vertical working position Pedal with safety device start/stop General information: The AMOB MAH series top roll profile hydraulic bending machines are the backbone of the widest selection of profile curves in the world. The MAH series is perfect for those applications that require multiple passes, where repeatability is paramount. Motorized 3-roller machines are suitable for narrower spokes and minimize material marking. Both horizontal and vertical working positions ensure that, even in the smallest workspaces, a mah series profiling machine will be placed. T ...

Control cabinet for MAHO 600 - MAHO had manual transmission damage and was therefore exploited. - Are also other parts in stock. Please inquire! Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.

Stroke x: 600 mm traverse path y: 400 mm traverse path z: 400 mm spindle retainer: ISO 40 spindle speeds: 80-4000 rpm stufenl feeds. adjustable: 0,1-1500 mm / min rapid traverse: x & y/z 4/2.5 m / min. Supply: 380 V, 16 kVA kW space: 2450 x 2200 x 1900 mm weight: 2250 kg

Control type: CNC Sinumerik 840D-SL x-way 1135 mm y-way 1050 mm z-way 750 mm table size 1400 x 1050 mm Table load 2500 kg max. workpiece size LxWxH 1400 x 1240 x 750 mm Speed 10000 rpm feed speeds X/Y/Z Axis 40000 mm/min Expressspeeds x/y/z 40000 mm/min Tool holder HSK-A100 HSK Number of places in the tool magazine 30 places max. tool weight 20 kg max. tool length 395 mm max. tool diameter 110 mm Machine height 3294 mm Drive power - spindle motor 44 kW machine weight approx. 17.9 t Space requirements approx. 15 m2 Information: Universal milling machine in mono BLOCK design (3-axis) - available September 2019 - only 3800 spindle hours, 13400 power-on hours Equipment / Accessories: - Coolant system - High-pressure pump - Chip conveyor - Hand-held panel - BALLUFF option - Documentation

-X-Way-700mm -Y-way-700mm -Z-way-700mm -Control-ITNC 530 -Spindle holder HSK A63 -Spindle speed-12000rpm -Plate changer with 7 pallets -Tool magasin with 120 -Internal cooling feeder-40bar -Spindle motor-20kW -Pallet size 500x500mm -Machine weight approx.16t -Top condition,to be visited under electricity

Various threaded rings, border raven gauges, measuring rings Etc in the item

Injection Pump Diesel Pump Stanadyne A3 DB4429-6101 JCB 320/0674 Condition: unused, there may be traces of storage Voltage: 14V Current: 95A Manufacturer: Mahle Part Number: 11 204 215 JCB Number: 320 08719 Reference: 11.204.467 , IA1484, AAK5840 , MG23, 11.204.893, AAK5881, 11.204.215, AAK5820, 11204467, 11204893, 11204215, 320/08648, 320/08649, 320/08719, 12786, 32008648, 32008649, 32008719, 705516095, 4400cc JCB 444TA1 Engine JCB Agrar Agri Tractor, 524-50, 526-56, 527-55, 531-70, 535-95-AGRI 536-60, 2CX 3CX/PLUS/CLL 4CN 4CX 225T 444, G66 QX 526-56 527-58 926 2WD/4WD 930 940 TCA74, 225 226 T 260 EcoMAX TCAE-55; T4F; 55kW, Tier 3 4 320T 325 T 330 TN 220 Agri TM 180, VM 535-95 540-140 540-200 VM115PD/HD/HPD, VM137 VTM860 527-55-WM Excavator Loader Tractor, 416HT 416S-AGRI PL1105 448 PL185 PL195 PT1120 PT18,

Table clamping area: 560 x 240 mm x-way: 300 mm y-way: 275 mm z-way: 200 mm Spindle holder: ISO 40 Spindle speeds: 40 - 2000 rpm Operating voltage: 380 V Total power requirement: 1.5 kW Space requirement: 1200 x 1100 x 1700 mm Weight: approx. 750 kg

Measuring and control ring for control of three-point internal micrometers Diameter 50mm Diameter 100mm Diameter 150mm Diameter 200mm More available

Fully functional used CNC milling machine Deckel Maho DMU 60 with rotary table Built in 1999 Heidenhain Control We would like to point out that this machine is in excellent technical and well-maintained condition for its age (due to the IATF certification). Regular maintenance is already required on the basis of the certification and the machine therefore works 100% perfectly. The machine is still energized and can be viewed and tested at any time. All maintenance logs are in place. The machine will have to leave the hall in the first quarter of 2025. This means that the machine could remain energized until mid-March 2025 to demonstrate it under power. Of course, the machine would also be available immediately. We will be happy to answer any questions you may have at any time. We are looking forward to a good cooperation and thank you for your answer and interest in adv ...

DATA ON THE MACHINE Machine type: Handwheel Manufacturer: MAHO Model: CNC Condition: ready for use (used) Price 400 â?¬ FP net plus VAT Location Warstein , Germany Reference M-MAH-1119-6 Description We offer you a used handwheel from the manufacturer MAHO Nterv suitable for e.g. MAHO MH700 Worked flawlessly up to the removal Our offer is aimed at persons who are covered within the meaning of the Trade Code in accordance with Section 14 GewO. The offer is subject to change, intermediate sale reserved. Please provide your full contact details in order to receive an offer with our Terms and Conditions of Payment. Mistakes in the descriptions and offers are reserved!

MAHO MH-700 with numeric control X, Y Table size: 800x300 Working area: X-450,Y-250,Z-300 Spindle taper: MK3 Feed range: 7-250mm/min Vertical head swiveling 90 degreess Power: 3KW Dimensions: 1300x1200x1700

Universal - Swivel - Tilting table for MAHO MH 1000 Clamping area: 1050 mm x 630 mm The Universal - Swivel - Tilting Table is in good condition

New bellows probably Maho 700 old version

Code 0739 DESCRIPTION CNC Universal toolroom milling machine Make Maho Model MH 700 C S/N 75915 Year 1984 Control Philips CNC 432 Table 900 x 500 mm Longitude ( X – axis ) table 700 mm Vertical ( Y – axis ) table 450 mm Cross ( Z – axis ) spindle 500 mm Spindle out ( H/V ) 100 mm Max. distance table / spindle horizontal 700 mm Max. distance spindle / table vertical 500 mm Spindle taper 40 ISO Speeds 20 – 3150 rpm Feeds X-Y-Z 1 – 3000 mm/min Rapides 6 m/min Spindle motor 8 kW - 380 Volts Accessories Table 900 x 500mm Condition Machine is in good condition

Filter system for low-viscosity liquids Manufacturer: Mahle Type: AF11363-1321-21000-3864/G1 All information without guarantee

Hydraulic Owner: Mahle Pressure capacity: 110 bar Flow rate: 32 L/min 160 l/min at 2 mWS 160L Tank

x-travel: 600 mm y-travel: 400 mm z-travel: 400 mm spindle taper ISO: 40 spindle turning speed range: 80 - 4000 U/min transmission ratio: 18 feed range: 0,1 - 2000 mm/min rapid traverse: x = 4 / y = 3 / z = 5 m/min table load capacity: 250 kp voltage: 380 V / 50 Hz spindle drive: 5,5 kW total power requirement: 16 kVA weight of the machine ca.: 2,6 t dimensions of the machine ca.: 3,8 x 4,3 x 2,0 m • CNC-control system 432 E • Operating hours: 37719 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1140 °C

Continious Brazing/Sintering furnace manufactured by Mahler. Type: Humpback (lower H2 consumption). Belt width: 450mm Clearance above belt: 200 mm Heating length: 5000mm Gross throughput: 600 kg/h Electric heating power: 198 kW Service temperature: 1140 Adjustable range of belt speed: 100-1000 mm/min Temperature cotroul groups: 5x Total length: 30m width: 1,8m height: 2,8m Hydrogen connection: 0,1bar 30Nm3/h (type 3.0) Nitrogen connection: 0,1 bar 60 Nm3/h (type 5.0) Exhaust gas : 300 m3/h Furnace is in use, and was regularly serviced. In 12. 2024 brick lining, heating elements, thermocouples, mesh belt and muffle was replaced . Spare parts are available, in case of interest, can be subject of seperate agreement. Offer includes: - Water cooling system with glicol base heat exchanger - Exhaust tubes (2x around 5m Stainless steel) - 5x sensor system to detect ex ...

x-travel: 630 mm y-travel: 560 mm z-travel: 560 mm Control: Heidenhain TNC 430 total power requirement: 26 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Milling machine DECKEL MAHO DMG 125

x-travel: 880 mm y-travel: 630 mm z-travel: 630 mm table surface area: 1250 x 700 mm NC-rotary table: integriert, 700 mmø spindle taper: SK 40 spindle taper: DIN 69871 spindle turning speed - stepless: 20 - 12.000 U/min control: HEIDENHAIN control: TNC 430 feeds x/y/z -stepless: 20 - 15.000 mm/min rapid traverse: 30 m/min ATC: 32 (2 x 16) Pos tool diameter: 80 / 130 mm workpiece length: 315 mm weight of tools max.: 8 kg NC-rotary table - speed -: max. 15 U/min table load: 600 / 500 kg total power requirement: 60 kW weight of the machine ca.: 9,6 t = 5-axis machining center, table clamping surface 1250 x 700 mm with integrated NC-rotary table (=4th axis), movement of milling head via control (=5th axis) Accessories: electron. handwheel, chip conveyor (snailconveyor), coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Lid Maho DMC-200 U serie 1512 5-axis CNC universal machining center, simultaneous Control: Heidenhain iTNC 530 Table size: 1600x1400 mm Table load: 3500 kg Number of pallets: 2 x Maximum workpiece diameter x height: 1950x1100 mm Travel X-axis: 1800 mm Travel Y-axis: 2000 mm Travel Z-axis: 1100 mm C-axis table rotation: 360° B-axis travel: -7/187° Spindle speed: 18000 1/min Spindle cone: HSK-A63 Spindle motor: 28/19 kW Magazine capacity: 120 Required footprint: 11200x12300 mm Height: 4375 mm Weight: 58000 kg For any questions about the machine, as well as a scheduling for the inspection, we ask you to contact us by phone or e-mail.

MAHO C Axis Machine Table - Table diameter: 600 mm Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.

CNC-Universal milling machine MAHO MH700 C Table: 900 x 500 mm Travels: -X: 700 mm -Y: 500 mm -Z: 450 mm Spindle stroke: 100 mm Spindle taper: ISO 40 Spindle speed range: 20 - 3150 rpm Total power need: 40 kva Control: Maho / Philips CNC 432 Machine weight: 3,3 tn

Machine type MIG/MAG inverter welding system Brand Mahe Type Eco MIG 300 Digital Supply voltage 3 x 400 volts Setting range 10 – 300 amperes Duty cycle 40 % ED at 300 amps 60% ED at 240 amps Current adjustment infinitely variable incl. wire automatic Cooling inverter by built-in fan Cooling burner gas-cooled Design of mobile compact system Wire feed gearbox 4-roller gearbox Fuse 16 Ampere Dimensions L x W x H 880 x 400 x 635 mm Special accessories wire switch without power for threading TIG DC, without RF Rod electrodes weldable Weight 34 kg Age as good as new Condition workshop tested, as new, incl. UVV workshop test report Scope of delivery welding system with the following accessories 1 piece welding torch 3 mtr. long 1 piece ground cable 4 mtr. long 1 piece pressure reducer argon with 2 pressure gauges 1 roll of weldin ...

Mahr 865 SE Indicator Calibrator Mahr 865 SE indicator calibrator with 1505 IC indicator + 1299 IC/S printer Height-adjustable table More indicator calibrators in other sizes - new and used - can be found in our shop! International shipping costs on request!

Machine type MIG/MAG inverter welding system Brand Mahe Type Eco MIG 300 Analog Supply voltage 3 x 400 volts Setting range 10 – 300 amperes Duty cycle 30 % ED at 300 amps 60% ED at 240 amps Current setting 12 switching stages Cooling inverter by built-in fan Cooling burner gas-cooled Design of mobile compact system Wire feeder 4-roller drive Fuse 16 Ampere Dimensions L x W x H 880 x 400 x 635 mm Special accessories wire switch without power for threading Rod electrodes weldable Weight 34 kg Age as good as new Condition workshop tested, like new, incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece welding torch 3 mtr. long 1 piece ground cable 1 piece pressure reducer argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can non-stick spray 1 piece spare parts box, k ...

Control: Siemens Travel X/Y/Z: 350 x 240 x 340 mm Spindle speed 6300 min-1 Tool holder SK 40 Manual swivel rotary table Tool holder Vice Accessories

x-travel: 350 mm y-travel: 240 mm z-travel: 340 mm turning speed range: 20 - 6.300 U/min feed speeds: 1 - 5.000 mm/min rapid traverse: 5 m/min tool taper: SK 40 power capacity: 6,3 / 10 kW control: Sinumeric 810 D tool change unit: pneumatisch manuell total power requirement: kW weight of the machine ca.: 1,6 t dimensions of the machine ca.: ca. 2 x 2 m 11065352834 5-sided universal milling machine Rotary table with swivel axis (clamping surface 400 x 290 mm) Rotation range C-axis displayed 360 ° on the screen B-axis swivel range +105 / -15 ° shown on the screen Table load capacity 100 kg, Operating modes 2 and 3, prepared for Net service, programming instructions included, RS 232 C interface Operating mode 4 (extended manual intervention) Accessories: coolant device, electronic handwheel Machine is workshop tested and with electrical Acceptance report The data for this ad was create ...

AMOB MAH 40/3 CNC 3-roll bending machine was built in 2021 in Portugal by AMOB Group. The machine, designed for bending tubes and profiles, ensures the highest precision and repeatability of the produced parts. The machining process is performed by three hardened rollers, of which the upper roller has hydraulic adjustment. Each of these is driven by a reliable, high-power motor, which is located inside a fully welded body. This solution enables bending of even the most complex shapes both vertically and horizontally. All this is complemented by an advanced CNC control with memory for numerous programmes. The MAH 40/3 CNC tube and profile bending machine weighs 540 kg. Technical specifications of the AMOB MAH 40/3 CNC bending machine - control panel with CNC control - number of rollers: 3 - roller diameter: 148 mm - roller rotational speed: 12 rpm - number of shafts: 2 - shaft di ...

Ref. -No.: 10164 Manufacturer: DECKEL MAHO Year of construction: 1986 Type of control: CNC Control: CNC 432 Storage location: Halberstadt Country of origin: Deutschland Total connected load: 40 kVA X-Travel: 800 mm Y-Travel: 450 mm Z-Travel: 500 mm Feed force (X, Y, Z): X 800, Y 24000, Z 8000 N Quill Stroke: 100 mm Speed work spindle: 20-4000 RPM Feeds X/Y/Z: 1-3000 m / min Rapid Traverse X/Y/Z: 8 m / min Tool Taper: ISO 40 Space requirements: 3680 x 3780 x 2720 LxWxH (mm) Further information: Additional information: - with controlled rotary table Ø800 (B axis) - simultaneously controlled axes: 3 - axes controlled one after the other: 4

Lid Maho DMC 64 V linear Year of construction 2003 The MMC was overhauled in October, as well as the rectifier. The spindle motor has been overhauled - The encoder is new as well as the glass scale in X. Location: Bochum

CNC Universal – Milling & Drilling Machine DECKEL MAHO DMU 80 P duoBlock With path control MILL PLUS iT Year of Make: 2006 Travel: X 800 Y 800 Z800 Speed range: 0 – 8,000 rpm infinitely variable ( SK 50 ) With the following accessories: NC rotary table 900 mm x 700 mm clamping surface (table load max. 1.4 t) Universal milling head with controlled B axis Universal tool changer with 40 magazine positions as a double gripper ( SK 50 ) Full protection cabin with sliding doors and interior lighting IKZ – 40 bar Conveyor Rotoclear Tool Measurement BLUM Laser 3 D Probe Heidenhain TS 641 Operating mode 3 + 4 Electronic handwheel 3-Piece Height Adjustable Machine Shoes Transport device Operating instructions