We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
121,993 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Description: Mobile low-noise compressor 53 - 60 DB (A) Delivery pressure 8 bar eff. Delivery rate 85/120 L / min Tank capacity 10 l / 8 bar l / bar Machine weight approx. 21 kg. Number of cylinders 2 pcs. Motor 230V / 0.75KW Dimensions L-W-H 465 x 380 x 575 mm Approx. Onsite Dimension. (l x w x h): 465 x 380 x 575 mm, weight approx.: 21 kg
used
Sägeblatt-Ø: 315 mm cutting diameter: 90 mm sawblade width: 2,5 mm capacity 90 degrees: round: 90 mm capacity 90 degrees: flat: 120 x 70 mm capacity 45 degrees: round: 80 mm capacity 45 degrees: flat: 80 x 70 mm turning speeds: 52 -104 U/min voltage: 400 V frequency: 50 Hz power capacity: 1,32 -1,9 kW weight of the machine ca.: 220 Kg range L-W-H: 0,7 x 0,6 x 1,3, m • mitre possibility by adjustment of the sawhead, • self-scrolled vise, self-ajdustable protection cover, • cooling pump with bin, • 2 steps of cutting speed • with under frame The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
I. Working capacity -Faceplate diameter 2000 mm -Workpiece max. diameter 2200 mm -Workpiece max. height: -under the cross rail 1850 mm -Workpiece max. weight 20 tons II. Movable cross rail : - Stroke on the column 1600 mm - Rapid moving speed 400 mm/min - Slow moving speed 10 mm/min III. Faceplate main drive in the turning mode. -Main drive motor power 60 kW -Faceplate speed range 250 rev/min IV. Working support: -Ram stroke (Z axis) 1500mm -Ram section 250x250 mm -Ram/taper ISO 50 -Tool magazine, tool number 16 (left tool magazine with milling tools and right tool magazine with turning tools or mixed) -Milling shaft drive motor power 37 kW -One tool holder max. Weight 30-70 Kg -Milling spindle speed 1 - 2000 rev/min V. Feeds -X, Z axes working feeds 1 – 6.000 mm -C – axis feeds (faceplate-milling mode) 0,001 + 2, 7 rev /min -Rapid feeds 10.000 mm/min ...
used
3516B Marine Auxiliary Engine 1345 kW / 1200 rpm
new
Chiller with refrigerant R454B < 500GWP. Cooling capacity according to Eurovent 34kW. internal pump, internal tank, coaxial evaporator, winter package up to an ambient temperature of -25°C, internal bypass. Delivery time approx. 6 weeks Also available with other cooling capacities.
used
Precast Modular House Machine, Low Cost Precast Concrete House our used lines meets after reinstallation by us the Definition RETROFIT ERICH PETER MACHINES-PLANTS GMBH A - 7083 Purbach - Austria Mobiltel.: +43-664-3358378 office@machines-plants.at www.machines-plants.at Affordable housing Low-cost housing - Hotels - housing estates - residential developments - residential areas & complexes – single housing – low cost housing Günstige Häuser - Low-Cost-Häuser, - Hotels - Wohnsiedlungen - Entwicklungen v. Wohngebiete und Komplexe - Einzelhäuser - preiswerte Wohnungen Cmodul-3D Austria we can offer NEW also C Module dim. 3000 mm x 6000 mm (c-module)NEW MOULDS Affordable houses - low cost living space Low cost housing I am proud to introduce now our improved system for the construction of affordable houses. S ...
used
? The machine is built in 2 construction works: 1250 x 2500 and 1500 x 3000. ? The IPG fiber laser resonator is available for this model with the power values 500 W, 1000 W, 1500 W and 2000 W. ? The beam is guided by a flexible light guide, i.e. cleaning and alignment of the mirror optics are not required. ? The HP SSL high-performance cutting head is very easy to set up. ? High cutting efficiency with low operating costs; Power consumption of only 13 kW for a 1-kW fiber laser source. ? The heavy machine frame and the high-stiff bruecke are designed as a tension-free welded construction and carefully manufactured. ? The interchangeable table with hydraulic lifting adaptation takes over the loading and removal of cut parts during the ongoing cutting process - re-training with further automation functions is possible. ? The working area is fully clad and illuminated, and the cutting ...
new
High-pressure cleaning device, high-pressure flusher, high-pressure built-in washer on hot-dip galvanized and painted high-quality steel frames with forklift flaps suitable for installation in company vehicles. PTC Whale 36/210, 43/180 or 55/160, similar but no workday & fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Whale 36/210 | 36l/min. at 210bar | Engine: Honda GX630 14.7kW Whale 43/180 | 43l/min. at 180bar | Engine: Honda GX630 14.7kW Whale 55/160 | 55l/min. at 160bar | Engine: Honda GX690 17.7kW DIMENSIONS / WEIGHT: Dimensions without water tank LxWxH: approx. 650x1.000x1.030 mm Empty weight without water tank: approx. 250 kg Dimensions and unladen weight with 300 l water tank: approx. 1,160x1,000x1,030 mm and approx. 280 kg Dimensions and unladen weight with 500 l water tank: approx. 1,260x1,000x1,030 mm and appr ...
new
High-pressure cleaning device, high-pressure flusher, high-pressure built-in washer on hot-dip galvanized and painted high-quality steel frames with forklift flaps suitable for installation in company vehicles. PTC Salmon 60/200 and 75/150 similar but no evening & Fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Salmon 60/200 | 60l/min. at 200bar | Engine: Vanguard 35 HP 26kW Salmon 75/150 | 75l/min. at 150bar | Engine: Vanguard 35 HP 26kW DIMENSIONS / WEIGHT: Dimensions without water tank LxWxH: approx. 700x1.250x1.200 mm Dimensions with 400l water tank LxWxH: approx. 1.300x1.250x1.200 mm Dimensions with 800l water tank LxWxH: approx. 2,000x1.250x1.200 mm Empty weight without water tank: approx. 300 kg Empty weight with 400l water tank: approx. 320 kg Empty weight with 800l water tank: approx. 350 kg HIGH-PRESSURE PUM ...
new
High-pressure cleaning device, high-pressure flusher, high-pressure built-in washer on hot-dip galvanized and painted high-quality steel frames with forklift flaps suitable for installation in company vehicles. PTC Moses 60/200, 75/150, 30/300, 75/210XL, 84/190XL, 102/150XL and 50/300XL similar but no evening & Fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Moses 60/200 | 60l/min. at 200bar | Engine: Kohler KDW 1404 26kW TIER III Moses 75/150 | 75l/min. at 150bar | Engine: Kohler KDW 1404 26kW TIER III Moses 30/300 | 30l/min. at 300bar | Engine: Kohler KDW 1404 26kW TIER III Moses XL 75/210 | 75l/min. at 210bar | Engine: Kohler KDW 2204 37.5kW TIER III Moses XL 84/190 | 84l/min. at 190bar | Engine: Kohler KDW 2204 37.5kW TIER III Moses XL 102/150 | 102l/min. at 150bar | Engine: Kohler KDW 2204 37.5kW TIER III Moses XL 50/30 ...
new
High-pressure cleaning device, high-pressure flusher, high-pressure built-in washer on hot-dip galvanized and painted high-quality steel frame with forklift load suitable for installation in company vehicles. PTC Dolphin 75/210, 84/190 and 102/150 similar but no evening & Fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Dolphin 75/210 | 75l/min. at 210bar Dolphin 84/190 | 84l/min. at 190bar Dolphin 102/150 | 102l/min. at 150bar DIMENSIONS / WEIGHT: Dimensions and weight without water tank LxWxH: approx. 1,240 x 1,300 x 1,300 mm, approx. 650 kg Dimensions and weight with 500 l water tank: approx. 1,850 x 1,300 x 1,300 mm, approx. 580 kg Dimensions and weight with 800 l water tank: approx. 1,950 x 1,300 x 1,300 mm, approx. 620 kg Dimensions and weight with 1000 l water tank: approx. 2,020 x 1,300 x 1,300 mm, approx. 640 kg ...
new
High-pressure cleaning device, high-pressure rinsing, high-pressure washer on hot-dip galvanized and painted high-quality steel frames with forklift slacks. PTC Tornado 60/200, 75/150, 75/210, 84/190 and 102/150 similar but no evening & Fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Tornado 60/200 | 60l/min. at 200bar | Engine: Kohler KDW 1404 26kW Tornado 75/150 | 75l/min. at 150bar | Engine: Kohler KDW 1404 26kW Tornado 75/210 | 75l/min. at 210bar | Engine: Kohler KDW 2204 37.5kW Tornado 84/190 | 84l/min. at 190bar | Engine: Kohler KDW 2204 37.5kW Tornado 102/150 | 102l/min. at 150bar | Engine: Kohler KDW 2204 37.5kW DIMENSIONS / WEIGHT: Dimensions and weight with 680l water tank LxWxH: approx. 2.300x1.310x1.310 mm, approx. 640 kg Dimensions and weight with 1000l water tank LxWxH: approx. 2.300x1.310x1.630 mm, approx. ...
new
High-pressure cleaning device, high-pressure flusher, high-pressure built-in washer on hot-dip galvanized and painted high-quality steel frames with forklift flaps suitable for installation in company vehicles. PTC Moses 60/200, 75/150, 30/300, 75/210XL, 84/190XL, 102/150XL and 50/300XL similar but no evening & Fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Moses 60/200 | 60l/min. at 200bar | Engine: Yanmar 3TNV88C 27.5kW Stage V Moses 75/150 | 75l/min. at 150bar | Engine: Yanmar 3TNV88C 27.5kW Stage V Moses 30/300 | 30l/min. at 300bar | Engine: Yanmar 3TNV88C 27.5kW Stage V Moses XL 75/210 | 75l/min. at 210bar | Engine: Yanmar 4TNV88C 35.5kW Stage V Moses XL 84/190 | 84l/min. at 190bar | Engine: Yanmar 4TNV88C 35.5kW Stage V Moses XL 102/150 | 102l/min. at 150bar | Engine: Yanmar 4TNV88C 35.5kW Stage V Moses XL 50/300 | 50 ...
used
NC machine table (X-axis) Travel speed: 0.1 - 30 m/min Travel range: 800mm Tip height: -K version .200 mm grindable workpiece ?: 10 - 250 mm Center width (max. workpiece length): 800 mm NC divider (A axis) possible divisions: 1-999 Accuracy: ?3 angular seconds Workpiece centering by centering tip: Version K MK3 Max. Speed: 80 min-1 NC grinding slide (Z-axis) Feed step: 0.001 mm Input fineness: 0.001 mm Travel speed: max. 2 m/min Travel: 335 mm NC shift axis (transverse movement of the grinding wheel Y-axis) Travel: ? 70 mm Travel speed: max. 1m/min Input fineness: 0.001 mm NC dressing device (B, U and W axis) Working area of the setter: 120 mm x 120 mm Numerically controlled axes: 3 Feed speeds: U-axis: 0-2500 mm/min W-axis: 0 - 2500 mm/min B-axis: 0 - 100 min-1 Step fineness: U-axis: 0.0005 mm W-axis: 0.0005 mm B-axis: 0.025? Grinding spindles (data are based on a maximum cutting speed ...
used
NC machine table (X-axis) Travel speed: 0.1 - 30 m/min Travel range: 800mm Tip height: -K version .200 mm grindable workpiece ?: 10 - 250 mm Center width (max. workpiece length): 800 mm NC divider (A axis) possible divisions: 1-999 Accuracy: ?3 angular seconds Workpiece centering by centering tip: Version K MK3 Max. Speed: 80 min-1 NC grinding slide (Z-axis) Feed step: 0.001 mm Input fineness: 0.001 mm Travel speed: max. 2 m/min Travel: 335 mm NC shift axis (transverse movement of the grinding wheel Y-axis) Travel: ? 70 mm Travel speed: max. 1m/min Input fineness: 0.001 mm NC dressing device (B, U and W axis) Working area of the setter: 120 mm x 120 mm Numerically controlled axes: 3 Feed speeds: U-axis: 0-2500 mm/min W-axis: 0 - 2500 mm/min B-axis: 0 - 100 min-1 Step fineness: U-axis: 0.0005 mm W-axis: 0.0005 mm B-axis: 0.025? Grinding spindles (data are based on a maximum cutting speed ...
new
DYNAJET 500th HELI Blue Performance INTRODUCTORY OFFER: If you want to be sure that this device is right for you, then we have a special offer for you: Crediting of rents for up to 6 months at 100% of the purchase price! For purchase: Including 1st UVV WITH arrival and maintenance (plus spare parts) on the same date (value approx. 1,500 net). The mobile and universally applicable dynaJET 500th cold and hot water high-pressure cleaner with up to 500 bar working pressure is characterized not only by its user-friendliness but also by its low weight, compact dimensions and high performance and safety level. Construction: • 1-axle chassis for easy manoeuvring • Self-supporting and indestructible framework for weight optimization • Central crane eyelet for optimal transport in hard-to-reach places • Frame in dip painting technology for high corrosion protection and hi ...
new
New machine GSL 180/180 Rotor diameter 180mm Rotor width 180mm Drive 3 KW Rotor blade 18 Weight approx. 140 KG The low-speed auxiliary mills of the GSL series operate at a low rotor speed and thus ensure low-noise operation. The high-quality regrind produced is largely free of dust content. The special rotor blades can be regrinded several times and no longer have to be adjusted in the auxiliary mill. The material to be shredded is fed via an inlet funnel manufactured in sandwich construction. An exchangeable sieve, which determines the final size of the ground material, closes the grinding chamber downwards. The material is discharged via a material collection container, which is manufactured in stainless steel as standard. In general, the material collection container is equipped with a connection for common vacuum systems. Advantages: Special rotor knives make adjustme ...
new
New machine GSL 180/300 Rotor diameter 180mm Rotor width 300mm Drehzal 150 min. Drive 4 kW Rotor blade 30 pieces Strator knife 2 Screen perforation 5mm Weight approx. 180 KG The low-speed auxiliary mills of the GSL series operate at a low rotor speed and thus ensure low-noise operation. The high-quality regrind produced is largely free of dust content. The special rotor blades can be regrinded several times and no longer have to be adjusted in the auxiliary mill. The material to be shredded is fed via an inlet funnel manufactured in sandwich construction. An exchangeable sieve, which determines the final size of the ground material, closes the grinding chamber downwards. The material is discharged via a material collection container, which is manufactured in stainless steel as standard. In general, the material collection container is equipped with a connection for common va ...
new
New machine GSL 180/430 Rotor diameter 180mm Rotor width 430mm Drehzal 150 min. Drive 4 kW Rotor blade 45 pieces Strator knife 2 Screen perforation 5mm Weight approx. 250 KG The low-speed auxiliary mills of the GSL series operate at a low rotor speed and thus ensure low-noise operation. The high-quality regrind produced is largely free of dust content. The special rotor blades can be regrinded several times and no longer have to be adjusted in the auxiliary mill. The material to be shredded is fed via an inlet funnel manufactured in sandwich construction. An exchangeable sieve, which determines the final size of the ground material, closes the grinding chamber downwards. The material is discharged via a material collection container, which is manufactured in stainless steel as standard. In general, the material collection container is equipped with a connection for common va ...
new
New machine GSL 300/400 Rotor diameter 300mm Rotor width 400mm Drehzal 150 min. Drive 7.5 kW Rotor blade 33 pieces Strator knife 2 Screen perforation 6mm Weight approx. 550 KG The low-speed auxiliary mills of the GSL series operate at a low rotor speed and thus ensure low-noise operation. The high-quality regrind produced is largely free of dust content. The special rotor blades can be regrinded several times and no longer have to be adjusted in the auxiliary mill. The material to be shredded is fed via an inlet funnel manufactured in sandwich construction. An exchangeable sieve, which determines the final size of the ground material, closes the grinding chamber downwards. The material is discharged via a material collection container, which is manufactured in stainless steel as standard. In general, the material collection container is equipped with a connection for common ...
new
New machine GSL 300/600 Rotor diameter 300mm Rotor width 600mm Drehzal 150 min. Drive 11 kW Rotor blade 48 pieces Strator knife 2 Screen perforation 6mm Weight approx. 950 KG The low-speed auxiliary mills of the GSL series operate at a low rotor speed and thus ensure low-noise operation. The high-quality regrind produced is largely free of dust content. The special rotor blades can be regrinded several times and no longer have to be adjusted in the auxiliary mill. The material to be shredded is fed via an inlet funnel manufactured in sandwich construction. An exchangeable sieve, which determines the final size of the ground material, closes the grinding chamber downwards. The material is discharged via a material collection container, which is manufactured in stainless steel as standard. In general, the material collection container is equipped with a connection for common v ...
new
NOE Alu L A lightweight system that can be used to work independently of the crane. The NOEalu L convinces as a real hand formwork, due to its low weight, high flexibility and durability. The low weight of 21 kg/m² Ensures long-term productive Work, even without a crane. The sturdy construction will meet the to cope with the stresses of everyday construction site life. Flexible thanks to a wide, Vertical or horizontal table assortment. The Alulock connects the various components of the system as reliable as it is escaped. The individual panels allow a concrete pressure of up to up to 60 kN /m². NOE Alu L A lightweight system, for work without crane. The NOEalu L convinces as an Hand formwork, due to low weight, high flexibility and durability at the same time. The low weight of 21 kg/m² ensures a permanently productive work, even without a crane ...
used
Yale GLP55VX V2514 Counterbalance Truck VX Series Designed for medium and demanding applications The Yale Veracitor VX Series is a feature-rich series of internal combustion engine forklifts that combines the highest levels of productivity, ergonomics and reliability with a low (total) cost of ownership. The 40-55VX models are designed to provide customers with choices to meet different application needs. Available in three model configurations: the Base model offers low initial cost without compromising performance, the Value model offers high performance with very low operating costs, and the Productivity model guarantees superior performance in heavy-duty applications. Load-sensing hydraulics (LSH) increases productivity and reduces fuel consumption by up to 15% (VDI test); In the "ECO-eLo" fuel efficiency mode, fuel consumption can be reduced by up to 20% without signifi ...
CharacteristicsSwing- Ø, max.450 mmWeight approx.10000 KgDrive power milling spindle9,5/5,5 kWDrive power main spindle15/11 kWDrive power second spindle15/11 kWNumber of Toolmagazine positions38 Speed max.12000 rpmSlewability of B-Axis+/-120 degreeMovements X / Z / Y455/800/+-105 mmMilling spindle upper side1 Input precision of C-axis on Counterspindle0,001 degreeSpindle speed 2nd Spindle max.6000 rpmInput precision of C-axis on Mainspindle0,001 degreeBar diametre52 mmSpeed max.6000 rpmMax. Turning Length800 mmMax machining diameter430 mmDimensions (L x W x H)4,17 x 2,5 x 2,5 (4,55 x 2,5 x 2,5) mGeneralTurning-milling centre SZM: Tool spindle, Spindle 1, Spindle 2 and Turret 2 (Milling); Control: CELOS - ERGOline Spindle 1 hobbing functionSpindle 1 hobbing function Gear machining or spline machining is possible by synchronizing the rotary tool spindle rotation on turret 1 with the spind ...
used
An articulated-arm robot with four axes of movement is offered. - Performance up to 550 cycles per hour - per load capacity - with a standard swivel range of 2x180°. - Small footprint - Compact in design, the Robogrip can also be accommodated in small areas and in low halls. - Precise and product-friendly motion sequences -Wide range of applications - Packing, palletizing, sorting - the robot can be used for many different purposes. - The Robogrip also performs demanding combination tasks reliably and safely. - Individual equipment Numerous different gripping tools are available for the Robogrip. So you can easily put together your individual robot that meets your requirements one hundred percent. -Low maintenance The Robogrip is characterized by low maintenance requirements and high availability. This is made possible by the maintenance-free servo drives and the low numbe ...
new
Soundproof Diesel Generator Set Emergency Generator Set Manufacturer: Lucla Type GLU-33-SK Specifications Continuous power: 30 kVA Standby power: 33 kVA Mains voltage: 400/230 V Amperage: 43.3 A Max. sound level: dB(7m) =78 Engine: KOFO Model: K4100D Intake system: naturally aspirated engine Fuel Injection System: Eddy Number of cylinders: 4 Displacement: 3,613 L Bore x stroke: 100x115 mm Compression Ratio: 20:1 Nominal speed: 1500 r/min Engine power: 33 kW Controller: Mechanical Starting voltage: 12 V Generator: Lucla Model: LU 184GS Phase: 3 Voltage: 400 V / 230V 43.3A Line type: 3 phase 12 cable, Y type Stock: 1 Power factor (cos f): 0.8 Frequency: 50 Hz Continuous power: 30 kVA / 24KW Arousal Type: Brushless, Self-Arousal Voltage Regulation: % ±0.5 Protection class: IP 23 Degree of insulation: H Altitude(above sea level): m =1000 Controller: ...
used
3 axis water jet machine 4000 Bar 3000 mm x 2000 mm All accessories will come with machine Level Pressure 4200 bar Maximum Operating Pressure 4000 bar High Pressure Flow Rate 2.3 Liter Electric Motor 37 KW Heat Exchanger Motor 0,37 KW Motor Speed 1500 rpm 50 Hz Safety Shutdown Circuits High oil temperature low oil level Low air pressure Low pressure pressure (water) Low pump pressure Electronic adjustment in the pressure range of 100 bar and 4000 bar Hydraulic Pump 71Cu Cm / 103Lt) Hydraulic Axial Piston Max Working Pressure 200 bar Cooling Water Flow Rate 30 Lt / min The most favorable inlet pressure 4 bar (water) Booster Pump Setting 12 bar (water) Physical Dimensions Height = 122 cm Width = 104 cm Length = 1813 cm Single Head Orfis Diameter 0.14, 0.18, 0.23, 0.25, 0.28 Pump Warranty Period (Hydraulic electronics) 2 years or 1000 hours
used
Tumbler screening machine, second-hand --> 3 screen decks for 4 fractions, in mild steel design; Screening area : 1.8 m² per deck. Closed, dust-proof circular design, easy to dismantle manually, low-noise and safe to work on; - Dust-proof and work-safe design - Low noise level of approx. 75db(A) - Low acceleration, long screen life - Low foundation load - Dynamic mass balancing - V-belt drive by electric motor 4.0 KW, 380-420 / 660-690 V at 50 Hz, 440-480 V at 60 Hz, protection class IP 55; - incl. 3 x ball knock cleanings; --> Pneumatic lifting device possible.
used
Description: Ceccato CSC 40 screw air compressor (under brand of Atlas Copco ) Technical data: max. working pressure : 8 bars free air delivery at reference conditions : 5400 m3/h working hours in total : approx. 35000 hrs. working hours under load: approx. 18000 hrs. rated power : 30 kW ATLAS COPCO airend! dimensions: (LxWxH) : 1247x1060x1630 weight : 695 Please also take a look of video of the machine! Other features: CSC 40 compressor is compact, easy to install, solid, they have great performance and last but not least, they need very low maintenance. Accessibility of all components makes service and cleaning very easy. Without any doubt the best choice for strong, carefree and economical compressed air throughout your workplace. Key Benefits: DRD 75 IVR DRY outstanding, first-class components compact design all service components located at the front for excellent ac ...
used
Precast - Wall - Filigree - factory. Good as new circulation system: 60 pallets with 3.5 mx 8 m, 3 x lateral transport of pallets - Facilities, 1 x vibrated concrete station, new control - Beckhoff. Concrete distributor Crane 1.4 m³. Friction wheels. Roller blocks. Planning and installation as required. Formwork on request. Is dependend on the application. For low cost housing, cmodul austria low cost housing Affordable housing Low-cost housing Mixing system 1 m³ at extra charge. Tilting device if needed for concrete slabs vertical-tansport at extra charge. Cran for stock handling at extra charge. Projects for social housing are our daily work. Civil work plans, drawings and calculations, we can create for you. Similarly, profitability calculations.
used
C33 D5 Enclosed A044B089 Genset Model C33 D5, 33kVA Standby, 30kVA Prime, X3.3G1, Diesel, Enclosed Emergency Standby Power (ESP) Emissions Level : No Certification Local Codes and/or Regulation : CE Output Voltage : 400/230, 3 Phase, Wye, 4 Wire Engine X3.3G1 Engine Air Cleaner - Duty Rating : Normal Duty Engine Oil Heater : None Supplied Engine Speed Governing : Mechanical Droop Governor Engine Coolant Heater : 240V Sub-Base Anti-Vibration Mounts None Supplied Main Generator PI144G, 12 Leads, 50 Hertz (Hz), 380 - 416V, 163C, Emergency Standby Power (ESP) Main Generator Heater : None Supplied Genset Housing Sound Attenuated, Steel, Munsell Green Exhaust System Silencer Grade : Enclosure Critical Cooling System Genset Mounted Radiator, 50C / 122F, Genset Mounted Engine Coolant Mixture : 50% Antifreeze, 50% W ...
new
C38 D5 Enclosed A044B090 Genset Model C38 D5, 38kVA Standby, 35kVA Prime, X3.3G1, Diesel, Enclosed Emergency Standby Power (ESP) Emissions Level : No Certification Local Codes and/or Regulation : CE Output Voltage : 400/230, 3 Phase, Wye, 4 Wire Engine X3.3G1 Engine Air Cleaner - Duty Rating : Normal Duty Engine Oil Heater : None Supplied Engine Speed Governing : Mechanical Droop Governor Engine Coolant Heater : 240V Sub-Base Anti-Vibration Mounts None Supplied Main Generator PI144H, 12 Leads, 50 Hertz (Hz), 380 - 416V, 163C, Emergency Standby Power (ESP) Main Generator Heater : None Supplied Genset Housing Sound Attenuated, Steel, Munsell Green Exhaust System Silencer Grade : Enclosure Critical Cooling System Genset Mounted Radiator, 50C / 122F, Genset Mounted Engine Coolant Mixture : 50% Antifreeze, 50% W ...
new
C110 D5 Enclosed A040P845 Genset Model C110 D5, 110kVA Standby, 100kVA Prime, Enclosed Emergency Standby Power (ESP) Emissions Level : No Certification Local Codes and/or Regulation : CE Output Voltage : 400/230, 3 Phase, Wye, 4 Wire Engine 6BTA5.9G5 Engine Air Cleaner - Duty Rating : Normal Duty Engine Speed Governing : Isochronous Electronic Governor Engine Coolant Heater : 240V Sub-Base Anti-Vibration Mounts None Supplied Main Generator UC274C, 12 Leads, 50 Hertz (Hz), 190 - 208V and 380 - 416V, 163C, Emergency Standby Power (ESP) Generator Accessories Voltage Regulator - Torque Match Main Generator Heater : None Supplied Genset Housing Sound Attenuated, Steel, Munsell Green Exhaust System Silencer Grade : Enclosure Critical Cooling System Genset Mounted Radiator, 50C / 122F, Genset Mo ...
new
C150 D5 Enclosed A047W023 Genset Model C150 D5, 150kVA Standby, 136kVA Prime, Enclosed Emergency Standby Power (ESP) Emissions Level : No Certification Local Codes and/or Regulation : CE Output Voltage : 400/230, 3 Phase, Wye, 4 Wire Engine 6BTAA5.9G6 Engine Air Cleaner - Duty Rating : Heavy Duty Engine Speed Governing : Isochronous Electronic Governor Engine Coolant Heater : 240V Sub-Base Anti-Vibration Mounts None Supplied Main Generator UC274E, 12 Leads, 50 Hertz (Hz), 190 - 208V and 380 - 416V, 163C, Emergency Standby Power (ESP) Generator Accessories Voltage Regulator - Torque Match Main Generator Heater : None Supplied Genset Housing Sound Attenuated, Steel, Munsell Green Exhaust System Silencer Grade : Enclosure Critical Cooling System Genset Mounted Radiator, 50C / 122F, Genset Mounted Engine Co ...
new
C170 D5 Enclosed A047W024 Genset Model C170 D5, 170kVA Standby, 155kVA Prime, Enclosed Emergency Standby Power (ESP) Emissions Level : No Certification Local Codes and/or Regulation : CE Output Voltage : 400/230, 3 Phase, Wye, 4 Wire Engine 6BTAA5.9G7 Engine Air Cleaner - Duty Rating : Heavy Duty Engine Speed Governing : Isochronous Electronic Governor Engine Coolant Heater : 240V Sub-Base Anti-Vibration Mounts None Supplied Main Generator UC274F, 12 Leads, 50 Hertz (Hz), 190 - 208V and 380 - 416V, 163C, Emergency Standby Power (ESP) Generator Accessories Voltage Regulator - Torque Match Main Generator Heater : None Supplied Genset Housing Sound Attenuated, Steel, Munsell Green Exhaust System Silencer Grade : Enclosure Critical Cooling System Genset Mounted Radiator, 50C / 122F, Genset Mounted Engine Co ...
new
C500 D5 Enclosed Genset Model Item C500 D5, 500kVA Standby, 455kVA Prime, 0, 0, QSZ13G5, Diesel, Enclosed Emergency Standby Power (ESP) Emissions Level : EU SII Local Codes and/or Regulation : CE Output Voltage : 400/230, 3 Phase, Wye, 4 Wire Engine QSZ13G5 Engine Air Cleaner - Duty Rating : Normal Duty Engine Speed Governing : Isochronous Electronic Governor Engine Coolant Heater : 240V Sub-Base Anti-Vibration Mounts None Supplied Main Generator HC5C, 12 Leads, 50 Hertz (Hz), 190 - 220V and 380 - 440V, 163C, Emergency Standby Power (ESP) Generator Accessories Voltage Regulator - Torque Match Main Generator Heater : None Supplied Genset Housing Sound Attenuated, Steel, Munsell Green Exhaust System Silencer Grade : Enclo ...
used
Waste Baler BTS-MF300LH The BTS-MF300LH and BTS-MF500LH Low Height Waste Balers are ideal for compacting loose cardboard, paper, film, plastic and metal containers and many materials more. The waste balers impressing with their low height, ease of use and large filling volume. Finished bales can be easily removed from the baler with the automatic bale ejector. - Bale weight output of up to 340 kg - Compact and low design with only 1986 mm height - Suitable for baling of cardboard, film, clothes and many materials more - Automatic bale cycle - Retaining claws to prevent spring back - Fully automated bale ejector simplifies removal of bale - Maximum safety standards - CE-certified - Quality product Made in Europe Pressing force: 20 Ton Motor: 2.2 kW 16 Amp Power supply: 220-230 V (1 Phase) Machine size: (H x W x D) 1986 x 1800 x 1100 mm Transportation height: 198 ...
new
- Preliminary guide! - 20 operating hours - fully functional - Visit possible by appointment in Kaiserslautern Technical data and information: Ideal CO2 laser for small to medium production volumes Compact laser system with a working area that is slightly larger than DinA3. The entire system is designed as a table. Despite the small size, this CO2 laser offers uncatchable functionality in order to be able to cut and engrave professionally. For slightly more lax parts, there is the possibility to push the factory quilts horizontally. Due to the low construction size, this CO2 laser can easily be used on the go. Properties: - 30 and 60 watt laser source from Synrad with extremely long life - small and compact dimensions - extremely reprosable stepper motor drive - automatic Z-axis with autofocus function - Pilot beam for reading positions - Air-Assist to protect the ...
used
Waste Baler BTS-MF500LH The BTS-MF300LH and BTS-MF500LH Low Height Waste Balers are ideal for compacting loose cardboard, paper, film, plastic and metal containers and many materials more. The waste balers impressing with their low height, ease of use and large filling volume. Finished bales can be easily removed from the baler with the automatic bale ejector. - Bale weight output of up to 500 kg - Compact and low design with only 2249 mm height - Suitable for baling of cardboard, film, clothes, cans, PET, Canister, Big Bags and many materials more - Automatic bale cycle - Retaining claws to prevent spring back - Fully automated bale ejector simplifies removal of bale - Maximum safety standards - CE-certified - Quality product Made in Europe Pressing force:50 Ton Motor: 11 kW 32 Amp Power suppl: 380-400 V (3 Phase) Machine size (H x W x D): 2249 x 2041 x 1350 mm Tr ...
new
New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption ...
new
New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption ...
new
New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption ...
new
New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption ...
new
High-pressure cleaning device, high-pressure rinsing, high-pressure washer with suction device on hot-dip galvanized and painted high-quality steel frame with forklift tabs. The following models are available: Vortex Combi 800 Sewer B - 800 l sludge tank - 2750 l/min. suction capacity - Petrol engines: for sucking Honda GX390 8.8kW and for cleaning - Honda GX690 17.9kW Vortex Combi 1000 Sewer D - 1000 l sludge tank - 3600 l/min. suction capacity - Diesel engines: for sucking Yanmar L100 8.0kW and for cleaning Kohler KDW 1003 18.9kW HIGH PRESSURE PUMP 160 bar at 55 l/min. Manufacturer: COMET Model: TW Premium Cxr8gqdby HIGH-PRESSURE HOSE REELS: Type: manual hose reel Material: Stainless steel • Capacite: max. 50 m 1/2" high-pressure hose Hose: 50 m 1/2" high-pressure hose (included) LOW-PRESSURE WATER SUPPLY HOSE REEL: Type: manual hose reel Material: Stai ...
used
DYNAJET 500th HELI with approx. 4,250 operating hours, price 22.000€ (net) The mobile and universally applicable dynaJET 500th cold and hot water high-pressure cleaner with up to 500 bar working pressure is characterized not only by its user-friendliness but also by its low weight, compact dimensions and high performance and safety level. CONSTRUCTION • 1-axle chassis with pneumatic tires for easy manoeuvring on site • Self-supporting and indestructible framework for weight optimization • Crane eyelet for easy transport and handling • Underrun protection for additional safety • Frame in dip painting technology for high corrosion protection and highest surface quality • Targa concept with separation between the unit side and the operating side for enormous advantages in ergonomics, overall machine safety and noise reduction • Impact-resistant plastic hood for mi ...
used
DYNAJET 500th HELI with approx. 800 operating hours, price 38.000€ (net) The mobile and universally applicable dynaJET 500th cold and hot water high-pressure cleaner with up to 500 bar working pressure is characterized not only by its user-friendliness but also by its low weight, compact dimensions and high performance and safety level. CONSTRUCTION • 1-axle chassis with pneumatic tires for easy manoeuvring on site • Self-supporting and indestructible framework for weight optimization • Crane eyelet for easy transport and handling • Underrun protection for additional safety • Frame in dip painting technology for high corrosion protection and highest surface quality • Targa concept with separation between the unit side and the operating side for enormous advantages in ergonomics, overall machine safety and noise reduction • Impact-resistant plastic hood for mini ...
used
DYNAJET 500th HELI with approx. 1,450 operating hours, price 33.000€ (net) The mobile and universally applicable dynaJET 500th cold and hot water high-pressure cleaner with up to 500 bar working pressure is characterized not only by its user-friendliness but also by its low weight, compact dimensions and high performance and safety level. CONSTRUCTION • 1-axle chassis with pneumatic tires for easy manoeuvring on site • Self-supporting and indestructible framework for weight optimization • Crane eyelet for easy transport and handling • Underrun protection for additional safety • Frame in dip painting technology for high corrosion protection and highest surface quality • Targa concept with separation between the unit side and the operating side for enormous advantages in ergonomics, overall machine safety and noise reduction • Impact-resistant plastic hood for mi ...
used
Description Rotary vane vacuum pump Becker KVT 3.140 from year of construction 2011, completely revised June-2014, since then stored – robust and completely oil-free vacuum pump – with simple construction, direct drive and only one shaft – guarantees longevity and low maintenance and operating costs – integrated intake filters and regulating valves – problem-free installation of accessories – optional corrosion protection – low noise emission – low heat radiation Technical data – Frequency: 50/60 Hz – maximum pumping speed: 129/154 m³/h – max. vacuum: 100/200 mbar abs. – motor power: 3.3 /4.40 kW
used
The OE750 spark spectrometer and the new OE720 are metal analyzers with new, groundbreaking performance features. With them, you can analyze all elements found in metals at low detection limits and with state-of-the-art multi-CMOS technology. Ever stricter requirements, complex supply chains and the increasing use of scrap as a base material are forcing foundries and the metalworking industry to reliably detect the lowest ppm values of traces and accompanying elements. Until now, spark spectrometers in these power ranges have been unwrive for many. With the OE series, this has now changed fundamentally. Hitachi OE spark spectrometers analyze all essential alloying elements and extremely low levels of trace, accompanying and treatment elements in metals, e.B nitrogen in steel. The OE750 also covers rare applications such as oxygen in copper and oxygen, nitrogen and hydrogen in titan ...
used
used baler Manufacturer: PAAL Type: LIKON 80 60 Year of construction: 2001 Operating hours: 37,056 h (on 12.10.2021) Specifications: Length: approx. 9405 mm Width: approx. 4050 mm Height: approx. 2500 mm Press weight up to: approx. 13 tons Pressing force at 300 bar: 60 t Filling opening: approx. 160 x 92 cm Channel cross-section: 100 x 80 cm Operating voltage: 400 V/3/N/PE/50 Hz Machine complete for continuous operation, including: Press box, complete with: - master press cylinders, - press hoppers, - closed sewer side walls, - 8 x 40 kg wire unwinding devices, - automatic channel adjustment, - bale length meters, - Synthetic resin coat in light blue according to RAL 5012 Hydraulic power pack, complete with: - low-maintenance and low-pipeline hydraulics, - a high-pressure internal gear pump 520 Ltr./h flow rate, drive 75 kW, - ...