low loader used for sale

Stock number: H046, Low pressure homogenizer, stainless steel,, Gaco type AL., 1-stage., 0,75 HP motor,, 220/380 V., Theoretical capacity 600 l/h., The homogenizer has not been used., Material: Stainless steel AISI 304

Electric walker trucks, low-floor pallet trucks, ants, pedestrian stackers JUNGHEINRICH type EJE 116Masch. No: 90281103 year of construction 2007Nominal load capacity: 1600 kgLifting height: 200 mmFork length: 1150 mmOperating voltage: 24 VoltTotal length: 1750 mmTotal width: 730 mmHeight with drawbar: 1300 mm- Battery from year of construction 2013, type 24V 2PzS 250 (24 Volt, 250 AH)- Battery automatic charger- 5575 operating hours read. Weight approx. 560 kggood condition; used

Electric walking forklift, low-floor pallet truck, ant, pedestrian stacker JUNGHEINRICH type EJE 22G-20-235-56 (L)Masch. No.: 80405795 year of construction 1996Nominal load capacity: 2200 kgLifting height: 200 mmFork length: 2350 mmOperating voltage: 24 VoltTotal length: 3050 mmTotal width: 690 mmHeight with drawbar: 1350 mm- Battery from year of construction 2007, Type 2 EPZS 230 (24 Volt, 230 AH)- Battery automatic charger- 8890 operating hours read. Weight approx. 560 kggood condition; used

Electric walking forklifts, low-floor pallet trucks, ants, pedestrian stackers JUNGHEINRICH type EME 112Masch. No: 90145339 year of construction 2005Nominal load capacity: 1200 kgLifting height: 200 mmFork length: 1170 mmOperating voltage: 24 voltsTotal length: 1550 mmTotal width: 700 mmHeight with drawbar: 1300 mm- 2 pieces traction batteries NEW from year of construction 2024, type 12 volts, Ah 55- integrated automatic charger, type E 230 G 24/6 (24 volts, 6 amps)Weight: approx. 175 kggood condition; used

A total of 12 low-voltage motors are available, 4x SIMOTICS SD 1LE5 and 8x SIMOTICS SD 1LE1. (1) SIMOTICS SD 1LE5, Motor type: Three-phase asynchronous motor, low voltage, cast iron housing, Severe Duty series SIMOTICS SD (model range 1LE5), protection class: standard IP55, insulation class: Class F, operating mode: continuous duty S1 according to IEC/DIN EN 60034-1, environment: -20°C to 40°C, up to 1000m above sea level. (2) SIMOTICS SD 1LE1, rated voltage: standard voltages, operating mode: continuous duty S1, housing: cast iron (Severe Duty), cooling: self-ventilated, insulation class: F (temperature class 155 / utilization B), speed range: 750-3600/min, max. rated torque: approx. 1703 Nm. The motors are still unused, the year of construction is 2021/22. An on-site inspection is possible.

Equipment: Spacious interior with stainless steel shelves and doors for optimal sample organization Strong insulation for constant temperature even in the event of a power failure Digital control element with temperature display RS232 interface for external monitoring and data acquisition Robust castors for easy transport Condition: Used, functional With slight signs of wear (see pictures) Interior clean and fully equipped

Lower filling pipe, previously used on a Tetra Pak A3 Flex 250 ml Slim 100V., Type of Machine: Aseptic carton filling machine, Dimensions: 84 x 9 x 9 cm, Weight: 2 kg

Upper support, upper slide, dovetail guide, tool slide, cross table, support slide, support carrier, slide guide -Tool slide: Support slide lower part support carrier -Dovetail: 90 to 73 mm 12 mm high -Dimensions: see photos -Quantity: 5x bottoms available -Price: per piece -Dimensions: 210/180/H25 mm -Weight: 4 kg/piece

Ultrasonic sensor, ultrasonic generator, ultrasonic transducer, ultrasonic plastic welding machine, lowering unit for ultrasonic welding machines, lowering unit - flatbed -Manufacturer: Nucleus, lowering unit - flatbed for ultrasonic welding machines -Eco FR360102 -Servomotor: NuDC42I25R-1000 Voltage 24 V -Number: 5x lowering unit available -Price: per piece -Dimensions: 340/240/H130 mm -Weight: 4.5 kg/pc.

Ultrasonic sensor, ultrasonic generator, ultrasonic transducer, ultrasonic plastic welding machine, lowering unit for ultrasonic welding machines, lowering unit - flatbed, lowering column -Manufacturer: Nucleus, Absen column 35 for ultrasonic welding machines -Eco FR361101 -Servo motor: Dunkermotoren GR 42x40, voltage 24 V -Receiver: Shaft Ø 20 x 18 mm see photo -Number: 4x lowering unit available -Price: per piece -Dimensions: 250/220/H85 mm -Weight: 2.3 kg/pc.

Ultrasonic sensor, ultrasonic generator, ultrasonic transducer, ultrasonic plastic welding machine, lowering unit for ultrasonic welding machines, lowering unit - flatbed, lowering column -Manufacturer: Nucleus, Absen column 35 for ultrasonic welding machines -Eco FR361101 -Servo motor: Dunkermotoren GR 42x40, voltage 24 V -Receiver: Shaft Ø 20 x 18 mm see photo -Dimensions: 270/230/H85 mm -Weight: 2.5 kg

DURENDUS 200 T Deep Drawing Press – Double Column Press – 900 × 900 mm Table, 80 T Drawing Cushion The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic thermoforming press with integrated drawing pad function for forming processes, drawing work and precise sheet metal processing. Base price: 76000 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. T-slots and drilling patterns according to customer specifications Ad ...

Ultra Low Temperature Freezer ULT -86°C / 100 liters HAIER DW-86L100J Year of manufacture: 2020 Capacity: 100 l Temperature range: Min: -86 °C / Max: -40 °C Inner Dimensions: 330mm481mm630mm (WWH) External Dimensions: 770mm660mm810mm (WWH) Noise level: 46.8 dB Weight 108 kg Applications: Laboratory Number of doors: 1 door 2 compartments Direct cooling Defrost Mode: Manual Equipment tested at -50°C and -80°C

Lifting height 235 mm/ unused and in original packaging Auction-ID: A1-46698-347

Lifting height 235 mm/ unused and in original packaging Auction-ID: A1-46698-348

Lifting height 265 mm/ unused and in original packaging Auction-ID: A1-46698-349

Lifting height 265 mm/ unused and in original packaging Auction-ID: A1-46698-350

(dr) Crane with 3 bins (dr) Hydraulic quick coupler CW10 (dr) Long arm (dr) papers available (dr) Start, drive and do what it's supposed to do Auction-ID: A3-43534-11426

Bobcat E85 Hydraulic quick coupler CW10 3 bins (Slots, Teeth, trunk Hose bridge system for lifting and hoisting start, drive and execute what it needs to do Auction-ID: A3-43534-11424

With disaster provision. Dimensions 401x185 in 2700kg. Lowered version. Trailer is still stitched, needs to be removed by the new buyer. Drawbar repair is required! ( improperly repaired )! New repair required, fixer-upper! Last inspection valid until 01/03/2027. Auction-ID: A3-44485-17002

Can tow 20 tons Turbo impact engine papers available does what it's supposed to do Low hours Auction-ID: A3-43534-11953

115 V / 230 V Transformer - Ref 6703 Manufacturer: Lowe Serial Number: 47661 Overall dimensions (W x D x H): 145 x 110 x 120 mm Weight: 10 kg Incoterm: FCA Auction-ID: A1-47051-165

Stainless steel brewing vessel as a wort kettle and whirlpool combination with an external boiler., Additional title: brew vessel from stainless steel, Total volume: 260 hl, Diameter approx.: 3 m , Diameter incl. insulation approx.: 3 m, Frame height: approx.: 2 m, Width: 3,4 m, Material: stainless steel 1.4301 (AISI 304), Base construction: on stainless steel pipe supports, ground pegged, Features: external boiler, conical hood stainless steel, D = 3200 mm), conical insulating hood (stainless steel outside diameter = 3400 mm), 2 outlets DN200 und DN100, manhole DN600, outlet vent (12000 mm), interior lighting

Auction-ID: A1-46873-117

Perfectly working 2 axle Chieftain. Can be used for: sand and gravel, sifting coarse material, construction and demolition waste, compost and biomass and agricultural applications. This sorts materials by size so that you can make pure soil, reusable stone/gravel fractions and separate waste into usable streams. Auction-ID: A3-43539-7842

Auction-ID: A1-47205-2162

Auction-ID: A1-47205-2193

Solid and professionally executed diesel generator of the brand Himoinsa, type HYW35, powered by a reliable Yanmar diesel engine. Equipped in a low-noise canopy and suitable for site, industrial and emergency power applications. The generator is equipped with both 230V and 400V connections and has a digital control panel. Compact but powerful unit with a decent transportable size. Engine is running. Vendor can load for transportation – PROS: Professional low-noise design Reliable Yanmar diesel engine Suitable for continuous operation Multiple 230V and 400V outputs Compact and easy to deploy on site or event Sturdy metal housing - Notes: Signs of wear and light scratches/dents according to age and use Auction-ID: A3-43544-10030

Equipped with: Suitable for Fendt 500 series, with attachments, hydraulic hoses and connections. Mechanical self-levelling front loader for tractors of approx. 90–120 hp with a dead weight of approx. 540 kg, maximum lifting height of approx. 4.07 meters, lifting capacity around 1,730–2,160 kg, breakout force of approx. 2,260 kg, hydraulic working pressure of 185 bar, required oil flow of approx. 60 l/min and a total length of approx. 3.5–4.0 meters. Auction-ID: A1-40139-243

Equipped with: with attachments, hydraulic hoses and connections. Auction-ID: A1-40139-244

The new Omap AT series of three-phase hopper loaders guarantees maximum reliability in the handling of plastic pellets, even over long distances. New Omap - AT series of 3-phase hopper loaders Model AT03-R30G-FT (2024) - (1a) Auction-ID: A1-47049-75

New Omap - AT series of 3-phase hopper loaders Model AT03-R30G-FT (2024) - (2a) The new Omap AT series of three-phase hopper loaders guarantees maximum reliability in the handling of plastic pellets, even over long distances. Auction-ID: A1-47049-76

EMCO - Loading arm 4 inches - used - as spare part carrier

Technical data: Loads Load: 70 kg Additional load: 20 kg Workspace: Max range: 1720 mm More info and versions: Number of axes: 4 Repeat accuracy: +/-0.1 mm Weight: 1050 kg to 1200 kg

blower power: 19 kW motor: . bucket: Diesel . The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications load Bearing load: 80 kg Further data and types Number of axes: 3 Repeatability: +/-0.1 mm Weight: 1200 kg

Rotary vane vacuum pump /// oel circulation lubricated Manufacturer: Busch Type: RC 0100B End pressure: approx. 20mbar suction power: approx. 100m3/h Status:Generalueberholt If you have any questions about this information or general questions about vacuum generation, we are happy to provide you with your services;

Pallet fork (fork length 1000 mm) with carriage / ballast weight three-point hitch

for material Ã?: 6-80 mm for rod lengths: 100-915 mm Recording size: 945 x 800 mm Working height: 1400 mm height adjustment: +/-200 mm Electr. Connection: 220 V Space requirements: 3420 x 1150 x 1500 mm Weight: 300 kg

Country of origin: Germany, L max mm: 3.2, Operating hours: 0

was connected to Gildemeister GMC 20

new all stainless steel discharging height ± 1.770 – 2.250 mm mobile

YEAR: 1989 CNC: FANUC 0T TORNIBILE: 300 mm TURNBACK LENGTH: 300 mm MANDRINO: MANDRINO ATTACK: 6 ASA BARRA CAPACITY: 56 mm ROTATION SPEED: 3240 rpm POWER: 26 Kw AXIS C: 360 degrees I TORRETTA: PORTASSTATION STATIONS: 12 Nr. MOTORS: 6 Nr. MANDRINO: MANDRINO ATTACK: 6 ASA ROTATION SPEED: 3240 rpm. POWER: 26 Kw AXIS C: 360 degrees The TORRET: PORTASSTATION STATIONS: 12 Nr. RELATED: 6 nr

NEW ! all stainless steel suitable for eurobins of 200L discharging height : ± 700-900 mm 1,5 kW mobile ± 300 kg dimensions (l x w x h) : ± 1.800 x 1.100 x 1.300 mm

Spindle circle 165 mm Interface Gildemeister GM 16 AC

Palletizer KRONES PRESS UNI, production year 2007 Along with the conveyors presented in the layout. • Palletizer for collective packages, capacity: approx. 50 pallets / h for specific palletizing formats, • Top loading, packs served in 2 tracks, • Pallet magazine, • A feeder for cardboard pads with a magazine for cardboard pads, • Control cabinet based on Siemens S7 control, • A platform for the operator in accordance with the dimensions presented in the layout, • Operator Panel, Packs and pallet conveyors in accordance with the presented layout 1. Empty pallets infeed conveyors 2. Packs conveyors

Loading caterpillar Hanomag D 600 functional, top engine