kw used for sale

Up to a total of 3 BMB KW 38PI / 3450 machines are sold in perfect condition. Manufactured in 2003. For more information about the price contact me by whatsapp or call. Clamping force 380 T Screw diameter 75 mm Tie bar spacing (H) 1025 mm Tie bar spacing (V) 945 mm Shot volume 1725 cm³ Shot weight 1640 g Pressure on material 2000 bar Robot interface Mould size 250-750mm ------------------- Length x width x height 8405.0 × 2040.0 × 2750.0 Weight 19000 kg

Auxiliary vehicle, type KW1VEK Bearing No.: akw885 Make: Möhringer Year of construction: 1997 Part number: 126 422 00 Specifications: Gauge: 980 (mm) Support height: 420 (mm) - Reinforced design - Circumferential chain - Driven by worm gear motor with built-in slipper clutch - Tilting stool - Adjustable trunk holder - Cables and cable balancing

The Metalbud Nowicki KWP-500 cooking kettle, is versatile device and can handle the cooking of meats, sausages, and various other edibles like vegetables or seafood. It uses steam for heating and boasts a 500l tank volume. The entire unit is made from stainless steel, guaranteeing optimal cleanliness and hygiene. The kettle comes with an intuitive control panel, allowing users to easily modify both the cooking temperature and duration. Maximum current: 1A Electric: 1x230V, 50Hz Weight: 450kg

This Kenner KWJ 3020 C KMT Streamline SL-V 30 Waterjet cutting machine was manufactured in the year 2012 in Germany. It is equipped with a Kenner control unit.

NEW MACHINE With format sliding table 2.60m Saw blade 250-315mm swivel: 90-45 Planing width of 410mm 4 knife shaft reversible knife (no more adjustment) Dressing table length of 1800mm Pass-through height from 4-225mm Mill: 90-45 swiveltove to the rear Milling rpm: 3000/4000/5000/ 6000/8000 and 10000 rpm Altitude stroke 160mm Engine power: 3 motors 3 KW400 V (4.0 hp)S1 100% continuous operation SPECIAL PRICE: net Options: Scoring unit with motor Miter stop 900mm Integral safety rails 500mm Westcott Drill Chuck 0-16mm Long hole drilling device Eccentric tensioner Right and left running (milling) Engine 4.0 KW (5.5 hp)S1 100% Planing knife 410 HSS G&WJ-BA-410-HSS

Robust diesel generator with soundproofing on sled. 3-phase generator with harmonized arousal. Technical data: - Rated power 30 KVA - Diesel 495D, 4 cylinder water-cooled, 33.0 kW/45 hp - Consumption average 258 g/kWh - Electric start - Current 43.3 A - Frequency 50 Hz - Voltage 220V/3x400V - Cable outlet 40A with 20 m PUR cable 3PNE, circuit breaker 3phase, Operating hour counter - ATS (Automatic Transfer Switch) with automatic start repetition, Activation of the current cover, automatic shutdown in case of lack of oil pressure, Overheating, excessive speed - slide with 4 lifting eyelets, length approx. 2300mm, width approx. 1300 mm, height approx. 1600 mm, Weight approx. 900 kg Option at extra cost: - Distributor swells with suitable sockets at the end of the cable - Suspension Warranty: 2 years on all non-wear parts or 2000 operating hours, which is m ...

Technical data: Fruit wash, grind, pressing then the juice pasteurization and bag-in-box packaging pour performance up to 750 L/h incl. mounted hydraulic large box emptying wash grinding plant Kreuzmayr KWEM 1000 cover press Kreuzmayr KEB 500 Pasteur Kreuzmayr PA 750 oil bag-in-box fillers Kreuzmayr CBF 900, incl. 6-digit series bottling juice pump, strainer, 2 PCs. juice buffer tank 220 litre stainless steel base frame, Tandem chassis with tyres 195/50-10 plan building with gas spring lift for the two side walls, roll-over tarp back 4 PCs. crank rotating supports for the horizontal alignment of the System cleaner, air compressor and complete piping fix established

NEW MACHINE With format sliding table 2.60m Saw blade 250-315mm swivel: 90-45 Planing width of 320mm 3 Knife shaft reversible knife (no more adjustment) Pass-through height from 4-225mm Mill: 90-45 swiveltove to the rear Milling rpm: 3000/4000/5000/ 6000/8000 and 10000 rpm Altitude stroke 160mm Engine power: 3 motors 3 KW400 V (4.0 hp)S1 100% continuous operation WJ-500200 SPECIAL PRICE: net Options: Scoring unit with motor Miter stop 900mm Integral safety rails 500mm Westcott Drill Chuck 0-16mm Long hole drilling device Eccentric tensioner Right and left running (milling) Planing knife 320 HSS G&WJ-BA-410-HSS

Horizontal Milling Machine DIXI, Type 350 Mach. No. 350-16 Control: Dixi CNC 4400 Table dimensions: 810 x 810 mm table load: 2000 kg X/Y/Z: 1000 / 1000/1000 mm B-axis rotating table C-axis vertical round rotating table RPM: 10-3000 U / min Power: 18 kWh Table with 7 T-slots: 18 mm rapid traverse: 20-10000 mm / min taper ISO 50 Weight: 17 tons Accessories: Vertical milling head, vertical round table, angle rack, holders, etc.

If you are interested we will send you photos! MACHINE DESCRIPTION: The MAS tray packer is a packaging machine that folds and glues an open tray (from a cutting) around the product formation. FORMATION: The machine sets 2 x 5 = 10 Tetra packs per tray. Machine dimensions: 3500-4500mm long depending on infeed conveyor. 2008mm width; Height 2000mm Performance: max 10 trays/min Electrical connection: 5% 50 Hz, 3-phase, 230/400 volts, approx. 8kW Energy consumption: 6 kWh Frequency 50 Hz 2% active power 1.18 kW Volume < 80 dB Electrical equipment: brand products, in accordance with standard MAS machine no. 6017, built 06/2006 Cabinet: Make Rittal V2A firmly installed on machine Pneum. Equipment: Make Festo Glue device: Nordson (3.6 kg tank capacity) with 2 hose system; Glue order volume with proportinal valve Compressed air: 6 bar (dry, oil-free) Air consumption: approx ...

Exciters - pathogen - vibration sensor - unbalance unit Schenk 23st Types: D1S, D02, DF2, DF200S, DF02L, D3, DF401S, DF5L, DF5S, DF5V, DH75 Siebtechnik 10pcs Types: GR20 GR30, GR31, GR40, GR41S allis chalmers 4pcs Types: 3F1, 4D1, 4E1 Jost / Joest 3pcs Types: JR200, JU600, JR406 Krupp 3pcs Types: GR1, GR3 Friedrich / PWH 3pcs Types: UE20, UE45 KWE 1st type: RF225 Honert 1st Type: H2U30 COMESSA 3pcs Types: 7 and 5 Binder 2pcs Foot dimensions 6x120mm X 280mm

NEW MACHINE With Formatschiebetisch 2, 60m Saw blade 250-315 mm Swivel: 90 °-45 ° Planing width 410 mm 4 cutter Blade (no setting more) Dressing table length of 1800 mm Clearance height of 4-225 mm Milling cutter: 90 °-45 ° swivel to the rear Blower rpm: 3000/4000/5000/6000 / 8000 and 10000 RPM Vertical lift 160 mm Engine power: 3 engines 3 KW400 V (4,0 PS) S1 100% continuous operation WJ-500300 Special price: NET Options: Before scoring unit with motor Guide fence 900 mm Integral safety rail 500 mm Westcott Chuck 0-16mm Milling Eccentric clamp Right - and left-hand rotation (BUR) Engine 4.0 KW (5.5 HP) S1 100% Planer blade 410 HSS G & WJ-BA-410-HSS

1 x Werner & Pfleiderer model GK90-E intermeshing mixer, Original year of manufacture: 1989, Chamber volume 91 litre, Net batch weight: approx 71kg, PES #3 type rotors, pneumatic hopper, hydraulic drop door, GWK TCU. KWE GmbH full unidrive gearbox input speed 1500rpm, Output speed 48.5rpm with Thrige Electric 470kW, 1520rpm, 380V DC v/s motor, Complete with electrical controls and in good condition.

FOR SALE... 7 SETS-WARTSILA DIESEL 16V25 KW3800 YOB 1998 ENGINE AT TURKEY TO WHOM IT MAY CONCERN; WE VE 2 SETS WARTSILA DIESEL 16V25 KW3800 YOB 1998 ENGINES AT TURKEY PLS FIND ENGINES SPECIFICATION AT BELOW. ENGINE TYPE 16V25 RATED POWER 3800kW RATED SPEED 900r/min ENGINE NO. 3963/4080/4081/4093/4094/4184/4185 ENGINE RUNNING HRS 52200-78000HRS DIRECTION OF ROTATION CLOCKWISE YOB 1998 WE VE ADDATIONALY WARTSILA DIESEL 12V25 ENGINE RATED POWER 2760kW RATED SPEED 900r/min SERIAL NO. 3711 IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST of regards; Aliaga marine services : info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

1 x Werner & Pfleiderer model GK90-E intermeshing mixer, Original year of manufacture: 1989, Chamber volume 91 litre, Net batch weight: approx 71kg, PES #3 type rotors, pneumatic hopper, hydraulic drop door, GWK TCU. KWE GmbH full unidrive gearbox input speed 1500rpm, Output speed 48.5rpm with Thrige Electric 470kW, 1520rpm, 380V DC v/s motor, Complete with electrical controls and in good condition.

Qty. 1 Second-hand gas heated log furnace including hot shear Mfc.: ELHAUS Type: L250-90/135/4FK – WS250BD Built: 1999 Log dia.: 10” – 254 mm Log length: 5 – 7 m Billet length: 650 – 1300 mm Min. shear temperature: depending on the alloy approx. 340 – 400 °C Log temperature max.: 530 °C Heated by natural gas Hu=8.600 kcal/Nm³ Gas consumption: 234 kWh/tAl – 23.5 Nm³/t Al El. power: 130 kW Number of heating zones: 4 Number of circulating zones: 3 Dimensions of the furnace: 14.75 x 2.2 x 3.9 m - L x W x H Hot shear Recoil pressure: 0 – 100 bar Recoil stroke: 1.85 m Shear force: max. 1.69 MN at 210 bar Shear stroke: 360 mm Output pressure: max. 160 bar Output stroke: 325 mm Closing pressure: 210 bar Spreading stroke: 2 x 4.0 mm Dim.: Height above hallway: 2.9 m Length over everything: 3.95 m Width over everything: 2.65 m Hydraulic station Max. ...

Bending capacity: 3.5 mmBiegeleistung (VA): 2.5 mmBiegelänge: 2030 mmMotorleistung: 3.7 kWGrundausstattung and features: upper beam and bending flange on both sides about hydraulic angetriebenWinkel the upper cheek 45 ° PositioniersteuerungManuelle BiegewangenverstellungKlemmdruck of the top clamping, hydraulic, for both sides, Central regelbarManuelle UnterwangenbombierungStandardwerkzeugsatz (engine included) consisting of from:-split upper cheek tool portable 3 foot switch with a separate emergency rash button lower beam rail bending beam rail Backgauge 600 mm, manually verstellbar-CE - compliant

Recycling power, tyres/h Min 20/h Size of tyres Max R22.5 Pulling force, t 20 Duration of one extraction cycle 2 min Weight, t 1,8 Power, kW Dimensions LxBxH, mm 4700x1000x1700 Power consumption: 10 kWh/h

Built in 2009/2005 Size min. 100 x 120 mm Max 300 x 430 mm Thickness Film thickness 20-100 mµ Mechanical speed 25,000 CPH Equipment 10 stations rollstream ROS 1 VSE-ROS-ES-RE-300-KWE twin multi disc unwind station 4 MTD AWS OWK built in 2005 JET feeder 8 JEF-450-FVM SA190 built in 2005 foil wrapping machine CMC 2800 with two feeders built in 2009 twin stacker CMC

New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption  ...

CHIRON MODEL FZ18W MAGNUM 4 axisVertical machining center with rotopallet and double 4th axis20 TOOLSISO 40Toolchange: 2.1 sec Spindle: 20 - 8000 RPM, 18,5k kWX = 625Y = 400Z = 400Rapids 40m/minTable area: 2 x 900 x 470- TSUDAKOMA heavy duty double 4th axis (Japan) 360.000 pos.- original HAWE hydraulic unit - FANUC 0m be inspected under power in our warehouse.Mimu Machine tools Italy

New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption  ...

Rotary vane vacuum pump - oillubricated Manufacturer: Leybold Type: Sogevac SV 300 Cat. No.: 10931 Status: Generalueberholt Gewast.: 12 months Including: oil filling (mineral oil), operating instructions with list of parts Voltage: 50/60Hz 230-400/460V Engine nominal: 5.5 KWfinal pressure or gasbalast: approx. 0.08 m bar Delivery time: ready for use; ready for use

New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption  ...

Manufacturer: Solar Turbines INC, San Diego USA Model: Taurus 60 with Solonox combustion, Packager: Turbomach Version: T 7301 Yoc package: 1998 Turbine engine: new engine installed in 2012, only few hours since installation Condition: fully serviced and ready for start. Capacity: 5200 kW Speed: 14.944 U/min continual Fuel: Natural Gas and Light Diesel (dual fuel) Fuel consumption: 122.469 kJ/kWh Burners: 12 Start system: electro.hydraulic, 90 kW Outlet temperature: 486°C Exhaust gas: 21.244 kg/s

New device 12-month warranty Advantages of cooled ice water: + stable low bulk water temperatures + accurate dough temperature control all year round + fast swelling when mixing without ice + woolier dough seam through freshly cooled, liquid ice water + exact dosing via water mixing and dosing device possible + water-carrying parts are made of stainless steel cleaning-free + hygienically clean drinking water Langheinz ice water systems are characterized by: + consistently low water temperatures + powerful refrigeration machines + Refrigeration systems with expansion valve + electronic ice bank controllers + Stainless steel refrigeration evaporator + Multiple stainless steel water heat exchanger + insulated stainless steel ice water bath + Empty tap in the ice water bath + high flow rate + compact dimensions + easy-care surface structure + low energy consumption  ...

FOR SALE... WARTSILA DIESEL 12V25 KW2760 YOB 1993 ENGINE AT TURKEY TO WHOM IT MAY CONCERN; WE VE WARTSILA DIESEL 12V25 KW2760 YOB 1993 ENGINE AT TURKEY PLS FIND ENGINE SPECIFICATION AT BELOW. RATED POWER 2760kW RATED SPEED 900r/min SERIAL NO. 3711 MADE IN SWEEDEN CRANKSHAFT STD SIZE MEASURMENT. IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best of regards; Aliaga marine services : info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Technical specifications: automatic raw water supply: Exchange pump, frequenzgeregeltFördermenge: 40 m ³/hFörderdruck: barLeistung 2.5: 7.5 kWVorfiltration: Selbstreinigender filter with automatic SteuerungFilterfeinheit: 300 µmMaximaler flow rate: 40 m ³/hFlockungsstufe: flocculation tank: 2 x 0,5 m³ (material PP) charging pump, frequenzgeregeltFördermenge: 40 m ³/hFörderdruck: barLeistung 2.0: 5.5 kWRührwerke FlockungsbehälterDosierstelle for flocculant: static mix / Rohrflockulator (material PP) ) Ultrafiltration: number of UF modules: 8 Stck.Modulanordnung in the rack (x-series): 2Filterfläche of the UF modules: 60 m ² Backwashing and chemically supported backwash: Backwashing medium frequency-controlled RückspülpumpeNeutralisation: neutralisation tank: Material PENutzvolumen: 5.0 m³ material, shaft and stirrer: beschichtetDosierstationen steel: ...

Capacity: 35 t Folding length: 1200 mm CNC Brand: Delem CNC Model: M - 51 MACH-id   3969 MAKE        Baykal TYPE          APH YEAR         20.. SPECIFICATIONS Controll   Delem M-51 Pressbrake / Folding / Mech. / Hydr.   Pressbrake      Hydraulic / Mechanical     Hydraulic Bending length     1200 mm Distance between column   1070 mm Press force    35 Ton Throat    410 mm Stroke    60 mm Die height    470 mm Backgauge stroke X in mm500 mmNumber off controlled axis3Power4 kWDIMENSIONSLength1250 mmWidth1270 mmHeight2150 mmBaykal CNC Pressbrake

X 2000 mm Y 1700 mm Z 1250 mm W 730 Spindle diameter 110 mm kwW/Nm (S1) 19.5/951 3000 U/min Table 1400 x 1600 mm, table load 10 t T-grooves 22H8 Control HH 640 HR 510 ATC 40 H Coolant 70 bar on the power unit, with paper belt filter and oil separator Fixed cabin Spindle support 250 mm ISO 50 Immediately available!

Electric shrink tunnel 12 Electric thermal tube Electrical: 3 Phase, 24 kWt Weight: 420kg - 3-step heat isolation design for energy saving and operator protection. - Digital control, internal circulation keeps temperature consistent and shrinking effect perfect. - Equipped with high-level VFD(Variable Frequency Drive) that makes controlling of wind speed easy. - Unique wind board design makes controlling of wind direction easy and flexible, able to adapt to different bottles. - Durable electric heater tube ensures efficient heating. - Panel is embedded to prevent operators changing setting accidentally. - Heating can be stopped immediately, or maintained by time

X 4000 Y 2500 Z 1500 W 800 Spindle diameter 130 mm kwW/Nm (S1) 4pinacles 2099 3000 U/Min. Table size 2000 x 2400 mm, maximum table load 20 t T-grooves 22H8 HH 640 HR 510 Movable cabin Z800 Y1800 Spindle support 250 mm ISO 50 Immediately available!

properties Used belt conveyor from the manufacturer Blume Fördertechnik Colour: Blue Incl. drum motor Incl. feet Ideal for fast material transport Expertly dismantled and packaged Condition: fully functional 4 pcs in stock Technical data: Total length: 4.055mm Total width incl. motor: 600mm Total width without motor: 460mm Belt width: 400mm Belt type: Smooth BDL drum motor Engine type: 11s KW0.3 m/s0.30 belt conveyor The belt is ideal in the picking zone for interlocking machines or workstations and to optimize the internal process. During transport, the belt conveyor can transport sensitive and different sized containers, boxes or other packaging and article units to the feed-off or dispensing point and also serves, for example, as a connecting line in front of or between production and machining machines. It also enables efficient parts transport i ...

Table length: 1740 mm Table width: 650 mm Longitudinal X: 1500 mm Cross Y: 650 mm Vertical Z: 650 mm Positions ATC: 30   Positions APC: 0   CNC Brand: PC CNC Model: Fusion 640 M SPECIFICATIONS X - Travel  1500 mm Y - Travel  650 mm Z - Travel  650 mm bed / plano / portal / moving column   VMC Controll  PC-Fusion 640M Table Length x Width   1740 x 650 mm Table load in kG  2000 Kg Spindle Taper  Bt 50 kW power on spindle   15 kWS pindle speeds / ranges 6000 Rpm ATC tool changer  30 Coolant true spindle / Bar15 Bar Number off controlled axis3  

Qty. 1 Second-hand pub brewery Mfc.: EcoBrewtech Capacity: 15 hl Built: 1996 Consist of: 2 Vessel Brewhouse 3 x 15 HL fermenting tanks (w/ cooling jacket) 4 x 15 HL BBT (w/ cooling jacket) 4 x 15 HL BBT (PED) 1 water tanks 20 HL Steam generator (NEW): 106.4 kWn, 150 kg/h Steam, 5 bar ITWS (NEW): 25800 kcal Malt handling

Aluminum circular saw machine make KALTENBACH type SKL 450 NAYear of manufacture 2001Technical specifications:Saw blade diameter: 450 mmCutting speed stepless: 0 - 3000 mm / min.Rapid return: 4500 mm / min.Cutting range around 90 degree: 160 mm: square 90 degree: 145 mm: square 45 degree: 130 mm: flat 90 degree: 250 x 40 mm: flat 45 edree: 320 x 50 mmStroke length of the automatic feeder: 1000 mmMultiple stroke: 9999 mmSwivel range for multiple strokes: 180 degreeExternal dimensions approx .: 2700 x 1450 x 1900 mmWeight approx .: 1480 kgWorking height :: 1010 mmDrive power: 3.7 / 4.7 kWused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machi ...

Push-mast forklift, high-bay forklift used Manufacturer: STEINBOCK BOSS Type: WA15R-19130 MK II A-1 Built: 1999 Operating hours read: 10747 Callable capacity max 1000 kg Lifting height: 8750 mm Weight without battery: 6550 kg Battarie 80V 4 PzS 620 kW13/2019 Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

Aluminum automatic saw make ELUMATEC type SA 73/25Machine -No: 20124 built in 1990for mass cutting of aluminum profilesTechnical specifications:Saw blade diameter :380 mmSaw blade bore: 32 mmCutting area: 195 x 120 mmSaw blade speed: 3000 rpm.Pivoting range:90°Feed lengths:5 - 250 mmTable size: 200 x 600 mmVoltage: 220/380V 50HzPower output: 3 kwCompressed air connection: 7 barDimensions: 2700 x 1350 x 1470mmApprox. weight: 140 kgwith- Saw blade 370 mm- Micro spray device- pneumatic material clampingused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Gas Engine Generator Set (CHP/BHKW) MAN for natural gas Model E2866E 95 kWe Spec number 524806 Serial number 27093890484901 Stamford generator UC1274E2 400V/50Hz, 140 KVa 202 Amp year 2000 Serial number 0117910/02 Scope of delivery: - Generator set - Control panel

Aluminum circular saw machine make EISELESaw blade diameter :: 250 mmCutting area: 90 °: 45 °at Sägeblattdrm. 275 mm: 120 x 75 mm: 80 x 75 mmL-iron: 80 x 80 mm: 80 x 75 mmFlat iron: 120 x 75 mm: 80 x 75 mmSquare steel: 75 x 75 mm: 75 x 75 mmRound material: 90 mm: 90 mmSolid material round: 60 mmStandard saw blade: 275 x 2.0 x 40 mmDrive power:: 1 / 1.2 kWMachine head can be swiveled on both sides: 45-90-45-30 °Dimensions: 900 x 800 x 1100 mmWeight approx .: 230 kgused, from an operational resolutionin good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

properties: Used belt conveyor Condition: fully functional with traces of usage Ideal for fast material transport Expertly dismantled and packaged Condition: used Incl. SEW motor Technical Data: Dimensions of the gut conveyor Total length: 12,790 mm Total width incl. motor: 900 mm Total width without. Engine: 750 mm Belt width: 550 mm Condition: good (used) Belt type: Smooth Material: Steel Frame Height: 170mm Engine data: SEW r/min 125/254 kW0,66/13 belt conveyor The belt conveyor is ideal in the picking zone for interlocking machines or workstations and to optimize the internal process. During transport, the belt conveyor can transport sensitive and different sized containers, boxes or other packaging and article units to the feed-off or dispensing point and also serves, for example, as a connecting line in front of or between production and  ...

2 assembled aluminum circular saws make EISELE type LMS III PVMachine -No: 2224 + 2225 built in 1988xa0Technical specifications:Saw blade size: 400 x 4.0 x 40 mmCutting area 90 °: 500 x 140 mmhor. 45 ° L + R: 400 x 140 mmvertical 45 ° L: 500 x 90 mmVenetian blind box profile: 500 x 152 mm(with saw blade 410 mm)Saw blade speed: 2800 rpm.Drive power: 2.6 kWWeight per piece: 670 kgExternal dimensions per piece: 1800 x 800 x 1300 mmWith- hydr. stepless feed- Spraying device2 identical saws LMS III PV - mounted together on a base frame - for cutting larger widths and mitres 45 ° L and 45 ° R!The saws are sold together or single!If the saws are sold together, a designated cabinet is included.The saws come from a CNC controlled profiling machineThe technical. Data concerns 1 machine. When taken over and used in the now inflated state (both machines assembled opposite each other), the machi ...

Eccentric screw pump,stainless,acid-proof steel,Netzsch NL 40A,4 kW0,Theo. Cap. 0-10000 l/h

Miter and miter circular saw Fabr. ELU type TGS 172Machine -No: 2201 Year 1983Saw blade diameter: 250 mmSaw blade speed: 2600 rpm.Cutting area 90 °: 0 x 70 mm45 °: 0 x 38 mmPower connection: 220 V / 50 HzElectricity requirement: 1.1 kWDimensions: 700 x 650 x 850 mmWeight approx. 48 kgWith- Version rotatable as a cross-cut and table saw- tiltable and rotatable- Length stop 3.0 m- feet for machine and stop- Table longitudinal stop- Suction hoseused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Shredder | Cutting mill 18/45/ 7.5 kWt VGA for plastic 18/45 VGA Cutting mill for plastics, cable 7.5 KW, 80-140 kg/h. Model: VESPA 18/45 / 7.5 kWt VGA Throughput Kg/h: 80-140 Rotor diameter мм: 180 Rotor knife quantity/dimensions piece x mm: 6×225 Stator Knife Quantity/Dimensions Piece x mm: 4×225 Motor kW: 7.5 Weight Kg: 320 Capacity (cable) kg/h: up to 140 Capacity (plastic) kg/h: 80-120 Dimensions (mm) A 860 B-670 C-1480 D 1250 E 460 F 220

Aluminum circular saw Fabr. MEP type Cobra 350Fabr. -No: 021746 LRX year 1993Cutting area 0 ° round: 120 mmCutting area 0 ° square: 105 x 105 mmCutting area 0 ° flat: 180 x 70 mmCutting area 45 ° round: 120/110 mmCutting area 45 ° square: 100 x 100/95 x 95 mm mmCutting area 45 ° flat: 135 x 60 mmSaw blade speeds: 1700/3400 rpm.Vise opening: 180 mmDrive power: 1.5 / 2.2 kWWeight approx. 160 kgWith- 2 hours. pneum. tensioners- Underframeused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Filling station, bagging station for big bag, octabine with material conveying blower Big Bag filling station with conveyor blower for filling regrind or granules in Big Bag 1.5 m³ The Big Bag filling station is robust and easy to handle. The system is ideal for use where dry granules or regrind are to be filled into octabine or big bag. Compact versions have been developed for smaller containers such as small boxes and sacks. These filling stations are ideal for smaller granulators or insert mills to fill smaller quantities of regrind into small boxes or bags. With a sophisticated design and a wide range of combinable options, the filling station can be filled for various bulk materials. The frame and the entire construction is made of sturdy profiled steel materials. Material handling system | Filling station, emptying station for one or two big bag or octabin or for small ...

Cutting mill for high demands in a compact class. The mill is ideal for grinding small quantities. In production, there are always surpluses, missing parts. These recyclable materials can flow back into production, so that manufacturing costs can be optimized and reduced. Cutting mill, assistance mill VESPA 16/22/4 kWt for small parts Model VESPA 16/22 / 4 kWt VGA Throughput Kg/h: 40-60 Rotor diameter мм: 160 Rotor knife quantity/dimensions piece x mm: 6×110 Stator Knife Quantity/Dimensions Piece x mm: 4×110 Motor kW: 4 Weight Kg: 320

Underfloor circular saw for aluminum made by EMMEGI type 500 SCAMasch. -No: 191446, year of construction 1987Technical specifications:max saw blade diameter: 500 mmSpeed: 2890 rpm.Cutting capacity 90 ° e.g.: 170 x 150 mmor e.g.: 100 x 250 mmCutting area 45 ° e.g.: 170 x 165 mmor e.g.: 130 x 150 mmCutting area 20 ° e.g.: 150 x 60 mmor z. W .: 90 x 90 mmWeight approx: 520 kgDrive power: 4.0 kWWith- Minimum quantity spraying device- 2 vertical clamps- Miter cutting deviceused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Material conveyor belt LT-400 | Inclined conveyor belt for waste loading and material feeding for granulators and other applications. Movable, very stable design, height-adjustable at the outlet. Working width: 400 mm Working length: 3000 mm Working speed: 15 m/min. Maximum head: 1950 mm Gearbox: Bonfiglioli 0,55 kWt Weight: 250 kg