126,768 used machines on RESALE, but how to find them? Machine Search
for cellophanizing of chocolate boxes top condition Siemens PLC with 2 adjustable folding fittings 2 machines available, price is per piece
Y.O.M.: 1991 No.: 4745 2 hoppers, 1x with double jacket Scraper agitator speed-controlled Homogenizer speed-controlled Double jacket pressure-resistant Temperature controller, vacuum Condition: very good Dimensions LWH: 1100 x 600 x 950 mm Weight: approx. 300 kg
Roller spreader for rear mounting, drive via a 12 volt electric motor with overload protection (8 A). Container contents 120 ltr. , cam roller with interchangeable, asymetric cams (suitable for sand, salt and shards or granules)Roll width 125 cm, stirring shaft to prevent lump and bridge formation, low-wear 10-stage scattering volume regulation by adjustable spring bottom with rubber apron. With grating for accident protection and cable remote control (start/stop). Without growers! Scattering length salt approx. 5-6 km, sand approx. 1 km (manufacturer specifications) Built in 2012, unused, technically and visually as new condition, here and there paint somewhat repelled. Other roller spreaders, also trailers, self-loaders, drive hydraulic, PTO shaft or wheel stock. Winter service technology of all kinds, also slingshot spreaders, snow shields, snow blowers, tractors and used compon ...
Bone Band Saw KOLBE K330 Specifications: Type: Kolbe K 330 400 V / 50 Hz / 1.5 kW / 3.4 A / 16A CEE plug Max. cutting side passage: 260 mm Max. cutting height clearance: 310 mm Table dimensions: L59 x D76 cm Machine dimensions: H161 x W72 x D80 cm Saw blade size: 2490 x 16 mm Weight: approx. 155 kg Equipment: Device completely stainless steel Stainless steel base frame Work table can be folded out for easier cleaning (optional equipment!) Material pusher (removable) Side guide (removable) including 3 saw blades Left-hand delivery Protection Engine brake Function checked, machine immediately ready for use Stock machine, immediately available! Condition & accessories see original pictures. If you have any questions, email or call. 03423-706493
We sell the Kaeser SK 25 screw compressor, as a set including compressed air tank and refrigerant dryer The condition of the compressor can be seen in the attached pictures. The unit has been well maintained and is fully functional. Operating hours: 12,324h run and 2,317h load Last inspection 09/22. Until next inspection 1,029h load Technical details: -Operational -Fully automatic - Very soundproofed - Vibration damped - All panels powder-coated - For ambient temperatures up to +45 °C - Easy access to all service points thanks to removable left cover SIGMA CONTROL 2 Specifications: - Working pressure: 7.5 bar - Flow rate: 2.50m³/min - Maximum operating pressure: 8 bar -Rated power: 15.0 kW -Engine speed: 2960 rpm -Ambient temperature: 3 °C to 45 °C
No.: 851275 with speed-controlled feed pump Funnel in Exx protection with switchgear good condition Dimensions LWH: 700 x 700 x 700 mm Weight: approx. 100 kg
Massive aluminium die-cast base Engine S1: 1800W Weight: 23kg HM Circular Saw Blade D: 305mm Idle speed 4200 rpm Swivel -45/+45° extendable back stop Quiet Belt narrow laser stroke marks exactly the cutting line Deep stop G&HM-KAP-305JL
1 of used film-only multi-packer, make KHS, type Innopack Kisters SP 050 B2, new 2013. Operating side: links. Used for PET bottles 250/500 ml as 3x2=6-packs (dual lane) and 6x2=12-packs as well as 6x4=24-packs (single lane) in clear or print-registered film. Quick change-over via servos and spindles. Capacity upto 50 cycles per minute. Siemens S7 controls.
Cable length meter, -robust machine version, measuring wheel circumference 500, -with mech. Counter for 9999.99 m. measuring accuracy of 0.4%. -Number height 7. -Cable diameter 20-120mm Nudlmuhk With the electronic pre-selection counter as an accessory, the desired cable length can be preselected and the winding machine can be switched off. This machine does not have an official calibration.
running direction: right - left for 28 mm VacuVent closure with safety housing
Supply air heating system, NW250, 400V, 9KW, KMS, mint condition -80% Special price ! The current new price of a similar product is more than € 8,000 excluding VAT. If you have a VAT number, we will be happy to issue you with an invoice without VAT. Top condition like a demonstration unit! The part was removed from a new machine that has demonstrably only run for approx. 100 operating hours. Technical data: - Supply air heater 9 KW - Heating cartridge with heating cross 400V 3x3000W - Incl. pipework, complete design in stainless steel + pipe insulation - Incl. corrugated flex sleeves - Stainless steel intermediate non-return valve AWS ZRK-VA-VA-200-F - Assembled incl. stainless steel mounting bracket - Price is without HEPA filter and Ex centrifugal fan, we are happy to offer - Parts list and drawing from KMS - Inlet side NW250 - Outlet side NW250 reduce ...
KLÖCKNER MEDISEAL BLISTER PACKING MACHINE, MODEL CP200 Year of construction: 2018 Very compact machine of balcony construction with minimum space requirements and an output of up to 300 blisters per minute; format change over time of less than 30 minutes. Specially developed for efficient packaging of smaller lot sizes and clinical trials. Balcony construction Roller sealing Full set of manuals Machine previously used in the Pharma industry and is in like new condition, it has been deep cleaned with cleanliness certificates available on request. Water chiller KB56 and extraction unit available on request at additional cost. Output of up to 300 blisters per minute (dependent on product, material, and blister size) Power supply: 230/400V, 3 phase, 50 Hertz, neutral conductor FORMAT RANGE (1 LANE) Draw-off length forming: 170mm Draw-off length punch: 110mm Web ...
-suitable for Diosna Wendelkneter W 240 A boiler -Table lift tipper -Boiler pliers lock -with friction wheel drive and boiler shearer -mobile
used vertical hydraulic internal clearing machine with 3 clearing points in very good condition Pulling power:8.000 KG Clearance length: 1000mm Bgno2qtoyx Clearing: 3 pieces (4 pieces) Distance between clearing points:100mm Mounting diameter of the drawing heads3 x x 85mm Workpiece diameter: max. 1x 460mm / 2x 198mm / 3x 98mm Cutting speed: hydraulically infinitely adjustable from 1m/min up to max. 7m/min Return speed: hydraulically infinitely adjustable from 5 to max. 25m/min Space requirement of the machine (b x t x h) approx.:1400 x 2000x 3600mm (without service & operator environment) Power supply / connection value: 380Volt 50 HZ / 6.5 KW Accessories / Optional equipment: -manual and automatic clearing operation - Drawbridge for 3 clearing points - Workpiece table for 4 clearing points (only usable with special pullheads) - automatic tool feeder - tension dis ...
Kölle Band Saw BSM40 - With belt sanding and welding machine Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.
Machine No.: 2009.14 Power: 5.5 kW Pharmaceutical version as good as new Stainless steel with funnel (approx. 60 l) Switchgear EEx various spare parts, new cross-toothed grinding set LWH: 800 x 700 x 1400 mm Weight: approx. 120 kg
Rotary board cutter & creaser & half cutting Krause Model J138-LV/80 Year 1980's Creasing length 1300 mm 1st "station" 6 sets of half cutting tools 2nd "station" 7 sets of creasing tools to make a W shape 3rd "station" 7 sets of circular knives Table with side alignment & with push system Speed controlled by means of a spead pulley
Key data: 1 mm, 6300 mm
LHS Lagertechnik, supplier of shelving systems and general storage technology. Due to a customer's production closure, we are selling a KASTO HBA 420 band saw. In this ad, you will buy as follows: - 1 piece KASTO band saw HBA 420 - Year of construction: 1990 - Serial number: 17809 - Belt length: 6,300 mm - Band height: 41 mm - Band thickness: 1.3 mm -Conveyor - Connection voltage: 400 volts - Sale in as-is condition without guarantee and warranty - Loading with forklift, shipping and self-collection possible Sale in as-is condition without guarantee and warranty. Loading by forklift, shipping and self-collection possible.
Kalmeijer pastry moulding machine KGM Table Model Pastry moulding machine Kalmeijer KGM with 10 plates and 2 moulding rollers. Pastry moulding machine is suitable for the production of mürbeteigen. With different moulding rollers, the pastry can be moulded into the desired (depending on the mould ingeu) roll. The dough feed and the moulding roller are neatly removable to clean them. The moulding roller can be heated by means of heating. Sheet metal feeder is automatic, the machine stops when there is no sheet metal on the trensport plate. Machine is compact and easy to use. Kalmeijer pastry moulding machine with 1 moulding rollers with 10 black baking sheets Table equipment with heating automatic sheet metal feeder thick of the dough figures is adjustable Dough hopper, moulding roller, dough feed roller is easily removable for cleaning Easy to use The trasnport beams for ...
Grease separator sether boiler, Type: Easy Clean Standard NS 4B completely cleaned and rinsed, grease-free and odourless. leakage test. A spout pump is included in the scope of delivery. New price was 8000,00â?¬ net. Deutschaland-wide shipping in German-speaking countries possible at an additional cost. Delivery: - Boiler grease separator Easy Clean Standard NS 4B - Sampling device DN100/150 horizontal - Spühl pump for grease separators
2x KUMERA GEARBOXES COUPLED WITH SCANPUMPS GEARBOX RATIO 1.25:1 PUMPS 1800 RPM / 1642 M3/H
bizhub C227 = Equipment number: 1823718979 – Color MFP Incl. DF-628 Original Feeder, DK-514x Base Cabinet bizhub C227 Communication center with 22 ppm in b/w and color, standard Emperon pressure controller with PCL6 (XL 3.0), PCL5c, PostScript 3, PDF 1.4, XPS and OOXML support, paper capacities of 2 x 500 Sheet and 100 sheets from stacking sheet feeder, formats from A6 to A3, grammages from 60–256 g/m2, 2 GB Storage, 320 GB hard drive and 1 GB Ethernet as standard OC-514 Original Cover Cover instead of an Original Feeder DF-628 Original Feeder Automatic document feeder for up to 100 originals, with duplex function PC-114 Universal Cartridge A5-A3, 1 x 500 sheets, 60-256 g/m2 PC-214 Universal Cartridge A5-A3, 2 x 500 sheets, 60-256 g/m2 PC-414 Large Capacity Cartridge A4, 2,500 sheets, 60-256 g/m2 DK-514 Base cabinet Storage space for paper supplies and cons ...
bizhub C3100P = Equipment number: 1823718649 – Colour printer without additional accessories bizhub C3100P A4 printer with 31 ppm B/W and color. Standard Emperon™ Pressure Controller PCL, PostScript and optional XPS support. Paper capacity of 250 sheets and 100-sheet stacking sheet feeder. Standard duplex unit. 1 GB memory and Gigabit Ethernet standard. PF-14 Paper tray A4; 500 sheets; up to 90 g/m2 SCD-25 Base cabinet storage space for consumables HD-P06 Hard Drive1 320 GB Hard Drive 1 GB memory expansion 1 GB memory expansion for faster processes ID Card Reader1 Various ID Card Technologies LK-106 Barcode Fonts1 Printing Barcode Fonts LK-107 Unicode Fonts1 Printing Unicode Fonts LK-108 OCR A and B Fonts1 Printing OCR (A and B) Fonts LK-111 ThinPrint® Client Native ThinPrint Client SX-BR-4600 Wireless LAN Wireless LAN to Network Connection EH-C591 Staple Unit Sta ...
PET stretch blower, incl. Preform silo, conveyor, sorter and feed, up to 6000 bottles/hour, 6 stations, 0.2 - 3.0 litre, technically / optically good condition. Available at an additional cost: compressor system, mould cooler and moulds.
PET plug-in / blow era 10 blowing stations, capacity: approx. 8,000 - up to 10,000 bottles / hrs. Volume: 0.2 - 3.0 litre, incl. preform silo and steep conveyor and feeder.
Shelf-mounted robot KUKA KR16 KS KRC2ed05 Bj.2006 Euromap 67 Extension does not exist in the picture Control: KRC2ed05 Number of axes: 6 Max. load capacity: 16 kg Max. working range: approx.:1800 mm Year of Make: 2006 Scope of delivery: robot, controller, cable, teaching panel, circuit diagrams. 2 weeks commissioning warranty. No further warranty. In addition, spare parts are always available from stock. Robot is fully functional and can be viewed Auction amount is ex-works. Freely loaded. You will receive a proper invoice with VAT. Further questions will be answered by e-mail or phone. The amount indicated is net. The statutory VAT of 19% will be added at checkout. You will receive a proper invoice with VAT.
PVC - heating / cooling mixing combination Hot mixer 750 ltr. / Cooling mixer 2,500 l. Engine power: 212 + 45 kW
Head machine Kemper Soft Star -6 in a row -with plastic dough hopper -with Siemens Touch Panel control -Built 09/2007
Grease baking device Roka plant Tippfix Model DA 900 -14.4 kW -Outside mass: 80x204cm -Basin indoor mass: 70x194cm
Longitudinal Splicer Manufactured by KUPER Model: FL/I-1000 - FL/INNOVATION
Working Width: 800 mm Working Height: 300 mm Main Motor Power: 250 KW
Longitudinal Splicer Manufactured by Kuper Model: FL/Rapid
Type: Quadro Relax S Built in 2012 with lifting tipper HK200 Manufacturer: WP Kemper Built: 2012 State: Used
Bearing number: 3488 Profile steel shears Manufacturer: Mubea, Type: KBLH 500 Machines NR.: 0156085927332, Year of construction: 0 Specifications: Size Printl 50 To Max punching dia 30 x 15 mm mm Stroke length 0-60 mm Number of strokes per min. 16 Extension 410 mm Flat steel 180 x 20 - 400 x 10 mm Angular steel 50 mm Round steel 55 mm Total power 7.5 kW Hydraulic. Length: 1400 mm, Height: 1800 mm, Width: 800 mm, Weight: 1800 kg
Key Vibratory conveyor Stainless vibratory conveyor, internal dimensions 1800mm x 650mm, hopper height 1550mm, discharge height 850mm, 3Ph
ZIM Hülsta Carcase Erector The carcass erector is used for erecting and transporting assembled carcasses. Carcase erectors are usually used for carcass presses with a continuous device. It facilitates handling when setting up large workpieces. Transport and assembly device within a corpus assembly line. Behind a continuous carcass press, the pressed carcasses are placed on the back with the help of this device. Assembly work on the underside can thus be carried out. Make: ZIM Hülsta-Werke Type: Carcase erector Metrics: More items - new and used - can be found in our shop! International shipping costs on request!
Ladies and gentlemen, we have and now available used transformer stations Built: 2000 Power: 1000KVA Primary voltage: 20kV Secondary voltage: 690V, Switching group: DYN5 Switchgear: SF6 Immediately ready for use and available, nationwide good delivery. If you have any further questions, Mr. Serhan is here for you, available Monday to Saturday from 8 a.m. to 10 p.m. and 24 hours in case of emergency
Kreuter Chocolate temperer Model: TMK100 Serial: 7906/91 Refurbished by Wolf in 2013, 100Kg chocolate temperer, adjustable temp controls, agitation with scrape surface, with all manuals, 3Ph
Bone Band Saw KOLBE K260 Specifications: Type: Kolbe K 260 400 V / 50 Hz / 1.1 kW / 3.1 A Year of manufacture: 2018 Cut side passage max.: 215 mm Max. cutting height clearance: 250 mm Table dimensions: L46 x D70 cm Machine dimensions: H160 x W60 x D70 cm Saw blade size: 2170 x 16 mm Weight: approx. 115 kg Equipment: Device completely stainless steel Stainless steel base frame on 2 swivel castors with brake & 2 fixed castors Work table can be folded out for easier cleaning (optional equipment!) Material pusher (removable) Side guide (removable) Left-hand delivery Protection Engine brake Function checked, machine immediately ready for use Stock machine, immediately available! Condition & accessories see original pictures. If you have any questions, email or call. 03423-706493
Dopel membrane pump 1 inch with suspended solid pre-separator Pneumatically operated, mounted on transport trolleys on a mobile-by-mobile vehicle. Technical data: Gear ratio: 1:1 Maximum capacity: approx. 197.6 l/min Discharge quantity per cycle: approx. 0.88 l Air connection: 1/2" Nominal suction side: 1" Nominal diameter print page: 1" Maximum operating pressure: 8.3 bar Max solid diameter: 3.3mm Weight: approx.10 kg Lukra pumps, basement pumps Special price
compressors / vacuumpumps Flowservice Sihi type KPHY-80540BNX6Y TB4 101 914 12, year 2016 and 2018, suitable for hot air and gas, with motor 90 kW, 985 tpm Price on request
automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 Machine was only in operation for 4 years specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 42 t Attached pictures are only sample pictures!
Insulating container 600400 . Batteries available
electrically operated chamber furnace with air circulation , as good as new electric heated chamber furnace with air circulation, as good as new Type: EKO - 60/40/150-36 Year built/year: 2010 Fabr./ make: IOB Aue/ Germany Working space/ inner space 600 x 1500 x 410 mm Temperature range/ range of temperature: 500°C Connection value Electr./ electr.power: 38 kW Weight / weight: about 2.5t https://www.west-cs.de/produkte/modelle/ks-90-1-einkreisregler/
Machine type: Automatic band saw - Horizontal Manufacturer KASTO Type KastoTwin A4 Year of construction 2002 Country of origin Germany Delivery time by arrangement Freight base from location Technical details Cutting diameter 400mm Saw blade length 5,090mm Cutting width 1.3mm Cutting range at 90 degrees: around 400mm Cutting area at 90 degrees: square 400 x 400mm Smallest diameter 10mm Smallest section length 6mm Feed length 750mm Cutting speed 20 - 110m/min Clamping pressure 20 - 60bar Saw blade dimensions 5,090 x 41 x 1.3mm Total power requirement 7.0kW Machine weight approx. 1850 kg Space requirements approx. 2400 x 2500 x 1700mm
KUKA KR 150-2-TJ industrial robot was manufactured in 2001 in Germany by KUKA AG. This multifunctional machine is the ideal solution for automating industrial processes that require precise and reliable operation. Using the DeviceNet network protocol, it is possible to connect and configure the robot with any device, such as a conveyor gripper, welding head or plasma torch. Over the past few years, the KR 150/2 robot arm has undergone a full service and has been comprehensively prepared for operation. Some of the many overhaul works included a performance test of the inverters and motors, checking and adjusting the robot's gears, as well as replacing the batteries and the input/output module (Balluff) in the controller. Technical specifications of the KUKA KR 150-2-TJ robot - number of axes: 6 - 7-axis, 8-metre long track - controller: KUKA VKR C2 - portable teach pendant: KUKA ...
maximum number of results exceeded
please refine your search
