jig grinding used for sale

Double-sided grinding and polishing bench MEYER type SMPMasch. No. 848 Year of construction 1963Shaft diameter 50 mmGrinding wheel holder 305 mmDisc spacing 1470 mmGrinding-polishing wheel diameter max. 800 mmWorking height 550 mmSpeed 710 / 800 / 950 rpm. Drive power 2x 3 kWNet connection 380 volts, 50 Hz.- two drive motors for each working side separately- star-delta switch for each drive motor separately- speed change by folding the drive belt- dust extraction flange 100 mm-

The machine underwent a general overhaul in 2015 The following tasks were performed as part of the overhaul: repair of the electrical cabinet and hydraulics, scraping of the bed and table, replacement of bearings in the headstock, new springs for the axial bearings, new table piston rod and sleeves, installation of sludge separators. Documentation for the machine is available. Year of manufacture: 1980.

GENERAL Project No.: 905789 Quantity: 1 pcs. Manufacturer: BUDERUS Type: BDG 220 Control: Siemens 840 D solutionline Year of Make: 2020 Condition: Used machine Spindle Approx (hrs): 3000 Shifts machine one approx. (hour): rarely used DESCRIPTION GRINDING Max. workpiece diameter 440 mm Max. workpiece height 150 mm Travel in X 170 mm Max. rapid traverse speed in X/Z 30 m/min Max. feed speed in X 0.01-15 mm/min Max. speed workpiece spindle 1000 1/min OTHER EQUIPMENT Workpiece probes for measuring thickness deviation Gate sensor Splash protection cladding with fully encapsulated working area Automatic work room door Lighting in the work area Mechanical oil/emulsion mist extraction system Coolant device with paper belt filter High pressure pump 25 bar Mobile control unit for set-up operation with electronic handwheel Machine condition light Au ...

Very good surface grinding machine Table surface / working area 200 x 600 mm

Unused alubit grinding balls (alumina ceramic) designed for wet grinding (continuous operation), available in the following sizes and quantities: 1 1/4'' (32 mm) [1,000 kg]; 1 1/2'' (38 mm) [990 kg]; 2'' (50 mm) [700 kg]; 1 3/4'' (45 mm) [940 kg]; 2 1/2'' (64 mm) [1,970 kg]. All balls made in Italy, packed in 25 kg bags.

Unused alubit grinding balls (alumina ceramic) designed for dry grinding (batch and continuous operation), available in the following sizes and quantities: 1 1/4'' (32 mm) [960 kg]; 1 3/4'' (45 mm) [1,580 kg]; 1 1/2'' (38 mm) [940 kg]; 2'' (50 mm) [410 kg]; 2 1/2'' (64 mm) [580 kg]. All balls made in Italy, packed in 25 kg bags.

CNC cylindrical grinding machine, (carousel) for internal, external and surface grinding. A lot of accessories, such as grinding wheels of different types and sizes. Retrofitted 2007 . Magnetic clamping plate dia 1500mm, Circumferential diameter 1800mm, Largest grinding diameter 1600mm Maximum grinding height 880mm Max. workpiece weight 5to Swivel angle of the grinding spindle: 90° left, 60° right

ELB ELB Super Rubin 020 VA II CNC surface grinder High-precision horizontal surface grinder, specialized for profile punches grinding. With 4 added digital axes CNC Control Wireless Handwheel Bluetooth control Magnetic Table 600 x 300 mm Movements axis X/Y/Z: 650/300/250 mm 4th axis- rotational Grinding wheel: -Dia 300 mm -width 40-50 mm -bore size 76,2 mm Spindle speed 1400-2800 rpm Total power requirement 5,5 kW Weight of the machine ca. 3,4 t 4th axis devices: -Punch former PF350 V-block -Punch former PF650-ER20 -Punch former PFD-ER40 -Punch grinder PGAS- centreless Accessories: Collets Radius and angle dresser RDC Sinusoidal-table for devices SPF 50 Balancing rack for wheels LBS 14 surface grinder High-precision horizontal surface grinder, specialized for profile punches grinding. With 4 added digital axes CNC Control Wireless Handwheel Bluetooth c ...

Grinding wheel holder Klingelnberg (627.020.006) Outer diameter Ø 260 mm / inner diameter Ø 56 mm - Incl. grinding wheel of Carborundum dilumit Outer diameter Ø 480 see pictures technical drawing Auction-ID: A1-47017-66

Grinding wheel Max. 2620 . T/M Profile 240x16x45 Auction-ID: A1-47017-83

Grinding wheel holder Klingelnberg (627.020.006) Outer diameter Ø 260 mm / inner diameter Ø 56 mm - Incl. grinding wheel Outer diameter Ø 400 see pictures technical drawing Auction-ID: A1-47017-68

Grinding wheel holder Klingelnberg (627.020.006) Outer diameter Ø 260 mm / inner diameter Ø 56 mm - Incl. grinding wheel of Carborundum dilumit Outer diameter Ø 400 see pictures technical drawing Auction-ID: A1-47017-65

Grinding wheel holder Klingelnberg (627.020.006) Outer diameter Ø 260 mm / inner diameter Ø 56 mm - Incl. grinding wheel Outer diameter Ø 400 see pictures technical drawing Year of construction unknown Auction-ID: A1-47017-67

Grinding body dimension: 200 x 40 x 76 mm Circumference speed: 30 m / sec Follow-up value: 0.7 kW Weight: approx. 250 kg Specification: Double grinding bracket with integrated suction

Water-cooled grinding spindle motor for JUNKER Quickpiont 13.5 kW ,380/660 V ,25/14.5 A ,2940 rpm ,50 HZ

Fabric grinding belts of M3 1260 mm x 13 mm P150 for metalworking

; NEW

Tip height 120 mm, grinding length 1000 mm, 8 spindle speeds 55 - 600 rpm, spindle head holder MK 3, table sash. infinitely adjustable, table swivel 7 each, delivery by hand or automatically, grinding wheel-dm. max 400 mm, Grinding wheel width approx. 60 mm, tailstock holder MK 2, connection value approx. 3.5 kW, automatic working cycle, express speed 30 mm, automatic. Piercing loops. The machine is functional and does not require a geometric revision. Accessories on request!

universal tool sanding machine manufacturer fa Kellenberger (Strausak) the machine is geometrical and also funktionmig in a very good state. Spitzenh?he: 125 mms top width: 680 mms L?ngsbewegung: 500 mms Arbeitsfl?che of the table: 1030 x 214 mms Q?rzustellung: 280 mms mm H?henverstellung Schleifkopf:300 wheel area Schleiftisch: + 90 °/-45 ° wheel area Schleifkopf: 350 ° Horizontally wheel area Schleifkopf: 360 ° Vertically Schleifspindel 4 speeds: 2250-3000-4500-6000 revos Schleifscheibendurchme?er: 250 mms Antriebsleistung:Schleifsp .: 1.5 kW Sony 2-axes digital display 0,001 mms

a palette with 145 kg - 4 pieces new Schleifscheiben D=350mm, 2 pieces used Schleifscheiben with flange, 10x Abrichtrollen. a palette with 319 kg - 4 pieces Schleifscheiben D=400mm uses with flange and an Abrichtrolle.eine palette with 257 kg - 22 pieces Abrichtrollen with flange

Machine number: 3728-87 Grinding length 2000 mm (Roll grinding machine)

Working diameter: 40 - 250 mm Automatic work piece loading and removing for ball diameters: 40 - 105 mm Manual loading for diameters: 105 - 170 mm Direct ball attaching: 170 - 250 mm Rotation speed, stepless: 10 - 300 rpm Grinding spindle speed range: -160 - 3150 rpm -80 - 1580 rpm -38 - 775 rpm -20 - 385 rpm Weight: 6,5 tn Electrical connection: 17 kW Year of manufacturing: 1991

Offer via gebr. flexible shaft grinding machine SUHNER type Rotomax 3.5   - Lightweight and compact design - Stable high-performance motor and infinitely variable torque adjustment - Wide range of shafts and tools - Control from the handpiece by optional manual shutdown   Three-phase motor for 3-phase alternating current Protection class IP 44 Overload Power consumption 3.5 kW Voltage 400 V, 50 Hz Idle speeds Connection DIN 15: 500-10,000 min-1 Anschluss ‪DIN 10‬: 500–25.000 min–1 Speeds infinitely adjustable Mobile   Applications: Grinding, cutting, roughing, rusting, polishing, brushes, etc. For heavy work in foundries, in boiler and steel construction, in mechanical Workshops, stainless steel processing plants

ė engine capacity exceeding 1.1 kW (900 RPM). 310 x 250 mm grinding shaft. 2 clamping ė velen styles (the rubber surface), diameter 30 mm. the preparation of Į (i) the measurements x 350 x 655 mm, 505. the preparation of Į weight 20 kg.

Belt/ozilierend swiveling Roll in the table

specifications: - Load capacity positioning base approx. 750 kg - Flatplate diameter 500 mm - max. workpiece diameter 1600 mm - Height turntable with horizontal position approx. 750mm - Turntable with right,- + left run - Axis of rotation turntable endless 360 ° - Rotation time per revolution 12.5 sec. - Pan left + right - Swivel axis rotation angle 180 ° - Swivel time for 180° swivel angle 10 sec. - 2 x double foot button for turntable + swivel arm - hydr. Clamping bolt for clamping the workpiece in the middle of the turntable - Clamping stroke / clamping distance of the clamping bolt 32 mm - Clamping force pressing / pulling 80 / 48.9 kN - Clamping cylinder female thread M 27 x 40 - Positioning control SIEMENS - Operation manually or via control - Space required approx. W 1500 x D 2800 x H 1100 mm - Weight approx. 2500 kg - separa ...

Kellenberger: 1000 U 125 Machine was totally dismantled and rebuilt from the ground up. All sheet metal and aluminum parts are laminated. Work piece headstock newly stored. Completely overhauled hydraulic, All filter replaced.

width of the strips: 75 mm band length: 2000 mm band speed: 33 m/s weight of the machine ca.: 90 kg Power: 3 KW 400V / 50Hz Volume: 83 dB The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Technical data: with stand, 50 Hz, DAB ED 25% Engine: 3 Capacity: 1.75 A Capacity: 736 W Voltage: 380 V

Grinding wheel flange for Kellenberger / Strausak u.-Miwatec grinding machines type 57 U / W in special design. Questions us please at we do extensive accessories for these machine types.

Grinding wheels recording for Kellenberger / Strausak u.-Miwatec grinders. Grinding wheel holder for 76 mm bore. More technical info. on request.

grinding band dimension: 75 x 2000 mm band speed: 33 m/sec weight of the machine ca.: 90 kg engine output: 4 kW turning speeds: 2800 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Grinding wheels recording for Kellenberger / Strausak u.-Miwatec grinders. Wheels shot 38 mm. For more details please call us. We carry special accessories in our program. We repair and repaired on the spot and make complete engine overhauls Special grinding machines

Accessories fur WU 3 ms, apparatus of part of, round loop facility, etc. More info on request

Discus Werke DSH 600/1000 Side Surface Grinding Machine This type of machine is a machine with a motor-driven grinding spindle. The clamping and grinding of the workpieces is carried out with clamping devices tailored to the respective work. The devices are attached to the machine bed. The column saddle on which the motor spindle is mounted serves as a feed, dressing and pendulum slide. Manufacturer: Diskus Werke Model: DSH 600/1000 Serial number: 6299 Type: Side Surface Grinding Machine Cooling lubricant: Isocool 1020 BF Coolant volume: 400 liters Concentration: 2.5% (x factor 1.6 ≙ 4%) Year of construction: 1964 Condition: used The side surface grinding machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure,  ...

Reduction sleeves for work piece headstock recording MK 5 Reduction MK 5 / MK 1 MK 5 / MK 2 MK 5 / MK 3 MK 5 / MK 4 Reduction sleeves with forcing nut. Price indication per piece. We carry new & - used Center points in special dimensions.

Special price for stock goods! Only while stocks last! Belt dimensions: 75 x 2000 mm Belt speed: 29 m/sec. Contact disc Ø x W: 200 / 80 mm Face grinding table: 460 x 75 mm Suction connection Ø: 100 mm Motor output power S1 100%: 3.0 kW Motor input power S6 40%: 4.0 kW Voltage: 400 V Length: 1080 mm Width: 440 mm Height: 1000 mm Weight approx.: 66 kg Characteristics: - Good grinding performance due to high belt speed - Quick adjustment for horizontal and inclined position - Continuous face grinding surface for optimal grinding of long workpieces - Constant belt tension due to spring-loaded clamping device - Universally applicable for grinding edges, surfaces and cylindrical grinding - Including quick clamping system for fast belt changes - Easy adjustment of the parallel belt run by means of adjustment screw - Graphite coating on the face grinding surface increa ...

We give our wheel bearing. Vitrified bonded grinding wheels for metal processing. From 100 mm to 600 mm in diameter. We carry also diamond and CBN wheels for tool grinding machines new and used. Strausak Fleximat 91 we have yet complete disc sets for all common diameters for the machining of solid carbide and HSS milling and drilling tools. Price and info. on request.

Small 4-side brushing/grinding machine for small parts. Minimum part length 250 m ! SPECIFICATIONS: Feed belt speed: 3-20 m/min. Spindle diameter: ø 40 mm Length of horizontal spindle shaft: 150 mm Length of vertical spindle shaft: 100 mm Maximum brush diameter: ø 200 mm Spindle speed as standard: 1000 ot/min (possibility of infinitely variable control) Power of the main motors as standard: 4x1.1 kW Power of the motor for the feed of the conveyor belt: 0.55 kW Diameter of the suction nozzle: 2 x ø 120 mm Maximum material height: 100 mm Maximum material width: 150 mm Minimum length: 250 mm (must be advised) Weight of the machine: 450 kg Compact machine with quick adjustment and optional parameters. KuSING has been manufacturing woodworking machines since 1991. In the field of 4-sided brushes, we offer a wide range of machines for every application. Parameter chang ...

We give our wheel bearing. Ceramic grinding wheels of different binding and hardness. Dimensions von75 mm to 600 mm. The discs are new, unused, and undamaged. Retail possible, price on request.

Band dimensions: 150 x 2000 mm speed: 14.5 / 29 m / sec. Contact plate: 200 mm / 155 mm plan grinding table diameter: 460 x 150 mm Extractor connection: 100 mm in diameter engine power: 4 kW

We have a very wide range of accessories for Kellenberger - Santiago &-Miwatecmaschinen. Grinding wheel flanges new u. - used. Chuck flange recordings MK 5 SK 50 for magnetic Chuck, three & four-jaw Chuck. Running with Center points, and fixed. Three-jaw four-jaw &-special Chuck. Magnetic clamping plates, cross - ring - Sternpolteileung. Truing devices, RADIUS &-inclined dressing Lynetten 2 & 3 jaw

STANKOIMPORT 5822M thread grinding machine was manufactured in the USSR. The machine is used for the process of grinding threads to give them the correct dimensions and roughness. During this process, a grinding wheel with a diameter of 400 mm is used to remove a small allowance from the workpiece, forming the thread shape on it. The grinding machine processes threads with a maximum diameter of 200 mm, a length of 500 mm and a weight of up to 30 kg. Depending on the choiceed disc, the diameter of the workpiece can be from 3 to 150 mm (grinding with a single-coil disc) or from 10 to 120 mm (grinding with a multi-coil disc). The total weight of the grinding machine is approximately 5 tons. Technical data of the STANKOIMPORT 5822M thread grinding machine - maximum workpiece diameter: 200 mm - diameter of the workpiece grinded with single-coil disc: 3-150 mm - diameter of the workpi ...