index v used for sale

This 5-axis Hamuel Reichenbacher Vision Flex was manufactured in 2021. It features an impressive X-axis travel of 8,060 mm, Y-axis travel of 1,210 mm, and Z-axis travel of 760 mm. The machine is equipped with a spindle speed of up to 24,000 rpm and a 20-station automatic tool changer. If you are looking to get high-quality machining capabilities, consider the Hamuel Reichenbacher Vision Flex vertical machining centre we have for sale. Contact us for further details.

CONTROLS   CNC controls SIEMENS BASIC FUNCTIONS   number of spindles: 2   number of turrets: 1   number of c-axes: 2 WORKING RANGE TURNING   turning diameter (max): 100 mm   worpiece length max.: 150 mm MAIN SPINDLE   spindle revolutions (max): 6000 /min TOOL MAGAZINE   number of positions: 12 ELECTRICAL SPECIFICATIONS   total power consumption: 36 kW   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   total weight approx.: 7000 kg ATTACHMENTS (TURNING)   hydraulic system: yes   European CE standards: yes Machines in good condition: - Integrated pick-up automation - Two EMAG machines configured in a line are for sale. - A robot destacking unit with 100% parts inspection can also be purchased.

Ulma VTI 640 Technical Specifications Model: VTI 640 Condition: Mint (fully functional) Year of Make: 2025 Capacity: Up to 20 packs/minute (depending on film and product characteristics). Packaging Type: Flowpack Features ✅ Wash Down IP 66 version in hygiene design ✅ Machine suitable for laminated film ✅ Machine prepared for MAP ✅ Format tube for bag width 300mm ❌ Label dispenser ✅Videojet 6330 Printer ✅ Signal for printers / labellers ❌ Double film roll holder ✅ Automatic foil centering ✅ Quick-change system for film with vacuum gluing table and knife ✅ Ejector sponge for controlling package volume ✅ Synchronization signals for pre- and trailing devices ✅ Discharge belt increasing ✅ Volume pneumatic filler with tank 200 – 300 litres Documentation & Operation Language (documentation & HMI): German (other languages on request)  ...

Leybold Vacuum Casting Resin System VGH 1000 Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Viewing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.

Used OCME VEGA HT 100-2 shrink wrapperTechnical Specifications & Performance DataThe Ocme VEGA HT 100/2 is a shrink wrapper designed for film bundling of cans in industrial packaging and beverage production environments. The machine handles a current 330 ml format and forms film packs using a two-reel configuration. Its stated maximum performance is 100 × 2 ppm, supporting high-output secondary packaging operations.Manufacturer: OcmeModel: VEGA HT 100/2Maximum speed: 100 × 2 ppmContainer type: Aluminum cansCurrent format: 330 ml (3x2) configuration Package configuration: Film packNumber of lanes: 6Number of film reels: 2Maximum reel diameter: Ø 500 mmMaximum container height: 250 mmMachine pitch: 380 mmWorking plane height: 1250 mmPower supply: 400VInstalled power: 210KWOperating pressure: 6 barAdvanced Automation & Control SystemsThis shrink wrapper is equipped with Siemens HMI and S ...

For sale is a used AXA VSC-1-M C machining center, manufactured in 1999 and equipped with a HEIDENHAIN TNC 430 PA Controller. This machine offers a generous table dimensions mm of â2.200x500 and an X-axis travel mm of 2.240 / 2x 700. The Y-axis travel mm is 420, while the Z-axis travel mm reaches 480. It features a spindle speed range from 60 to 6.000 rpm with an SK 40 DIN 69871 A Spindle taper / interface. The system includes 20 bar Coolant through spindle bar and a Tool magazine capacity of 22.

Used Tetra Pak TBA8 1000ml square V110, Helicap 27Technical Specifications & Performance DataThis used bottling line is configured around a Tetra Pak TBA 8 V110 filling machine for square 1.0L Brik carton packs. Manufactured approximately in 2001, the filling machine has approximately 26,000 working hours and received a total refurbishment in 2026. The line includes dedicated screw-cap application, wrap-around tray packing and interconnecting conveyor equipment for an integrated carton packaging process.Filling machine: Tetra Pak TBA 8 V110Pack format: square Brik carton, 1.0LYear of manufacture: approximately 2001Working hours: approximately 26,000 hRefurbishment: total refurbishment in 2026Conveyors: approximately 30 metres, according to the standard layoutAdvanced Automation & Control SystemsThe line combines filling, cap application, conveying and tray packing into a coordinated indu ...

turning diameter: 1000 mm swing dia.: 1000 mm Z-axis stroke: 900 mm control: Siemens 840 D tool taper: SK 50, VDI 60 tool piece magazine with: 44 Plätzen workpiece weight max.: 35 kg tool length - max.: 500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Mazak VTC 800/30SR CNC Bearbeitungszentrum (2009) Hersteller: Mazak Typ:VTC 800/30SR CNC Bearbeitungszentrum Baujahr: 2009 Zustand: gebraucht, unter Strom in Produktion Betriebsstunden: 34.000h Spindeldrehzahl 18.000 U/min Werkzeugmagazin 48 Werkzeuge Weitere Informationen folgen.

Kläger VBS 405 S Vertikalbandsäge / Metallbandsäge Hersteller: Kläger Typ: VBS 405 S Zustand: gebraucht, sehr gut Baujahr: 2006 Schnittbreite: 400 Tischneigung rechts/links 45°/15° Tischgröße 607 x 607 mm Sägebandbreite: 3-20 mm Sägebandlänge: 3300-3400 mm Bandgeschwindigkeit: 15 ? 300 M/min. Länge: 1120 mm Breite: 740 mm Höhe: 1930 mm Gewicht: 510kg ? Ideal Sägebandschweißgerät ? Original Dokumentation ? Maschinenfüße

Overview This Gronemeyer VFA is a vertical conveyor for glass bottles, built in April 2020 by Gronemeyer Maschinenfabrik GmbH & Co. (Höxter, Germany). It raises bottles between the levels of a filling line and works with two synchronously running endless chains whose carrier elements take the bottle from both sides, so the container is guided upright over the whole climb. The nominal capacity is 45,500 bottles per hour at a conveying speed of approximately 60 m/min. The conveying width is set by hand crank across a range of 20 to 150 mm, so a format change needs no tooling. The machine is enclosed in transparent guarding, has service doors with safety switches, an automatic central lubrication system and a pneumatic chain tensioning station. It is currently being dismantled and can be inspected at BEVMAQs warehouse in Germany from early September 2026. Technical data Manufacturer: Grone ...

Stephan Vacutherm VM/MC 800/20 vacuum processing system with Stephan Microcut MCH20 high-speed cutting and emulsifying unit. The Stephan Vacutherm is a highly versatile vacuum processing and cooking system for the food industry, designed to combine several processing steps in one compact installation. Depending on the product and recipe, the system can be used for mixing, dispersing, fine cutting, emulsifying, homogenising, heating, cooling, deaeration and pasteurisation. The vacuum processing vessel has a nominal batch capacity of approximately 800 litres. The system is particularly suitable for the production of products such as sauces, dressings, mayonnaise, emulsions, spreads, convenience foods, purees and other liquid or semi-liquid food products. It can process both liquid and solid ingredients and is capable of incorporating particles or other ingredients during processing., A maj ...

vertical machining center, year 2001, CNC S3045E. Used machine. More info & price on IndustrialBuyer.

General SKU328Y700 LocationBarneveld MakeExtrella TypeST-EM No.91017 Pressure Working pressure6 Bar Vacuum possiblecheck Number of vertical pressure tanks1 Main Features MaterialGlass Volume4210 Ltr. Pressure6 Bar Specified Features - Pressure vessel Capacity4210 l. Vessel sizesø 1600 x 2200 mm Dished topcheck Dished bottomcheck ManholeDN600 Top connectionscheck OutletDN80 Max. temperature—10 / 200 °C MaterialGlass - Enamel (TPE-2000) General Year of construction1991 Mounted on legscheck Floorspace1,60x1,60 m Total height3,20 m Weight2100 kgPressure vesselsNew arrivalsEstrellaTanks > Pressure vesselsNew arrivalsBrand > Estrella What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. P ...

General SKU328Y701 LocationBarneveld MakeEstrella TypeST-EM No.91016 Pressure Working pressure6 Bar Number of vertical pressure tanks1 Main Features MaterialGlass Volume4210 Ltr. Pressure6 Bar Specified Features - Pressure vessel Capacity4210 l. Vessel sizesø 1600 x 2200 mm Dished topcheck Dished bottomcheck ManholeDN600 Top connectionscheck OutletDN80 Max. temperature—10 / 200 °C MaterialGlass - Enamel (TPE-2000) General Year of construction1991 Mounted on legscheck Floorspace1,60x1,60 m Total height3,20 m Weight2100 kgPressure vesselsNew arrivalsEstrellaTanks > Pressure vesselsNew arrivalsBrand > Estrella What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barn ...

The machine is in good technical condition; testing is possible by prior arrangement. It is designed for machining parts made of wood, plastic, and composite materials. It features the Siemens SINUMERIK 840D/810D control system.

Manufacturer: FERMAT Model: VMF 1000 CNC Year: 2008 Condition: Used Stock number: 9494 Control System: FANUC Series Oi-MC Switch-on hours: 25998 h Work table length: 1300 mm Work table width: 600 mm Spindle drive power: 15 kW Speed: 10000 1/min X-axis travel: 1006 mm Y-axis travel: 598 mm Z-axis travel: 600 mm Machine weight: 5000 kg

Manufacturer: Pinnacle Model: VMC 2000S Year: 2015 Condition: Used Stock number: 9499 Control system: HEIDENHAIN Work table length: 2200 mm Work table width: 850 mm Maximum vertical spindle speed: 8000 1/min X-axis travel: 2000 mm Y-axis travel: 900 mm Travel Z axis: 850 mm Machine weight: 16000 kg

Key data: 1120 mm, 510 mm, 510 mm

CNC vertical machine center. Control unit - MAZATROL M32B Dimensions: 4000x3000x3000mm Table: 1460x510mm Max material weight: 800kg Automatic magazine: 24 tools Tool holder: CAT 40

Vertical milling machine Viktor 1 1/2 VA BJ 1976

A vertical CNC machining center is offered. X/Y/Z-axis travels: 560mm/410mm/381mm, spindle speed: 60-6000rpm, drive power: 3.7/5.5kW, table size: 410mm × 900mm, max. table load: 300kg, tool shank: ISO 40 (MAS-BT40), rapid traverse X/Y/Z: 24/24/18m/min, control: Mazatrol CAM M-2. Equipped with original parameter lists. Weight: approx. 4200kg, overall dimensions X/Y/Z: approx. 2300mm/2000mm/2641mm. The program is missing because the machine has been disconnected from power for several years. Documentation available. Inspection possible by appointment.

Key data: 800 mm, 500 mm, 540 mm

CNC Vertical Machining Center MIKRON VCE 800 W Pro With track control Heidenhain iTNC 530 Year of Make: 2004 Travel: X 800 Y 500 Z 540 Speed range: 30 – 10,000 rpm continuously variable ( SK 40 ) With the following accessories: Rigid angle table 910 mm x 500 mm clamping surface Vertical tool changer with 24 magazine positions ( SK 40 ) Full protection cabin with sliding doors and interior lighting Direct displacement measuring system (Heidenhain glass scales) Electronic handwheel Spindle cooling unit Chip rinsing gun Signal lamp Spiral Screw Conveyor Coolant Setup Operating Instructions

Vibrating Screening Machine Manufacturer: Vibra Schultheis Type VSB No. 07 327 2-cover screen, stainless steel 3x Screen frame without covering Diameter 60 cm Power 0.75 kW

Vakuu lifting device for attachment to an overhead crane = - Manufacturer: Aerolift - For lifting and turning up to 90 degrees - Max. load capacity: 16 t - Equipped with 8 suction plates, each approx. 60 x 120 cm in size - With 3 vacuum pumps

turning diameter:250 mm swing diameter:250 mm turning height:200 mm total power requirement:37,7 kW chuck diameter:315 mm spindle speed max.:5500 1/min travel -x axis:625 mm travel -y axis:+100/-80 mm travel -z axis:250 mm worktool system:VDI 30+40 weight of the machine ca.:8 t The synchronous spindle is powered with 37.7 kW of power, a torque of 300 Nm and a maximum speed of 5,500 rpm. Typical components are ball cages, ball hubs, gear wheels, sliding sleeves, pump wheels, flanges, synchronizer rings, bearing rings and pivot pins. The machine bed is made of Hydropol, a mixture of special concrete and steel, which ensures the greatest smoothness and precision even with larger components and powerful machining.

faceplate diameter:800 mm power requirement:110 kW weight of the machine ca.:37.000 / total 52.000 t transport measurements machine:5,07 x 2,98 x 3,90 m clamping diameter:800 mm :Ø 800 x 720 mm Tool bore:Capto C6 tools in tool magazin:2 x 80 With C-Axis

faceplate diameter:1600 mm power requirement:80 kW weight of the machine ca.:25 t dimensions of the machine ca.:4,4 x 4,62 m max. workpiece diameter:2000 mm max. diameter of face turning:1800 mm tool taper:ISO50 The machine has been regularly serviced and is in good technical condition. With C-Axis

faceplate diameter:1400 mm swing diameter:2000 mm turning height:1500 mm main drive:80 kW faceplate speeds from - to:1 - 365 U/min milling motor:37 kW ram head dimension:240 x 240 mm max. ram stroke:1250 mm total power requirement:133 kVA weight of the machine ca.:50 t dimensions of the machine ca.:11 x 5 x 6,4 m Machine was overhauled in 2008 by OEM New control CNC SIEMENS 840 D automatic tool changer 72-pcs C-axis with driven tools Angle-, straight tool holders with CAPTO holder Coolant device Chipconveyour

x-travel:1660 mm y-travel:760 mm z-travel:660 mm weight of the machine ca.:8700 t dimensions of the machine ca.:4.320 x 3.380 mm distance spindlenose - table min./max.:808 mm distance work spindle /surface of the table:155 - 815 mm Machine height:2850 mm floor space required (w/o switchgear cabinet):4.320 x 3.380 mm spindle motor:11 (10 Minuten) /7,5 (30 Minuten)/ 5,5 (Dauerbetrieb) kW tool taper:SK 40 Spindle RPM:40 - 7.000 (Standard ) / 40 - 10.000 ( Option ) 1/min surface area:2.000 x 760 mm max. table load:1.000 kg feeds X-axis:1 - 5.000 mm/min rapid traverse X-axis:24.000 m/min rapid traverse Y-axis:24.000 feeds Y-axis:1 - 5.000 mm/min feeds Z-axis:1 - 5.000 mm/min rapid traverse Z-axis:20.000 m/min

x-travel:1020 mm y-travel:510 mm z-travel:510 mm Table 1,200 x 530 mm Max. table load 800 kg Spindle mount ISO 40 Spindle speeds 10,000 rpm Drive power 14.5 kW Tool changer 20-position Coolant system External cooling Chip conveyor Yes The Y-cover is leaking (see photos)

faceplate diameter:1800 mm swing diameter:2000 mm turning height:1170 mm z-axis:1000 mm cross rail adjustment - vertical:800 mm faceplate speeds::2,5 - 280 workpiece weight:12 t feeds:1 - 6000 mm/min max. torque on the faceplate:50000 Nm total power requirement:85 kW weight of the machine ca.:41 t dimensions of the machine ca.:5,6 x 4,8 x 4,6 m Machine retrofit and overhould in 2005 with SIEMENS 840 D powerline control - 6 jaw hydraulic power chuck - tool changer for 12 tools - chip conveyor, coolant attachment, splash housing - various tool holders

faceplate diameter:1000 mm swing diameter:1600 mm turning height:1200 mm main drive:75 kW faceplate speeds from - to:7 - 800 U/min milling motor:25 kW milling head speed:7 - 3000 U/min milling spindle - taper:ISO 50 cross rail adjustment - vertical:800 mm ram head dimension:240 x 240 mm weight of the machine ca.:40 to dimensions of the machine ca.:9 x 7,8 x 6,0 m Machine general overhould in 2004 and equiped with Siemens 840 D control - tool changer rack magazine - C-axis, live tooling, - Transmit function electronical Y-axis - angular milling head - complete splash housing - coolant device, chip conveyor

faceplate diameter:1400 mm swing diameter:2000 mm turning height:1270 mm main drive:80 kW faceplate speeds from - to:1 - 355 U/min max. workpiece weight:6.000 kg milling motor:37 kW milling head speed:7 - 3000 U/min milling spindle - taper:ISO 50 cross rail adjustment - vertical:800 (8 x 100 mm) mm ram head dimension:240 x 240 mm max. ram stroke:1250 mm weight of the machine ca.:50 to total power requirement:133 kVA dimensions of the machine ca.:11 x 5 x 6,4 m Machine general overhould in 2008 and equiped with CNC SIEMENS 840 D control - tool changer for 72 tools - C-axis, live tooling - angular- and straight tool holder head with CAPTO taper - Transmit function - complete splash housing - coolant device, chip conveyor - diverse accessories

Article: Vertical turning and grinding centre Manufacturer: EMAG Type: VSC 250 DS Yob: 2008 Control: SIEMENS 840D Grinding spindle speed: 30,000 rpm Rotation spindle speed: 3,000 rpm Tool places turret: 12 Cooler for spindle and machine bed cooling Cooling lubricant - lifting station (no independent cooling lubricant supply) Chip conveyor Parts handling Air through the spindle Two clamping circuits through the spindle (air and oil) Unfortunately, the grinding spindle is defective. However, this can be overhauled in a spindle factory. Otherwise the machine is in a very good condition and fully functional. Please, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com

The Alfa Laval SMP Valve is a specialized valve used primarily in hygienic applications, particularly in the food, pharmaceutical, and biotechnology industries. Heres more information about the SMP Valve:, Key Features:, - Hygienic Design: The SMP Valve is designed to meet stringent hygiene standards and is typically constructed from stainless steel, making it suitable for applications where cleanliness is crucial., - Flow Control: It is used for controlling the flow of various fluids in processing systems, ensuring precise regulation and minimizing the risk of contamination., - Easy Maintenance: The design facilitates easy access for maintenance and cleaning, which is essential in industries where sanitation is paramount., - Robust Construction: Built to withstand demanding operating conditions, the valve is resistant to wear and corrosion, which contributes to its longevity and reliabi ...

NEW, 250 cm width, 2.15 m³ capacity, 585 kg dead weight, with Merlo ZM2 attachment, Also other recordings such as Atlas, Avant, Bobcat, Cat, Claas, Deutz Fahr, Dieci, Faucheux, Genie, Giant, Hercules/Everun, JCB, John Deere, Kramer, Liebherr, Mailleux, Manitou, Merlo, Mustang, New Holland, Paus, Schäffer, SMS, Terex, Volvo, Weidemann, Zettelmeyer available!

NEW, 200 cm width, 493 kg weight, 1.75 m³ capacity, suitable for Manitou attachment, Also other recordings such as Atlas, Avant, Bobcat, Cat, Claas, Deutz Fahr, Dieci, Faucheux, Genie, Giant, Hercules/Everun, JCB, John Deere, Kramer, Liebherr, Mailleux, Manitou, Merlo, Mustang, New Holland, Paus, Schäffer, SMS, Terex, Volvo, Weidemann, Zettelmeyer available!

NEW, 220 cm width, 550 kg deadweight, 1.90 m³ capacity, with Merlo ZM2 attachment, Also other recordings such as Atlas, Avant, Bobcat, Cat, Claas, Deutz Fahr, Dieci, Faucheux, Genie, Giant, Hercules/Everun, JCB, John Deere, Kramer, Liebherr, Mailleux, Manitou, Merlo, Mustang, New Holland, Paus, Schäffer, SMS, Terex, Volvo, Weidemann, Zettelmeyer available!

vertical machining center, year 2004, CNC Ultimax. Used machine. More info & price on IndustrialBuyer.

Vacuum frying installation consisting of high vacuum fryer, dimensions: 1500 mm x 1500 mm x 2500 mm, s/s oil tank, dimensions: ø 800 mm x 2350 mm, tubular heat exchangers, dimensions: 2600 mm x 800 mm x 1900 mm and s/s frame with 2 vacuum pumps, dimensions: 900 mm x 800 mm x 1500 mm. The lot has already been professionally dismantled and stored. The capacity of the fryer is 25-30kg end product (appr. 150kg fresh input) p/h.

Élmüker-Vincze Ltd. twin double jacketed process machine with steam injection, type: VK-2x 25 Vákuumkutter, number: 5-2012, year of construction: 12-2012, maximum steam pressure: 2.5 bar, heating capacity: 95°C, volume: 2x 25 liter, 2x scraper agitators, 2x Indag product lobe pumps, total dimensions: 2900 mm x 940 mm x 2180 mm.

table size: 3000mm x 1500mm; pressure: -0,85 bar; machine length: 3100mm; machine width: 1450mm; weight: 480kg;

table size: 3000mm x 1500mm; pressure: -0,85 bar; machine length: 3100mm; machine width: 1450mm; weight: 425kg;

<br>AGFA Apogee Print-Drive Series 3 VLF with Inkdrive, DQS and TIFF output. The Optionc Inkdrive (ZIP3), DQS, and TIFF output are enabled in the dongle. Consisting of: CD and latest update, dongle, APIS card and APIS adapter<br><br><br>Verf Gbar: now

<br>AGFA Apogee Print-Drive Series 3 VLF connect to open. Open is Connect enabled in the dongle. Consisting of: CD and latest update, dongle, APIS card and APIS adapter<br><br><br>Verf Gbar: now

Nitrogen generators membrane or PSA systems for laboratory up to production (500 L/h to several m3/h) No more gas cylinders in laboratory, plant or car repair shop (tyre gas)! Wear-free operation >99.5% pure nitrogen from mostly existing in-house compressed air Constant and safe gas generation guarantees reliable analytical results Operation-free 24-hour operation also in hazardous areas Safe operation due to low operating pressures Economically thanks to fast payback even on a technical scale! N2 production according to the membrane process The nitrogen generators continuously supply nitrogen up to a maximum purity of 99.5%. After the compressed air flows through highly effective filters, the compressed air is decomposed in a hollow fiber membrane module into a concentrated nitrogen flow and an oxygen-enriched portion. The membrane process has the great a ...

AGFA Viper 3.04 Software rip consisting of dongle, CDs (original 3.01 and update 3.04), APIS board and APIS adapter Available now

<br>AGFA Apogee Print-Drive Series 3 VLF with Inkdrive, DQS and TIFF output. The Inkdrive(CIP3), DQS, and TIFF output options are enabled in the dongle. Consisting of: CD and latest update, dongle, APIS card and APIS adapter<br><br><br>Verf Gbar: now

<br>AGFA Apogee Print-Drive Series 3 VLF connect to open. Open is Connect enabled in the dongle. Consisting of: CD and latest update, dongle, APIS card and APIS adapter<br><br><br>Verf Gbar: now

AGFA AccuSet 800 with AGFA Viper Rip. System is completely tested and cleaned. Resolutions: 1200, 1800 and 2400 dpi - the system is complete and includes accuset, supply & recording cassette, APIS cable, CD's, software and dongle. Includes Techkon film densitometer. We will be happy to send you further information and pictures. Available now