impact used for sale

sheet width: 2300 mm plate thickness: 1,5 mm distance between columns: 2400 mm impact length: 1000 mm total power requirement: kW weight of the machine ca.: 0,5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 100 mm cross-section heigth:: 40 mm feed:: 2 - 999.999,9 mm Condition: new, Specification: Impact knife cutting machine CC-600/40 for hoses and profiles - contact length: 600 mm - product diameter: 40 mm - belt width: 100 mm - Tractive force: 400 N to 800 N - Drive: 2 drives upper and lower belt - Conveyor belt speed: 100 m/min - Drive feed, cutting motor: Servo drives - Cutting capacity with blade max.: 4,000 1/min - Connected load: 3.5 kW - Dimensions L/H/B: 1,900 x 1,650 x 960 mm - Weight approx.: 580 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydr. High-speed single-column press Fabr. DUNKES type HZS 40Machine -No: H 77-581, built in 1981Press force: 40 tOperating pressure: 270 barStroke: 150 mmInstallation height: 400 mmOutreach: 280 mmRapid traverse: 400 mm / sec.Rapid traverse to: 400 mm / sec.Pressing under full load: 14 mm / sec.Table height: 820 mmTable surface: 600 x 515 mmDiarrhea hole in the table: 100 mm Drm.Drive power: 7.5 kWWeight: 3.1 tOil filling: 230 lExternal dimensions: 850 x 1200 x 2390 mmWith- Cutting impact damping- Safety 2-hand control- self-holding with rapid traverse shutdown- Electric return stroke limitation- Setup tip circuit- Fully automatic workflow- Emergency stop switch- stepless force preselection- graduated Adj. mech. depth stop- Switching in the lower stroke rangexa0xa0xa0 Lift and time changeoverxa0xa0xa0 Lift and pressure changeover- separate hydraulics for drawing cushionsused, in good co ...

DYNAJET 350th HELI The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner 350th with up to 350 bar working pressure stands out in addition to its ease of use in particular due to its low weight, its compact dimensions and its high performance and safety level. Construction - 1-axle chassis for easy manoeuvring - Self-supporting and indestructible framework for weight optimization - Crane eyelet for easy transport and handling - Operating hours counter for optimal post-calculation - Underrun protection for additional safety - Frame in dip painting technology for high corrosion protection and highest surface quality - Targa concept with separation between the unit side and the operating side for enormous advantages in ergonomics, the Overall machine safety and noise reduction - Impact-resistant lockable hoods made of glass fiber reinforc ...

DYNAJET 350th HELI high pressure hot water cleaner. Including 1st UVV WITH arrival and maintenance (plus spare parts) on the same date (value approx. 1,500 net). The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner 350th with up to 350 bar working pressure stands out in addition to its ease of use in particular due to its low weight, its compact dimensions and its high performance and safety level. Construction - 1-axle chassis for easy manoeuvring - Self-supporting and indestructible framework for weight optimization - Crane eyelet for easy transport and handling - Operating hours counter for optimal post-calculation - Underrun protection for additional safety - Frame in dip painting technology for high corrosion protection and highest surface quality - Targa concept with separation between the unit side and the operating side for eno ...

Impact machine Rego Model: SM 4 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whisk 1 new whisk 1 40 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 2 kW,16A-CEE plug Dimensions: 720 x 680 x 1710 mm, WxDxH Weight approx. 285 kg. Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner Visit our large stock of agitators!

Impact machine stirring machine Rego Model: SM 3 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whiter 1 new whipped beating 1 32 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 1,5 kW,16A-CEE plug Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner

Impact machine stirring machine Rego Model: SM 3 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whiter 1 new whipped beating 1 32 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 1,5 kW,16A-CEE plug Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner

Impact machine stirring machine Rego Model: SM 3 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whiter 1 new whipped beating 1 32 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 1,5 kW,16A-CEE plug Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner

Impact machine stirring machine Rego SM 3 E / SM 2000 overhauled with automatic timer 2 working functions 1 x stirring / 1 x beating 1 new whiter 1 new whipped beating 1 32 litre stainless steel boiler new Working shaft/stirring shaft new Boiler stroke electric Boiler lighting Connection 400V, 16A-CEE plug Used machine overhauled

Ready for operation with 2 sets of new impact strips

Stirring machine Rego Model: SM 4 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whisk 1 new whisk 1 40 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 2 kW,16A-CEE plug Dimensions: 720 x 680 x 1710 mm, WxDxH Weight approx. 285 kg. Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner Large selection of impact machines!

Stirring machine Rego Model: SM 4 Impact machine 40 liters 2 working functions (1x stirring / 1x beating), boiler lighting, 1 stainless steel boiler 40 liters new 1 new whiter 1 new whipped beating Infinitely variable power adjustment and rash adjustment, Manual boiler height adjustment New wave of work DGUV V3 tested Connection 400V, 2 kW, 16A-CEE plug Dimensions: 680 x 720 x 1710 mm Used machine overhauled with 6 months warranty.

General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 100 mm - B-axis ±110° with pneumatic locking - Tools magazin disc with 1x24 positions - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 5 bar; 20l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor - USB interface, Ethernet interface; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTurning diameter500 mmMax. Turning Length750 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmC-Axis Speed-5000 rp ...

A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Used fine impact mill Hosokawa Alpine Contraplex CW 400 pin mill. The Contraplex pin mill is fitted with two contrarotating pin discs achieving high relative speeds, allowing it to reach finer end products than our traditional universal mill type UPZ. This grinder is suitable to comminute many different products for all kind of industries, like chemicals, food, pharma, etc. Material ...

Stirring machine Rego Model: SM 4 Impact machine 40 liters 2 working functions (1x stirring / 1x beating), boiler lighting, 1 stainless steel boiler 40 liters new 1 new whiter 1 new whipped beating Infinitely variable power adjustment and rash adjustment, Manual boiler height adjustment New wave of work DGUV V3 tested Connection 400V, 2 kW, 16A-CEE plug Dimensions: 680 x 720 x 1710 mm Used machine overhauled with 6 months warranty.

Used Hosokawa Alpine Zirkoplex ZPS 315 classifier mill A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery The Hosokawa Alpine Zirkoplex ZPS impact classifier mill is perfect for the fine grinding of different dry materials with a precise control over the particle´s top cut thanks to its integrated classifier wheel design, using the Alpine classifier ATP. It can be used to pulverize different products and within different industri ...

Used Hosokawa Alpine Zirkoplex ZPS 315 classifier mill A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery The Hosokawa Alpine Zirkoplex ZPS impact classifier mill is perfect for the fine grinding of different dry materials with a precise control over the particle´s top cut thanks to its integrated classifier wheel design, using the Alpine classifier ATP. It can be used to pulverize different products and within different industri ...

Air steam die forging hammer : Capacity : 16 tons, Nominal mass of drop parts : 16000 kg, Impact energy : 400 KJ, Ram stroke : 1500 mm, Ram stroke per minute : 20, Distance clear between guides : 1180 mm, Ram dimensions front to back : 1500 mm, Die holder dimensions front to back : 1600 mm, Bottom die impression to floor distance : 500 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions : - Floor space : 4500 x 2450 mm, - Height above floor level : 7920 mm, Mass of anvil block : 325 tons, Total weight of hammer : 425 tons.

Impact machine stirring machine Rego Model: SM 4 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whisk 1 new whisk 1 40 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 2 kW,16A-CEE plug Dimensions: 720 x 680 x 1710 mm, WxDxH Weight approx. 285 kg. Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner

Impact machine stirring machine Rego Model: SM 4 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whisk 1 new whisk 1 40 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 2 kW,16A-CEE plug Dimensions: 720 x 680 x 1710 mm, WxDxH Weight approx. 285 kg. Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner

Hydr. Single column press make MÜLLER type CD 16.11.55Machine -No: 10480 Year 1983Press force: 16 tTable size: 450 x 350 mmPiston diameter: 90 mmBear size: 320 x 240 mmPiston stroke: 100 mmDiarrhea opening in the table: 100 mmDimensions L x W x H: 700 x 1100 x 2005 mmWith- Cutting impact damping- safe control- Two-hand release- Photocell- infinitely adjustable pressure settingused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Hydraulic 20 T single-stand production press for the production of lightweight concrete parts Here are the technical data of the offered machine: If the press does not exactly meet your requirements profile, please request an individual offer exactly according to your wishes with one click: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your wishes at surprisingly low prices! Technical data + information: a) Closing speed up to 10 mm/sec b) Opening speed up to 20 mm/sec c) Open maximum height 300 mm d) Pressing speed 4 – 10 mm/sec. ( adjustable via rotary knob ) e) Mould size 600x800 mm f) Plunger size950x600 mm g) Manual lubrication( via lubrication nipples ) h) Pressure setting from 5 T to 20 ( adjustable via rotary knob ) i) Travel 300 mm j) Construction, commissioning, instruction against separate calculation  ...

Machine Type Electrode Inverter Welding Rectifier Böhler brand Type Uranos 1500 Connection voltage 1 x 230 Volt Setting range 5 – 150 amps Duty cycle 30 % ED at 150 Ampere 60% ED at 125 amps 100% ED at 110 amps Current adjustment infinitely variable weldable material thickness 4 mm Cooling inverter by built-in fan Version portable mounting system Fuse 16 amps Dimensions L x W x H 260 x 120 x 190 mm Weight 3 kg Age 6 months Special accessories carrying strap Condition workshop tested, as new, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece attachment glass 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2 rows 30 piece rod elec ...

(Schloemann) Beche DGH 40 Ton ( Revamped by Schuler group 2019) Manufacturer: BECHE (Schloemann) Type: DGH 40 YOM: Revamped 2019 Machine Number: 2412-HW Including 12 Ton Wellman manipulator Impact work: 40,000 mkg Total bar lift.:1.250 mm Maximum number of strokes:80 Pro Minute Average score: 6 Pro Minute Air consumption per ten blow Blow in . m in required air at the strongest hit: 6.8 Cold Air Compressor performance in m3/min: 41 Cold Air Compressor performance in m3/min:27 Hot air (160° C) Power requirement of the compressor in hp:260 Cold Air Power requirement of the compressor in hp:180 Cold Air Air tank capacity:30 m3 Steam consumption per hit with the strongest hit:3.5 kg Steam consumption per minute (saturated steam):21 kg Clear width between the guides: 1200 mm Maximum singing sounds: 2700 mm Lowest overall height of the dies without dovetail: 575 mm O ...

cutting diameter: 225 mm saw band length: 2455 mm table height: 850 mm cutting width: 245 x 150 mm cutting speed: 45/90 m/min dimensions of saw-band: 2480 x 27 x 0,9 mm : 90 mm : 90 mm : 145 mm Impact energy: 145 mm connected load frequency: 400 Volt total power requirement: 1,5 kW weight of the machine ca.: 0,2 t dimensions: 1,43 x 0,72 x 1,7 m - Miter cuts up to 60 ° left -Vise with quick release device -Band tension control -Electr. Automatic cooling The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Impact machine Rego SM 2 overhauled The machine when it comes to striking! 1 new whisk 1 new whisk and 20 litre stainless steel boiler new Stand-alone machine 2 working functions 1 x stirring / 1 x beating Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting with automatic timer and EMERGENCY STOP DGUV V3 tested Connection 400V, 1 kW, 4 Amp, 16A-CEE plug Dimensions: 640 x 615 x 1380 mm, WxDxH Quality from a specialist company! Used machine completely overhauled with 6 months warranty!

CITIZEN CINCOM A20 VIPL CNC lathe built in 2006 ensures the highest precision and efficiency in the production process. During machining, the specially designed bed with its rigid structure and high thermal stability effectively reduces the heat impact, resulting in increased machine life and reliability. All of this, combined with a modular design with a reduced number of parts, makes the CINCOM A20 VIPL CNC lathe ideal for various types of production. Workpieces with a maximum diameter of 20 mm and a length of 135 mm are machined in 7 axes by a powerful main spindle which is synchronised with an AC motor, forming an electrospindle. A bushing driven by a separate AC motor is also synchronised with the machine’s main spindle. The operator’s panel consists of an intuitive FANUC 32i CNC controller, a memory card slot and an electronic wheel located next to the monitor designed to ch ...

Impact machine stirring machine Rego Model: SM 4 overhauled with automatic timer The machine when it comes to striking! 2 working functions 1 x stirring / 1 x beating 1 new whisk 1 new whisk 1 40 litre stainless steel boiler new Working shaft/stirring shaft newly revised Powerful and robust technology Boiler lighting, timer EMERGENCY STOP protection circuit DGUV V 3 tested Connection 400V, 2 kW,16A-CEE plug Dimensions: 720 x 680 x 1710 mm, WxDxH Weight approx. 285 kg. Quality from a specialist company! Used machine overhauled with 6 months warranty! Option: Stainless steel pedestal Gas ring burner

Fully automatic stretch film packaging machine with scale & labeler Packing Plant / Wrapper + Labeler DIGI AW-5600 FX The AW-5600 FX is an automatic weighing, packaging and labeling system with high performance for ease of use and environmental friendliness. The packaging machine reduces the workload with easy and simplified operation. It protects film and label consumption through linerless labels in order to keep costs and environmental impact low. Goods such as cheese, meat or fruit and vegetables can be packaged easily and visually appealing. Technical data Wrapper DIGI AW-5600 FX 220-240V / 50-60 Hz / 1.8 kW suitable for Food-Tainer bowls Performance up to 17 packets/min Film width: 350 - 500 mm Year of construction: 2018 Total weight approx. 250 kg Digi marking system 3/6 kg, Min 20g, e=1/2g Calibrated until 31.12.2022 Function tested, ma ...

Standard equipment: robust, high-quality and inclined rotary hood for easy reading of the speed LED lighting quickly adjustable and ergonomic drilling depth stop infinitely variable speed control Connection cable with SCHUCO plug (1.2 m) Undervoltage outlets Drilling protection with electr. Hedge thermal overload protection Emergency Stop Impact Button Weight in kg: 44 Motor kW: 0,45 AC 230 V Speed 1/min: 250-3000 Drilling capacity mm: - Steel Ø 12 mm - Aluminium Ø 20 mm - Softwood Ø 40 mm - Drilling depth 60 mm - Projection 220 mm - Saeulen diameter 70 mm - usable table area (W x L) 300 x 250 mm - T-groove size number 2, distance 100 mm Dimensions width 14/26 mm - Spindle B 16 - Speed display digital - Drilling depth display: scale - Drill depth stop: quickly adjustable stop ring - Feed: by hand - FACTORY WARRANTY: 3 years - free domicile incl. packa ...

x-travel: 1050 mm y-travel: 600 mm z-travel: 600 mm table-size: 1200 x 600 mm tool adaptor: SK 40 turning speed range: 12000 U/min power requirement: 40 kW Control: Sinumerik Steuerung 828D rapid traverse Z-axis: 30000 mm/min rapid traverse X- and Y-axis: 30000 mm/min workpiece weight: 800 kg no. of tools in the magazine: 30 Stück dimensions: 4319 x 2286 x 2928 mm weight of the machine ca.: 7000 kg immediately available from stock - Siemens Sinumerik control 828D with 15.6 inch touch display - Difficult execution - High productivity - High reliability - Heavily ribbed, torsion-free machine base - Profile rail with revolving rollers on all axes for high loads - High torque servo drives, direct to the ball screw in all three axes - Precision-ground, preloaded, heavy-duty ball screw (Ø 40 mm x P16 x C3) for high rapid traverse speeds in all axes - Telescopic guideway cover on all three a ...

bore capacity in steel (diameter): 30 mm throat: 270 mm bore stroke: 125 mm : 4 Motor output: 9 speeds: 120 - 1810 U/min With V-belt drive in a modern design / 3020640SET - Heavy execution of the whole machine - Very smooth running thanks to the new spindle design - industrial engine - Separate emergency stop impact switch - drilling depth stop - LED machine light integrated in the drill head - Precisely machined, stable drilling table with diagonal T-slots with circumferential cooling water channel - Drilling table can be tilted ± 45 ° and rotated 360 ° - V-belt cover with safety switch - Precision spindle bore - Machine operation of safety electronics in 24 V DC voltage - Guaranteed concentricity = 0.02 mm measured in the drilling spindle - Thick-walled steel column for high force absorption and stability - Solid, large base plate with T-slots scope of delivery - Keyless chuck 0 - 1 ...

Rental Hosokawa Alpine UPZ 100 cryogenic system (LN2) by Alpine Rentals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX Suitable for cryogenic grinding with LN2 Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system with grinding tools of choice, small feeding hopper with a dosing channel, cooling screw to feed the LN2, LN2 container, filter and barrel to collect the fines. Includes an operating panel, switch cabinet and a vacuum cleaner. LN2 to be provided on-site This small size system with an universal mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. Suitable for the cryogenic grinding with liquid nit ...

Fully refurbished Hosokawa Alpine UPZ 100 used system by Alpine Originals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX, not suitable for inert operation (N2) Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system in large table fitted with pins (other grinding tools of choice could be offered for an additional price), small feeding hopper with a dosing screw, filter and barrel to collect the fines, blower and piping. Includes a relay control panel. This small size system with an universall mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mil ...

Trane CHHT0M4TKA0N092A 289.9 kW Screw Compressor | ChillerTech - Original Spare Parts! Reliability and honesty! Genuine spare parts for Trane equipment in the cooling capacity range (Qch) from 1 kW to up to +1800 kW are a guarantee of satisfaction and safety. Taking into account the access to unlimited possibilities and even a storage area of +3500 m2, it is the best choice in terms of, m.in, screw, reciprocating, centrifugal and even scroll compressors. It is worth mentioning that as ChillerTech, we provide assistance in the field of service and repair of the above-mentioned devices throughout Poland, so you do not have to worry about possible downtime, problems or even damage. It's an investment for years! A Trane CHHT0M4TKA0N092A screw compressor with a cooling capacity of 289.9 kW under nominal conditions (according to the supplier) enables us to operate highly efficiently as w ...

Impact mill Böhringer RC12 Brand: Böhringer Type: RC12 Inlet opening : 1250 x 1000 mm Drive : Electric motor 100 kW

Hazemag Impact Mill AP 4 complete with drive, spare rotor + spare parts. Capacity: approx. 150 T/h. Power requirement: 35 to 80 kW. Mouth width : 700 x 1000 mm. Weight: approx. 11000 kg

Kleemann Impact Mill Brand: Kleemann. Inlet opening: 1430 x 900mm Dim. Rotor: 1400 x 1000mm Incl.: electric motor 160 kW

Kleemann Impact Mill Brand: Kleemann. Type: SHB 14-1000 Inlet opening: 1430 x 1050mm Dim. Rotor: 1400 x 1000mm Incl.: electric motor 160 kW

Impact mill MFL Type R-CI 100-100 Inlet opening 1020 x 760 mm Power requirement 90 kW electric motor Weight 9 ton

SBM Austria Impact Mill Type 8/5/3-SE Inlet opening : 390 x 465 mm Drive : 75 kW electric motor Incl. : steel construction, inlet/outlet hopper & electrical system.

Impact Mill Voestalpine Brand: voestalpine Inlet opening: 900 x 680 mm. Drive: 55 kW electric motor.

CNC machining center including laser edge type BIMA / Gx50 / E / 160 / 630 Specifications: IMA gantry machine in real GANTRY design Processing area: • Length in X direction with all aggregates (mm): 6300 • Width in Y-direction with all aggregates (mm): 1600 • Height in Z-direction with all aggregates (mm): 225 maximum clamping height including clamping device - the maximum workpiece thickness depends on equipment/application • Length in X direction with vertically positioned main spindle and tool diameter 20 mm: 6300 mm • Width in Y-direction with vertically positioned main spindle and tool diameter 20 mm: 2000 mm • Width in Y-direction with edging (mm): 1600 • Length in X-direction Single user processing without gluing (mm): 2 x 3050 • Length in X-direction free space center (mm): 200 • Length in X-direction Single user processing with gluing (mm): 2 x 2 ...

Kallfass Universa 400 with shrink tunnel and grab section Kallfass Universa 400 NT Year of construction 2003 The system is immediately available. The Universa 400 is included in the price of the complete system. The machine is technically overhauled and is in very good condition. Technical data: - Length of cross welding punch: 450mm - Welding punch passage: max. 200mm - Min. product length: 80mm - automatic length compensation to reduce the punch gap - Welding punch monitoring - Side sweat monitoring - Foil holding plate Pwq9ya - Control: Siemens S7-300 - Operating terminal with Sütron BT20 - Welding punch with replaceable welding strip - Side welding wheel-knife combination, can also be exchanged for a knife system - Processable films PE and PO - Year of construction 2003 - Shrink tunnel Kallfass Standard - Gripper section with inline belt - Curved band can be ...

Engine. Guillotine Shears Impact Shears Tin Shears Scissors Cutting Manufacturer: KRAMER Model TM IIa 3000x4,5 max. cutting length 3050 mm max sheet thickness at ST 40 4.5 mm Distance between uprights 3050 mm Projection 130 mm Table width 360 mm Strokes per min 30 pcs. Hold-down device 16 pieces Manual backgauge travel 5 – 550 mm Engine power 7.5 kw Machine weight 4000 kg Space requirements: W 3480 mm D 3600 mm H 1400 mm Foot switch Back gauge front support arms Angle stop The machine is in good condition and ready for immediate use. Machine runs very quietly. Forklifts available, freely loaded trucks Cheap shipping possible Location of the machine 48324 Sendenhorst for enquiries 0157-35496006 The price is net plus 19% VAT.

Kallfass Universa 400 with shrink tunnel and grab section Kallfass Universa 400 Year 2006 The system is immediately available. The Universa 400 is included in the price of the complete system. The machine is technically overhauled and is in very good condition. Technical data: - Length of cross welding punch: 450mm - Welding punch passage: max. 200mm - Min. product length: 80mm - automatic length compensation to reduce the punch gap - Welding punch monitoring - Control: Siemens S7-300 - Operating terminal with Siemens touch panel - Welding punch with replaceable welding strip - Side welding knife combination, can also be exchanged for a wheel knife system - Processable films PE and PO - Year of construction 2006 - Kallfass Compact 450 SO shrink tunnel - Gripper section with inline belt - Book magazine on gripper section - Ionization for blocking loose leaves - Cur ...

Kallfass Universa 400 with shrink tunnel, SlipTorque roller belt and conveyor belt Kallfass Universa 400 built in 2005 The system is immediately available. The price of the complete system includes the Universa 400, the Schlichter shrink tunnel, a SlipTorque roller belt and a conveyor belt. The machine is technically overhauled and is in very good condition. Technical data: - Length of cross welding punch: 450mm - Welding punch passage: max. 200mm - Min. product length: 80mm - Metronic embossing system - Control: Siemens S7-300 - Siemens Touch TP277 operator terminal - Welding punch with replaceable welding strip - Side welding knife combination, can also be exchanged for a wheel-knife system - Processable films PE and PO - Year of construction 2005 - Simple shrink tunnel DS-600 with switchable rotating bars - Conveyor belt 1000 x 400mm - SlipTorque roller conveyor 2 ...

TECHNICAL SPECIFICATIONS Manufacturer: HAZEMAG & EPR GmbH Description: Impact Roller Crusher Type: SB 1315R Year of construction: 2013 Design: driveless crawler chassis Operating hours: approx. 12,000 h Throughput: 600 t/h Bunker load: max. 80 t Feed grain: 0 - 1,200 mm Final grain: 0 - 250 mm Infeed width: 1,510 mm Inlet height: 1,670 mm Roller diameter: 1,300 mm Roller speed: 300 1/min Roller drive power: 250 kW Conveyor drive power: 2 x 55 kW Length chain conveyor: approx. 15,000 mm Light range chain conveyor: 1,200 mm Dimensions of the entire system (L x W x H, approx.): 23,500 x 6,700 x 5,700 mm Total weight: 110,000 kg (incl. tax container) SPECIFIC COMMENT - Mobile primary crusher plant for soft to medium-hard rock - low-precision comminution (designed for limestone) - Incl. 1 pc. gebr. Set of scratching irons with chain - Incl. control container If  ...

Center height: 205 mm Orbit diameter over bed: 410 mm Center width: 1000 mm Bed width: 260 mm Spindle nose: DIN 55029 (Camlock) 9, size 6 Travel cross slide: 220 mm Travel upper slide: 125 mm Spindle bore: 52.5 mm Spindle speeds: 20 - 3000 min-1 Speed control: Infinitely variable Mechanical counters: 2 Motor power: 3.75 kW Coolant pump: 0.13 kW Longitudinal feeds Z: 0.05 - 1.7 mm/rev Face feeds X: 0.025 - 0.85 mm/rev Whitworth Thread: (45) 2 - 72 TPI Metric threads: (39) 0.2 - 14.0 mm Diametric thread: (21) 8 - 44 DP Module thread: (18) 0.3 - 3.5 MP Quill diameter: 52 mm Inner cone quilt: MK 4 Quill stroke: 150 mm Dimensions: 2270 x 1120 x 1900 mm Weight, approx.: 1500 kg Characteristics: - Tool mesh accuracy according to DIN 8605 - Infinitely variable speed control (2 countershafts) - Finely balanced main spindle - Stable machine bed with hardened and gro ...