hot rolling mill used for sale

grinding length:1500 mm grinding width:700 mm workpiece height:580 mm table load capacity:2380 kp table speed -stepless-:5 - 35 m/min grinding wheel dia. x width:500 x 100 x 203 mm grinding wheel motor:18 kW speeds::stufenlos elektronisch total power requirement:35 kW weight of the machine ca.:12 t dimensions of the machine ca.:5,3 x 2,9 x 3,8 (3,18) m surface grinding machine, paper-filter, DRO 3 axis, automatic infeed, el.handwheel, full cabin

Geibel + Hotz FS 640 SDYear of manuf. : 2020 Control : Sonstige Grinding length : 600 mmGrinding width : 400 mm____________Description:Spindle:Speed:1.400 rpmPower:3,7 kWGrindingwheel dimensions:300 x 50 x 76,2 mmWorkingtable:Clamping surface:Magnettable, 600 x 400 mmTableloading (max.):600 kgTabledrive:HydraulicTablemovement:200 - 650 mmRapid travers:28 m/minGrindingarea:600 x 400 x 375 mmEquipment/Accessory:Measuringsystem:MotormeasuringsystemDressingunit :SinglecorndiamantCoolingmanagement:Cooling unit with paperbeltfilter, Tank capacity 140 lFurther accessory:Workingarea enclosure (partly), Working area lamp

1 x NEW 'Bainite' (India) Make 1000mm (42in) wide x 400mm (16in) dia two roll mill, Hydraulic nip adjustment (dual acting cylinders), Peripherally drilled chilled cast iron rolls (Hardness 65/72 Shore), with anti friction roller bearings, Friction ratio 1:1.08, Hinged guide plates, Lubrication system comprising pneumatic intensifier with grease reservoir, Electro pneumatic brake with power fail safe mechanism. Safety bars fitted to front and rear. Compact right angle drive with 45kW Siemens AC variable speed squirrel cage motor through heavy duty helical design direct drive reduction gearbox (SF 2), Back roll speed 18rpm/front roll 16.6rpm. All mounted on a compact design fabricated steel bedplate. Stainless steel tray underneath. Including electrical controls comprising Siemens G130 VFD drive and S7-1200 plc with HMI. CE marked, with full Technical file, Documentation and S ...

REVAMPED: 1990, WIDTH: 700-1400 MM, THICKNESS: 100 MICRONS - EXIT: 2 x 5 MICRONS 1500 M/MIN.,

Reed 42" x 16" Two Roll Mill. 40HP Motor, with clutch brake. Friction ratio 1.1 Manual Nips. On one-piece steel bedplate.

Qty. 1 Second-hand foil rolling mill plant Mfc.: World Co. (Japan) Type: 6-Hi – Non reversing mill Built: 2002 Application: Copper foil Width: 400 – 700 mm Coil weight: Max. 5 Ton Thickness Entry: 100 – 200 microns Exit: 5 – 100 microns Speed: 0-400/800 m/min. Thickness X-Ray unit AGC system Variable Crown Control Hydraulic servo equipment Main motor power: 200 kW DC Slitter line Mfc.: IHI Width: 150-700 mm Thickness 5 – 50 microns Degreasing line Mfc.: World Co. Strip width: 700 mm Thickness: 10-50 µm Treatment line Mfc.: Kawasaki Built: 2005 Width: 700 mm Thickness: 10-50 µm

Qty 1 x Shaw 60in x 22in two roll mill, Manual nip adjustment, Peripherally drilled rolls (front and back), Hinged guide plates, Sleeve bearings with motorised lubrication, Right angle drive gearbox with 115Kw DC variable speed motor, All mounted on a heavy duty bedplate. Carter stockblender mounted on too. Complete with controls etc and in very good condition.

1 x Heavy duty 2 roll mill Roll dimensions: 2100mm x 665mm dia. Hydraulic nip adjustment, Safety push bars, Peripherally drilled rolls, Sleeve bearings with grease lubrication, Right angle drive gearbox, with Siemens 240kW DC variable speed motor, Strip knives fitted to front roll, Heavy duty fabricated bedplate, Carter stockblender mounted on top.

Qty 1 x Schwabenthan 200mm dia x 450mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Jahnel gearbox with 10HP motor to each roll (variable speed), Variable friction ratio/roll speeds, Stainless steel interlocked guards and tray. Complete with electrical controls and in good condition. O/a dimensions 2700 x 1500mm

Qty 1 x Schwabenthan 150mm dia x 350mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Even/friction selectable gear ratios, Motor mounted under frame. Complete with electrical controls and in good condition. O/a dimensions 2400 x 850mm.

Reed 40” x 16” Two Roll Mill Hand operated nips Right angle drive Tray fitted beneath Mill Rolls

Key data: 190 mm, 450 mm

available Lab Mill! Description attached !

Key data: 300 mm, 600 mm

Iddon 24inch (600mm) x 12inch (300mm) Two Roll Mill Chilled cast iron rolls Rotary joints Right angle drive Radicon Gearbox Fulton Rotary joints AEI electric construction motor Safety bar back and front of mill

Key data: 150 mm, 300 mm

Two Roll Rubber Mixing Laboratory Mill Manuf.: JRD Bipel 300mm x 150mm rolls Roller type bearings Nip fully guarded Motorised nip adjustment Roller speed variable up to 32 rpm Friction ratio 12:1 Grease lubrication Roller reverse system

Key data: 650 mm, 2100 mm

W&P 2100mm (84”) x 650mm (26”) Two Roll Mill Manufacturer: Werner & Pfleiderer Periphery drilled rolls Both rolls smooth Roller bearings Individual motors driving each roll (2 motors) Variable friction and nip Hydraulic nip Knife cutter under roll Nip guides on top of Mill 1 piece bedplate Compact design Fully rebuilt and refurbished by Dewiko Germany in 2001

Key data: 1000 mm, 450 mm

Comerio Two Roll Mill 1m (40”) wide x 450mm diam. Motorised nips Tray fitted beneath Mill rolls Motor mounted beneath roll AC 3-phase 400V Complete with Control Panel

Stock # U2267-2 Second hand stainless steel contact parts (316Ti) sand mill by Drais (Germany) model Perl-mill PMC 12.5 TEX. Machine has total volume of milling chamber 17.2 l and working volume about 12 l. Mill has rotor with plastic rings and works with rotation speed up to 1450 rpm. Machine is driven via belt gearbox by electric motor 13.5 kW, 1500 rpm, 400 V, 50 hz, Eex eIIT3 design. Mill is equipped with feeding pump, filter and electric cabinet. Includes technical documentation. Machine new 2002.

GINES, Barcelona 800mm wide x 350mm dia two roll mill, Machine number: 88, manual nip adjustment, adjustable guide plates, friction ratio 1:1.18, direct drive gearbox (on left hand side), with 60HP DC variable speed motor, Mentor II DC drive control panel. O/a dimensions 2750mm x 2100mm.

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

Hammer mill Manufacturer: NEUE HERBOLD Type HM 450/300 Working width: 300 mm Rotor width: 450 mm Drive: 18.5 kW -NEW MACHINE- size reduction of brittle plastics like electronic scrap, wood scrap, and organic insulation material.

EUROLUX Fruit and vegetable mill with grinding ring Delivery date: approx. 6-8 working weeks/ by appointment Description of the machine: With this mill system it is possible to shred a wide variety of raw materials, adapted to the pressing system and the degree of maturity. The raw material is placed in the funnel of the mill. There is a screw in the hopper that conveys the raw material to the grinder. The raw material is crushed in the grinder and laterally conveyed out of the grinder. Depending on the material to be ground, different knives and grinding rings can be used. You can also change the grinding degree through the speed. If necessary, it is possible to overlay the grinding with inert gas The system can be easily opened and pulled apart for cleaning. The mill is completely assembled and wired on a frame. Two lip seals are installed to seal the grinder on t ...

Qty. 1 Second-hand skin pass mill Mfc.: Mannesmann Demag Sack Built: 1980’s Modernised in 1986 & 1993 Type: Duo Cold Rolling Mill – Non-Rev. Dia. 330 x 500 mm Material: Carbon steel, cold rolled and annealed Strip width: 80 - 470 mm Thickness entry: 4.0 mm Exit: 0.2 mm Decoiler Modernised in 1986 ID: 400 with segments 500 & 600 mm Spreading range: 370 – 420 mm Strip tension: 1300 – 65 daN Braking system: Generator Braking torque: max. 1300 daNm De-coiling speed: 2.5 m/sec. Coil cross section: 20 – 1880 mm² Coil weight per mm strip width max.: 10 kg Coil weight: 5.0 T Coil ID: 400 & 500 mm Coil OD: 600 – 1400 mm Roll dia.: 300 – 330 mm Roll length: 500 mm Roll force: 1850 – 2400 kN Min. roll force: 150 kN Hydraulic roll adjustment Adjustment stroke: 80 mm Adjustment speed: 1 – 3 mm/sec. Rolling speed: 2.5 m/sec. (150 m/min.) PLC system: ...

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Manual nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 106kW DC variable speed motor. Very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible coupling, 2 x 68kW DC variable speed motors. Variable friction ratio/roll speeds. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 138kW fixed speed motor. Fixed friction/roll speed. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible couplings, 2 x DC variable speed motors. Variable friction ratio and roll speed. In very good condition.

Ideal for passage driving with consistent efficiency and for achieving the narrowest grain size distributions in the micrometer range, Maximum operational safety: even the basic version is designed in accordance with the explosion protection directive for installation in ATEX Zone 1 (ExII 2 G cb IIB T3) Grinding media sizes from 0.5–2.5 mm diameter Ideal cooling properties: The forced routing of the cooling water in the outer jacket allows the processing of temperature-sensitive productsEasy handling – each DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Easy handling – any DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Grinding tank : 50 litres Power : 45 kW Voltage : 380 V Weight : 1050kg

Milling machine 4-axis (15995740874) DMG Milltap 700 (2015) Spindle 24,000 1/min NC parts apparatus Lehmann EA-510. L Tool magazine 25 places Renishaw Measurement Kit Rinsing gun Milling machine 5-axis (15995747284) DMG Milltap 700 (2015) Spindle 24,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Rinsing gun Renishaw Measurement Kit Milling machine 5-axis (15995765944) DMG Milltap 700 (2018) Spindle 10,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Renishaw Measurement Kit Automatic front door Automation interface including automation door on the right Milling machine 5-axis (15995734744) + WH3 (770200062R) DMG Milltap 700 (2014) Spindle 10,000 1/min Swivel rotary  ...

Various millstones

Two Roll Mill 1m wide Hydraulic Nips With motor and gearbox AEG motor, 380volts, 107amps, 55kw, 1475rpm, 50 cycles Unidrive Gearbox manuf: Santasalo, Type 3KSV70, Year 1977, Weight 1500kg Lunn Safety gear fitted front and back of Mill Complete with control panel All mounted on a one piece bedplate Compact

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

KAAST Millex VPlus 7 CNC machining Centre way back in 2011 complete with Siemens Controller 802S

- workpiece diameter d680 - max workpiece length 3400 mm - max working lengths 2600 mm - with discs (d1100 mm) - required electric capacity 60 kW/h - under power, in use

Bead mills Manufacturer: Bachofen AG (CH) Type: Dyno-Mill KDL-Pilot 3 items on stock No.: 1) 910969; 2) 860739; 3) 840338 Power: 3.3 kW in Eex protectioin very good condition with various spare parts LWH: 650 x 500 x 500 mm

Stable milling machine - Made in Taiwan - New - unused 3 Axis Digital Display - Heidenhain Scales Electronic handwheel for driving machine ashes by hand Tool spindle vertical and horizontal Tool holder steep taper 50 Max. spindle speed 1,600 rpm Travel X 1100 mm Travel Y 720 mm Travel Z 780 mm Table clamping surface 1500 x 450 mm Max. workpiece weight 1000 KG Rapid traverse of the machine axes 6000 mm/min Infinitely variable axle feed can be adjusted via potentiometer Coolant system Chip protection on the router table

Laboratory bead mill Manufacturer: Bachofen AG Type: KDL No.: 920235 Power: 1.85 kW in explosion protection shear tools in ceramic very good condition with various tools and spare parts LBH mill: 650 x 650 x 520 mm LBH box: 600 x 400 x 430 mm

Drive : 75 KW Dimensions : L 3800 mm x W 1600 mm x H 2200 mm Weight : 3900 kg.

Drive : 110 KW Dimensions : L 2500 mm x W 1300 mm x H 1800 mm Weight : 2800 kg

Qty.1 Second-hand milling (scalping) line Mfc.: Torrington Type: 30" Slab Miller Strip width: 30” – 762 mm Cutter Speed: 500 rpm Metal speed: 18 fpm (1.9 m/min.)) Capacity: min. ¼” max. 1-1/4” Thickness Entry thickness range: 13 – 20 mm

CNC Manufacturing Center Mill 2000 Commissioning 2007 4 - 5 axis machine Siemens 840 D Commuting X axis 2000 mm y axis 500 mm Z axis 550 mm 40 tool slots Rigid table with chip tray Clamping surface 2600 mm 550 mm with 3 T-slots High-speed package Rapid traverses 60 m/min Speed 20 - 12,000 rpm Coolant pump 30 bar 900 liters 2 extraction units as air purifiers Automatic grease lubrication 2x Rinsing gun Single-shift operation Spindle has been renewed and much more. The machine can be viewed under power

Stock number: 3922 PROCESSING Manufacturer: EMCO, Type: MILL E-600 Machines NO.: M-06204707, Year of manufacture: 2007 Specifications: Table size 700 x 500 mm Large table load 500 kg Longitudinal movement (X) 600 mm Transverse movement (Y) 500 mm Vertical movement (Z) 500 mm Size distance spindle/table 700 mm Spindle cone 40 iso Stepless spindle speeds 10000 rpm Total power 16 KVA Tool changer 20 places Control Fanuc Oi-MC Fabr. Controlled in axes 3 Operating hours spindle 3167 hours Accessories: Cooling by spindle Chip conveyance. Cooling water system. Length: 2040 mm, Height: 3000 mm, Width: 2500 mm, Weight: 3800 kg

We offer a Milling Machine Routing Star V that is an ideal choice for automotive component machining and other high-precision tasks. We have four machines available from different years ( 2012, 2014, 2017) Technical Data: Dimensions (L x W x H): 5600mm x 2990mm x 2950mm Weight: 8000 kg Power Rating: 12 kW Connection Power: 3 x 400 V, 50 Hz Hydraulic Working Pressure: Max (bar not specified) Pneumatic Working Pressure: Not specified Table Size: 1400mm x 700mm Table Type: Rotating Table Number of Robots: 2 Tool Changer: Yes Find more here - / Contact us at -

Exchange units for contour milling HOMAG

quill dia 110 mm quill stroke 100 mm ISO 40 (DIN 2079) 360° swiveling of the spindle head previously used on Hermle UWF 1000

Key data: 500 mm, 200 mm

Drilling / Milling machine OPTIMUM type OPTI F 40 E Travel X: 500 mm Travel Y: 200 mm Spindle: Ø 80 mm Cone CM3 Spindle exit: 120 mm Spindle speed: from 95 to 3200 RPM Table size: Length 730 mm x Width 210 mm 2 speeds motor Motor power: 1,5 Kw Straight head Cross table Manual Descent Equipped with: 1 rotary vice Voltage: 380 V Dimensions (L x W x H): 1200 x 900 x 1400 mm Weight: approx 350 KG

Travel X/Y/Z: 406mm/305mm/254mm, table dimensions X/Y: 914mm/305mm, max. table load: 227kg. Spindle speed: 6000rpm, tool holder: BT40, tool positions: 10, rapid traverse X/Y/Z: 15.2m/min. Machine dimensions X/Y/Z: approx. 2350mm/2300mm/2700mm, weight: approx. 1550kg. Including an additional control panel on request (not included in the price). Documentation available. On-site inspection is possible.

GeneralHighly productive compact machining centres; Control: Siemens 840D solutionline Technical DataFeed rate longitudinal/transverse/vertical1-60000/1-60000/1-60000 mm/minRapid traverse longitudinal/transverse/vertical60/60/60 m/minWorking area 1Longitudinal700 mmCross420 mmVertical380 mmMiscellaneousClamping SystemMAS 403 - 45° Floor space/WeightDimensions (L x W x H)1,65 x 2,34 x 2,5 (1,65 x 2,95 x 2,55) mWeight approx.4100 KgSpindle speed up to 24,000 r.p.m. BT30Spindle 24,000rpm with tool taper BT30 JIS B 6339 (MAS 403-45°) AC-Motor 20 / 4 KW (max. / 100% ED) Watercooling Spindle and Spindle motor via heat exchanger (fan)TableTable surface 840 x 420 mmMaximum load (table centre) 300 KgSlot width 14 mmNumber of Slots 2Clamping grid M 12, 100 x 100 mmTool clamping for BBT 30 (Big+)Tool taper BBT 30 - Big+ Pull stud MAS 403 - 45°Tool magazine 25 placesTool magazine 25 places (suita ...

Manufacturer: RASOMA Type of Machine : End Milling Machine Year of Manufacture: 2018 Total Weight: 16,000 kg Voltage: 3x400V, 50Hz Control Voltage: 24V DC, 230V AC Rated Current: 92 A Maximum Fuse: 125 A Power Rating: 62 kW Find more here - / Contact us at -

Key data: 1000 mm, 500 mm, 530 mm

Like new: X-axis: 1,000 mm Y-axis: 500 mm Z-axis: 530 mm Table dimensions: 406 x 1,372 mm Spindle mount: BT 40 Spindle speeds: 1 - 8,000 rpm Control: Fagor Equipped with: - Coolant system -Operating instructions Country of origin: Taiwan Engine power: 10 hp Machine LxWxH: 2,900 x 2,280 x 2,550 mm Machine weight: 3,100 kg

Notching cutter Comall Type: Mill One