hot filling line used for sale

PRE-ALPINE REGENERATION LINE COMPLETELY REVISED, ELECTRICAL WIRING, VENTILATORS, PULPIT. EQUAL TO THE NEW! MATERIAL: PE PP PC PS ABS HOPPER WITH DOSING UNIT EXTRUDER WITH DIAM SCREW. 105 MM. 35 L/D AVERAGE PRODUCTION 300/450 KG/H BASED ON MATERIALS ENGINE: 117 KW OIL PUMP VACUUM DEGASSING PUMP centrifuge Cabinet

CALIBRATION TUNNEL COOLING TUNNEL LOADING TUNNELS EQUIPPED FOR DIAM TUBES. 20 TO 160 MM HOURLY PRODUCTION: 280-300 KG/HOUR

Used thermoforming roll line by Tepro, model LPP 420-30/3618. New: 2014. Machine serviced, very good condition. Technical data: Machine stroke mm 300 Forming chamber mm 282x356 Pressing depth mm max. 130 Filling field length mm 900 Distance between tools mm 1800 Efficiency cycle/min 4-12 Vacuum pump m3/h 100 Power supply V/Hz 3x230/50 Power kW ~ 13.5 Compressed air pressure bar min. 6 Cooling water consumption l/min 8-15 Compressed air consumption Nl/cycle 100-150 Width of the upper foil mm 420±1 Bottom foil width mm 420+2 Max. bottom foil thickness (soft / hard) mm 0.3 / 0.6 Max. bottom foil diameter mm 400, sleeve 76 Max. top foil diameter mm 400, sleeve 76 Weight kg ~1300

Production line for the mannufacture of sacks for cement and building material, consisting of one universal tuber 981, Gartemann + Hollmann, and two valve sack bottomers 525, Gartemann + Hollmann

Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K Thermoformer with auto-start facility Indramat Servomotor Indexing Top & Lower heaters Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump. Inline ILLIG ÜG70B Counter/ Stacker, with delivery conveyor Inline Grinder

- MWM Mixture Pipe - Please note! Price per piece! - 12141922 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new technologies and processes into our opera ...

- Mixture Pipe Mixture Pipe MWM 12301431 Original - Suitable for several motors - Please note! Price per piece! - 12301431 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting ...

Qty. 1 Second-hand baby diaper production line Mfc.: Maqmantas Type: Pannolini – 50 IMD Built: 2015 Size of diapers: Mini, Midi, Maxi, Junior Nominal Production: 50 pieces/min. Dimensions: 4800 x 950 x 2050 (L x W x H) mm (without exhauster) Room dimensions: 21 x 5.3 x 3.1 m – L x W x H Voltage: 3 ~ 220 V, 3 ph., 60Hz, 100 A Power: 12 kW Theoretical Weight: 1500 kg Screw compressor: 7, 5 bar The machine can be demonstrated in running conditions.

Used packaging line for capsules into jars made by Pharma Packaging Systems/Robak company PPS capsule counter - 2 pcs Manufacture year: 2015 Production country: England Max capacity: up to 14 op / min capsules of 000 in the amount of 300 pcs up to 80 op / min smaller quantities Counting range: 10 - 300 items Possible packaging: cylindrical jars 150mm in diameter and up to 210mm in height Labeling: self-adhesive wrapping labels Codification: InkJet on the bottom of the packaging Required media: en. electric, compressed air

- Inletpipe intake line MWM 12302410 - Suitable for several motors - Please note! Price per piece! - 12302410 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integra ...

- Mixture pipe MWM 12301623 - Suitable for several motors - Please note! Price per piece! - 12301623 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new t ...

- Mixing pipe mixture line MWM 12301281 - References: 12300476 ; 12300650 - Suitable for several motors - Please note! Price per piece! - 12301281 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new proje ...

1 x 'Forward Machinery Industrial Corp'. (Taiwan) 4 roll inverted L calender line, Year of manufacture: 2007, Roll dimensions: 34in (860mm) dia x 157in (4000mm) wide, Peripherally drilled (oil heating), Roller bearings, Motorised nip gap adjustment, Roll bending rolls 2 and 4, Cross axis roll 3, Independent drive to each roll:- Roll 1: 110kW, Roll 2: 150kW, Roll 3: 150kW, Roll 4: 110kW. Finished product width 3600mm. Pick off rollers, Matt finish embossing station, Edge trimming, 19 x cooling drums 355mm dia x 4000mm wide, Dual station surface winder. The line is already dismantled and ready for immediate shipment. There is also upstream equipment available by separate negotiation (high speed mixers, 2 x 100L Banbury, strainer, two roll mills etc).

REF-0 FELTRACON LEMON PROCESSING AND SLICING LINE Line for cutting lemons into slices and half slices Manufacturer: FELTRACON Model: FC3281-S03 Year: 2006 Throughput: 750 kg/h (depending on the type of product) Product temperature: 5-20 °C. Composed of: 1) Accumulation elevator conveyor: Voltage: 220/380 V+PE [50 Hz] Rated power: 0.25 kW Rated speed: 0.087 m/s Overall dimensions: length 2,620 mm; width 1,750 mm; height 2,300 mm Belt effective width: 360 mm Net weight: 350 kg approx. Accumulation hopper: 200 litres (max.) 2) Cutting head with feed conveyor: It cuts the lemons into slices, while both ends of the product are discarded. Voltage: 220/380 V+PE [50 Hz] Rated power: 0.75 kW Max. product feed (including fallen pieces): 180 pcs/min Usable lemon dimensions: 42 mm Slice thickness: 7 mm Overall dimensions: length 1,750 mm; width 1,050  ...

VOORTMAN V630 + HS540 beam drill line was built in the Netherlands. An easy-to-use machine with wide machining capabilities, allows to significantly increase the productivity of any industrial plant by fully automatic drilling, countersinking and threading of metal workpieces. All of this while maintaining low operating costs, high productivity and excellent precision. The VOORTMAN V630/1000A beam drilling machine consists of the following parts: – VOORTMAN V630 drilling unit – PEHAKA HS 540/1100 GBS band saw – roller conveyor The production line uses top-quality components from renowned brands to reduce size deviation tolerances and improve the quality of the final product. These include among others drilling heads with automatic 6-position tool changers for drills for various types of workshop work. During machining, the profile is fed to and from the workstation on a sp ...

Make : Roversi Tank Volume :3000 liters Cream Capacity : 1000 Litres to 1500 Litres Double jacketed Kneading Rolls inside the barrel Control panel Stainless steel production area Skid Mounted 2 Door Safety closer See through glass Fully Refurbished on order Manufacturer Roversi Model 3000 L

Unwinding reel / decoiler â?¢ Bandwidth / strip width max. 1,500 mm â?¢ Tape thickness / strip thickness (430 N/mm2) 0.5-2.0 mm â?¢ Coil outer diameter / coil outer - 1,300 mm â?¢ Coil inner diameter / coil inside - 470-520 mm â?¢ Coil weight / coil weight 10,000 kg â?¢ Side shift / side shift . . . . . . . . . . . . . . . . .

suitable for standard crumbs all stainless steel belt width 400 mm with air knife 2,4 kW adjustable speed mobile with outfeed belt dimensions (l x w x h) : ± 2.250 x 950 x 2.300 mm

-with 2 flour spreaders -Total length 680cm -with rollers

Saw for Pipe Cincinnati RS 25 PZ S 1992 year 4000 Euro

H.E.F. HEF DURFERRIT salt bath nitriding line was built in 2001. This highly advanced production line makes it possible to improve the mechanical properties of the workpiece by increasing its strength and resistance to wear and corrosion. To achieve this, the workpieces undergo thermo-chemical treatment in the form of salt bath nitriding, which results in an anthracite or black colour and a surface hardness of up to 1300 HV. The H.E.F. HEF DURFERRIT thermo-chemical treatment line has been continuously serviced and upgraded throughout its service life. About 2.5 years ago, the lining and heaters were overhauled and the main nitriding ladle was replaced. It is also possible to purchase a new spare main ladle for the offered machine at an additional cost. The production line includes: – a ladle for washing/rinsing workpieces (3 pcs.) – plunge pre-heating furnace – SURSULF nit ...

Juice Preparation Plant – Tetra Pak Processing System Complete juice preparation and pasteurization plant designed for the production of fruit juices and beverage bases. The system includes Tetra Almix Spark, Tetra Alblend Spark, and Tetra Steridrink pasteurization equipment, providing reliable mixing, blending, and thermal treatment for industrial beverage production. A) Tetra Almix Spark 020V - High-performance mixing and dissolving system used for preparing beverage bases and ingredients before blending or pasteurization. General Information - Manufacturer: Tetra Pak - Model: Tetra Almix Spark 020V - Year of Manufacture: 2001 Capacity - Production Capacity: 0 – 15,000 l/h Installed Options - Vacuum cleaner - Drum emptying station - Utility Requirements - Sealing Water - Connection: 1/2" - Capacity: 700 l/h - Temperature: 15°C - Pressure: 0.3 bar ...

Complete Veneer Peeling Line Working Length: 3300 mm

Sheet thickness aluminium: 1.00 mm Due to the bevel cut, the X-Cut machine can not only cut straight strips in the longitudinal and transverse directions, the automated bevel cut opens up many new possibilities for cutting the different surfaces quickly and accurately. Saves up to 90% of the time Up to 60 degrees angle adjustment in both directions Intuitive operation thanks to touchscreen and calculation aids Thanks to optimized software, cutting trapezoidal surfaces, triangular surfaces and other surfaces for standing seam roofs and wall cladding is no problem Due to the fully automated bevel cutting and the versatility and accuracy of the software, a high level of time savings can be achieved during production in the company and also during installation on the construction site Automatic operation: Enter the desired length and the number of pieces to be cut automatically. Tota ...

QTY. 1 SECOND-HAND PASTA / NOODLE PRODUCTION LINE – FOR SHORT AND LONG PASTA Mfct.: Macri (Italy), Braibanti (Italy); Capacity: approx. 260 kg/h; Built: 1990 & 2000, Status: still on foundation, stopped in 2022 General description: The pasta factory currently works with 2 x 160 Kg/h presses, one for long pasta and one for short pasta. The drying capacity of each dryer is +/- 500 kg. To fill them all it takes +/- 15/16 hours, i.e. two work shifts. Required area: 805 sqm., approximately L x W x H = 35 m x 23 m x 7 m Consisting of: 1 Automatic frame stacker 2 Stacker with protective grilles 3 Entry of frames into stacker 4 Idem 5 Entrance of the frames into the shaker 6 Frame loader 7 Entrance Long pasta packaging - Tonelli spreading machine with mushroom. 8 Tonelli spreading machine with mushroom - Long pasta packaging 9 Entry Packaging of long pasta 10 Group of 6+3  ...

Qty. 1 Second-hand Dedusting and air filtration system – currently used for an aluminium foundry – can be used for other applications Mfc.: NEOTECHNIK Gmbh (Germany) Built: 2006, Modernised: 2015 Currently used in an aluminium foundry, can be used for other applications Consisting of: 1. Main filter, chamber 1 2. Main filter, chamber 2 3. Main air fan for cooling, Reitz Germany, 1 4. Main air fan for cooling, Reitz Germany, 2 5. Installation for limescale dosing and dust separation 1 6. Installation for limescale dosing and dust separation 2 7. Cyclone 1 8. Cyclone 2 9. Silo for limescale 10. Dust collecting unit 1 11. Dust collecting unit 2 12. Auxiliary equipment, such as piping, valves, ducts, fans, additional filters, etc.

Without Extruder Complete Line for Pipes 63-140 mm Reifenhauser only 20.000 working Hour // very good condition consist of following elements ; 1. Vacuum sizing tank Reifenhauser KKE-R 0125 nr. 70057 2. Cooling tanks Reifenhauser KE-R 0125 /6000 nr. 70058 3. Cooling tanks Reifenhauser KE-R 0125 /6000 nr. 70058 4. Cooling tanks Reifenhauser KE-R 0125 /6000 nr. 70058 5. Pipe pulling device Reifenhauser A-R 0075 nr. 70059 6. Saw for Pipes Reifenhauser TSQ-R 0075 nr. 70060 7. Marking Machine Medek & Schorner FMS 2R-U nr. 758.45

2000 Ltr Roversi butter Churn Double jacketed to avoid the hiumidity, see-through glass, fins inside the churn to brake down the butter and control panel self mounted. Make: Roversi Tank Volume : 2000 ltr Cream Capacity : Min 500 Litres To 1000 Litres Double jacketed 1 Door with safety closer See through glass Stainless steel production area Hzjsulook Skid mounted VISIT & INSPECT : DERBY UK, DE24 8HL , UNIT 6 ,Dairy Machinery UK Site.

Used complete technological line for slaughtering pigs with a capacity of 80 pcs/hour The line consists of the following components: DIRTY PART - Feed pass 1.8 mb with spray and blocking - Restrainer box for BO-4AT deafening - Bleeding tub with rollers 4.5 mb - Conveyor mobile bleeding table - Consumable blood collection device UZK - 2 Z - Differential lift for bleeding track - Synchronizer - Three-shaft brush washer - Self-exuding loop lowerer - Self-pulling loop washer - Photo-cell sink - Single station knife sterilizer - Apron rinser - Hanging scaler 80 pcs/hour heated with steam - Loop extractor - Gantry sealer Super B 80 pcs/hour - Bristle conveyor belt 7 mb - Bath under the bristle brushing machine. - Hood over the bristle scalding set - Exponential table for brushing machine with air curtain - Tubular cleaning table - Bath under the  ...

Wooden flooring line consisting of: Motorized loading roller conveyor Suction cup loader Sliding table saw/panel saw Multi-blade panel saw Tipper Dry or glue-fitted slats Stackers Packaging machines Parcel loader Packaging Automatic pallet unloading strapping machine Camera-guided movements The loading roller conveyor, the stack (max 50 sheets, thickness 8mm) is transported under the suction cup loader, where the panels are picked up and placed on the hopper of the panel saw. Model:TSA 360A The sectioned sheets go on a 90° sideshift and are conveyed by belts over a suction cup feeder. Here, by means of a camera, by means of the black line, they are centered and introduced into the Paul K34G multi-blade panel saw/multi-blade Paul The sectioned slats (n°10 size 130 size 1300x2x20202) go on a 90° sideshift that transports them to an octagonal tilte ...

Hollow-chamber plate system Material: PC, PP Extruder: Breyer Screw diameter: 120 mm, L/D: 33 Engine: 200 kW with degassing, Siemens "Simatic OP17" PLC control, vacuum station with water ring pump and condensate pots, sieve changer Gneuß SF75, melt pump Maag 56/56, calibrator OMIPA 2400 mm, 10-fold multi-roll extractor OMIPA, 2 roll extractor OMIPA, protective film laminating station, hot-knife longitudinal separation, OMIPA cross saw 2400 mm R

Linear drive, stroke 420mm, DGPL-80-420-PPV-A-KF-B, 161797, Festo, used tested Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Used and tested! The part was purchased from a spare parts warehouse of a company, was tested by us and checked for leaks. Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the seller, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclude warranty claims of the buyer for improvement, exchange, subsequent delivery or also for updating in case of digital components. Also excluded is the liability for direct and indirect consequential damages. Our terms and conditions appl ...

Qty. 1 Second-hand bonder line Bondern is a process for the surface treatment of metal surfaces and for producing a conversion layer by phosphating. It serves to protect against corrosion. In further processing steps such as deep drawing, the phosphating created serves as a sliding layer. Mfc.: TBA Built: TBA Strip width: 250 – 600 mm Thickness: 2.0 – 4.0 mm De-coiler ID 500 mm OD 600 – 1900 mm Coiler ID 500 mm OD 600 – 1580 mm Plating Double sided: 1.0 – 4.0 g/m² Single sided: 2.0 – 5 g/m² Note: 3 g/m² = approx. 2 µm layer thickness

Qty. 1 Second-hand JCO pipe press bending line Mfc.: Samyul, ROBO, Shinsung, ChangSong, Rotech, FANUC, Hyupshun, Ingersoll Built: 2003, 2008, 2009, 2013, 2014 Plate material: Mild steel Plate dim.: 16.0 x 5.2 x 0.08 m – L x W x T Pipe dia.: Φ400~Φ1650 mm Pipe Length: 6.0m ~ 16.0 m Scope of supply: JCO Hydraulic Press Tack Welder Machine Sealing Welder Pipe Heating & Rotating Device Inside Welder Outside Welder Calibration Presses Milling Cutter Cutting Machine Bevelling Machine Compressor

CAPE nailing line, year 2002, CE standards, consisting of: N° 1) hydraulic belt nailer model CP HO 4200 - 7 m long carpet - with n° 24 pliers - max nail height 120mm - hydraulic power unit - installed power 20 kw N° 1) FANUC robot model M-410 HS with suction cup system for loading material to be inserted into the nailer (installed in 2022) N° 1) aligner transfert N° 1) stamping machine with 4 moulds and relative transfers N° 1) rotary swivel for pallets N° 1) stacker stacker N° 1) Warehouse shutter for pallet rows N° 2) electrical panels with line control and programming display Total length of the line about 40 meters Used line visible installed and running

FISH FOOD / PET FOOD EXTRUSION LINE CAN HAVE MANY APLLICATIONS FROM PET FOOD TO FISH FOOD was used to produce dog food output till 2 / 3 tonnes according to formulas Extruder was well maintained MODEL BC 82, TWIN SCEWS, has rails allowing to open totally the extruder to clean screw and barrels Extruder main electric cabinet coming with the line Conditionner Wenger , stainless, model 7 DCC , new in 2000 used for 2 years extruder main electric engine new in 2000, Continuous current LAK 4180 DA 400 volts, used for 2 years pelleting device, sieve, scale, buffer bin, STOLZ coater, STG 500 with vacum pomp the cooler (STOLZ RCC SEP 22X22F ) is not any included in the line many accessories, pomps, valves are coming with the line The line is partialy diassembled, plans could be provided Visits can be planned, enquiries for further details are welcome

PAGUS

Hyundai RB Onsan Factory, located at Ulsan in South Korea produces welded pipes by means of LSAW – Longitudinal Submerged Arc Welding process. The line is offered complete, featuring advanced HAEUSLER (Switzerland) core equipment. This facility is capable of producing welded pipes with the following specifications: Diameter: 22 to 80 inches Thickness: 6.4 to 25.4 mm Length: 6,000 to 12,200 mm The production line is equipped with a comprehensive suite of machinery altogether ensuring seamless and efficient production of LSAW pipes, including: • Plate edge milling • 3-roll bending • Post bending • Tack welding • Inside welding • Outside welding • Copander • End facing • Pipe inside washing • Hydrostatic tester • X-ray • Semi-correction • Pipe roll conveyor with skid system

Qty. 1 Second-hand full automatic mat and shine anodising coating line Mfc.: CISART Built: 2013 Stopped: Capacity: 1,800,000 pieces of profiles per annum Maximum Part Length: 3 m Requested area: approx. 630 m² Operators: 4 - 6 Estimated Full Power Consumption: 960 kW +/- 10% Voltage: 415 V, 50 Hz, 3 ph. Heat Consumption Max.: 500,000 Kcal/H +/- 10 % Water Consumption: 3 m³/h Water Consumption (TAP) by Customer: 10 m³/h Air Consumption: 1 m³/h Heating System: Electricity & Gas Acid Recovery System: 3 kg/h CHILLER 400,000 + 160,000 kCal/hr 40 °C Max. Ext. Temp. Water cooling range: 9-14 °C 190 + 80 kW Dozing System Quantity: 8 Eye & Body Wash Quantity: 2 Qty. 49 Tanks, 3.5 x 1.1 x 3.0 m – L x W x H Weight: 10 ton each Tank made of 2,5 mm thick AISI304 sheets

Used three extruders with die - head/three layer extruder from POLY TECH model HP 1800/3/100/55/55. New: 2000. 1) Head/Matrix - Slot of the die - 2,26 - Die diameter - 220 mm - Thickness 25-130 microns - Capacity 250-300 kg / hour 2) Matrix/Head - With efficient heating system (set of heaters with sensors PT/100 temperature sensors) - Three described Poly Tech extruders A) Extruder fi 100 mm L/D 30 with 150 kW motor drive . ZAMBELLO/ITALY drive gearbox TYPE RPU 280 E RPM 1400 B) Extruders fi 55 mm L/D 30 with 60 kW motor drive pcs. 2 ZAMBELLO/ITALY gearboxes TYPE RPU 180 E RPM 1400 The described extruders have a gravimetric system from DOTECO/ITALY Model GRADO IIS/GO 4100940 equipped with a metering system with computer readout on the measuring cabinet. Complete plasticizing systems including drive gears and main driv ...

Single-screw extruder • Type: 120/28 LD • AC Motor - 75 kw • Screw speed: 150 rpm. • Extruder cylinder: Air-cooled • Degassing zone Sieb changer • Strandhead Water bath: 4.5 m Granulator SG 200 Classic sieve Silo with conveyor fans: approx. 1m3

Stock# UG6311 Second hand line for production caramel candies, mono flavour. Line can produce fruit taste candies, mint candies or milk (fat based). Reporting output up to 468 kg/h. Line consist of: - Caramel mass preparation section - includes caramel cooker TC&C Process designers 24" Schlagenkocher, manufactured by Snelders, new 1997. Working output up to 1000 kg/h. - Winkler & Dunnebier forming line type 163.04, new 1997. Reported output up to 486 kg/h. Forming section has dimensions: 920 mm x 280 mm x 40 mm. Forming dies in motion - 118 pcs. Number of candies per one mold: 240 pcs. Machine works with speed up to 6.5 molds per minute. Working dimensions: L 11.85 m x W 1.9 m x H 2.83 m. Final product discharged at height 850-950 mm. Power consumption 40 kW

Tuna Packing and Seaming Line: A complete, automated system for tuna packing and seaming, composed of the following high-performance equipment: De-palletizer for Empty Can Feed: Efficiently separates and feeds empty cans for the packing process. View details Magnetic Elevator: Transports cans using magnetic technology, ensuring smooth and secure handling throughout the production line. View details Tunipack GFDC Tuna Packing Machine: Fully automated tuna packing machine, designed to efficiently pack tuna in a 150 mm format, ensuring optimal packing speed and precision. View details Hermasa Transporter with Brine Doser: A reliable transporter system, integrated with an automatic brine doser to ensure precise application during the packing process. View details Oiling Machine for Fish Canning: Specialized machine for the uniform application of oil to fish, enhancing the preservat ...

Micro-process-controlled line unifier for the automatic unification of multi-lane packs coming out of a packaging machine. - Package length adjustable up to 550 mm trigger length Original price in 2007: 17.00,00 € - Number of lines selectable from 1 - 6 tracks - Electric tool depth adjustment -Metrics: ESV 03 = Length 1560 mm / Width 610 mm - Stainless materials Low-maintenance assemblies result in a robust, high-performance system. A stand-by function ensures that all belts stop when no more packs come out of the packaging machine. This ensures that all packages on the line unifier are completely cleared and fed into the price labelling system.

In-line hole drilling machine Scheer DB 4 L x W x H: 1500 x 1500 x 1900 mm Weight approx. 1000 kg Built in 1980 1 aggregate vertically up 1 aggregate horizontal - vertically pivotable The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

The Continuous Galvanizing Line No. 2, built in 1985 and featuring equipment from IHI, Mitsubishi Heavy Industries, and Daido-EFCO, delivers high-quality galvanized steel for various applications. With a line length of approximately 228 meters and a production capacity of 144,000 tons per year, it efficiently processes low-carbon steel coils with widths ranging from 610 to 1,220 mm and thicknesses of 0.15 to 0.8 mm. Production ceased in December 2016. Equipped with a high-capacity furnace and air knife wiping system for coating control. The skin pass mill adds superior surface quality, while the tension reel provides consistent coil handling. Make: DAIDO-EFCO (Furnace) IHI (Galvanizing and Overall Equipment) MITSUBISHI HEAVY INDUSTRIES (Skin Pass Mill) Year of manufacture: 1985 Mothballed since: Ceased production in December 2016 Production capacity: 144,000 tons per yea ...

The Coil Preparation Line, built in 1987 by Sumitomo Heavy Industries, represents a robust solution for processing low-carbon steel with high accuracy and efficiency. This line delivered reliable performance for nearly three decades at JFE Steel's Keihin plant before ceasing production in December 2016. The equipment includes shearing, welding, straightening, side trimming, and tension control capabilities, ensuring precise coil preparation. Designed for a maximum speed of 1,100 mpm, the line efficiently supports a range of production needs. Make: SUMITOMO HEAVY INDUSTRIES Year of manufacture: 1987 Mothballed since: Ceased production in December 2016 Rolling direction: Right to left (right hand line) Line length: 33 meters approximately Processed material: Low carbon steel Strip width: 457 – 1,000 mm Strip thickness: 0.15 – 0.6 mm Coil inner diameter: 419 ...

According to description pdf attached complete line for profiles + WPC profiles

Originally commissioned in the 1980s, the Tandem Cold Mill at JFE Steel's Keihin plant undegone a significant modernization in 2007 to meet high standards. Upgraded with a state-of-the-art pickling line and carrousel tension reel, the 5-stand PLTCM integrates advanced technologies from industry leaders Mitsubishi, Hitachi, and IHI, enhancing the system’s reliability, productivity, and quality control. Make: MITSUBISHI-HITACHI-IHI Year of manufacture: 2007 (integrated to TCM from 1980s) Mothballed since: Ceased production in March 2019 Production capacity: 1,200,000 tons per year Rolling direction: Right to left (right hand line) Processed material: Low carbon steel Strip width: 600 – 1,350 mm Strip thickness: 1.8 - 4.5 mm entry 0.12 – 1.6 mm exit Coil weight: max. 32,000 kg entry max. 45,000 kg exit Line speed: 250 mpm PL section  ...

Merz KT160 semi-automatic packing line for packing sticks into pre-folded cartons , 2 lanes (previously the Merz was fed by two 1-lane stickpack machines), inserting of the sticks using 2 Stäubli robots (1 robot per lane), suitable for sticks with a width of 15 to 25 mm and a length of 60 to 100 mm, maximum possible carton size (pre-folded) 115 x 125 mm (WxL), count of 35 to 100 sticks per carton possible, capacity up to 63 sticks per minute, electrics 400V/50Hz/3.5kW, compressed air 6 bar, Siemens SIMATIC Touch Panel