126,606 used machines on RESALE, but how to find them? Machine Search
Stirred boiler / silo tank van der Molen 05-031/01, built 2006, in good used condition. Completely made of stainless steel, 2850 litres capacity, double-walled, heatable (steam), filling from above or with external pump from below possible. Dimensions B/T/H 190/160/420. Operating voltage 400 volts. More on request.
MontagePRESSE with central lubrication, pneumat. Feed and PLC control. Documents More info on request
Cold water high-pressure cleaner with 7.5 kW power 150 bar pressure and 30 l/min. Connection: 400 V; 50 Hz; 16 A Equipment: - Stainless steel frame - Powerful motor with long service life due to low speed - High pressure pump with brass cylinder head, all-ceramic pistons and stainless steel valves oil bath lubricated, low noise and vibration-free - Good handling due to pipe diameter of 38 mm - Ergonomically designed for good mobility - Very manoeuvrable to drive due to optimized device center of gravity - Chassis with solid rubber tyres - Crane lifting points - Lance holder on the left and right side of the device - Water inlet temperature up to max. 60° (standard) - Chemical suction as standard for devices up to 21 l/min at 200 bar - 10 m power connection cable, 16 A plug Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - HDP350 ...
AUTOMATIC BRIQUETTING machine type COMAFER DINAMIC 85N second hand machine volt. 380/50 CE mark : Yes briquett diameter mm. 60 production from 40 kg. to 85 kg. / hour motor power Hp 7,5 net weigth kgs. 850
Cold water high-pressure cleaner with 7.5 kW power 150 bar pressure and 30 l/min. Connection: 400 V; 50 Hz; 16 A Equipment: - Stainless steel frame - Powerful motor with long service life due to low speed - High pressure pump with brass cylinder head, all-ceramic pistons and stainless steel valves oil bath lubricated, low noise and vibration-free - Good handling due to pipe diameter of 38 mm - Ergonomically designed for good mobility - Very manoeuvrable to drive due to optimized device center of gravity - Chassis with solid rubber tyres - Crane lifting points - Lance holder on the left and right side of the device - Water inlet temperature up to max. 60° (standard) - Chemical suction as standard for devices up to 21 l/min at 200 bar - 10 m power connection cable, 16 A plug Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - HDP350 ...
Cold water high-pressure cleaner with 7.5 kW power 270 bar pressure and 15 l/min. Connection: 400 V; 50 Hz; 16 A Equipment: - Stainless steel frame - Powerful motor with long service life due to low speed - High pressure pump with brass cylinder head, all-ceramic pistons and stainless steel valves oil bath lubricated, low noise and vibration-free - Good handling due to pipe diameter of 38 mm - Ergonomically designed for good mobility - Very manoeuvrable to drive due to optimized device center of gravity - Chassis with solid rubber tyres - Crane lifting points - Lance holder on the left and right side of the device - Water inlet temperature up to max. 60° (standard) - Chemical suction as standard for devices up to 21 l/min at 200 bar - 10 m power connection cable, 16 A plug Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - HDP350 ...
Automatic baler Manufacturer: HSM Type: VK 4012 Year of construction: 2005 specifications: pressing force: 45 t Channel format: 720 x 900 mm (W x H) Setting: 4 x horizontal Filler: 1.000 x 650 mm Power: 22 kW with Superchargers Throughput capacity at 40 kg/m³ bulk density: maximum approx. 12.8 t/h Bale dimensions: approx. 720 x 900 x length (600-1.200) mm including funnel in special execution for the purpose of manual loading
Cold water high-pressure cleaner with 7.5 kW power 270 bar pressure and 15 l/min. Connection: 400 V; 50 Hz; 16 A Equipment: - Stainless steel frame - Powerful motor with long service life due to low speed - High pressure pump with brass cylinder head, all-ceramic pistons and stainless steel valves oil bath lubricated, low noise and vibration-free - Good handling due to pipe diameter of 38 mm - Ergonomically designed for good mobility - Very manoeuvrable to drive due to optimized device center of gravity - Chassis with solid rubber tyres - Crane lifting points - Lance holder on the left and right side of the device - Water inlet temperature up to max. 60° (standard) - Chemical suction as standard for devices up to 21 l/min at 200 bar - 10 m power connection cable, 16 A plug Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - HDP350 ...
Storage Tank / Beer Tank/ Pressure Tank in AISI 304 Operating pressure: 0,99 bar , Test pressure: 1,7 bar Material: V2A - AISI 304, 1.4301 Surface: inside and outside 2B=IIIC Top Bottom: with pressure lid 390 mm with 1 x thread connection DN 50 with 1 x overpressure valve with 1 x CO² connection with 6 x screws with 10 x reinforcing rings for better pressure resistance Lower Bottom: with outlet DN 50 with butterfly valve on 4 stable feets can be moved from all sides with a forklift / truck pallet Diameter: 1000 Total height: 1740 Zyl. Height: 900 Weight: 135
Steel pressure tank, enamelled (last content: fruit juice), operating pressure: 3 bar approx. 16.000 liters used - in very good condition UNI-KINN B-Nr. 19-801 GL Tank with vaulted bottom Operating pressure: 3 bar Measurment and Weight: Diameter: approx. 2.400 mm Total length: approx. 3.700 mm Weight: approx. 3 t on the top: 1 x air vent NW 50 on the front dished bottom: 1 x manhole 400 x 300 mm swiveling 1 x flange connection NW 50 1 x flange connection NW 40 as outlet Otherweise see photos
Cold water high-pressure cleaner with 2.2 kW power 150 bar pressure and 8 l/min. Connection: 240 V; 50 Hz; 10 A Equipment: - Stainless steel frame - Powerful motor with long service life - High pressure pump with brass cylinder head, all-ceramic pistons and stainless steel valves oil bath lubricated, low noise and vibration-free - Good handling due to pipe diameter of 25 mm - Ergonomically designed for good mobility - Very manoeuvrable to drive due to optimized device center of gravity - Chassis with solid rubber tyres - Crane lifting points - Water inlet temperature up to max. 60° (standard) - 10 m power connection cable - Automatic stop system Standard accessories: - 10m high pressure hose DN6, kink protection on both sides - HDP350 high pressure gun - High pressure jet tube with nozzle 030 Optional (additional cost): - Hose reel with 15 m hose The imag ...
To the fully automatic Assembly of frame parts. Frame dimensions: min. 120 x 120 mm 1050 x 2,500 mm 2 heating Rails
Cold water high-pressure cleaner with 15 kW output 380 bar pressure and 21 l/min. Connection: 3 x 400 V; 50 Hz or 3 x 460 V; 60 Hz.; 32 A Equipment: - Epoxy coated steel frame - Stainless steel cover - Compact, narrow chassis with stop function - Crane lifting device - Triplex high-pressure pump - Water inlet temperature max. 60°, thermal valve - Main switch with emergency stop function - Soft automatic start-up - Grid monitoring (phase control and undervoltage) - Connection cable 5.0 m with 32 A plug (50 Hz/60 Hz) - Water inlet filter Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - High pressure gun with isotube - Double jet tube and high pressure nozzle 030 Special equipment (included in the price): - Automatic start-stop with flow switch and switch-off delay 30 seconds - Water inlet filter 10" with sand filter insert and ...
EinspannmaÃ?e: 1600 mm x b: 2900 mm frame: 1600 mm x b: 2600 mm â?¢ Pression-Druck by 1T, self-locking, 140 mm â?¢ Versatility - many applications (frame, body, surface gluing) â?¢ Workload - ergonomic posture â?¢ Save time with user-friendly operation â?¢ Frame are bolted and therefore can be disassembled â?¢ Pressing units galvanized G & FE-RPW-3000PL
DYNAJET 500th HELI ATC RC INTRODUCTORY OFFER: If you want to be sure that this device is right for you, then we have a special offer for you: Crediting of rents for up to 6 months at 100% of the purchase price! For purchase: Including 1st UVV WITH arrival and maintenance (plus spare parts) on the same date (value approx. 1,500 net). The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner In addition to its user-friendliness, 500th with up to 500 bar working pressure is characterized in particular by its low weight, compact dimensions and high level of performance and safety. Construction 1-axle chassis with pneumatic tyres for easy manoeuvring on site Self-supporting and indestructible framework for weight optimization Crane eyelet for easy transport and handling Underrun protection for additional safety Frame in dip painting technology ...
Cold water high-pressure cleaner with 15 kW output 380 bar pressure and 21 l/min. Connection: 3 x 400 V; 50 Hz or 3 x 460 V; 60 Hz.; 32 A Equipment: - Epoxy coated steel frame - Stainless steel cover - Compact, narrow chassis with stop function - Crane lifting device - Triplex high-pressure pump - Water inlet temperature max. 60°, thermal valve - Main switch with emergency stop function - Soft automatic start-up - Grid monitoring (phase control and undervoltage) - Connection cable 5.0 m with 32 A plug (50 Hz/60 Hz) - Water inlet filter Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - High pressure gun with isotube - Double jet tube and high pressure nozzle 030 Special equipment (included in the price): - Automatic start-stop with flow switch and switch-off delay 30 seconds - Water inlet filter 10" with sand filter insert and ...
Hand spindle press to push pins in printed circuit boards 2 presses on a plate, with a dial indicator.
Make: Engel Type: Vertical Rubber Injection Model: ES 280V/40VT-ELAST Serial number: 41938, Year of manufacture: 2000 Clamping force 400kN Injection volume 280cm3 Platen size: 860x400mm In good condition.
CrimpOne C1-25sE Servo electric hose press with spindle drive Technical data Main technology: AC-servo ball screw Maximum pressing force: 250kN Crimping range: 10-54 mm Max tube size: 1¼ inch Master matrix D / l: 84 / 78 mm Servo motor: 5 kW Repeat accuracy: 0.01 mm Maximum opening: + 100 mm Maximum feed channel: 45 mm Maximum speed: 80 mm / s Maximum opening speed: 80 mm / s Max Crimpgeschwindigkeit: 10 mm / s Length: 1250 mm Width: 850 mm Height: 2100 mm Weight: 700 kg Control: TC12 - Omron touchscreen
Wood pelletizing plant, KAHL pellet press used the complex includes: Pellet press AMANDUS KAHL Matrice diameter approx. 1000 mm Pallet diameter approx. Ø 8 mm 5 Koller approx. Ø 340 x 130 mm Motor power 160 kW an auxiliary motor is damaged, but can be replaced by us Dimensions approx. 1600 x 1800 x 3000 mm + motor Weight approx. 8000 kg Conditioner / Dosing and Mixing Screw Diameter approx. Ø 400 mm 5.5 kW Dimensions approx. 3100 x 900 x 800 mm Single shaft paddle mixer Dimensions approx. 3300 x 1600 x 2000 mm + gear motor Pellet coolers Dimensions approx. 2300 x 2300 x 3000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
sed Manesty Rotapress MK IIA rotary tablet press, 45 station, double sided, with pre-compression, keyed upper punches, With feed hoppers, force feeders, controls and associated parts.
Hot and cold water high-pressure cleaner Working pressure: infinitely variable up to 500 bar Maximum requirement quantity: 14-30l /min Pump:3-Plunger,All-Ceramic Engine: Hatz,3-cylinder diesel (water-throated) Motor power:42kW Speed motor/pump: 2,350 /1,450 rpm Pump drive:V-belts Fuel consumption:approx. 5.3 l/h Volume fuel tanks:70l/105 l Volume water tank: 1000 l Pressure outlet:(water): M241.5 IG Heating capacity olburner: 291 kW (ca 95 °C) Consumption olburner: approx. 9.1 l/h Construction: self-supporting frame on frame with forklift pockets Empty weight: approx. 1,450 kg Mass: (LWH) 220+147177 Ground open (LWH) 307147246 Article no.: 1 491 030
Lefort / Corema lid press P400 TE for bale size 400x400 mm, press box 3 m length, opened 1.2 m wide, each wing 90 t and final compressor 100 t pressing force. Drive 30 kW Rexroth pump.
new
Cold water high-pressure cleaner Working pressure: 800 to 2,800 bar Required quantity: 8 to 27l/min Pump: Slow-running high-pressure pump with 3 carbide plungers, integrated reduction gear, compression lubrication and engine clamp Engine: VOLVO PENTA 4 CYLINDER Diesel,water-throated,5.200cm3 Engine power:160 kW,220 hp Motor/pump speed: 2,065rpm / 500 rpm Pump drive: Gearbox Fuel consumption:approx. 21 l/h Volume fuel tanks200l Volume water tank: 160l Volume urea tank: 25l Consumption urea: approx. 1.05 l/h Pressure outlet:(water): 9/16'' -18UNF LH IG or DYNAJET Easy Connect EC Chassis: 2-axle attachment Empty weight: 2.690kg Mass: (LWH)467197218 Ground open (LWH)487197254 Article no.: 1 610 040
With 48 filling valves 12head crown corker 12head screw capper
SMG DS 315-1500/1300 CNC hydraulic press was manufactured in 1984 in Germany. The machine, consisting of two interconnected stations, is used for pressing metal workpieces in manual, semi-automatic and automatic mode with a pressing force of up to 315 tonnes. All the machine’s machining parameters are set using a CNC control with a full-colour, touchscreen display. The press is equipped with a hydraulic and pneumatic sheet metal feeder, servo drives for feed rollers to set a very precise stroke of up to 0.1 mm, safety cages and workpiece feed and drop control sensors. The SMG 315 T machine underwent a complete overhaul in 2007, during which components such as pumps and safety installations were replaced. Technical data of the SMG DS 315-1500/1300 press - maximum press force: 315 t - working table dimensions (L x W): 1500 x 1300 mm - upper machine point (from the table): 750 mm ...
Number of punch stations 35 , output tablets 210,000/h , max. tablet diameter 13 mm , max. filling depth 18 mm , max. tablet thickness 8,5 mm , max. compression force 100 kN , max. initial compression force 20 kN , dieplate speed 15-100 rpm .
Mosca STF stowage clock conveyor; good condition; 1000mm length; 2 sensors; Speed adjustable. Mosca conveyor STF; good condition; lenght 1000mm; two sensors; I'm not.
For sale complete plant for wood pellet production, made from CPM, capacity 6t/h. A most of the maschines from line are produced in between 2008-2010.y., except presses for making pellets (its bit older then rest of the line, but completly renewed before restarting. Line is consisting from: 1.Chain conveyer for logs transport. 2.Lift with angle platform for dosing material. 3.Entrance belt transporter with magnetic section for detection of iron. 4.Grinder (hammer mill) BRUKS 500kW 5.Verticaly basket transporter for chip wood. 6.Horisontal belt transporter for chip wood with three side ejectors into depoos (separated with type of the wood) 7.Hidraulic floor platform for dosing wood chips (three pcs.) with all instalation and system of hidraulic pistons. 8.Horisontal belt transporter for transportation material on drying. 9.Repler transporter for driving wood chips into fire plac ...
L 45 Kw POWER 680 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw
Rotative tablet press of 27 stations Max. diameter of the tablet 16 mm Filling depth 18 mm Pressing capacity 80 Kn Prepressing capacity 20 Kn Production from 48.000 to 100.000 h Dimensions : 1.000 x 950 x 1876 . Weigh 1850 Kg. Force feeder Type of tool : B
Sparkling Pressure Tank / Sparkling Cooling Tank / Steel Pressure Tank Agitator Tank / Storage Tank / Pressure Tank with red food safe munkadur coating with cooling jacket and with isolation STANDING with new KIESELMANN sparkling pressure fitting Operating Pressure: 8 bar Volume: 5.750 Litre Measurement and Weight: Total Height: 4400 mm Tank Body Height: 3325 mm Diameter: 1600 mm Weight: 2110 kg Uni 3750 Operating-overpressure: 8 bar, Test pressure: 10,5 bar Operating pressure cooling jacket: 2 bar, Test pressure: 2,6 bar Inspection book, Dokumentation available Tank-Description Container with torispherical bottoms. Jacket and walls 9 mm. On cylindrical part of a cooling jacket as double jacket about 2.500 mm high. Container outside approx. 100 mm isolated, with screw stainless steel metal cover. Tank upp ...
L 30 Kw POWER 450 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 30 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw
Number of punch stations 55 , output tablets 594,000/h , max. tablet diameter 13 mm , max. filling depth 18 mm , max. tablet thickness 8,5 mm , max. compression force 100 kN , max. initial compression force 20 kN , dieplate speed 15-90 rpm . Dimensions of the machine : 1490 x 1230 x 2100 , weight approx. 3750 Kg
SINO NCP 160 eccentric press built in China in 2018 by Sino Machinery & Tools (Dongguan) Co., LTD. performs machining of metal workpieces with a press force of 160 tonnes. The machine is equipped with high-quality components, including e.g. a 100 mm adjustable slider making up to 25 to 55 strokes per minute, and a YU JAIV PDH-120 indicator displaying the distance of the die between the table and the slider. The large working area, ease of operation and outstanding precision, guarantee excellent machining results. The press offers the possibility of combining it with an automatic feeding system in order to increase the number of parts produced and significantly reduce costs. The total weight of the machine is 13 tonnes. Technical data of the SINO NCP 160 press - maximum press force: 160 t - work area dimensions (L x W x H): 910 x 600 x 410 mm - bolster dimensions (L x W x H): 125 ...
Briquetting press MATEC F-Cube 20 new Dimension press LxWxH: 130x74x112 cm weight 233 kg Briquette square 30x30 mm Capacity approx. 10-25 kg briquettes / hour Size feed funnel approx. 0.33 m3 Motor hydraulic pump 2.2 kW, 3x 400 V, 50 Hz Electricity consumption approx. 1.1 kWh How we work Continuous operation Year of construction 2021 Additional options: - Extension line for briquettes with stand -Auto. Start-stop system for operation with level monitoring - Sensors for level monitoring - Hydraulic oil 30 liters - 3 m cable with Euro plug 16 A - Flange adjustment filter-hopper press The spec. Density of briquettes is about 900 kg / m3. The maximum wood moisture content is 15%. The measured noise level is 62 dB. New machine, ready for operation. Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden ...
l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw
Tablet press Fette P2000 Tablet output: 250.700/h mechanical speed Number of station: 43 stations Tablet diameter max: 13 mm Compression force max: 80 kN Initial compression force: 20 kN Type of tool : EU Norm BB Height of the machine with filling hopper : 1950 mm Project floor area : 1212 x 1126 Weight: 2200 Kg Year of manufacture :1993
The press is for the re-pressing of bacon. This gives it a smooth surface Compressed air connection 8 bar
Dear customers, currently we offer a polystyrene press incl. shredder for sale. It is a new machine that has 0 operating hours! Here are a few more technical details: Material to be processed: EPS moulded parts and chips Maximum material density that can be processed: 18 kg/m³ Loading opening: 700 x 360 mm Filling height 1,402 mm Achievable compaction: up to 250 Kg/m³ System throughput: up to 15 kg/h Block dimensions: 130 x 130 mm Power supply: 3x400 VAC+N+PE 50 Hz Connected load: 1.5 KW, 400V 50Hz incl. automatic press pressure regulation with pellet holder Finish: RAL 7035 (light grey) combined with RAL 2011 (deep orange) Incl. water dosing system for direct screw cooling up to 10 litres/h with water shut-off valve. Price plus VAT, which will be shown separately on the invoice. Transport possible worldwide for an extra charge! If you have any questions, please d ...
Tablet output: 234.000/h (mechanical speed) Number of station: 37 stations Tablet diameter max: 25 mm Filling depth : 21 mm Die plate speed : 25 – 100 RPM Compression force max: 100 kN Initial compression force: 10 kN Type of tool : EU Norm D Height of the machine with filling hopper: 2135 mm Project floor area: 1260 x 1280 Weight: 2840 Kg
Pneumatic table pressbrand BoschYear 1985Maximum printing capacity: 40 kNMaximum stroke: 30 mmMaximum operating pressure 5 barCondition: usedMaetall table frame
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
N° of Stations 35 Output tablets per hour 70.000 - 210.000 Maximum tablet diameter 16 mm Maximum depth of fill 8.5 mm Upper punch entry 1.5 - 8 mm Die type B tooling Die diameter 30.1 mm Die height 22.22 mm Upper/lower punch length 133 mm Punch body diameter 19.05 mm Compression force 80 kN Power 3.75 kW Net weight 1143 Kg Can be also for doble layer.
maximum number of results exceeded
please refine your search
