128,269 used machines on RESALE, but how to find them? Machine Search
max. wheel diameter: 650 mm gear width: 200 mm max. module: 10 min. module: 1 work accuracy: DIN 6 clamping table diameter: 710 mm table bore diameter: 150 mm number of strokes - stepless: 35,5 - 560 c/min max. ram stroke: 230 mm feeds: 3,55 - 40 mm/min radial feed: 0,8 - 9 mm/min work-spindle diameter: 110 mm total power requirement: 28,2 kW weight of the machine ca.: 9 t dimensions of the machine ca.: 3,8 x 2,3 x 2,5 m Gear shaping machine for the production of spur gears, for Internal and external gears - Built under licence from LORENZ and identical in construction to LORENZ LS 630 complete Modernisation + overhaul in 2012 with: - new painting - new electrical system from Telemecanique - Counter Holder - Chip conveyor - Coolant unit - change gears Not used in production again after overhaul The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 600 mm y-travel: 400 mm z-travel: 400 mm spindle taper ISO: 40 spindle turning speed range: 80 - 4000 U/min transmission ratio: 18 feed range: 0,1 - 2000 mm/min rapid traverse: x = 4 / y = 3 / z = 5 m/min table load capacity: 250 kp voltage: 380 V / 50 Hz spindle drive: 5,5 kW total power requirement: 16 kVA weight of the machine ca.: 2,6 t dimensions of the machine ca.: 3,8 x 4,3 x 2,0 m • CNC-control system 432 E • Operating hours: 37719 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
; Gross weight [kg]: 1658; Engine: Cummins 6BTAA5.9-G12; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger, Including : sockets 125A - 63A - 32A - 16A; Water Tank Volume [l]: 185
3-channel foil nozzle EDS FSK-600 with flex lip (tire tubes) Output capacity: 40 -50 kg/h Lip adjustment with screws and storage beams in the main layer Film width: max. 600 mm Film thickness: 0.1 – 3.0 mm 3 computer-calculated hanger channels for optimal melt distribution Distribution: A 10-15%, B 70-80%, C 10-15% Drilled nozzle lip for liquid temperature control 9 heating zones with high-performance cartridge heaters Connected load for nozzle: 18 kW (0.5 kW x 36) Fully wired for 240 V / single-phase Nozzle dimensions (L x W x H): 450 x 650 x 400 mm, weight: 760 kg Coex adapter block for one middle and two outer layers Dimensions adapter (L x W x H): 320 x 210 x 400 mm Remark: Tool steel 1.2311 All flow surfaces are chrome-plated (25-30 μm)
turning diameter over bed: 320 mm turning diameter over slide rest: 220 mm turning length: 600 mm turning diameter in the gap: 320 mm turning speeds: 60 - 1650 U/min centre height: 160 mm spindle bore: 38 mm tailstock quill taper MT: 3 MK connected load frequency: 400 V total power requirement: 1,1 kW weight of the machine ca.: 340 Kg dimensions of the machine ca.: 1,4 x 0,75 x 0,7 m Center lathe with: 3-jaw chuck 160 mm. 4-jaw chuck 200 mm. Faceplate 200mm Fixed bezel Continuous bezel 4-way steel holder. Halogen machine light Chip tray, chip protection wall Hardened and ground bed tracks Longitudinal and cross feed Complete coolant system Forage protection Set of change gears Machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 630 mm y-travel: 560 mm z-travel: 560 mm Control: Heidenhain TNC 430 total power requirement: 26 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter: 630 mm turning length: 2000 mm control: Zyklen gesteuert steady: 2 Stk. total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Technical data for the workbench: Manufacturer: Dexion Type: Speedlock P90 Dimension: Width: approx. 1,665 mm Height: approx. 938 mm Depth: approx. 820 mm The scope of delivery includes: 02x Workbench stand, used Material colour: sendzimir galvanised Stand height: 900 mm Stand depth: 800 mm Stand profile: 100 x 100 x 3.00 mm Incl. cross and diagonal struts, base plates The stands are pre-assembled ( bolted truss ) 04x Workbench trusses, used Material colour: sendzimir galvanised Box profile: 89 x 50 mm Truss Type: SLO089|2 Clear width: 1,445 mm 08x Safety pins, used Design: completely galvanized 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,665 mm Particleboard depth: 820 mm Particleboard one-piece 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,425 mm Particleboard dep ...
The ASCO DS 600 is a compact, powerful double-shaft shredder designed for the efficient shredding of a wide range of materials, making it ideal for recycling companies, businesses, municipalities, and construction site logistics. With its robust construction and maintenance-friendly design, it handles wood, green waste, plastics, foils, pallets, packaging material, and production residues reliably and evenly. The counter-rotating shafts and powerful cutting units ensure controlled shredding with minimal space requirements. Its sophisticated design allows it to be used as a stationary or mobile unit, offering maximum flexibility for daily operations. An integrated control system provides simple operation, and an automatic reversing system prevents blockages for trouble-free use. Generous access points make maintenance quick and user-friendly. Whether used as part of a larger processin ...
sheet width: 3100 mm plate thickness: 6 mm thickness at Niro-steel: 4,5 mm daylight upper clamping: 100 mm Bending angle: 0 - 135 ° total power requirement: 7,5 kW weight of the machine ca.: 7,6 t dimensions of the machine ca.: 4,5 x 1,72 x 2 m Electric 380 Volt: manuel back gauge adjustable from the front: 70 - 600 mm Foot switch with emergency stop: Segmented upper tool: Oil filling: exklusive Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 120 kW weight of the machine ca.: 78 t dimensions of the machine ca.: 6100 x 5150 x 4300mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tool clamping area: 200x55x195 mm weight: 0,01 t - Multifix tool holder, 5 pcs. like new, 2 pcs. less used. --- price per piece ---- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
container volume: 600 l internal dimension: 1500 x 740 x 780 mm dimensions of the machine ca.: 1900 x 810 x 860 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The new powerful dry-running pumps: The ADH series is specially designed for solar developed for the demanding processes of the semiconductor and LED markets, With a suction capacity of 600-4500 m3/h. Semiconductors: High H2 pumping rate The performance of the ADH series brings the following advantages to the process: -ADL process performance: high pumping efficiency of light gases enables faster chamber emptying between process steps - Epitaxy and EUV: high pumping speed and high flow rate Tolerance meets the most demanding process specifications Adixen AD30K dry pump, high vacuum, AD 30 KL Manufacturer: Alcatel Adixen Type: AD30K.H Year of manufacture: 2008 Adixen AD100K.H Manufacturer: Alcatel Adixen Type: AD100K.H Year of manufacture: 2008 Vacuum pump: Manufacturer: AERZEN Type: GM 2000 CM-C Speed: 6000 rpm Voltage: 200-460 V Frequency (mineral oil/PFPE ...
x-travel: 6000 mm y-travel: 2000 mm z-travel: 3000 mm Control: heidenhain TNC 415 total power requirement: 34 kW weight of the machine ca.: 31 t dimensions of the machine ca.: 7000 mm m Stocknumber 1110055 Type of machine CNC Floortype milling machine Make ZAYER Type KCU6000 Build in 1992 Type of control Heidenhain TNC 415 X-stroke (mm) 6.000 Y-stroke (mm) 2.000 Z-stroke (mm) 3.000 Speeds (Rpm) 20 - 1.800 Admission in spindlehead BT50 Feeds X (mm/R) 5 - 5000 mm/min Feeds Y (mm/R) 5- 5000 mm/min. Feeds Z (mm/R) 5- 5000 mm/min. Rapid feeds 10.000 mm/min. Total Power (KW) 34 Lenght (mm) 11.000 Width (mm) 2.500 Height (mm) 7.000 Weight 31.000 Kg Additional information Juaristi MG6 turntable: 1500 x 1200 mm Cooling system: 2.5 Bar Tool cooling: 15 Bar The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
-Model Colatrice REL 600 -with digital foil keyboard -380 volts -50 Hz -Year of construction 2001
We sell 450 x NVIDIA RTX 6000 ADA, brand-new RTX 6000 Ada | 48GB GDDR6 | PCIe 4.0 x16 | 4× DisplayPort Part No.: 900-5G133-2250-000 (Bulk Pack) EAN: 8592978549763 Brand-new with manufacturer warranty! In most cases, the entire lot can only be handed over in its entirety. More information on request. In most cases, advertised products can only be sold as a complete lot. More information on request. We look forward to receiving inquiries from Germany and internationally. We have many more refurbished/used hardware from the areas of the systems mentioned here as well as from the areas of other systems from these manufacturers available: IBM, DELL, HPE, ORACLE, NETAPP, QUANTUM, STK, FUJITSU, SGI, HDS, EMC, Supermicro, BULL, NEC, CRAY, 3Com, ADVA, Alcatel, Brocade, Cisco, Enterasys, Extreme Networks, Huawei, Marconi, Nortel, Qlogic, Avaya, ORACLE Tested, tested used h ...
We sell 3000 x HP 64GB 2400MHz/2666MHz DDR4 ECC Server RAM Memory is out of HP servers BL460c Gen9 and Gen10. Around 50 % are 2400MHz, 50 % are 2666MHz. All memory is dual labeled, Samsung or Hynix and original HP! Also we will have these processors out of the same systems: 132 x Intel Xeon E5-2697Av4 96 x Intel Xeon E5-2690v4 76 x Intel Xeon Gold 6136 172 x Intel Xeon Gold 6248 Total count of processors: 476 In most cases, the entire lot can only be handed over in its entirety. More information on request. In most cases, advertised products can only be sold as a complete lot. More information on request. We look forward to receiving inquiries from Germany and internationally. We have many more refurbished/used hardware from the areas of the systems mentioned here as well as from the areas of other systems from these manufacturers available: IBM, DELL, H ...
1 x used double-sided Rotoles S600 with 2 grinding units and 1x brush Working width 600mmm Speed 60m/min Calibration milling planing machines with feed rollers Best accuracy of the boards and excellent results in delamination attempts, at any speed. ROTOLES S calibration machines are the best choice for calibrating boards and slats before gluing. Rotoles S calibration milling planing machines with feed rollers Best accuracy of the boards and excellent results in delamination attempts, at any speed. ROTOLES S calibration machines are the best choice for calibrating boards and slats before gluing.
completely stainless steel suitable thermo-oil heated (300 kW) 12 kW Frying length 7,500 mm Track width 600 mm Top band infinitely variable speed Oil pump Oil level control Suitable for fire protection Filter Dirt transport Lid mechanical lifting device insulated lid Dimensions (L x W x H) : ± 10,900 x 2,000 x 3,500 mm Siemens PLC control type S5 95U+ HMI Simatic OP27 suitable for CIP cleaning + Oil Management System Type VTC 2000 single-walled tank Oil pump Dimensions (L x W x H) : ± 1,700 x 1,1600 x 3,400 mm Oil level indicator
The scope of delivery includes: 01x Attachment frame frames, used Total weight: 27.23 kg Material color: blue Total width: approx. 600 mm Total depth: approx. 800 mm Total height: approx. 950 mm Usable height: approx. 800 mm Opening dimensions: approx. 550 x 520mm(WxH) Mesh size: approx. 50 x 50 mm Wire thickness: approx. 3.00 mm Tube profile: approx. 22 mm Consisting of 2 foldable side panels! 01x Disposable pallets, used Total width: approx. 600 mm Total depth: approx. 800 mm Height: approx. 150 mm Currently in stock Available: approx. 58 pcs. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on ...
Plasma cutting "CR" 6000x2500 with two Hyperterm HT 2000 and HD 3070 generators complete with filter
AGILENT HP 6890N System Agilent 6890N Gas Chromatogtaph Single FID detector Single Split/Splitless Inlet Agilent / HP 7683 Injector Agilent/HP 7683 Tray PC with preinstalled Chemstation software Refurbished
General Manufacturer: Spinner Type: TTC300 65SMMCY Control: Siemens 840D SL ShopTurn Year of Make: 2015 Travel X1 / X2 / Z / Y: 180 / 110 / 450 / +40-40 mm Rapid traverse X1 / X2 / Z / Y: 15 / 15 / 15 / 24 m/min Turning Spindle 1 Speed: 4,000 rpm Chuck size: 250 mm Spindle passage: 52 mm Spindle power S1 / S6: 21 / 27 kW Torque S1 / S6: 201 / 258 Nm Turning spindle 2 Speed: 7,000 rpm Chuck size: 130 mm Spindle power S1 / S3: 6 / 8.5 kW Torque S1 / S3: 49 / 68 Nm Revolver Number of tools: 12 + 12 (BMT45) Rotating Tools: 12+12 (BMT45) Speed: 6,000 rpm Power S1 / S3: 2.3 / 3.5 kW Torque S1 / S3: 7 / 11 Nm Dimensions and weight Dimensions: 2,700 mm x 1,900 mm x 2,165 mm Weight: 5,100 kg Condition Condition: Used Functional: Tested and fully functional Other equipment and accessories included: IKZ 50 bar with belt filter system Parts Conveyor Belt w ...
Box washer, Fabr. Drill, type: R 20, in VA, with hinge belt transport chain, pump, 2 VA screens, control cabinet, YOC 1989 Box washer, Fabr. Klann, type: 600, with large pump, with screening box with 3 VA screens, YOC 1988, dismantled Box washer, Fabr. Kettner/Sotec, Type: WAH 18, 1,800 Ka/h, with control cabinet, YOC 1990 Prices on request
; Gross weight [kg]: 17500; Engine: Cummins KTA50-GS8; Accessories: Tanker, Battery, Control Panel, Stahldach, Including: Coolant heater and battery charger; Water Tank Volume [l]: 1000
Cylinder cover Recon The cylinder covers were equipped with the following new parts: - Inlet and exhaust valve guides. - Intake and exhaust valve seats. - Inlet and outlet valves. - Nozzle protection tube. - Rotary device. The cylinder covers were tested with 10 bar water pressure. The cylinder covers were planned. The valves ground in with the seats and mounted with new valve stem seals. Price per piece.
Key data: 48 KW, 60 kVA, 400 V
On hand Perkins Engine Stamford Alternator ComAp Control ABB Disconnect Switches Generator Set Specifications: Model No.: EQ-P6048 Continuous power (Prime Rating): 60 kVA / 48 kW Emergency power (standby rating): 66 kVA / 53 kW Voltage: 400/230V Frequency: 50 Hz Speed: 1500 rpm Engine Specifications: Engine Brand: Perkins Engine Model: 1103A-33TG2 Bore x Stroke (mm): 105 x 127 Displacement (L): 3.3 Compression ratio: 17.3:1 Intake system: turbocharging & intercooler Fuel System: In-line Injection Regulator Type: Mechanical Dimensions of the generator set: Length: 2220 mm Width: 960 mm Height: 1258 mm Weight (open): 1085 kg Standard: 4-stroke, 1500 rpm, water-cooled robust diesel engine Leroy Somer Generator ABB Circuit Breakers Protection system in manual operation Flexible oil hoses and oil drain valve Preheater Lubricating oil and antifr ...
The scope of delivery includes: 01x Collision protection guardrail, used Total width: approx. 2,610 mm (outer – outer base plate) Inner width: approx. 2,515 mm f. Double rack rows up to 2,500 mm Total height: approx. 400 mm Total depth: approx. 220 mm Weight | Crash barrier: approx. 39.00 kg Consisting of each: 02x L-impact protection corners, used Material colour: yellow/black Total height: approx. 400 mm Total depth: approx. 305 mm Total width: approx. 265 mm Material thickness: approx. 4.00 mm 02x C-profiles, used Material colour: yellow Overall length: 2,360 mm C-profile: 180 x 40 x 15 mm Material thickness: approx. 2.50 mm 08x Hexagon Bolt, M12x35 08x Hexagon Nut, M12 16x washer, M12 Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for ...
KKK Turbocharger Overhauled K44 UB19 W8286 Q6 Ausf Nr 5344 990 6001
Good Plansifter BÜHLER MPAH 628 Screening box 2.15 h., 24 sieve, 6 pass. ( 2x B1, 2x B2, 2x B3 ) without sieve stacks, 36x floor nozzle ø150 new, Cleaned, drive reviewed
Many thanks for your interest on our second hand machines, please find follow our offer: Kadema enrober antique manufacturer: Kadema; Johannes Kegel Dresden Type: Juwel 620 enrober electrical: 400 VAC / 3 Ph Year of manufacturing: maybe between 1930 - 1940 work width: 620 mm different: with wooden cooling tunnel, approx. 8m fixed mass container We offer this machine in 'as is' condition, without warranty EXW Hess. Lichtenau, unpacked
Vibronics Ultrasonic Bath Brand: Vibronics Power 1.8 kw; Serial number: 6092 Total dimensions L: 2800 mm; W: 1700 mm; H: 930 mm; Tank size: WxHxD= 1350x720x990 mm Frequency 25 kHz equipped with 4x generators
USED KRAUSS MAFFEI HZ 630 PH CENTRIFUGE REF.: C6486 General characteristics: Manufactured by KRAUSS MAFFEI Model HZ 630 Ph Technical characteristics: Basket diameter 630 mm Max. rotational speed 2400 rpm
; Gross weight [kg]: 13000; Engine: DC16 320A 02/63; Accessories: Tanker, Battery, Control Panel, Stahldach, - Super Silent Canopy; Water Tank Volume [l]: 2500
We offer for sale two pieces MWM TBG 616 V8 K.. Technical data engine: Engine manufacturer: MWM Engine type: TBG 616 V8 K Rated power: 300 kW Speed: 1500 rpm Fuel: Natural gas Technical data generator: Generator manufacturer: Stamford Generator power: 600 KVA Voltage: 400 / 231 Volt Power factor: cos. - phi 0.8 Speed: 1500 rpm Year of construction: 2004 Operating hours: 57,000 h Location: Cologne
Technical data for the shelving system: Shelving system: META Type: CLIP Technical data for the installation: Number of rows of shelves: 01 pcs. Shelf length: 1,100 mm Number of fields per row of shelves: 01 pcs. Number of grating shelves: 06 pcs per field The scope of delivery includes: 02x Shelf stand, used Material color: blue Frame profile dimensions: 50 x 40 x 1 mm Adjustment grid: 25|25 mm incl. base plates and gravel bar The stands are pre-assembled 2,490 mm high 635 mm deep 06x Shelves, used Soil name: V100 Material colour: creamy white Dimensions: 1,000 x 600 x 40 mm Weight: 4.04 kg|pcs. max. load per shelf 100 kg with evenly distributed load 04x Levelling plates, used Dimensions: 76 x 58 x 2 mm Weight|Pcs: 0,064 kg Material colour: sendzimir galvanised 24x Shelf Racks, used Weight|pcs.: appr ...
maximum number of results exceeded
please refine your search
