133,845 used machines on RESALE, but how to find them? Machine Search
Process chiller / chiller air-cooled, Type: TAEevo Tech 351 P5-offAD bypass MTA S.p.A. TAEevo Tech 351 P5-offAD Bypass are air-cooled compact water chillers suitable for outdoor installation down to -5°C. Including crank pan heater, electronic expansion valves, phase monitoring, buffer tank 350 liters and built-in P5 high-pressure pump. Extras: - Open filling system/ tank attached - Bypass with manual valve between water inlet and outlet Cooling capacity kW 66 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h) 11.2 Available pump pressure (bar) 4.68 Ambient temperature (°C) 32, Refrigerant R 410A, Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW) 39 Max. Current (A) 68 Starting Current Circuit (A) 213 Protection class: IP54 Dimensions: Length (mm) 2250, Width (mm) 866, Height (mm) 2054, Weight (kg) 108 ...
Model SC-120 Corn cutter provides maximum product recovery, high throughput, low maintenance and automatic corn removal from the cob at high speed. Each ear is placed on the feed through chain, tip end first. The stainless chain moves the ear of corn into the feed rolls. Two sets of feed rolls line the ear of corn up with the cutter head and move the earinto the cutter knives. The cutter knives are automatically openend for cutting by the feed roll gauging sytem. Kernels fall through the head and is discharged to a takeaway conveyor. A water spray is directed into the cuto-off corn area to minimize the starch build up.
Key data: 1150 , 650 , 500
Machine details Bearing number 1105-02989 Machine type Machining Center - Vertical Make MAZAK Type VTC 20 B Built in 1996 Control type CNC Warehouse FRANCE Country of origin Japan Delivery time immediately Freight base from stock Technical details Information CNC control MAZATROL M PLUS , 24 X-fold tool changer, coolant device 10000 R/MIN
The system has been modernized several times by Cemecon, most recently in 2023 to the latest software version Last service 2023 of Cemecon Pure research plant: number of batches approx. 1600 processes The facility is equipped as follows: Six cathodes All DC cathodes, two of them also HIPIMS BIAS: DC, MF, HIPIMS Booster Anodes 3 x heaters Interface for precise tapping of the Peak –I, -U + -P in HIPIMS mode via BNC (with oscilloscope) 2 turbopumps 4 gases, 1 of which is flammable Table of 6 The following accessories can be taken over with the system: water/water heat exchanger, second 6-seater table with base and "pallet truck", 2-person gas cylinder cabinet, spare sheet set, spare heaters, charging material, many targets (all German manufacturers, no China imports) and a variety of accessories and spare parts.
Qty. 1 Second-hand aluminium strip production plant Entry Material: Aluminium Scrap – HD666, AA5050, 2.5-3.0% Mg Final product: Aluminium strip (can stock) Width: 220 mm Thickness: 0.15 – 1.0 mm Mfc.: De Winter, Thermcon, Fata Hunter, Fröhling, Nederman, Burghardt & Schmidt, Siemens Built: 1984, 1999, 2000, 2002, 2014, 2015 Scope of supply: Melting Furnace Tilting Casting Furnace Block Caster 5 Stand Hot Rolling Mill 6 Stand Cold Rolling Mill Hot Gas Filter Slitter Welding Machine Treatment Furnace Quenching Unit Shear
Complete precision ball screw drive with bearings, stroke 308mm, 25x5/25, Rexroth, new Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition in original packaging! The part was purchased from a spare parts warehouse of a company and has never been in operation, is in a completely mint condition and in its original packaging. Complete precision ball screw with pillow block and floating bearing, thread diameter 25mm x 5mm ball screw Plummer block Rexroth: R159161720 Plummer block Rexroth: R159111720 Ball screw nut with part holder: R150321085 Total 496 x 110 x 72mm Maximum stroke: 308mm Function guarantee! For second hand parts, we can not accept any conventional guarantee and warranty. But we give you a functional guarantee. If the device does not work within 3 months after purchase you can return the goods and we wi ...
Compresor system Prematic 388/150 PAKO vollaut. L x W x H: 1.1 x 0.7 x 1.2 m Weight approx. 120 kg Built in 2016 Refrigeration dryer Prematic IDFA The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Process chiller / chiller air-cooled, Type: Galaxy GLT 135 SHE MTA S.p.A., The Galaxy GLT 135 SHE are compact chillers designed for outdoor installation (from -20°C to +43°C) are suitable with plate evaporator, scroll compressors, control and control cabinet, shut-off valves for compressors, equipment for low ambient temperatures down to -20°C (EC fans), P2 pump, 510 litre buffer tank, electr. Antifreeze heating, condenser filter mats incl. Vitaulic couplings. Cooling capacity (kW): 354 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h): 60.7 Available pump pressure bar: 2.51 Ambient Temperature (°C): 32 Refrigeration circuit: Refrigerant R 410A Refrigeration Circuits (Quantity): 2 Compressors (quantity): 6 Power levels (%): 0-17-33-50-67-83-100 Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW): 167.7 Ma ...
Masterwood Italy CNC Ventilation Center for Door and Window Production Type Woodmaster ATLAS Built in 2000 SN 00120018 for the processing of solid wood and panel material, etc. Working strokes of the axles: X Axis 3900mm Y Axis 1785mm Z- Axis 630mm Workspace X Axis 3500mm Y Axis 1210mm Z- Axis 210mm Max speed of axles 60-50-20m/min 6 edition consoles Workpiece clamping device Electric main spindle with ISO 30 intake 6.8 kW 24,000rpm Saw unit integrated in the work unit Automatic change of tools 18 positions Numerical control SINCRO with industrial PC and keyboard Safety tread mats Vaccum Pump Total required power 27 Kw Care pressure 6-7 atm Compressed air consumption per arebit cycle 200-300Nl/min Suction speed 25-30m/sec Air consumption 5000m3/h 400 V/ 50 Hz Weight 4500 Kg Technical information subject to reservation
Biesse Italy, Rover 22 CNC Machining Center Built in 2001 SN 07498 Workspace 4 axes X-axis 3060 mm Y-axis 1080 mm Z-axis 155 mm 6 consoles with 18 vaccum suction holder 4 pneumatic bakelite rods for lifting the plate Vertical electric spindle 7.5 kW with automatic tool change, ISO 30 cone Automatic tool change 7 positions on the working head Drill head with 20 spindles arranged as follows: 7 vertical in X-axis 7 permeable to Y-axis 4 horizontal in X-axis 2 horizontal in Y-axis Groove saw 120mm Safety tread mats 110 m3 / h vacuum pump CE marked Weight 3500 Kg Technical information subject to reservation
Process chiller / chiller air-cooled, Type: Galaxy GLT 135 SHE MTA S.p.A., The Galaxy GLT 135 SHE are compact chillers designed for outdoor installation (from -20°C to +43°C) are suitable with plate evaporator, scroll compressors, control and control cabinet, shut-off valves for compressors, equipment for low ambient temperatures down to -20°C (EC fans), P2 pump, 510 litre buffer tank, electr. Antifreeze heating, condenser filter mats incl. Vitaulic couplings. Cooling capacity (kW): 354 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h): 60.7 Available pump pressure bar: 2.51 Ambient Temperature (°C): 32 Refrigeration circuit: Refrigerant R 410A Refrigeration Circuits (Quantity): 2 Compressors (quantity): 6 Power levels (%): 0-17-33-50-67-83-100 Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW): 167.7 Ma ...
Twin pallet vertical machining center CHIRON FZ15KW Highspeed Spindle 12000 RPM Rapids asse Z 60m/min 2005 Pallet 2 x 660 x 400 mm X 550 Y 400 Z 360 coolant through spindle 48 tools HSK63 swarf conveyor CNC Siemens 840D This Machine can be inspected and tested under power in our warehouse in Gussago BS Italy
Conveyor belt incl control (speed control) Tread Length 105cm Width 20cm Height
AIR LIQUIDE CB MATIC SM 42X43 column and boom was manufactured in 2016 in France by Air Liquide Welding (now Lincoln Electric). The machine, designed for precision circumferential and longitudinal welding, is the perfect solution for companies specialising in the manufacture of, among others, steel structures, pipelines, tanks and wind turbine towers. The welding process is performed fully automatically by means of a welding heads system, which enables the welding of two welds simultaneously on tubes with a maximum diameter of 4000 mm and I-beams with maximum dimensions of 3000 x 800 mm. The use of this solution significantly reduces production time, while maintaining high precision and efficiency at the same time. The CB MATIC SM 42X43 welding boom on offer has a tube welding head for submerged arc welding (SAW) with a range of safety systems, i.e. laser pointers, sensors and a visio ...
ATMOS PDS PDP 35 towable air compressor was built by ATMOS Chrást s.r.o. in the Czech Republic in 2021. The machine is used wherever top-quality compressed air is required. Its components from renowned European brands ensure the highest possible energy efficiency throughout its entire service life. The compact design based on a single-axle trailer, in turn, allows operation in all conditions, both at low and high temperatures. The ATMOS PDP 35 diesel air compressor weighs 768 kg. The machine has only been used for 350 hours and is in very good condition. At 250 operating hours a service was performed. Technical specifications of the ATMOS PDS PDP 35 rotary screw compressor - motor power: 35.7 kW - working pressure: 7 bar - maximum capacity: 5 m3/min - power source: combustion engine - operating hours: 350 h - weight of the ATMOS machine: 768 kg
Fully refurbished Probat UG22 with chaff cyclone. Main features: Capacity: up to 22kg of green coffee per roast (88kg per hour) Roasting time: 12-15 minutes Voltage: 400V, 3 phase, 60Hz (other voltages by request) Gas: natural gas/LPG - modulated burner - separate Siemens motors for every function (drum, exhaust fan, cooling tray arms, cooling fan), enables to roast and cool simultaneously - speed controlled motors on the exhaust fan and drum for maximum control over the roasting process - two digital thermocouples (bean temperature and exhaust temperature) - analog thermometer in the exhaust - new control cabinet with buttons for all the functions doubled by an 10inch touch screen display - Artisan and Cropster connection through RJ45 ethernet cable/socket - new stainless steel cover - new stainless steel cooling tray sheathing - new insulation of the drum - new ...
core engine Centaur 50. The turbine and associated gearbox have been completely base overhauled after last operating and are a ready-to-install for a zero-hour turbine exchange. After the overhaul, there was no active operation / no installation. The turbine and gear box Sale Solar Centaur 50 Base overhauled core engine: Manufacturer Solar Turbines - Type CENTAUR 50 SoLoNox - Year of construction 2022 Zero-hour core turbine and gearbox - Electrical output 4,040 kWel - Speed 14,944 rpm 50Hz - Fuel Natural gas H - Design temperature 15° C - Turbine inlet temperature 665 °C (1.229 °F) - Gearbox with zero operating hours - Turbine control Solar TTS4
The iCombiPro is the latest combi steamer from RATIONAL. The iCombiPro 20.1/1 gas model with 20 plug-ins GN 1/1 is easy to use, even for unskilled personnel, as you can achieve outstanding food quality without any monitoring effort. The super-fast intermediate & self-cleaning keeps your device sparkling clean. The device has been tested in our in-house specialist workshop and is fully functional. Rjbpextm D Heuvnljch These are sample photos, originals will follow shortly. The combi steamer is available from kW 44. You will receive an invoice with VAT. Service: We will be happy to put you in touch with a certified Rational customer service throughout Germany. Are you looking for a specific Rational appliance type? Ask us, we have access to an extensive range of used and new goods. We will be happy to advise you on all types of devices, whether SCC, CM, CMP, VCC, iVario, iCo ...
Control: Siemens 840D Country of origin: Germany Spindle speed n-1: 12,000 Spindle motor kW: 9 Z - Path mm: 510 Y - Path mm: 510 X - Path mm: 835 Speed m/min: 30 Tool holder: HSK 40 Table load: 800 kg Clamping area mm: 1,000 x 560 Machine footprint mm: 2,100 x 2,700 Machine weight approx. kg: 4,200
Open spray level 2x2.1x2.2 The overspray in powdering is absorbed via the suction unit. The powder spray stand is delivered on rollers and is thus mobile. - The suction is equipped with a 60 L powder container (rollbar). - The first stage is 4 filters in the suction system. - Above the cabin is the Absolute filter. 1. Dimensions of the powder level width 2,000 mm Depth 2,100 mm Height 2,200 mm 2. Fan 1 pc. 6,000 m3/h Electric motor 3.0 kW 3. Filter 325x600 4 pcs. Type Filter cartridges 4. Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5. Absolute filter 1 pc. type pocket filter
Powder incineration furnace 2,000 x 1,900 x 2,000 mm 1 inner dimension length 2,000 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m3/hr 10 Electric motors 1 pc. 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 33 kW = 28,380 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 Burner 1 pc. furnace is operated with gas burner 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide
Powder incineration furnace 2,000 x 1,900 x 2,000 mm 1 inner dimension length 2,000 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m3/hr 10 Electric motors 1 pc. 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 33 kW = 28,380 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 Burner 1 pc. furnace is operated with gas burner 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide
Powder incineration oven 3,500 x 1,900 x 2,000 mm electric 1 inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m3/hr 10 Electric motors 1 pcs. 3 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 58 kW 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electrically heat-resistant fans and heat-resistant bearings, thermoblock has overheat protection 14 Burner 1 pc. oven is electrically heated 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide
Powder incineration furnace 3,500 x 1,900 x 2,000 mm gas operation 1 inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m3/hr 10 Electric motors 1 pcs. 3 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 58 kW = 49,880 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 burner 1 pc. oven is heated with gas burner. 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide
Powder incineration oven 4,500 x 1,900 x 2,000 mm electric 1 inner dimension length 4,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 5,700 = 11,400 m3/hr 10 Electric motors 2 pcs. 2x 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 74 kW 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electrically heat-resistant fans and heat-resistant bearings, thermoblock has overheat protection 14 Burner 1 pc. oven is electrically heated 15 Exhaust air 1 pc. device for exhaust air pipe, manual f ...
Machine details Bearing number 1105-03199 Machine type Milling machine - Universal Make DECKEL MAHO DMG Type DMU 70eVolution Built in 2001 Control type CNC Warehouse FRANCE Country of origin Germany Delivery time by arrangement Freight base from location Price Technical details x-path 750 mm y-path 600 mm z-way 520 mm Control HEIDENHAIN iTNC 530 Information Milling machine - Universal DECKEL MAHO DMG DMU 70eVolution NC Swivel Round Table (700X500) Spindle -------------------- Spindle speed: 18,000rpm Tool holder: SK40 Tool changer -------------------- Magazine places: 32 Pick up Facilities -------------------- Measuring probe Conveyor 2. Processor card electronic handwheel HR410 Blowing air M25 Rinsing gun
Replacement columns for die-casting machine OL1500, D250x12, Oleopress, used - overhauled Special price! Attention: The current new price is certainly twice as high. In addition, we also have a new spar nut and 2 adjusting nuts in separate adverts. If you have a VAT number, we will be happy to issue you with an invoice without VAT. Second hand! The part was bought from a spare parts store of a company, it was overhouled by a specialist company, is in a very good condition and fully functional. Attention: We have not cleaned the column yet, as the fat layer is optimal for storage. Material 25CrMo4 Manufacturer Olepress / O.P. DIE Casting Thread 250 x 12mm Thread fixed end 300mm lg Thread adjustable end 1160mm lg Weight approx. 2300 kg Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250 ...
Replacement columns for die-casting machine OL1600, D250x14, Idra, new -50% Special price! Attention: The current new price is certainly twice as high. If you have a VAT number, we will be happy to issue you an invoice without VAT. As good as new in original packaging! The part was bought from a spare parts store of a company and has never been in use, is completely as new and in the original packaging. Material 25CrMo4 Manufacturer Olepress / O.P. DIE Casting Thread 250 x 14 mm, L 5908 mm, Thread fixed end 290mm lg Thread adjustable end ca. 1160mm lg Weight approx. 2300 kg Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D300
Replacement columns for aluminium die-casting machine OL2000, D285x10, Oleopress, new -50% Special price! Attention: The current new price is certainly twice as high. In addition, we also have a spar nut and 2 adjusting nuts in separate adverts. If you have a VAT number, we will be happy to issue you with an invoice without VAT. As good as new in original packaging! The part was bought from a spare parts store of a company and has never been in use, is completely new and in ist original packaging. Material 25CrMo4 Manufacturer Olepress / O.P. DIE Casting Thread 285 x 10mm, L 6830mm Weight approx. 3400 kg Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D300
Printing Width: 1250 mm // Web Width: 1300 mm
X Travel 1100 mm Y Travel 610 mm Z Travel 610 mm Spindle speed 10.000 Rpm Controller Siemens 840 Dsl
Replacement welding controllers 19" for resistance welding machines MPS 100mono MPS 100monoR1 MPS 100multi MPS 100multiR1
Replacement welding controllers 19" for resistance welding machines MPS 8043/1 MPS 8043 Q
Core diam.: 230 mm // Material Type: Cardboard, pvc, pp , pe and hdpe cores
Bartscher refrigerated table 0 °C to 10 °C 1 unit – double benefit: convection cooling ensures a constant and uniform cooling temperature inside the refrigerated table with 1 door and 4 drawers. With its high-quality and robust stainless steel surface, the appliance can be perfectly integrated into any kitchen and can also be used as a work surface. • Number of drawers: 4 • Door hinge: Left • Door Type: Hinged Door(s) • Number of doors: 1 • Number of cabinets: 1 • Cabinets refrigerated: Yes • Drawers refrigerated: Yes • Standard format drawers: 1/1 GN • Connected load: 0.452 kW | 230 V | 50 Hz • Feet height adjustable: Yes • Temperature range: 0 °C to 10 °C • Height adjustable: 850 mm to 900 mm • Backsplash: 50 mm • Cooling: Convection • Refrigerant: R134a • Digital Display: Yes • Depth GN container max.: 150 mm • On/Off S ...
Manufacturer: SOMMERMEYER Filtertechnik GmbH Type: SF 38 Y.O.M.: 1997 Conveyor length total approx. 3000 mm Throw in: approx. 1300 x 400 x 400 mm Ejection height approx. 1300 mm Drive Gearmotor 0.25 kW 220/400 V Coolant pump Brinkmann TB303/300 160 l/min H: 18 m 1.7 kW 230/400 V Total dimensions: approx. 3000 x 1600 x 1700 mm All items are checked for function before delivery, if technically possible! Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.
FN Steel high‑capacity hybrid rolling mill - continuously modernized through major upgrades - delivers wire rod and bar‑in‑coil from Ø 5.5 mm to Ø 30.0 mm at speeds up to 100 mps. Combining technology from the three major OEMs, it offers speed, flexibility, and quality for the most demanding markets. ‘SMS-PRIMETALS-DANIELI’ High Speed Wire-Rod & Bar-in-Coil Rolling Mill Highlights Wire-rod (‘Morgan line’): Ø 5.5 –16.0 mm with pre-finishing and reducing sizing mills Bar in Coil (‘Garret line’): Ø 16.5 –30.0 mm with two coilers for higher output On-line Heat Treatment: water boxes and temperature-controlled cooling conveyor to achieve desired microstructures Capacity: > 400,000 tons per year Applications: High‑carbon, alloy, bearing, spring, cold‑heading steels Rolls & Guides’ Shop: Fully equipped workshops Spare Parts: L ...
TECHNICAL DATA: 04 roller conveyors mm: 1900 x 6000 01 roller conveyor mm: 3000 x 1200
Technical data: - Load capacity E. chain hoist 250 kg - Lifting speed approx. m/min - Operation of the chain hoist via hand remote scanner - Man. Process hoist / transverse path + longitudinal path - Track gauge variable to approx. 3500 mm - Hook height approx. 2800 mm - Crane track length approx. 5000 mm - Height approx. 3900 mm - UK crane carrier approx. 3000 mm - 4 pieces of steel supports made of recheck tube 150 x 100 mm H 3900 mm - 2 longitudinal suspension carriers approx. 5000 mm - Cross suspension carriers approx. 3500 mm - Weight of the plant approx. 1000 kg
Technical data: - Load capacity E. chain hoist 250 kg - Lifting speed approx. m/min - Operation of the chain hoist via hand remote scanner - Man. Process hoist / transverse path + longitudinal path - Track gauge variable to approx. 3000 mm - Hook height approx. 2200 mm - Crane track length approx. 4000 mm - Height approx. 3500 mm - UK crane carrier approx. 2700 mm - UK - longitudinal rail approx. 3000 mm - 4 pieces of steel supports made of recheck tube 150 x 100 mm H 3500 mm - 2 longitudinal suspension carriers approx. 4250 mm - Cross suspension carriers approx. 3000 mm - Weight of the plant approx. 1000 kg
1 gebr. Corundum disc mill type T4, in vertical version Technical data: Make: KORUMA Type: T4 Drive power: 18.5 KW three-phase motor (completely new drive motor) Operating voltage: 400 V, 50 Hz, 3 phases Protection: IP 54 Speed: 3000 rpm Material of the product-contacting parts: 316 L (1.4404/1.4435) Shaft sealing: shaft sealing ring Side seals: EPDM Connections: Suction side DN 80 DIN 11851 Capacity: 300-1800kg/h Grinding discs: 240mm Gehäuse_ with double sheath for heating/cooling
Process cooler, chiller, chiller - air-cooled, Manufacturer: MTA S.p.A. Type: TAEevo Tech 902 P3 TAEevo Tech 902 P3 are air-cooled compact water chillers suitable for outdoor installation (from -5°C to +46°C). Including crank tray heating, phase monitoring, buffer tank 950 ltr. and built-in P3 circulation pump. Cold water outlet temperatures from -10°C to +30°C are adjustable. Cooling capacity kW 178 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h) 30.4 Available pump pressure (bar) 3.16 Ambient Temperature (°C) 32 Refrigerant R 410A, Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW) 90 Max. current (A) 160 Starting Current Circuit (A) 365 Protection class: IP54 Dimensions: Length (mm) 4655, Width (mm) 1250, Height (mm) 2151, Weight (kg) 2907 Connection Rp 3" Serial No.: 2200360489 Year of const ...
Process cooler, chiller, chiller - air-cooled, Manufacturer: MTA S.p.A. Type: TAEevo Tech 902 P3 – 178 kW TAEevo Tech 902 P3 are air-cooled compact water chillers suitable for outdoor installation (from -5°C to +46°C). Including crank tray heating, phase monitoring, buffer tank 950 ltr. and built-in P3 circulation pump. Cold water outlet temperatures from -10°C to +30°C are adjustable. Cooling capacity kW 178 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h) 30.4 Available pump pressure (bar) 3.16 Ambient Temperature (°C) 32 Refrigerant R 410A, Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW) 90 Max. current (A) 160 Starting Current Circuit (A) 365 Protection class: IP54 Dimensions: Length (mm) 4655, Width (mm) 1250, Height (mm) 2151, Weight (kg) 2907 Connection Rp 3" Serial No.: 2200360489 Ye ...
Machine details Bearing number 1105-02750 Machine type Machining center - Universal Made DMG DECKEL-MAHO Type DMU 50 eV / 5 axes Built in 1998 Control type CNC Warehouse FRANCE Country of origin Germany Delivery time immediately Freight base EX WORK Technical details x-path 500 mm y-path 420 mm z-way 380 mm Control HEIDENHAIN TNC 430 Spindle cone HSK 63 Speeds 18,000 rpm Spindle motor 15 kW Rapid response 50 m/min Table clamping area 500 throughs. x 380 mm Feed range up to 20 000 mm/min Tool change device 32 fold Total power requirement 38 kVA Machine weight approx. 5.9 t Information - CNC - Screen web control HEIDENHAIN TNC 430 5-axis machine with B +C axis SIMULTAN - Machine documents spaenefoerderer
Drive control system Weiss, EF1503A, EPZ10201 APPL + Inv 8200, Lenze, new Special price If you have a VAT number, we will gladly issue you an invoice without VAT. New! The part was purchased from a company's spare parts warehouse, is in its original packaging, has never been used and is completely new. Also suitable for controlling a Weiss rotary indexing table Includes documentation 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for direct and indirect consequential damages. Our terms and conditions apply, see our website. Austrian law applies without exception and court location St. Pölten.
maximum number of results exceeded
please refine your search
