heated used for sale

Qty. 1 Second-hand gas heated log furnace including hot shear Mfc.: ELHAUS Type: L250-90/135/4FK – WS250BD Built: 1999 Log dia.: 10” – 254 mm Log length: 5 – 7 m Billet length: 650 – 1300 mm Min. shear temperature: depending on the alloy approx. 340 – 400 °C Log temperature max.: 530 °C Heated by natural gas Hu=8.600 kcal/Nm³ Gas consumption: 234 kWh/tAl – 23.5 Nm³/t Al El. power: 130 kW Number of heating zones: 4 Number of circulating zones: 3 Dimensions of the furnace: 14.75 x 2.2 x 3.9 m - L x W x H Hot shear Recoil pressure: 0 – 100 bar Recoil stroke: 1.85 m Shear force: max. 1.69 MN at 210 bar Shear stroke: 360 mm Output pressure: max. 160 bar Output stroke: 325 mm Closing pressure: 210 bar Spreading stroke: 2 x 4.0 mm Dim.: Height above hallway: 2.9 m Length over everything: 3.95 m Width over everything: 2.65 m Hydraulic station Max. ...

Electrically heated continuous furnace, make VEI-Engineering type: DLNTO-EB 830-500 heat treatment: tempering temperature max. 500°C working temperature: 220-450°C clear dimensions (w x h): 800 x 210 mm heated length: 4.950 mm heating power: 2 x 30 kW fans: 2 x 5,5 kW Cooling water for 2 heat exchangers: inlet max. 2 bar PLC: Siemens S7

Choice of 3 x RENTEC n.v. (Belgium) steam heated autoclaves Internal dimensions: 3000mm dia x approx 2500mm long (inc. dished end and door), Working pressure 10 Bar, Hydraulic Bayonet type door Year of manufacture 1995 Drawings and documentation available. No controls or hydraulic unit for door (all 3 were running off 1 pump). In very good condition.

Electrically heated chamber furnace, make VEI type: KA_EB_TO external dimensions (w x h X d): 2500 x 2900 x 1700 mm usable dimensions (w x h X d): 1250 x 2000 x 1250 mm temperature: 250 ° C heating power: 24 kW

Gas heated tempering furnace, make VEI type: KA_TRU_GB external dimensions (w x h x d): 1700 x 2050 x 3900 mm useable dimensions (w x h x d): 600 x 850 x 1800 mm temperature: max. 600°C circulation fan: 4,0 kW loading weight: 3.000 kg gross

electrical heated tempering continuous furnace external dimensions: lenght: 3900 mm width: 1320 mm height: 1090 mm (above base frame) muffle lenght: 3960 mm max. furnace area temperature: 750°C max. temperature inside the muffle: 700°C water cooled ventilators : 3 electrical connected loads: three-phase: 3 x 400 V, 50 Hz power consumption: 75 kVA heating power, 3 zones each: 24 kW = 72 kW PLC : Siemens S7

Electrically heated circulating air furnace (horizontal air flow) max. temperature: 550?C useable dimensions (w x h x d): 900 x 1300 x 1800 mm charge weight: 800 kg gross heating power: 72 kW circulation fan: 1 x 7,5 kW

Beer grill AG heated showcase, type: WP 1/1, number: 40179 and WP2/1, number: 40163, plate dimensions: 670 mm x 520 mm, tray dimensions: 520 mm x 340 mm x 100 mm, total dimensions: 1080 mm x 840 mm x 700 mm.

API / Endress + Hauser / Hrale steam heated pasteurization unit, with API heat exchanger, fabrication number: PA-101439, year of construction: 2011, dimensions: 1300 mm x 900 mm x 2000 mm.

Grill, gas heated, dimensions: 400 mm x 900 mm x 950 mm.

DBK David + Baader GMBH Industrial Furnace Electrically heated convection oven Type ITHU 150° Type ITHU Identification number 871126 Year of construction 2006 Usable space/furnace 8,393 m3 Steam room/furnace 11.5 m3 Weight 3000kg Rated voltage 400/230V 50Hz Power supply 21KVA Heating capacity 18 KW Rated current 30 A Pre-fuse 50 A Protection class IP 43 Highest drying temperature 120° exhaust air volume flow/furnace 95 m3/h

DBK David + Baader GMBH Industrial Furnace Electrically heated Convection oven Type ITVU 200° TYPE ITVU Identification number 870233 Year of construction 2006 Usable space 2.8 m3 Steam room 3.9 m3 Weight 850 kg Temperature 200° Rated voltage 400/230V 50Hz Power supply 21 kVA Heating capacity 18 kW Rated current 31A Pre-fuse 50 A Protection class IP 43 Exhaust air volume flow 230 m3/h

Umur 5 layers oil heated hot press Machine is in very good condition Automatic 1150 mm X 2250 mm

not suitable for the evaporation of flammable solvents, interior 1500 mm width, 1400 mm depth, 1950 mm height, volume approx. 4.1 m³, double-walled welded sheet steel and profile frame construction, robust design, heating capacity 13.5 kW, temperature uniformity +/- 3 % of setpoint in the persistent state, nominal temperature 75°C, maximum temperature 100 °C

IBC stainless steel container transport container electrically heated 1,000 ltr. Content: 1.000 Ltr. Working pressure: max. vapour pressure 1.1 bar at 50°C, 1.3 bar at 55°C Material: Stainless steel, 1.4404 inner tank, 1.4301 frame and outer jacket Design: cubic, upright, on 4 feet, with welded-on construction for use by forklift or pallet truck, Insulating sheath with perlite insulation, electrically heated up to 120 °C, 2,000 W, 230 V, Inner tank lined with ETFE coating Outlet with butterfly valve DN 80 reduced to DN 50, lid DN 400, 1 x safety valve, 1 x Kamlock coupling 1", Total weight 381 kg final use: Food Height: approx. 1,670 mm Width/length: approx. 1,200 mm/1,100 mm

Press which can be used for manufacturing seals / (resin) composite parts / compression molding / circular sawblades / abrasive products / pressing from (metal)powder to parts / ... with heated table max 220 - 240° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Capacity: 100 ton Passage between uprights: 530 mm Max ram adjustment: 200 mm Distance between table -- ram: 250 mm Table area: 502 x 502 mm Ram area: 530 x 500 mm Length: 1600 mm Depth: 1200 mm Height: 2300 mm Weight: 2 ton Compression press / Grinding wheel press / Vulcanizing press / Elastomer press Kompressionspresse / Schleifscheiben Presse / Vulkanisierpresse / Elastomer Presse

Electrically heated conveyor furnace

Gas-heated conveyor belt furnace

Darragon Induction heated press

Press which can be used for manufacturing seals / (resin) composite parts / compression molding / circular sawblades / abrasive products / pressing from (metal)powder to parts / ... with heated table + 2 watercooled tables max 220 - 240° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Possible to program: - different temperatures - holding time of press under pressure - multiple cycles Capacity: 600 ton Passage between uprights: 1020 mm Stroke: 400 mm Distance between table -- ram: 400 mm Table: 1000 x 1000 mm Length: 1590 mm Depth: 1150 mm Height: 3700 mm Compression press / Grinding wheel press / Vulcanizing press / Elastomer press Kompressionspresse / Schleifscheiben Presse / Vulkanisierpresse / Elastomer Presse

Press which can be used for manufacturing seals / (resin) composite parts / compression molding / circular sawblades / abrasive products / pressing from (metal)powder to parts / ... with heated table + 2 watercooled tables max 220-240° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Multiple cycles can be programmed Press with 2 pistons: Capacity lower piston: 750 ton (with digital readout for applied force) Capacity upper piston (counter pressure): 250 ton (with digital readout for applied force) Passage between uprights: 850 mm Distance between table -- ram: 500 mm Table: dia 800 mm Weight of press: 14 ton Compression press / Grinding wheel press / Vulcanizing press / Elastomer press Kompressionspresse / Schleifscheiben Presse / Vulkanisierpresse / Elastomer Presse Height: 3700 mm Weight: 14 ton

with 3 heated tables + 2 watercooled tables max 220 - 240° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Capacity: 100 ton Passage between uprights: 600 mm Distance between table -- ram: 600 mm Table: 600 x 600 mm Length: 1500 mm Depth: 1150 mm Height: 2000 mm

Press which can be used for manufacturing seals / (resin) composite parts / compression molding / circular sawblades / abrasive products / pressing from (metal)powder to parts / ... with 3 heated tables + 2 watercooled tables max 220 - 240° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Capacity: 150 ton Passage between uprights: 670 mm Max stroke: 600 mm Distance between table -- ram: 600 mm Table: 670 x 670 mm Length: 1120 mm Depth: 1200 mm Height: 3600 mm Compression press / Grinding wheel press / Vulcanizing press / Elastomer press Kompressionspresse / Schleifscheiben Presse / Vulkanisierpresse / Elastomer Presse Height: 3600 mm

with 3 heated tables + 2 watercooled tables max 200° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Capacity: 100 ton Passage between uprights: 600 mm Max stroke: 500 mm Distance between table -- ram: 500 mm Table: 600 x 600 mm Length: 1450 mm Depth: 1250 mm Height: 2150 mm

with 3 heated tables max 200° Cnbsp; Press has been developed to be able to remain under pressure for 24 hours! Capacity: 100 ton Passage between uprights: 550 mm Distance between table -- ram: 400 mm Table area: 550 x 550 mm Length: 1500 mm Depth: 950 mm Height: 1910 mm

Hot press for manufacturing grinding wheels Height: 3400 mm

Stainless steel For continuous mixing of liquid and solid masses Quickly changeable agitators and mixers Double-walled, heatable housing Quick-dismountable cover

USED CENTRIFUGAL MOLECULAR DISTILLATION SYSTEM Manufacturer: MYERS VACUUM, Inc. Model: PILOT 15 LAB Throughput Capacity 10 - 80 lbs/hr (4.5 – 36.3 kg/hr) Type Continuous Pumping system ultimate pressure: 2 X 10-4 Torr Operating Pressure 10 -3 Torr to Atmosphere Mechanical Forepump >11 CFM High Vacuum Pump 320 L/sec of air at 250C. Power: 10-15 KW/ hour 3 phase wye” 115/208 V, 5 wire 50/60 HZ Available for 230, 415 or 460 Volt. Water: (20°C) 2 gal/min (7.6 L/min) Liquid nitrogen consumption: 0.5 liters/ hour (Utility consumptions may vary depending on process conditions) Dimensions: Height 69 Inches (1.75m), Width 34 Inches (.86m), Depth 59 Inches (1.5m) Net Weight 1300 lbs. (590kg) Centrifugal molecular distillation is a purification technique, which has gained wide acceptance in the chemical, food processing, pharmaceutical, and petroleum industries as well as t ...

Documents drawings_information_parr_5410.pdf equilabo_offer_details.pdf Technical details The distinguishing feature of a fluidised bed reactor is that the bed of solid particles or catalyst is supported by a rising gas stream. This reactor allows the catalyst to be easily loaded and removed. This is advantageous when the solids bed has to be removed and replaced frequently. High conversion at high throughput is possible with this style of reactor. These reactors inherently have excellent heat transfer and mixing characteristics. GAS FEED: Two reactant gas feed lines, each with normally-closed automated pneumatic shut-off valve, filter, bypass valve, and reverse-flow check valve. One gas feed line has a mass flow controller sized for up to 0.5-25 SLPM of nitrogen with up to 2 bar delivery pressure. The other gas feed line has a mass flow controller rated for up to 50  ...

Integrated equipment for production of chocolate, chocolate cream and chocolate coating for ice cream. The fat is melted in the heated fat melting tank, then fat is dosed into the temperature controlled chocolate ball mill where is added sugar, cocoa powder and other ingredients, being milled for about 4-6 hours at a controlled temperature. In the first part of the process the tank is heated then cooled by tap water. After milling the chocolate is transferred to the chocolate storage tank. Fat melting tank 540l heating by water jacket and electrical resistor heated grid with 250l beneath the grid volumetric dosing pump controlled from switch board 0.55 kw, app. 200 rpm stirrer 13.1 kW - installed power 2 x 6 kW = 12 kW - heating resistors 0.55 kW water circulation pump stainles steel filter heated fat dosing pump Ball refining tank 500l working ca ...

Fully automatic hardening line consists of: 1x hardening furnace with salt bath LLF-8/G/X-S (gas-heated) 2x tempering furnace FVF-8/E/X-R (electrical heated) 1x tempering furnace FVF-8-G/X (gas-heated) 1x washing machine WCF-8/X/3/E-R (electrical heated) 1x fine filter for wasing machine 1x desalination plant DS-80/E for washing machine 1x salt transfer container (salt storage for hardening furnace) 1x magazine with loader and unloader 1x transport roller conveyor 2x lift table (charge and discharge) 1x extractor hood over the entire length of the driveway 1x cooling place

salt bath hardening system, make: IOB almost unused with charging dimensions 800 Ø x 1200 mm heating type: gas/electric consisting of: 2 loading places 3 electrical heated pre-reheating furnaces 500°C 4 gas heated crucible furnaces 900°C 1 electrical heated thermal bath 450°C 1 electrical heated washing tank (3-fold) 1 air cooling tank 1 water drainer 2 unloading places 1 el. measuring, regulating and control system 1 evaporator 1 intermediate storage tank 1 suction 1 chimney various accessories condition good requird space: approx. 12 x 20 m

Maximum format: 1060 x 770 mm Min. format: 450 x 370 mm max punch format: 1050 Ã? 750 mm Maximum format of embossing: 1050 Ã? 750 mm gripper margin: 8-17 mm paper weights: 90-2000 g / m2 (carton) 0.1-2 mm (box)? 4 mm (corrugated board) maximum punching force: 300 T Maximum speed: 7500 sheets per hour Max marking speed: 6500 sheets / hour individually heated zones: 12 heated zones (each zone can be heated independently up to up to 200 degrees) Max Folienlängsdurchmesser: 250 mm maximum stack height display: 1200 mm maximum stack height investors: 1350 mm Main motor power: 11 kW Machine power: 46 kW Weight: 17,000 kg Air requirement: 0.6 MPa, 0.37 m3/min Dimensions: 6050 x 4200 x 2260 mm

The teedwater is pre-heated in the exchanger E009, by steam condensation coming trom the last column, and in the pre-heaters F004-F001 by condensate produced in every effect. The teedwater evaporates partially in the first column (E001) as heated by industriai steam. The industriai steam passes through the pre-heater F001 and is drained by steam trap ST001. The produced pure steam trom the top and the water not evaporateci trom the bottom 1 -pass to the tollowing effect, where the process is repeated at lower pressure and temperature. The distillate produced by pure steam condensation goes to the pre-heater F002. The process is repeated for all columns in the same way. The steam produced in the last effect is condensateci and cooled together with the distillate coming from pre-heaters in the exchangers E009 and E01O, by teed and cooling water. 1 - SINGLE EFFECT RUNNING DESCRlBTION ...

Beer Brewery Two Vessel VELO 15hl/brew, two brews/day, up to 4000hl/annum Complete two vessel beer brew line made by Italian VELO (currently TMCI Padovan) suitable for various beer types from ALEs to LAGER’s, non-alcoholic beers to strong, over 10% Imperial Stouts. Normal brew size has been 1500 liters and during high season, they have brewed 2 brews during 10-hour day. Maximum batch of malt is 600 kg. Without adding sugar beer wort has been from 18.5 to 21 Plato and with sugar added, up to 35 Plato. One complete brew batch with CIP will take about 5-6 hours. In operation, this brewery has overlapped brew batches so that once the first batch of the day has been lautered and spend grain has been unloaded, they started next brew. Maximum weekly brewing capacity with 10 hour working days has been 6 brews (3x3000 liters CCT) due to fermenting tank capacity which leads to theoretical 40 ...

Overview The micro brewery was manufactured in 1999 by theGerman manufacturer BERAPLAN. All equipment is in good condition. A new wort copper was added in 2018.  List of equipment: 1. Mash Tun Made by Beraplan in 1999 Cylindric shape with conical ground Material: stainless steel AISI 304 Inner diameter: 2000 mm Height: 1600 mm Height conical part: 20 0mm Volume: maximum 38 Hl Double sidewall Insulation Heated by steam, which can be regulated Hot and cold water inlet at the bottom Can be emptied through the bottom 4 CIP balls PT100 2 agitators Mach pump with variable speed drive 2. Lauter Tun Made by Beraplan in 1999 Cylindric shape with flat ground Material: stainless steel AISI 304 Inner diameter: 2000 mm Height: 1200 mm Volume: maximum 37 Hl Filtering ground with trapezoidal perforations High precision valve to regulate the flow rate Hot and cold water inlet at the bottom 4 CIP ball ...

Bank of 4 x Upstroke Presses With pump unit Consisting of 2x Thompson 120ton Upstroke Press 600mm sq. electrically heated platens 12” diam. ram Digital controllers Solid state relay temperature controllers 1x Thompson 150ton Upstroke Press 600mm sq. electrically heated platens 14” diam. ram Digital controllers Solid state relay temperature controllers 1x Dixon 180ton Upstroke Press 600mm sq. electrically heated platens Ram in excellent condition Cure timers Automatic process controller Solid state relay for heating

Aseptic Production and Filling Line for Non-Carbonated Drinks 2500 bph This production line is designed for the preservative-free production and bottling of all kinds of heat-treatable, non-carbonated soft drinks, e.g. vitamin drinks, filtered/low-fiber juices, tea-based drinks (brewed from real leaves), plant-based milks/drinks, etc. This line is used for green tea based drinks, flavoured with various fruit juices. Production equipment includes two tea brewing vessels, mixing tanks, UHT pasteurizer, product filter, water treatment plant with reverse osmosis, oxygen generator and product tank which are the part of the delivery. UHT pasteurizer is heated with thermal oil boiler. The filling line is semiautomatic (blow moulder operation, empty PET bottle feeding and palletizing is made manually). Current owner designed the line from individual machines and rebuilt aseptic filling block ...

Throughput capacity: 600 litres/h, in the process the product (milk, cream, liquid egg, ice cream mix, etc.), which has been heated to 65° C in the counterflow, is heated to 130° C by steam injection in less than a second. The process heats the product (milk, cream, liquid egg, ice cream mix, etc.), which has been heated to 65° C in the counterflow, to 130° C in less than a second by steam injection and then cools it again in the shortest possible time by evacuation, further cooling is achieved by the inflowing product in the counterflow and ice water, includes feed tank, speed-controlled pumps, homogeniser, preheater, infusion tank, expansion tank, steam condenser, cleaning agent tank and other elements, on-site inspection is possible.

"PAWERT" SPM I-90/200 Manufactoring in 1992, reconditioned in 2016 Mechanical single head crank-type Briquette Press for continuous Heavy Duty operation. - Capacity: 2,650 Lbs/Hr (1,200 kg/Hr) depending on raw material quality. Briquette dimensions: 3-1/2" (90 mm) dia.; 3/4" to 11-3/4" (20 - 300 mm) length. Main drive: 75 HP (55 kW installed). High quality welded steel construction. Belt driven flywheel drive. Pre-Heated oil Chamber. This press has (200) press strokes per minute forcing the material through an extrusion chamber to produce uniform material at a high pressure; significantly reducing the volume from of chips/dust to a densified log. This line also has: fully automatic cutting saw control box. < Conveyor Belt. KALLFASS UNIVERSAL Type "600" Shrink Tunnel for packaging. The PAWERT Press was reconditioned in 2016 This is a complete line. it just needs the ...

MTI P-10 laboratory mixer The laboratory mixer is suitable for mixing, homogenizing, dispersing and suspending of low-to high-viscosity products, heated, pressure and vacuum resistant Heating cooling jacket 5 bar Product space-1 / 0.75 bar Tank 15 l, Volume 11 litres. The machine includes two containers heated, presses a vacuum pump and a dispensing device to high-viscosity products from the mixing container. The documentation is available.

LAMINATING SYSTEM POLYTYPE BB 2200 LAMINATION LINE Coating/- lamination equipment for solvent based resin system. On an existing film or composite material. Year: 2008 Condition: Excellent The different film thicknesses what can be used depending on the materials, see references: Plastic foils 25-250 microns Metal foils (copper, aluminium) 20-150 microns Total composite thickness max. 500 microns Machine data: Production speed 0 - 150m/min Production speed 840 - 2160mm Resin 1 - 40g/m2 Winding units (main winder-/ lamination winder-/tensilized film winder): For unwind of the base film there are two winders (main winder/ lamination winder). Winder performance: - Winding direction clockwise / anticlockwise - Brakes ystem for constant and regulated tension e.g. alu foil with max. 2000 kg roll weight - Roll system centerless for steel,plastic-, carton tubes with optimal  ...

Horizontal vacuum bucket dryer mixer Knea dryer 7000 ltr. Used Double-walled vacuum mixer/dryer with heated wall and heated inner tube. With outlet opening, filling dome and service lid, for efficient drying, thickening of products and (contaminated) waste sludge waste. Built: 1997, is currently being regenerated Volume: 7,000 litres Temperature: 151°C Pressure / vacuum 5 bar / - 1 bar (according to pressure gauge), vacuum pump and electric boiler can be offered, as well as up to the customer-specific system Gearbox output speed: approx. 42 rpm (i = 32.8) Transmission power (1,400 rpm): 50 kW Mixer chamber: approx. 1,600 x L 4,400 mm Total dimensions: approx. 6,600 x 2,200 x 3,600 mm Changes and errors in the technical data, data and prices and intermediate sale reserved.

Cooling screw trough screw double-walled heated or coolable used Manufacturer: BARL Maschinenbau GmbH Type: KT0803F17T50 Built: 2015 Total dimensions of the trough screw approx. 9.5 x 1.3 x 1.6 m Trough length approx. 8000 mm Trough width outside approx. 450 mm Trough depth approx. 600 mm Conveyor length approx. 7000 mm partly double-walled and can be heated or cooled with water Steel screw with cooled shaft Spiral thickness approx. 8 mm Diameter approx. 400 mm Spiral height approx. 100 mm Slope approx. 160 mm Shaft approx. 200 mm geared motor 1.5 kW 6.8 rpm 220/380 V substructure Steel construction approx. 11 x 2.5 x 0.2 m Total dimensions: approx. 11 x 2.5 x 2 m Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

Electrically heated furnaces with conveyor belt (for non-explosive substances) TECHNICAL DATA temperature max.: 420°C working temperature: approx. 350°C total power consumption: 60 kVA heating power: 48 kW drive: 0,55 kW air circulators: 2 x 4 kW number of control groups: 2 external dimensions (approx.): length: 8500 mm width: 1800 mm height: 2625 mm useable dimensions: conveyor belt width: 900 mm clear height: 150 mm heated length: approx. 7200 mm

Volcanoring MATEC V.1.0 The inventor and developer of the Volcanoring has been dealing with logs and their pyrolytic burning for 40 years. By installing a log firing system with heat exchanger in his house, he got to know the primary and secondary air ducts for optimal burning of wood with minimal smoke development and minimal ash accumulation. On this basis, Ari Schär developed the Volcanoring with comparable properties for wood burning. This grill draws the air via an adjustable hole system in the base area of the bowl. The incoming air is preheated by the heat radiation downwards before it comes to the fire. As a result, the wood burns off at a temperature of around 1000°C and leaves very little ash with little smoke development when the burning temperature is reached. When firing, the smoke development is correspondingly greater than when the operating temperature is reached ...

Volcanoring MATEC mini The inventor and developer of the Volcanoring has been dealing with logs and their pyrolytic burning for 40 years. By installing a log firing system with heat exchanger in his house, he got to know the primary and secondary air ducts for optimal burning of wood with minimal smoke development and minimal ash accumulation. On this basis, Ari Schär developed the Volcanoring with comparable properties for wood burning. This grill draws the air via an adjustable hole system in the base area of the bowl. The incoming air is preheated by the heat radiation downwards before it comes to the fire. As a result, the wood burns off at a temperature of around 1000°C and leaves very little ash with little smoke development when the burning temperature is reached. When firing, the smoke development is correspondingly greater than when the operating temperature is reached.  ...

Volcanosquare MATEC The inventor and developer of the Volcanoring has been dealing with logs and their pyrolytic burning for 40 years. By installing a log firing system with heat exchanger in his house, he got to know the primary and secondary air ducts for optimal burning of wood with minimal smoke development and minimal ash accumulation. On this basis, Ari Schär developed the Volcanoring with comparable properties for wood burning. This grill draws the air via an adjustable hole system in the base area of the bowl. The incoming air is preheated by the heat radiation downwards before it comes to the fire. As a result, the wood burns off at a temperature of around 1000°C and leaves very little ash with little smoke development when the burning temperature is reached. When firing, the smoke development is correspondingly greater than when the operating temperature is reached.  ...

Process tank 450 l · vertical tank · pressure tank up to 2 bar · main tank made of stainless steel AISI 316Ti · tank insulated with mineral wool with a thickness of 50 mm in the cylindrical part and on the bottom end outer jacket made of stainless steel AISI 316Ti, thickness 2mm · bottom and top bottom pressed DIN 28011 · heating jacket for glycol · circulation pump · heating medium temperature sensor · expansion vessel of the heating system electric heaters - 5 pcs. 4.5kW/400V · control box: controlled by the heating system and the operation of the stirrer · heating medium supply connector DN33.7 · connector for receiving the heating medium DN33.7 Equipment: · manhole DN300 (2 bar) with a safety sensor drain connection (heated) filling connector (heated) · filling level sensor connector · PT-100 temperature level connector · safety valve · Redox + e ...

Continuous ageing furnace, make VEI-Engineering type: KADL 2 120 x 240 tracks: 2 furnace output: approx. 2.000 kg/h gross heating zones: 2 gas heated, 3 electrically heated max. temperature: 280°C working temperature: 180 - 200°C useable dimensions (l x w x h): 15.250 x 2.530 x 2.200 mm external dimensions (l x w x h): 28.500 x 5.800 x 6.200 mm