guillotine used for sale

Hydraulic sheet metal cutting guillotine from Safan Netherlands type VS306, 3100 mm x 6 mm (ST40). The machine has a variable inter-knife gap, and a hydraulically variable knife angle of 0,5 -2 deg. 11 kW motor. The weight of the machine is 6,3 t. The machine is fast. Departure of the bumper 1050 mm. Electrically adjustable cutting length in the range of 10-3100 mm. 2 supports for supporting sheet metal at the front of the machine, gauge of 2500 mm, for cutting at an angle of 90 degrees. Light dash for cutting along the line. Original DTR documentation and safety instructions in Polish.

Hydraulic guillotine for cutting sheet metal by Safan the Netherlands, type VS 255-10, 2550 mm x 10 mm (ST40). The machine has a quickly changing knife gap with thickness reading, and a hydraulically variable knife angle of 0.5 -2 degrees. 11 kW motor. Machine weight 8.2 tons. NC electric bumper with position transmitter with readout, bumper travel 1050 mm. Electrically adjustable cutting length in the range of 30-2550 mm. 2 x supports for holding sheets of metal at the front of the machine, plus a 1500 mm ruler for cutting at an angle of 90 degrees. Light line enabling line cutting. The knives are sharp, the machine cuts copier paper. Original DTR documentation

Hydraulic guillotine for cutting sheet metal from LVD Belgium type HSL 31/6 3100 mm x 6 mm (ST40). The machine has a variable knife gap and a hydraulically variable knife angle of 0.5 - 2 degrees. 9kW motor. Machine weight 4.2 t Bumper departure 750 mm. support for supporting metal sheets at the front of the machine, - ruler 2500 mm long, for cutting at an angle of 90 degrees Original DTR documentation and health and safety instructions in Polish.

Hydraulic guillotine for cutting sheet metal by ESPE Strojarne Piesok, type CNTA, 3150 mm x 6.3 mm (ST40). The machine has a variable knife gap and a hydraulically variable knife angle of 1 -2.5 degrees, set from the desktop. 11 kW motor. Machine weight 7 tons. Bumper departure 950 mm. Electrically adjustable cutting length in the range of 10-3150 mm. 2 supports to hold sheets of metal at the front of the machine, plus a ruler for cutting at a 90-degree angle. Light line enabling line cutting. Original O&M documentation and occupational health and safety manual in Polish. The machine is designed for continuous operation - 3 shifts.

Hydraulic guillotine for sheet metal cutting by Beyeler Switzerland type VR 10-3070, 3070 mm x 10 mm (ST40). Cybelec DNC10 PS fully CNC controlled machine. The machine has a variable gap between the knives and a hydraulically variable knife angle of 1 - 2.5 degrees, set after entering the thickness and hardness of the material. 18kW motor. Machine weight 9 t. Super-fast bumpers - 1050 mm bumper departure. Electrically adjustable cutting length in the range of 10-3070 mm. 2 supports to support sheet metal at the front of the machine, plus a 90 degree cutting gauge. Light line for line cutting. Original DTR documentation and health and safety instructions in Polish. Infrared protection of the rear working area. The machine is designed for continuous operation - 3 shifts.

Hydraulic guillotine for cutting sheet metal from Darley the Netherlands, type GS 3000-10, 3050 mm x 10 mm (ST40). The machine has a variable knife gap and a constant knife angle of 1.5 degrees. 18 kW engine. Machine weight 9 tons. Electric bumper - bumper departure 950 mm. Electrically adjustable cutting length in the range of 10-3050 mm. A machine with very small external dimensions. A support for holding sheets of metal at the front of the machine, plus a ruler for cutting at a 90-degree angle. Original O&M documentation and occupational health and safety manual in Polish. The machine is designed for continuous operation - 3 shifts.

Hydraulic guillotine for cutting sheet metal by Safan the Netherlands, type VS 310-3, 3100 mm x 3 mm (ST40). The machine has a quickly changing knife gap with thickness reading, and a hydraulically variable knife angle of 0.5 -2 degrees. 5.5 kW motor. The weight of the machine is 4.2 tons. The machine is fast and the number of cuts is equal to that of mechanical ones. CNC electric bumpers with a position transmitter with readout, bumper travel 1050 mm. Electrically adjustable cutting length in the range of 75-3100 mm. A system for magnetically supporting large sheets of metal while cutting at the rear of the machine. Support 2000 mm angle bracket, to support sheet metal at the front of the machine. Light line enabling line cutting. Original DTR documentation.

Hydraulic press brake: HACO Belgium type Euromaster ERM 300-200, rb: 2000/2022. Bending length: 3100 mm; Between columns: 2650 mm Loading: 250 mm, stroke 200 mm; Pressure: 200 t Kvara ESA S630 CNC-controlled press, Windows, graphics, Polish language, 2D simulation. Hydraulic guillotine for cutting sheet metal by HACO Belgium, type HSLX3013, 3100 mm x 13 mm (ST45), rb. 2001, CE compliant. SC7 CNC control. The machine has a quickly changing gap between the knives with CNC-controlled sheet thickness reading, and a hydraulically variable knife angle in the range of 1-3 degrees. Full Operation and Maintenance Manual, BiHP position manual in Polish.

The machine has a quickly changing knife gap with sheet thickness reading and a constant knife angle. 9 kW motor. Weight 4.5 tons. Electric bumpers with reading, bumper departure 850 mm. Supports for supporting sheets of metal at the front of the machine, with a ruler for cutting at an angle of 90 degrees. Original O&M documentation and occupational health and safety manual in Polish. The guillotine cuts sheet metal from 0.8 to 6 mm. The machine is functional, the cutting knives are 90% new.

Reinforced version, for 3-shift work. CNC SC5 control. The machine automatically sets both the angle and the gap after entering the material thickness. The machine has a quickly changing gap between the knives with CNC-controlled sheet thickness reading, and a hydraulically variable knife angle in the range of 1-3 degrees. 7.5 kW motor. Weight 6 tons. Electric bumpers with CNC position reading and setting, bumper travel 1050 mm. The bumper has a retraction function. Supports to hold sheets of metal at the front of the machine, with a ruler for cutting at an angle of 90 degrees. Original O&M documentation and occupational health and safety manual in Polish. The guillotine cuts sheet metal from 0.8 to 6 mm. The machine is functional, the cutting knives are 90% new.

Cutting length: 3100 mm x 6 mm, full CNC control. Variable knife angle and knife gap, set by the computer after entering the gr. and length of the material. Cutting sheet metal in the range of 0.4 - 6 mm. CNC stop, departure 10 -1050 mm, retraction, programs. Machine with automatic support of long sheets of cut sheet metal at the back. Liftable rear bumper. Machine weight 6.5 tons. 2 supports and an angle bracket at the front of the machine. The only guillotine on the market up to 6 mm, with such a low demand for electricity, main engine only - 5.5 kW. Full original Operation and Maintenance Manual in English and Polish, BiHP position manual in Polish. The machine is hardly used, cutting knives are 95% sharp.

sheet width: 3050 mm plate thickness: 16 mm distance between columns: 3050 mm : 15-1000 mm cutting angle adjustment: ja ° cutting gap adjustment: ja mm connected load: 30 kW weight of the machine ca.: 14,.5 t dimensions of the machine ca.: 4,0 x 4,0 x 2,55 m Hydraulic guillotine shear with - ELGO control for backgauge - Cutting angle adjustment - Cutting length adjustment - Cutting length limitation (time dependent) - Sheet thickness adjustment - Back gauge with clearance function - Cutting line lighting - Side stop - 3 pcs. support consoles - good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Guillotine Make Polar Model 78E Year 1995 Cuttinglenght 780 mm Details Hydraulic clamp Electric cutting Electric backgauge adjustment Digital read/out + programming

Guillotine Make Eba Model 551LT Year 2003 Cuttinglenght 550 mm Details Digital Program with keypad Light curtain Hydraulic adjustable clamp Air table, side tables Single phase 240V Available soon after order

Schechtl MSC 310/BV - Motorized guillotine shears - double-edged steel knives - Tool-free cutting gap adjustment - Angle stop 1000 mm left & right - Support arms 1000 mm - Manual depth stop 0-750 mm - Analogue position display - Automatic hold-down device - pneumatic tilting table (clippings tray at the front) - Maintenance-free scenery guidance - Year of construction 2001 Specification - Working length: 3165 mm - Capacity steel (400N/mm²): 3 mm - Capacity aluminium (250N/mm²): 4.5 mm - Capacitance VA (600N/mm²): 2 mm - Dimensions WxHxD: approx. 3700 x 1500 x 2300 mm - Weight: approx. 3000 kg

sheet width: 2040 mm plate thickness: 3.0 mm thickness at Niro-steel: 1.5 mm no. of strokes: 50 Hub/min cutting angle: 1.4 Grad table height: 750 mm distance between columns: 2120 mm back stop - adjustable: 1.0 - 550 mm column arm: 100 mm Control: manuell engine output: 5.5 kW weight of the machine ca.: 2050 kg. range L-W-H: 2600 x 1980 x 1400 mm Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display adjustable from the front Continuous adjustment over the entire travel range Adjustment range 1.0 - 550 mm - Machine side stand with projection .. 100 mm - manual cutting gap adjustment - 1x hold-down bar - 1x long side stop - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - 2x EMERGENCY stop buttons at the front -  ...

sheet width: 2540 mm plate thickness: 2 mm strokes per minute until: 63 throat: 100 mm cutting angle: 1,13 ° table height: 750 mm table width: 320 mm table height over floor: 750 mm total power requirement: 3 kW weight of the machine ca.: 1600 kg dimensions of the machine ca.: 3,1 x 2 x 1,3 m Electric 380 Volt: Rear register front operated: 15 - 550 Foot switch: Squaring arm: Support arms: 3 x Motorized guillotine shears in the swing cutting system with adjustable from the front manual backgauge with analogue display and reading optics. Power transmission via gearbox, eccentric shaft and connecting rod on the cutter bar. Less noise level because the gear is only switched on during the cutting process is. Hold-down beam with continuous pressure element made of elastomers material that ensures secure clamping of the sheet metal. The cutting performance refers to 400 N/mm² strength. Ma ...

Used pastry line CANOL, type: Canolino 5.2 -in bakery condition- - Calibration unit -Filler - Cutting station - Folding device -Guillotine - various tools Viewing and test run are possible by arrangement.

1 x Perfecta 115 TVC guillotine 1 x Perfecta SA 110 A jogger

sheet width: 3050 mm plate thickness: 12.0 mm ST plate thickness: 8.0 mm VA no. of strokes: 7 - 14 Hub/min down holder: 18 Stück cutting angle: 0.5 - 3.0 ° work height max.: 930 mm back stop - adjustable: 1000 mm Control: SP 8 total power requirement: 22.5 kW weight: 8500 kg range L-W-H: 4180 x 2030 x 2210 mm Furnishing: - electro-hydraulic & slide-guided guillotine shears - including HACO NC machine control SP 8 Pre-selection positioning from the backgauge Digital display of actual value Electro-hydraulic cutting angle adjustment with digital display programmable retraction from the backgauge Programmable cutting length limit Emergency switch - electro-motorized back gauge, on ball screws - manual cutting gap adjustment, adjustable from the rear - Finger protection at the front - 1x side stop .. 1.000 mm - Protective device behind the machine - rear sheet metal slide - 1x freely ...

Guillotine Make Polar Model 92EM Year 1985 Cuttinglenght 920 mm Details Cutting with program currently not possible, other than that normally functioning Airtable Digital read out Available direct

Guillotine Make Horizon Model APC-T61 Year 1997 Cuttinglenght 610 mm Details Hydraulic cutting Hydraulic clamp Digital readout + programming Light curtain safety Available direct

sheet width - max.: 2035 mm plate thickness: 6.0 mm ST plate thickness: 4.0 mm VA plate thickness: 8.0 mm ALU number of strokes - loaded: 20 Hübe/min cutting angle: 1.7 ° work height max.: 900 mm Number of working hours: 1.450 h Control: LENORD total power requirement: 11.0 kW weight of the machine ca.: 4100 kg range L-W-H: 2416 x 2250 x 1760 mm Machine from prototype construction Machine with only approx. 1.450 operating hours () Furnishing: - electro-hydraulic guillotine shears - electro-motorized backgauge with NC control unit (Lenord + Bauer) - electrical cutting length limitation - manual cutting gap adjustment - 1x stable side stop, with scale and tilting cam - 2x front support arms - 1x freely movable foot switch - Operating instructions (PDF) + circuit diagram Special accessories included: - pneumatic sheet metal holding device for thin sheet metal cuts Machine link: http: ...

Semi automatic edge bander Make: VITAP Type: FUSION 2.0 New machine Technical datas: - For straight and shaped pieces 10 - 60 mm - Edge thickness 1-3 mm - Tefloned gluing station with quick disassembly system - Glue and tape application on big and small shaped panels - Equipped with glue pot with 1 Kg capacity - 1 glueing roller - 2 rollers to copy the shape of the piece - 1 tilting support roller to enable the exit of the panel after banding - Glue application amount is adjusted via knob - Set up of the glue temperature - Automatic guillotine for coiled material up to 3 mm x 45 mm THREE KIND OF WORKS: - By Encoder - By Encoder + laser - By Pedal cut Panel materials - Solid wood - Chipboard (laminated or not) - Multilayer material - MDF or HDF (laminated or not) - Panel dimensions range: min 50x200mm max 1000x2000 mm - Shaped pieces Dimensions ran ...

Hot melt contour edge bander Make: VITAP Type: SMART New machine For straight and shaped (convex or concave) pieces - To glue pieces 10-60 mm thickness, - PVC / melamine / veneer / plastic / laminate / solid wood - Edge 0,5 - 3 mm - 1 glue spreading roller 10-60 mm thickness - Guillotine to cut bands up to 3 mm thickness - 2 tape feeding speed (3m/min or 7 m/min) - Tape plate d=520mm - Glue pot 1kg capacity Solid Phenolic table - Easy to clean - No transmission of heat - Plastic cups to raise the piece above the table. So the panel weight is not focused on the glued band. - Electronic temperature control - Foot pedal cutting system - CE standards Optional for an extra charge available - Vitap glue 2 kg - Vitap glue 10 kg

Contour edge bander Fabrikat: VITAP Type: BC91 EVO New machine Max. flexibility by means of a smart construction - For gluing chamfers on rectangular or formed workpieces - Tilting table 0°-45° - To glue pieces 10-60 mm thickness - Edge material: PVC, melamine, veneer, plastic, laminate, solid wood - Nr. 2 glue spreading rollers - Cutting guillotine up to 3 mm thickness - Glue pot (kg 3), with electronic adjustable heating system - Band length measuring by means of a digital electronic counter - Tape cut by foot pedal to edge just one piece and measuring edge length - Feeding speed adjustable from 7m to 20m per min. Solid Phenolic table - Easy to clean - With no transmission of heat - Plastic cups to raise the piece above the table - 2 kg vitap glue 280.00 for test - CE standards Optional: - Enlarged tape plate 800 mm - Semi-automatic end-c ...

Contour edge bander Fabrikat: VITAP Type: BC91 EVO Demonstration machine Technical data: - For straight and curved pieces (convex and concave) - To glue pieces thickness 10-60 mms., in PVC, melamine, veneer, plastic laminate and solid wood - 2 glue spreading rollers - Cutting guillotine up to 3 mm. thickness - Encoder for high precision cutting of the tape ( for shaped closed pieces) - Band length measuring by means of a digital electronic counter - Tape cut by foot pedal to edge just one piece - End switch tape cut (only for straight pieces) - Feeding speed adjustable from 3mt to 20mt per min. - Solid Phenolic table easy to clean and with no transmission of heat - Manual / Automatic band cutting device - Glue pot (kgs. 3), with electronic adjustable heating system -Tilting table 0°-45° - Standard accessories - CE standards

Bun Line König Artisan SFC Year of construction: 2013 Condition: checked & cleaned Suitable for making ciabatta and square buns Hourly capacity: max. 300 kg of dough Dough belt height: min./ max. 12mm/ 32mm, dough dependent Dough belt width: 170 mm Flour duster for top and bottom side Guillotine and punching unit for high product variety Touch panel with recipe management Seeding station with water bath, type: MOC-C300 Incl. 3 cutting rollers for 1 to 4 rows operation Incl. 2 punching tools (see pictures)

Bun Line König Artisan SFC Year of construction: 2011 Condition: checked & cleaned Suitable for making ciabatta and square buns Hourly capacity: max. 300 kg of dough Dough belt height: min./ max. 12mm/ 32mm, dough dependent Dough belt width: 170 mm Flour duster for top and bottom side Guillotine and punching unit for high product variety Touch panel with recipe management Seeding station with water bath, type: MOC-C300 Incl. 3 cutting rollers for 1 to 4 rows operation Incl. Rhombus punch for one or more rows operation Incl. Triangle punch for 2 row operation

Max. Coil weight: 25t, max. Coil outer diameter: 2500mm, Coil inner diameter: 506-610mm, Finished sheet width: 50-159mm, Strip thickness: 0.6-3mm, with double cone decoiler, threading assembly, straightener (straightener was taken over from an earlier line, Schnutz factory, year of manufacture late 80s - early 90s), loop bridge, strip feed unit, cut-to-length shear, conveyor belt, brush table with gripper, slitting shear (guillotine shear), conveyor belts, stacking unit and gantry gripper with two stacking stations, on-site inspection is possible.

Chip tape for cutting machines Busch SF 130/25-225; good condition; cleaned and tested; Conveying height 1300mm; Transport length 2250mm; Bandwidth 250mm; Speed 0.4m/s. Waste conveyor for Guillotines Busch SF 130/25-225; good condition; cleaned and checked; conveying hight 1300mm; lenght og delivery chute 2250mm; Band width 250mm; Speed 0.4m/s.

Multivac R 230, year of manufacture 2001, film width 355 mm, draw-off length 210 mm, free loading section of 1,6 m, MC96II control with LCD monitor, 10 mm side trim, two cross-cut guillotines, height-adjustable discharge conveyor, central chain lubrication, new servo inverter for chain feed, Vario tool with interchangeable formats. Format: 1.1 . 335 mm x 210 mm 2.1 - 167.5 mm x 210 mm 2.2 - 167.5 mm x 105 mm 3.1 - 111.66 mm x 210 mm Total length of the machine 5,15 m Operational and wear parts replaced.

Neue Glaslineale - New Glass Rule Polar 72-82-90-115 Year 2014 for the following guillotines: Polar 72 Polar 82 Polar 90 Polar 115 -Online-Video-Inspection by Skype-Video- -We would be very pleased with your visit - more machines on Stock- -Available Immediately - Can be inspect- -On Stock Emskirchen / Nuernberg - Can be test-

A prototype machine for cutting, dressing and cooling fruit, e.g. apples, pears. For example, apples and pears are cut into 8 or 12 segments with manual guillotines (2 pieces). The fruit falls into the bathtub, EQUIPPED with a glycol cooling system (coil installed), the belt speed can be changed, and 2 guillotines can work in the bathtub at the same time. Capacity up to 900kg/h, speed regulation. Built-in coil - Possibility to connect a cooling agent. Built-in circulation pump. The cut fruit falls onto a conveyor belt, which transports the cut fruit to the washing and cooling water, where it is removed from the liquid on a second belt. Minimum soaking time 3 minutes. Additionally, a temperature controller (Danfos programmer) is installed. Year of production 2015. 100% efficient with a VERY EFFICIENT cooling system. The guillotines are German devices manufactured by FEU ...