137,870 used machines on RESALE, but how to find them? Machine Search
QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed is adjustable to change throughput rate 500 to 1.000 kg/h, throughput rate can be adjusted according to contamination and material, Low water consumption (depending on contamination) About 60 lt., The water can be mechanically filtered with a [water screening system](.germanplast.eu/listings/5003567-germanplast-vibrating-screen- for-water-powder-granule) (available separately) to be reused in the proces ...
grinding length: 800 mm grinding width: 400 mm workpiece height: 375 mm table surface area: 840 x 400 mm table speeds: 0,005 - 35 m/min spindle speeds (infinitely variable): 1000 - 3000 U/min grinding wheel motor: 3,7 kW grinding wheel size: 300 x 50 x 76,2 mm cross adjustment: 100 - 1250 mm/min rapid traverse vertical: 180 mm/min table load: max. 700 kg distance spindle center to table: max. 525 mm total power requirement: kW weight of the machine ca.: 2,8 t dimensions of machine L x W x H: 3,14 x 1,78 x 2,50 m Accessories: magnetic plate 800 x 400 mm, grinding wheel with flange, wheel dressing attachment, wet grinding attachment with paper band filter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
AUTOMATIC VERTICAL BINDING BALER, for FILM, WOVEN PP, PET, RIGID AND SOFT PLASTICS, PAPER, CARDBOARD and more, 80 Tons ca. pressing force, 45 kw drive, complete with oil heating and cooling systems, proportional pressure flow controller, Bale size LxWxH 1.100x720 mm (adjustable length), feeding hopper size : 1.100 x 1.600 mm., Average throughput rate, - with 30 kg/m3 materials 5-7 Ton/h, - with 50 kg/m3 materials 9-11 Ton/h, - with 120 kg/m3 materials 17-19 Ton/h, 5 vertical-wire binding, Cycle with no material, no twisting : 25 ca, Pre-press flap with 2 x 20 Ton force, Exchangeable bottom plate in hardox in channel and chamber, oil tank capacity 950 lt., Machine weight ca.25.000 kg., General features, common to all balers:, Construction ìn sturdy carbon steel with top EU components., Compact and easy to use, Automatic binding, Fully automatic with adjustable parameters on touch screen ...
CROSSED MIXING SYSTEM FOR PLASTIC MATERIALS, The system includes n.2 x 20.000 lt. vertical mixers which fill each other through the endless screw conveyor. (ask for different capacities), for each mixer :, total height approx 6.950 mm including transmission group, max diam. 2.380 mm.(standard transport), constructed in painted electro-welded carbon steel., inner auger diam.350 mm., lower hopper with safety grid and sampling shutter, complete with anti-dust cover, mm.600×500, pulley and belt transmission, protected by carters (possible gearbox, instead), inspection doors with safety limits, cleaning hinged door with on bottom of cone for complete discharging, with safety opening, bottom discharging pipe on the other mixershopper with pneumatic valves, side discharging pipe to big bag with valve mm.at 2.700 mm from ground with pneumatic valves, electric min/max level indicator, paddle typ ...
AUTOMATIC VERTICAL BINDING BALER, for FILM, WOVEN PP, PET, RIGID AND SOFT PLASTICS, PAPER, CARDBOARD and more, 100 Tons ca. pressing force, 45 kw drive, complete with oil heating and cooling systems, proportional pressure flow controller, adjustable channel pressure, Bale size LxWxH 1.100x720 mm (adjustable length), Filling hopper size 1.100 x 1.600 mm., Average throughput rate, - with 30 kg/m3 materials 6-8 Ton/h, - with 50 kg/m3 materials 10-12 Ton/h, - with 120 kg/m3 materials 18-20 Ton/h, 5 vertical-wire binding, upper and lower photocells to control material feeding feeding, Cycle with no material, no twisting : 22 ca, Pre-press flap with 2 x 20 Ton force, Exchangeable bottom plate in hardox in channel and chamber, Baler weight ca.27.000 kg., General features, common to all balers:, Construction ìn sturdy carbon steel with top EU components., Compact and easy to use, Automatic bind ...
AUTOMATIC VERTICAL BINDING BALER, for FILM, WOVEN PP, PET, RIGID AND SOFT PLASTICS, PAPER, CARDBOARD and more, 120 Tons ca. pressing force, 90 kw drive, complete with oil heating and cooling, proportional pressure flow controller, Filling hopper 1.100 x 1.600 mm., Bale size LxWxH 1.100x720 mm (adjustable length), Average throughput rate, - with 30 kg/m3 materials 6-8 Ton/h, - with 50 kg/m3 materials 11-13 Ton/h, - with 120 kg/m3 materials 19-22 Ton/h, 5 vertical-wire binding, Cycle with no material, no twisting : 21 ca, Pre-press flap with 2 x 26 Ton force, Exchangeable bottom plate in hardox in channel and chamber, Machine weight ca 28.500 kg, oil tank capacity : 1.500 kg, General features, common to all balers:, Construction ìn sturdy carbon steel with top EU components., Compact and easy to use, Automatic binding, Fully automatic with adjustable parameters on touch screen panel., A M ...
900 mm sanding machine for turned products. GENINI mod. LAR90 - Maximum working length 900 mm. - Automatic loader
Control amplifier, servo motor control, power controller, thyristor power controller, thyristor controller, power regulator -Manufacturer: Gefran, power controller power regulator -Type: GTF-25-480 -Number: 5x power controllers available -Price: per piece -Dimensions: 150/60/H135 mm -Weight: 0.9 kg/pc.
LIFTING AUGER, for regrinds, box housing mm.400 outer Ø, internal spiral 300 mm Ø, bearings with dust protection, Length 8,5 mt., Collection hopper 900 x 500 mm (or bespoke), exhausting outlet, intermediate supports every 3 mt., Bonfiglioli gearbox, 5,5 kw drive, complete with Users manual. CE compliance and el,.drawings, installed power - used power in work: about 60-65% : 5.5, availability: ca 4 weeks from confirmation, conditions: new machine, type: to collect and lift materials
Tool holder, milling holder, chuck, milling tool, adapter, clamping unit, tool holder, collet sleeves -Milling holders: MK4 holder -Type: Ø27 x 60 mm Z 03 1-02 -Dimensions: 245/43/43 mm -Weight: 1.3 kg
1m wide OptiFlour II. Bought new in 2022 and only used for a few months. Almost as brand new condition. Matching OptiAir dust extractor available at extra cost.
door closer, floor door closer, closing body -Manufacturer: Geze, floor door closer closing body type TS 500 NV -Art.No.: 0672-CPR-0121 -Dimensions: 270/70/H65 mm -Weight: 2.8 kg
Delivers smoothly an even batter coverage Provides adhesion for breading Belt width: 600 mm
Smooth and efficient batter coverage to a wide range of products in a wide variety of shapes and styles. Belt Size (mm): 1000 wide
2 x die-sinking EDM machines ZK Genius 700 BJ 1010 and 2019
lever hoist, chain hoist, assembly hoist, assembly chain hoist, pulley block, spur gear pulley block -Manufacturer: GEDI, chain hoist -Load capacity: 3 tons -Hook path: 10 m -Transport dimensions: 700/600/H350 mm -Weight: 114 kg
electric motor, three-phase motor -Manufacturer: ATB Bauknecht, electric motor 100L Ex-protected -Type: EAY 100L/4C-12 -Power: 2.5 KW -Speed: 1420 rpm -Shaft: Ø 28 x 60 mm -Design: B3 -Protection class: IP54 -Dimensions: 365/250/H205 mm -Weight: 25 kg
Electric motor, three-phase motor -Manufacturer: VEM, electric motor type KMR 71 G 2 Ex-protected -Power: 0.8 kW -Speed: 2850 rpm -Shaft: Ø 19 x 40 mm -Design: B3 -Protection class: IP 44 -Dimensions: 250/140/H185 mm -Weight: 11.4 kg
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams, swivel cylinders -Hydraulic cylinder: double-acting stroke 100 mm -Type: DZ25L38/100 GEHV -Piston rod: Ø 25 mm -Holes: Ø 20 mm / Distance: retracted 277 mm -Dimensions: 340/60/H100 mm -Weight: 4.5 kg
Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-
Centrifugal fan NICOTRA - Gebhard type P2M-M3M4J-RRB-ATEX RD/0Fabr. No. 318844/626052/1 Year of construction 2008Volume flow 10000 m³/h = 166 m³/min. Pressure p 1.2 kg/m³Air inlet 500 mmAir outlet 450 x 450 mmEngine speed 1435 rpm. Motor power 4 kWNet connection 400 Volt 50 Hz- Fan wheel with 8 fan blades- Directly flanged drive motor- Mounted adapter ring with flex sleeve 500 mm- Adapter flange for air outlet from rectangular flange 450 x 450 x to 500 mm- Galvanized
Electric motor, three-phase motor -Manufacturer: ATB Bauknecht, electric motor explosion-proof -Type: 180L-4 -Power: 22 KW -Speed: 1465 rpm -Shaft: Ø 48 x 110 mm -Design: B5 -Protection class: IP54 -Dimensions: 700/475/H350 mm -Weight: 219 kg
Distance between points: 1000 mm, Height of points: 180 mm, Max. diameter to be rectified: 355 mm, Max. piece weight between points: 300 Kg, Max. weight with plate: 125 Kg, Transverse travel of the carriage (X axis): 350 mm, X-axis speed: 0.01 / 6.000 mm/min, X-axis Resolution: 0.0001 mm, X-axis measurement system: Digital ruler, Longitudinal travel of the carriage (Z axis): 1.300 mm, Z-axis speed: 0.01 / 15,000 mm/min, Z-axis resolution: 0.0001 mm, Z-axis measurement system: Digital ruler, Working wheel dimensions (od x id x width): Ø500 x Ø203 x 80 mm, Main engine power: 7,5 Kw, Angle of rotation of the grinding head: -30º / +210º, Workhead rotation speed: 10 / 800 rpm, Workpiece holder head cone: MORSE 5, tailstock cone: MORSE 4, Ø of the tailstock shank: 60 mm, Course of the counterpoint reed: 40 mm, Dimensions: 4600 mm Length x 2400 mm Width x 2050 mm Height, Weight approx.: 6. ...
A Büter Hebetechnik GmbH outdoor goods lift is available. Payload: 2000kg, useful stroke: 8160mm, lifting time: approx. 45s, lowering time: approx. 45s, drive power: 6.2kW, stops: 3, ground floor height: 0mm, 1st floor height: 4450mm, 2nd floor height: 8355mm, internal dimensions X/Y: 1500mm/1260mm, largest pallet: CP2. The lift is almost new and was practically unused. Documentation available. An on-site inspection is possible.
Tool holder, milling holder, milling tool, long milling arbor, arbor holder, cutter head holder, cutter head holder -Milling holder: Type SK50 7 pieces -Intake: Ø 50/40/32/22 mm see photos -Transport dimensions: 390/220/H250 mm -Total weight: 27.2 kg
Tool holder, milling holder, milling tool, long milling arbor, arbor holder, cutter head holder, cutter head holder -Milling holder: Type SK50 -Intake: Ø 32 mm see photos -Dimensions: 250/90/H95 mm -Weight: 3.5 kg
Siemens Sinumerik 840D control, incl.: abrasive processing, hydraulic unit and portable loading system for loading and unloading the machine, Technical specifications:, Tip distance: 600mm, tip height: 180mm, maximum grinding diameter: 355mm, maximum workpiece weight: 150kg, maximum Z-axis speed: 11 m/min, minimum Z-axis speed: 0.01 m/min, maximum X-axis speed: 7.5 m/min, minimum X-axis speed: 0.01 m/min, External/internal grinding spindle:, Grinding wheel standard (Øa x b x Øi): 600 x 80 x 304.8 mm, Grinding wheel circumferential speed: 5 - 50 m/s, Power consumption of grinding spindle motor: 11 kW, Workpiece spindle:, Taper bore workpiece headstock: MK 5, Power consumption: 2.7 kW, Tailstock:, Taper hole center point: MK 4, Coolant reservoir: 2000 liters, lubricating oil: 30 liters, hydraulic oil: 60 liters, Operating voltage: 400 volts, 3 phases, Mains frequency: 50 Hz, Total weight ...
TDK GEN20-120-1P230, TDK-Lambda 19 Inch Laboratory Power Supply 44 mm package 0 - 20 V/DC / 0 - 120 A Clocked Input voltage range 85 - 265 V/AC Integrated RS-232 / RS-485 interface External, analogue programming and monitoring Type (general): Rack-mount Item condition: Used, in perfect condition R11B1_EK You can find more laboratory power supplies - new and used - in our shop! International shipping costs on request!
Dividing head, spiral milling attachment, dividing head, dividing head, tool holder for grinding, drill grinding machine, milling cutter grinding machine, drill grinding holder, milling cutter grinding holder -Subhead -Point width: 450 mm -Recording: SK40 - Suitable for: Milling cutter sharpening -Translation: 1:40 -swivel -Weight: 60 kg
Separator GEA Westfalia Type: MSE 100-06-177 Properties: Manufacturer: GEA Westfalia Type MSE 100-06-177 Machines No. 1731-518 Year of construction 2012 Engine power 37 kW Total height 2150 mm Width 1600 mm Length 2000 mm Description: The separator is a cleaning separator to remove solids from milk/juice, etc. No cream separator that separates skim milk and cream! Part 1/3 - Separator Dimensions: Width: 1,600 mm Length: 2,000 mm Height: 2,150 mm Part 2/3 Control cabinet Dimensions: Width: 800 mm Depth: 400 mm Height: 2,100 mm Part 3/3 Tools
Technical data of the steel girder: Manufacturer: Stow Type: Pal Rack NS The scope of delivery includes: 01x Steel beams, used Material colour: orange Box profile: 100 x 50 mm Agraffe: 4 HK (hooks) Overall length: 3,835 mm Note: The steel girders were attached to a length of between 2,700 - 2,800 mm welded on a plate. (Dimensions: approx. 200 x 110 x 50 mm (LxWxH) Since these are second-hand goods, scratches, damage, welds or rust roots! General information about the article: This item is only available for pickup. Any additional transport or shipment of this item is associated with additional costs, which can be requested separately depending on the delivery location or scope of delivery.
Key data: 24 KW, 30 kVA
We currently offer: Number 67 Generator sets Gesan Engine John Deere Power: 30 KVA / 24 KW Hz 50 Year of construction 2003 Operating hours 10654 / 9933 Connection: 32A, 63A, socket Metrics: L: 2.60m H: 1.65m W: 1.10m Weight: 1275 kg Generator set starts but engine does not start You can find more machines on our website. If you have any further questions, please feel free to contact us. Adel e.K. Commercial Vehicles-Construction Machines Car Recycling Machine Dismantling Gottlieb-Daimler Str. 26 D-74831 Gundelsheim Phone: 0049 1796710242
Key data: 83 KW, 100 kVA
We currently offer: Number 58 Gesan generator set Type: DRP 100 Engine Perkins Generator LeRoy Somer Power: 83 KW / 100 KVA Hz 50 IP 23 Year of construction 2013 Hours: 15170 AVR regulation R438 Weight: 1906 kg We suspect that the engine has some damage. On the pictures you can also see that the water pump is missing and a sensor. You can find more machines on our website. If you have any further questions, please feel free to contact us. Adel e.K. Commercial Vehicles-Construction Machines Car Recycling Machine Dismantling Gottlieb-Daimler Str. 26 D-74831 Gundelsheim Phone: 0049 1796710242
S58 - used approx. 67 m³ / 67.000 L steel tank, standing. Technical details: Content: approx. 67 m³ / 67,000 litres Material: Steel tank single-walled Manufacturer: GEMS Metaalwerken Dimensions: approx. Ø 3.00 m × H Tank 9.90 m / H incl. railing 11.50 m Other: Used steel tank, professionally cleaned and in good condition. Vertical storage tank with flat bottom, dome on the tank body and on top of the roof, several inlets and outlets. Tank repainted from the inside in reddish brown (with a paint for the interior paint Brantho-Korrux "3 in 1", anti-rust paint, metal protection paint, maintenance paint, Brantho-Korrux 3in1 may be used according to the regulations of the Federal Health Office (XL) for the interior coating of food containers and food processing machines (tested by Lab. Dr. Kittel 01/1989). Only the pure tank is sold, without add-on parts such as pipes, fit ...
Distance between points: 1000 mm, Height of points: 180 mm, Max. diameter to be rectified: 355 mm, Max. piece weight between points: 300 Kg, Max. weight with plate: 125 Kg, Transverse travel of the carriage (X axis): 350 mm, X-axis speed: 0.01 / 6.000 mm/min, X-axis Resolution: 0.0001 mm, X-axis measurement system: Digital ruler, Longitudinal travel of the carriage (Z axis): 1.300 mm, Z-axis speed: 0.01 / 15,000 mm/min, Z-axis resolution: 0.0001 mm, Z-axis measurement system: Digital ruler, Working wheel dimensions (od x id x width): Ø500 x Ø203 x 80 mm, Main engine power: 7,5 Kw, Angle of rotation of the grinding head: -30º / +210º, Workhead rotation speed: 10 / 800 rpm, Workpiece holder head cone: MORSE 5, tailstock cone: MORSE 4, Ø of the tailstock shank: 60 mm, Course of the counterpoint reed: 40 mm, Control type (CNC/manual): CNC, CNC brand: FAGOR, CNC model: 8040-T, Dimensions ...
Height=2.1 m, Overall length= 1.45 m, Overall width= 3.25 m, Net weight= 300 kg,
Height=1.75 m, Overall length= 0.75 m, Overall width= 1.35 m, Net weight= 17 kg,
Open-end wrenches, ring wrenches as remaining stock -various sizes -Weight of tool: approx. 100 kg -Manufacturers: Gedore, Promat, Rahsol -Transport box: 800/450/H320 mm -Weight including packaging: 130 kg
Height=1.9 m, Overall length= 1.3 m, Overall width= 3.5 m, Net weight= 1110 kg,
Height=2.12 m, Overall length= 0.9 m, Overall width= 2.3 m, Net weight= 1110 kg,
Height=2.03 m, Overall length= 0.75 m, Overall width= 2.12 m, Net weight= 815 kg,
Height=2.12 m, Overall length= 0.9 m, Overall width= 2.4 m, Net weight= 1035 kg,
Height=2.51 m, Overall length= 1.3 m, Overall width= 3.25 m, Net weight= 1750 kg,
Height=2.2 m, Overall length= 1.15 m, Overall width= 2.05 m, Net weight= 1535 kg,
CONVEYOR BELTS, for waste material and more, sturdy steel structure, constructed in a workman like manner, Italian quality and components, can be lined in PVC, RUBBER or SHUTTER TYPE BARS, Can be prepared and fitted for METAL DETECTORS, and completed with OVERBELT METAL SEPARATORS, Size and characteristics bespoke to the project., Just fill your enquiry with the following data:, - Materials to be transported (photos appreciated), - Quantity in Tons/h, - required working width, - total length, - horizontal length, - diagonal length, - heigh of discharging point, - if prepared for metal detecto, - if fitted with metal detector (in this case, please add maximum contamination size), - if positioned in covered/uncovered place, We will send you a most targeted offer.
GEA Niro NS2006P piston homogeniser Serial: 6233 2005, Stainless, Max Press. (Mpa) 25, rated flow rate 150 dm3/h, 3Ph
maximum number of results exceeded
please refine your search
