134,910 used machines on RESALE, but how to find them? Machine Search
Specifications Maximum pressure: 9 tons Pressing force: 2.76 kg/cm² Bale size: 650x500x580 mm Power supply: 400V/4kW Year of construction: 1996 Productivity: approx. 3 bales/hr Machine is fully functional, after technical supervision.
Rotary indexing table with 12 stations Automatic ejector three pressing stages Pressure capacity 1,000 KN Stroke 12-120 mm Stroke rate 30-60 1/min Plunger adjustment 80 mm Total weight 9,500 kg
Technical data press: Manufacturer Paal (Kadant Paal) Type Konti 600 Year of construction 2008 Total operating hours: 23,020 hours Effective operating hours 1st pump: 10,719 hours, as of August 2026 Effective operating hours 2nd pump: 10718 hours, as of August 2026 Effective operating hours 3rd pump: 9,766 hours, as of August 2026 Number of bales pressed 183,075 bales, as of August 2026 Press force main press 158 t Specific pressing force 12.83 N/cm² Filling volume 3.45 m³ Theor. Throughput capacity approx. 1,266 m³/h Throughput under operating conditions approx. 805 m³/h Bale dimensions 1,100 x 1,100 mm, length variable Drive power 2 x 75 kW Total connected load, 135 kW Bonding 5-fold vertical, fully automatic throughput capacities with a Bulk density of 35 kg/cbm approx. 28.2 t//h Bulk density of 60 kg/cbm approx. 45.6 t/h Bulk density of 100 kg/cbm approx. ...
Technical data press: Manufacturer Paal (Kadant Paal) Type Konti 600 H Year of construction 2017 Total operating hours: 17,014 hours Effective operating hours 1st pump: 3,639 hours, as of August 2026 Effective operating hours 2nd pump: 3,518 hours, as of August 2026 Number of bales pressed 57,833 bales, as of August 2026 Press force main press 158 t Specific pressing force 12.83 N/cm² Filling volume 3.45 m³ Theor. Throughput capacity approx. 1,266 m³/h Throughput under operating conditions approx. 805 m³/h Bale dimensions 1,100 x 1,100 mm, length variable Drive power 2 x 75 kW Total connected load, 174 kW Current consumption, total 310 A Bonding 5-fold vertical, fully automatic throughput capacities with a Bulk density of 35 kg/cbm approx. 26 t//h Bulk density of 60 kg/cbm approx. 44 t/h Bulk density of 100 kg/cbm approx. 69 t/h Bale weights for a bale length ...
used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 18 S Year of construction: 2013 Serial No.: 116398 Specifications: Pressing force: 18t Engine: 4 kW Connection voltage: 400/50 V/Hz Cycle time: 22 s Pressing time: 12 s Insertion opening: W x H 107 x 62 cm Height from floor: 98 cm Bale ejected: W x H x D approx. 110 x 70 x 70-80 cm Bale height adjustable Bale weight: 120 – 180 kg depending on the material to be pressed Machine width: 152 cm Machine depth: 95 cm Machine height: 197 cm Weight: 850 kg (Subject to errors in the technical data)
used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 25 S Year of construction: 2012 Serial No.: 1113653 specifications: Pressing force: 25 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Bale size: 1,200 x 800 x max. 800 mm Bale weight: up to 250 - 320 kg Drive power: 5.5 kW Cycle time: approx. 24 sec. Pressing time: approx. 13 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)
used cabinet press Manafacture: HSM Type: 155.1 VL Year of construction: 1998 Machine no.: 6118.114. 01217M Serial no.: 6118.01217 specifications: Pressing force: 18 t Filling opening: 1,100 - 590 mm Filling space - 1100 - 700 x 1130 mm Bale size: 1,100 x 700 x 950 mm Bale weight: 110 - 200 kg Drive power: 4 kW Binding: 4-fold - vertical Output: 4 - 8 bales/hour Machine dimensions: 1,450 x 926 x 2,270 mm (W x D x H) Machine weight: 940 kg (Subject to errors in the technical data)
Technical data press: Manufacturer: Presto GmbH & Co. KG Type CC 36 M Year of construction 2010 Operating hours 3,641 hours Press force main press 36 t Specific pressing force 467 N/cm² Dimensions of the insertion tray 1,080 x 1100 mm (L x W) Cycle time 34 seconds Filling volume / pressing cycle 0.85 m³ Theor. Throughput capacity 90 m³/hour Throughput under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale dimensions 1100 x 750 mm (W x H), length variable Drive power 15 kW Tying 4-fold vertical, semi-automatic, with polyester plastic yarn throughput capacities with a Bulk density of 35 kg/cbm 1.8 t/hour Bulk density of 60 kg/cbm 2.5 t/hour Bulk density of 100 kg/cbm 3.1 t/hour Transport dimensions excluding press 4,200 x 1,640 x 2,200 mm (L x W x H) Machine weight press approx. 4 t Remarks: The press was checked for funct ...
Technical data press: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2010 Operating hours 3,817 hours, as of August 2026 Number of bales pressed 36,001 bales, as of August 2026 Press force main press 1000 kN Specific pressing force 120 N/cm² Press force cutting edges free kick 121 kN Dimensions of the insertion tray 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 to 2000 mm Drive power 2 x 45 kW, frequency-controlled Connected load 110 kW Current consumption, total 213 A Fuse 250 A slow blow Tying 5-fold horizontally, fully automatic throughput capacities with a Bulk density of 20 kg/cbm 12.86 t/hour Bulk density of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depending on t ...
used cabinet press Manafacture: HSM Type: VL 155.2 Year of construction: 08 / 2003 Machine No.: 6114.734. R Serial No.: 240141893 specifications: Pressing force: 16 t Filling opening: 1,100 - 590 mm Filling space - 1100 - 700 x 1130 mm Bale size: 1,100 x 700 x 950 mm Bale weight: 110 - 200 kg Drive power: 4 kW Binding: 4-fold - vertical Output: 4 - 8 bales/hour Machine dimensions: 1,450 x 926 x 2,270 mm (W x D x H) Machine weight: 940 kg (Subject to errors in the technical data)
Schuppenauslage mit integrierter Presse / Stream delivery with integrated pressing MBO ASP 66 - 2 ME Baujahr / Year 1999 Arbeitsbreite / Working width max. 660mm Geschwindigkeit / Speed min. 30m/min. - max. 160m/min. Stream delivery with integrated pressing rollers
Fully automatic baler Manufacturer: PAAL Type KONTI 325 G/S/k Operating hours: approx. 39,000 h Year of Make: 2012 Technical manufacturer data: Pressing force: 990 kN at 300 bar Specific pressing pressure: 120 N/cm² Drive power: 2 x 55 kW Pump capacity: 2 x 370 l/min. Total connected load: 150 kW / 260 A Volume output at idle: 800 m³/h Volume capacity at 35 kg/m³: 390 m³/h Performance at: 35 kg/m³ bulk density: approx. 13.50 t/h 60 kg/m³ bulk density: approx. 21.5 t/h 100 kg/m³ bulk density: approx. 33 t/h Filling opening: 1,020 x 1,750 mm Bale size: 750 x 1,100 mm Binding: 5-fold vertical + 3-fold horizontal Machine weight: approx. 28 t Bale weights: 525 to 800 kg including: - Free kicks - Wirbulator 15 kW - Automatic 3-fold horizontal tying with 40 kg wire unwinding device - W ...
Specifications Maximum pressure: 36 tons Pressing force: 46.75 tons/m² Duct cross-section: 700x1100 x reg mm Bale weight: 380 kg Power supply: 400 V/ 15 kW Year of construction: 2009-2010 Number of ties: 4 vertical Dimensions of the tailgate: 1030x1100 mm Weight: approx. 3.9 tonnes Bale tying: manual
Press for paper or plastic Pressing pressure 5 tons 400 V 16 A Length 80 cm Width 80 cm Height 2 m
SANGIACOMO T200 RCE 200T eccentric press was built in 2017 in Italy by OFFICINE S. GIACOMO srl. The machine is designed for cold metal forming. It enables operations such as precision blanking, stamping and deep drawing. Its wide range of machining capabilities, combined with a press force of 200 tonnes, makes it an excellent choice for the series production of components used in various industries. The SANGIACOMO T200 RCE features an intermediate wheel-pinion gear system. It provides high press force at a reduced nominal speed. As a result, the drive power can be used effectively when operating under high loads. The gears operate in an oil bath, ensuring proper lubrication of the drive components while reducing their wear. The machine’s frame is made of high-quality steel, while the shaft is made of forged alloy steel. The press also has an overload protection system that protec ...
SANGIACOMO T200 DM-DB 200T eccentric press was built in 2018 in Italy by OFFICINE S. GIACOMO srl. The machine is designed for cold metal forming. It enables operations such as precision blanking and stamping. Its wide range of machining capabilities, combined with a press force of 200 tonnes, make it an excellent choice for the series production of components used in various industries. The SANGIACOMO T200 DM-DB features a drive system based on a flywheel and an eccentric gear, cooperating with two connecting rods. This solution ensures uniform torque transmission, which translates into a smooth working cycle. All drive components are continuously lubricated by a central lubrication system to minimise their wear. The machine’s frame is made of high-quality steel, while the shaft is made of forged alloy steel. The open side wall enables the feeding of material strip. The press has ...
automatic baler Manafacture: PAAL Type: PACOMAT IS Year of construction: 1993 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Duct format: 700 x 700 mm Filling opening: 800 x 650 mm Drive power: 18.5 kW Throughput: 80 m³/h with additional manual feed hopper Wire passage seen in the direction of pressing on the left side
Hand screw press, used Balancier, used Typ/ type: PSHZ 25/I Presskraft / rated pressure: 25 t Hub/ stroke: 250 mm Tischgrösse/ table size: 400x 500 mm Ram: 200 x 500 mm Tischöffnung / hole in table: 140 mm Weight/ weight: 0,9t
Universal stamping machine Max impact power 50 KN Total stroke 80 mm Stroke sequence per hour 1500 Pneumatic Data
Inv. Num. : 6700 Type: 3000 kN Producer: Loire Created: 1992 GO 2008 Parameters: Control system: SIEMENS SIMATIC OP17 Compressive force: 3000 kN Table length: 2495 mm Table width: 1505 mm Maximum distance between the table and the ram (when the ram is low): 1200 mm Stroke: 800 mm Working speed: 64 mm/s
Inv. Num. : 6701 Type: 4000 kN Producer: Hydraulico Created: 1977 Parameters: Control system: SIEMENS SIMATIC OP Compressive force: 4000 kN Stroke: 800 mm Table height: 680 mm
pressure: 20 t throat: 185 mm stroke: 100 mm table surface area: 380 x 350 mm dayligth: 250 mm table height over floor: 840 mm total power requirement: 4 kW weight of the machine ca.: 1,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Working width: 4000 mm Working height: 2600 mm Number of cylinders: 6 St. Dimensions (L/W/H): 5300 x 1250 x 3330 mm S&S frame press type RP 2000, ----------------------------- C E - version Stable frame welded construction made of thick-walled special hollow profiles, Sliding carriage and pressure bar with 50 mm hole pattern. Continuous abutment on the left for width compression, lower abutment in two levels. Vertical press cylinder on special pressure bar with one-hand quick adjustment with weight compensation in the 50 mm hole pattern, height-adjustable, long Sliding carriages ensure the permanent absorption of high pressing forces. Fast, smooth width adjustment with ball-bearing carriage Central locking, fixation in 50 mm hole pattern. Upper horizontal press cylinder infinitely adjustable in height and with Equipped with counterbalance. Lower horizontal press cylinder with center hole ...
Stock Number: 3785 ECCENTRIC PRESS Manufacturer: PMB, Type: EPFT 100 Machine NO.: 004301, Year of manufacture: 2002 Specifications: Table size 780 x 590 mm Stroke length 8-120 mm Number of strokes per minute 55 Projection 300 mm Operating height 395 mm Total power 7.5 kW Pneumatic clutch. Gear ratio. Hydr. Overuse protection. Weight: 5500 kg
SPECIFICATIONS: 01 Hydraulic press ORMA LS/R-45/13 Dimensions: 4500 x 1300 mm 08 Piston Ø 70 mm 02 Piston with rack-and-pinion plunger Stroke: 200 mm 01 Loading roller conveyor 4500 x 2200 mm 01 Unloading roller conveyor 4500 x 1300 mm (with stop) ACCESSORIES: 01 Generator HF with 40 Kw 01 Double roll gluer 01 Manipulator ELEPHANT 200 kg Length: 4000 mm
SPECIFICATIONS: Suitable for processing backrests Number of spindles: 06 Speed: 10,000 rpm variable Max. machining depth: 50 mm Bending radius of the working table min - max: 300 - 900 Pneumatic workpiece clamping
Maplan Injection Moulding Machine Model: MTF400/80C 80 Ton Safety distance 162mm Run-on time 81ms Follow-up 5mm Pattern size 510mm x 410mm Touch screen control Year 2010
I sell a heavy briquetting press RUF RB400. Year of construction 11/2012 Engine power 22kW Productivity Number 400 pcs. Wood briquettes / hour Wood briquette RUF 150 x 60 x 40-110mm (Depends on material) Material moisture up to 15% Nominal pressure 14200 N/cm2 Oil cooler included. Dimensions: 3000 x 1800 x 2000 mm Combined weight 3000kg Equipment on the right - right entrance box. Condition after full remont/500Mtstd warranty as new. Available right away. With full documentation and CE.
used cabinet press Manafacture: HSM Type: V-Press 840 plus Year of construction: 2011 Machine No.: 6147.244. Serial No.: 340001635 Z specifications: Pressing force: 36 t / 356 kN Transport length approx. 1,780 m Transport width approx. 1,247 m Transport altitude approx. 2,985 m Insertion opening width approx. 1,195 m Insertion opening height approx. 0.65 m Drive power 4 kW Weight approx. 1.8 t Bale weight up to approx. 360 kg Binding: 4-fold vertical (Subject to errors in the technical data)
Leimo Plus Gluing press The new, innovative gluing press for clamping frames operable by one user for gluing drawers, carcasses, frames and surfaces, etc. Basic: 3 pressing units with angular gearbox 90° stop and lateral pressure device with angular gearbox Clamping dimensions: 1170 x 2300mm 3 pressing units with trapezoidal spindle 1 side pressure with 2 trapezoidal spindles 2700x700x1750mm G&FE-LEIMO-PLUS
Glue Gluing press Basic: 90° stop 3 pressing units with trapezoidal spindle Clamping dimensions: (H x W)1130 x 1900mm Quick adjustment up to 140mm Easy to use Self-clamping The gluing press from Bavaria Universally applicable Exact and accurate to the angle Can be operated by one user G&FE-LEIMO Options: 1 hold-down device G&FE-VP200-NL 1 press units with rack and pinion adjustment Driving device
RPW 3000 plus Frame press Clamping dimensions 1600x2900mm Frame 1600x2600mm Contact pressure of 1 t, self-locking, 140 mm travel Versatility - many applications (frame, body, surface gluing) Work facilitation - ergonomic posture Time savings due to user-friendly operation Frames are bolted and can therefore be dismantled Galvanized press units Basic: 3 pressing units with adjustable angular gears, 150mm adjustment range with 2 tons of compressive force! and 90° stop G&FE-RPW-3000PL OPTIONS AT EXTRA COST: Side pressure device with 2 angular gears Hold Chassis
LWB Steinl Injection Moulding / Vulcanizing Press Model: VCE-B Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 75 kW Hydraulic oil 40/45 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 1 Tool Kemp model TT-188 (year 2019) hot runner. Weight 12850 kgs
pressure: 110 t throat: 290 mm stroke: 20-124 mm no. of strokes: 60 / 90 Hub/min ram adjustment: 85 mm table surface area: ca. 920 x 590 mm ram surface: ca. 530 x 280 mm distance table to upper part of the press: ca. 450 mm hole in the table: ca. 180 x 300 mm mm table height: ca. 750 mm tool hole in ram: Ø 50 mm Number of working hours: 8214 h distance table to upper part of the press: mm weight of the machine ca.: 5,5 t dimensions: ca. 2000 x 2000 x 2600 mm overhauled by the manufacturer Helmerding in 2014 including conversion to new ones press safety control. Operating hours read since overhaul in 2014: 8214 Documentation of press safety control available electrical grease central lubrication Hydraulic clutch-brake combination Mechanical break plate in the ram two-hand operation foot control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
LWB Steinl Injection Moulding / Vulcanizing Presses Models available: VCEFE-B and VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Weight 13500 kgs
LWB Steinl Injection Moulding / Vulcanizing Press Model: VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Year 2013 Weight 13500 kgs
Used tablet press made by KORSCH Pharmapress 300 series. Model PH 343. Tablet diameter 6-13mm. 43 stations. 4 pieces available (2 x 1984, 1 x 1989, 1 x 1990)
Compressive force: 25 t Projection: 200 mm Table size: 450 x 600 mm Table adjustment: 240 mm Plunger adjustment: 70 mm Stroke adjustment: 4 - 80 mm Stroke rate: 150 rpm Drive motor: 380 V, 1.1 kW Space required: 1600 x 850 x 2000 mm Weight: approx. 1450 kg
New hydraulic pump QX61-250/63-100R88 for PAAL channel baler. Can be used in systems with a 75kW motor.
Brand new gear pump, with internal gearing for PAAL Konti, Pacomat channel baling press. Can be used in systems with a motor of at least 22 kW
Dual hydraulic pump for PAAL, 45kW Used 2-piece hydraulic pump for PAAL channel baling press. Can be used in systems with a 45 kW motor
Used Triple Hydraulic Pump QX51-125/53-063/52-063R91 for PAAL channel baler. Can be used in systems with a 45 kW or 55 kW motor. Manufacturer partnumber: QX51-125/53-063/52-063R91
Technical data for the grating: Manafacture: Gi-Ro Vreden Condition of the goods: new (unobstructed) Reason for return: Wrong order end customer The scope of delivery includes: 01x Press grate, new (unobstructed) Material color: hot-dip galvanized Total depth: 1,000 mm (support rod direction) Total width: 1,230 mm (crossbar direction) Support rod dimensions: 45/1.7 mm S355JR TS anti-slip: no QS anti-slip: no Edging: T-profile 45 mm Mesh size: 60 x 40 mm Weight: approx. 18.11 kg | Pcs. Internal designation: S Your contacts in our company: Mr. Andre Evering Mr.: Mario Klöver Lord: Falk German General information about the item: This item is offered for pickup only. Any further desired transport or shipment of this item is associated with additional costs, which can be requested separately from us depending on the place of delivery or scope of delivery.
Dimensions: 2,200 x 1,100 mm heating plate size Gold anodized heating plates 400 mm table opening height 4 hydraulic cylinders 50 tons of pressing pressure Stroke limitation Automatic opening Electrical opening and closing of the press table
Continuous press Manufacturer: Wemhöner Model: VSF Year of construction: 1972 Panel dimensions: 3600 x 2200mm Heating medium: Oil Feeding Destacking Total length approx.: 12.000mm
Technical data for the grating: Manafacture: Gi-Ro Vreden Condition of the goods: new (unobstructed) Reason for return: Wrong order end customer The scope of delivery includes: 01x Press grate, new (unobstructed) Material color: hot-dip galvanized Ctow7lyof8 Total depth: 1,000 mm (support rod direction) Total width: 980 mm (crossbar direction) Support rod diameter: 35/1.7 mm S355JR TS anti-slip: no QS anti-slip: no Edging: T-profile 35 mm Mesh size: 90 x 50 mm Weight: approx. 9.35 kg | Pcs. Internal designation: R
On sale is a complete line for the production of longitudinal and transverse plates. 1. Weinig Dimter high frequency press. 2. Grecon Ultra4 longitudinal line. 3. Line for width connection Obel. 4. Hobelrotoles. 5. Timesavers 1350 mm grinding machine with three units. 6. Planer Schenko (with lifting platform for parcels) + conveyor belt + charger. 7. SLH cold width press. 8. Thermal tunnel for individual packaging of plates. 9. Glue applicator Inles. 10. Glue applicator for slats. 11. Obles line for longitudinal connection of slats.
maximum number of results exceeded
please refine your search
