for used for sale

continuous grilling line grilling surface (w x l) : 600 x 7.500 mm bottom contact grilling + hot air (with flip-over) grilling time : 1 minute to 60 minutes belt width ± 600 mm electrically heated power : 2x200 A, 2x140kW, 3 x 400V, 50 Hz belt washing system adjustable speed overall dimensions (l x w x h) : ± 10.315 x 1.230 x 2.338 mm weight : ± 4.500kg

used 2 row Fortuna head machine mobile maximum hourly output 2400 pieces per srtück.Compact machine robust construction easy cleaning.Payment and delivery on request. Weight range 35-80 grams round buns 2-row Painted on rolls checked and cleaned Dimensions: Height: 170 cm Width: 100 cm Depth: 70 cm

1 x 'Forward Machinery Industrial Corp'. (Taiwan) 4 roll inverted L calender line, Year of manufacture: 2007, Roll dimensions: 34in (860mm) dia x 157in (4000mm) wide, Peripherally drilled (oil heating), Roller bearings, Motorised nip gap adjustment, Roll bending rolls 2 and 4, Cross axis roll 3, Independent drive to each roll:- Roll 1: 110kW, Roll 2: 150kW, Roll 3: 150kW, Roll 4: 110kW. Finished product width 3600mm. Pick off rollers, Matt finish embossing station, Edge trimming, 19 x cooling drums 355mm dia x 4000mm wide, Dual station surface winder. The line is already dismantled and ready for immediate shipment. There is also upstream equipment available by separate negotiation (high speed mixers, 2 x 100L Banbury, strainer, two roll mills etc).

Three flywheels Diameter mm: 900

Drying oven, curring oven chanel, chamber with fans Working temperature: 130 C° Max temperature: 200 C° 2 chamber Chamber 30 m3 Open size : 90x120 cm Heating capacity 110 kW 72 heating elements

Bread machine Fortuna Premium K with Magnus head machine -6 in a row -Stainless steel -with Siemens Touch control -Cutting rolls and Kaiser rolls -Built in 2010

P181 - used approx. 40 m³ / 40,000 litres PE-HD-tank, plastic tank, flat bottom tank, double-walled with an outer hull. specifications: capacity: approx. 40 m³ / 40,000 litres material: PE-HD tank, plastic tank manufacturer: Formoplast Kunststofftechnik GmbH measurements: Ø approx. 3,49 m outside / Ø approx. 3,00 inside x height tank approx. 5,70 m / total height approx. 6,50 m mark of conformity: PA-VI 321.103 specific weight: 1,13 kg/L media: former chemical tank for formalin DIBT and media list available, suitable for AHL and ASL PE-HD tank, professionally cleaned and in good condition. Double-walled, i.e. with an outer hull, non-translucid, various connections such as ventilation, inlet, suction pipe, etc., lid on top of the roof. According to the media list suitable for many different chemicals e.g. iron chloride, hydrochloric acid, acetic acid, caustic soda, sul ...

Painting drying plant Giardina Forno Statico MOS 3D Masch. No. 050354 Built in 2006 User manual available This plant is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Form-on smartPROP 20 sF2 - 2,00 - 3,50m, new a 33,95€ net -low weight -long service life -safe working Your benefits: Effortless and fast work due to the low dead weight Preservation of the value of the support over many years thanks to high-quality production and galvanizing Safe working thanks to crushing and Failover Purchase and sale of scaffolding/formwork systems and construction machinery; Formwork restoration at fair conditions. Company SFS Meisterbetrieb Andreas Becker e. Kfm. Phone 07305/9562350, Fax. 07305/9562352 mobile: 0049 176 70044689 Mr. Becker Office/ warehouse address: Birkenstrasse 15 D-89185 Humlangen-Hüttisheim e-mail: sfsystemst-online.de Register court Ulm: HRA722943 VAT ID NO: DE279047055

Technical data: - Drilling capacity in steel ST 60 40 mm - Drilling capacity in steel ST 60 45 mm - Drilling spindle holder MK 4 - Drilling spindle stroke 200 mm - Extension 385 mm - Table with 2 T-slots with hand crank adjustable height - Table size 550 x 480 mm - min. / max distance table / drill spindle 120 / 650 mm - Column diameter 200 mm - Feed electromagnetic 0.1 - 0.2 - 0.3 - 0.4 mm/U. with overload protection - Drilling spindle speeds infinitely variable in 3 stages 60 - 1900 rpm. - Drive 400 V / 3 kW - Space requirement approx. W 700 x H 2120 x D 1100 mm - Weight approx. 700 kg - with: - Thread cutting device - Coolant device - digital speed display

Hydraulic

continuous grilling line all stainless steel bottom contact grilling + hot air suitable for steam injection belt width 1,100 mm net length 11,000 mm underplate max. 260°C air temperature max. 280°C dimensions (l x w x h) : x 13,500 x 1,700 x 2,400 mm independent platen - air temperature and steam control adjustable speed PLC control Siemens frequency (new hard- and software, frequency inverters) With new Teflon belt suitable for thermic oil heating (600 kW) with belt wash system

- Machine weight: 7 kg - Space requirement (W x D x H): 0.3 x 0.3 x 0.2 m Details Separate control unit for chuck clamping

Circular automatic saw make FORTE type FKA 45Built in 1970Saw blade dimensions: 225 x 32 x 2 mmCutting performance in non-ferrous metal: 60 mmCutting performance in steel: 45 mmSection length automatically up to: 200 mmCutting speeds: 35 - 900 m / minFeed rate hydraulic: 300/600 mm / sDrive power: 4/5 kWDimensions L x W x H: 2700 x 700 x 1250 mmWeight approx: 1033 kgWith- Bar magazine for steel and non-ferrous metalsExclusively non-ferrous metal has been produced on the machine!used, from an operating resolution, despite the year of constructionin very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Cutting area round: 250 mm Cutting area rectangular: 250 mm Saw band dimensions: 3660 x 25 x 0.9 mm Band speed: 20 - 70 m/min Saw drive: 1 kW Space requirement: 1900 x 1450 x 1250 mm Weight: approx. 850 kg

Pasta and automatic machine Fortuna head machine KM 4 used Fortuna head machine KM4, 4-row with flour. Easy cleaning of the parts because easily accessible. Capacity up to max. 4800 pieces/hr weight range of the head machine between 35-80 grams. Divide and act of dough as if by hand. Payment and shipping on request. 4-row Weight range 35-80 grams Hourly capacity max. 4800 pcs. Flour spreader mobile on wheels

7” color LCD touch screen control panel High capacity program memory Picture recipe feature Multi-language option Multi-step cooking feature Ability to work with Ng or Electric Equal heat distribution with bidirectional fan Adjustable cooking temperature between 0-300 °C Adjustable cooking time Manual or automatic humidification feature Door system with sensors Tempered glass with silicone gasket Openable inner glass for easy cleaning Stainless steel body Capacity: 20GN 1/1 Weight: 239 kg Electric power: 26kW Power inlet: 380V 3N PE Dimensions of the machine in mm: Width: 960 Length: 1000 Height: 1820 Delivery time: after advanced payment, 10 to 30 working days

Manufacturer: fortron Company Helmut Schäfer GmbH, 7442 Neuffen Model: F 5000 ? year: approx. 1995 Equipment: instruction manual Manual "Installation and soft goods" Manual "How to ... " Manual "Inside ... " Various floppy disks, stick and DVD 18 embroidery hoop 6 different sizes in 3 copies 3 attachments for caps Completely 1 thread Take-up machine and various Small parts that I cannot classify. Condition / defects: the condition is very good and it became a few years ago General overhaul Made. Availability: Immediately after consultation Price: on request

Description Universal band saw of the Brand Forte suitable for tooling, fixture construction, training as well as mould making Cutting diameter: 400mm Sheet: 4870mm Technical data Cutting diameter 400mm Sheet 4870mm Speed 20-30-40-60 m/min Coolant Yes Connection 50 Hz 3x 380V Spindle motor 2.2KW

Dough part and control machine bread press Fortuna Automat A3-30 with power switch, used dough part and control machine Fortuna Automat Model A3-30 with electric head. The machine is sold including 3 plastic impact plates, optionally completely overhauled and repainted. We will be happy to send you further pictures and information by email on request. -Bread press -with 3 plastic actuator plates -head tilting backwards electric -30 division -Weight range dough pieces 32-80 grams -Dough insert per actuator 960-2400 grams -380V / 50Hz -Bread press dough kliev machine -Weight of the machine approx. 540 kg

Ford generator set 35 kVA only 20 operating hours - - - - - Engine: -Ford - 3 cylinders -Diesel -Water-cooled - 1500 rpm - - - - - Generator: - 35 kVA - 230 / 400 volts - 50 Hertz - AVR ESC - - - - - Starter Unit: - Ignition lock for starting - Engine temperature display - Oil pressure indicator - Generator monitoring: volts, amps, hertz - Operating hours counter: 19 operating hours - - - - - Condition: - The generator set is an emergency system - It has only run 20 hours of operation - A test run with load reduction was made - The engine starts and runs well - The generator generates 400 volts and 50 hertz - A new AVR controller has been installed - - - - - Scope of delivery: - Ford generator set 35 kVA - with starter unit -Tank -Exhaust - - - - - Transport: - A Germany-wide transport is possible for an extra charge - In ord ...

gebr. Roll press Fortuna fully automatic size 3, overhauled, for angular rolls, with 3 work plates, newly painted, 30-piece, weight of the dough pieces: 32 – 70 g, dough insert approx. 960 – 2100 g, 147 cm high, 69 cm wide, 80 cm deep, weight: 540 kg

Formwork/Beam H20 Form-on smartBEAM 20 P new from 6,50 EUR/lm Form-on smartBEAMS 20P new, bridge made of phenolic resin glued hardboard, available in all lengths: Subject to sale Your benefits: - reliably high load-bearing capacity over the entire length of the beam due to the homogeneous web material - Secured component load-bearing capacity through mechanical strength grading and load test for 100% of the belts - consistent product properties thanks to high dimensional stability - multiple savings compared to squared timber due to higher load-bearing capacity with lower weight Carrier produced according to DIN EN and with German technical approval. The images listed are sample images All prices excl. VAT and transport Subject to sale For questions Mr. Becker under 0176700 44689 Purchase and sale of scaffolding/formwork systems and construction ma ...

Machine Mechanics & electrics completely overhauled & repainted by an expert 6 months warranty Properties: + Stationary machine, very robust & stable construction + Machine is set in motion by switch-on lever, one-hand operation + with effective cut-off + Cleaning position to the rear with hand crank + even division of the dough, excellent rounding of the dough pieces + Partial knife / cutter head has been overhauled / recoated + Machine was completely disassembled, mechanically & electrically overhauled, repainted + Transmission parts run constantly in an oil bath + complete overhaul in our workshop, according to German quality standards + only high-quality original parts are installed + Machine was finally tested with dough by master baker Standard equipment: + incl. 3x knitting plate, new Special equipment, available at extra cost: + Chassis for Fortuna Automat ...

Roll press / dough dividing and warp knitting machine / Klievmaschine Machine Mechanics completely overhauled & repainted by the expert New installation of the entire electrical system, according to the latest standards 6 months warranty Properties: + Stationary machine, very robust & stable construction + Machine is set in motion by switch-on lever, one-hand operation + Cleaning position electric, to the rear, with switch + even division of the dough, excellent rounding of the dough pieces + equipped with active cut-off, for square dough pieces + Partial knife / cutter head has been overhauled / recoated + completely disassembled, mechanically overhauled, repainted + New installation of the entire electrical system, according to the latest standards + Transmission parts run constantly in an oil bath + complete overhaul in Babenhausen, according to German quality stand ...

Moretti Forni convection oven Model: F80E Serial: 1321225 2006, stainless, variable temp and timer controls, with ability to steam, on mobile frame, 18.5kw, 3Ph

saw blade diameter: 225 mm cutting diameter: max. 60 mm feed: max. 600 mm total power requirement: 5 kW weight of the machine ca.: 1,03 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 6000 mm y-travel: 3500 mm z-travel: 1900 mm surface area: 6000x2500 mm control: Siemens type: 840D Tool changer: 40 chip conveyor: Richter b-axis: +/- 110 ° c-axis: 360° 0 turning speeds: 30.000 U/min total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

diameter: 315 mm weight of the machine ca.: 100 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

diameter: 250 - 500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

continuous grilling line suitable for frying, cooking or browning electric heating 400 kW 510A, 3 x 400V, 50Hz with bottom and top band : bottom and top contact frying Overall dimensions (L x W x H) : ± 7,700 x 2,300 x 2,400 mm Cooking time: from 10 sec. to 5 min. Useful length 6,000 mm Track width 1,060 mm max 260 degrees product height 250 mm Air: 6 bar - 100 l/min Water: 65 degrees - 2 bar - 30 l /min variable frying height infinitely variable speed pneumatically controlled tape Siemens PLC control with belt washing system

Diesel forklift Machine Brand: DOOSAN Designation: D90S-5 Year of production: 2012 Counter Reading (mtg): 7970 Empty weight (Kg): 12197 Lifting capacity (kg): 9000 Height. lift. (mm): 3100 Lateral fork travel Mast type: STD UDT review until March 2022 Fuel type: diesel After a large technical inspection for over PLN 30,000 (we have invoices for everything) - new tires - new fore fore fore - regeneration of actuators, - gearbox: discs + sealants - brakes: discs and bearings - all oils, liquids and filters Technical condition: used, very good

continuous grilling line completely stainless steel adjustable product height Useful length 1,800 mm Track width 600 mm with bottom and top band: bottom and top contact frying independent temperature control at the top and bottom electrically heated ± 90 kW with belt washing system at the top and bottom Adjustable temperature range per heating plate (6 pieces) Capacity up to 250 kg / hour depending on the product infinitely variable speed Dimensions (L x W x H): ± 3,000 x 1,650 x 2,400 mm

Fortuna dough dividing and working machine Type: A3 Completely overhauled repainted Division of 30 Weight range dough pieces 32-80 grams Dough insert per saucer 960-2400 grams with incubation electric head The robust design and duration oil lubricating of the transmission parts ensures a long service life Easy cleaning of the knife head 380V / 50Hz Weight of the machine approx. 640 kg Machine stands on a specially made wheelchair Dimensions: Height: 150 cm Width: 60 cm Depth: 70 cm The machine was completely dismantled and completely overhauled from the ground up. Then completely repainted.

Fortuna Viereck Ciabatta - Bread roll system Type: TM 4-row with flour spreader with sprinkler with seed storage with turntable with Spüher Hourly output approx. 3800 pieces Stainless steel version on rolls 380V 50Hz

Fortuna + Lippelt Bread Roll System Compact Fortuna Primus K4 Head Machine 4- Rows Weight range: 35 - 80 grams Volumetric lobe diameter: 64 with hardening plate Hourly output max.  5000 / piece Front + Rear + Roller Flourer 2x working speed (slow + fast) Siemens Simatic Touch Panel Control Rev. 2010 Machine volume max. 70dB Weight head machine: 600kg Lippelt fermentation cabinet Type: G 8000 L/R Year of construction 2014 Operable from 4 to 6 rows (depending on the head machine) Number of hours per head machine from 5000 - 8000 pieces with punching station for round and long rolled dough pieces  4x punching with cutting device punch Cutting strength adjustable with stamp station with direct setting on 58x78cm & 58x98cm sheets with settling tape Special fermentation carriers without mould accumulation Siemens Touch Panel Color Screen incl. accessories on  ...

Fortuna dough dividing and working machine Type: A3 Division of 30 Weight range dough pieces 32-80 grams Dough insert per saucer 960-2400 grams including 3 plastic effect plates The robust design and duration oil lubricating of the transmission parts ensures a long service life Easy cleaning of the knife head Knife head electrically tiltable backwards for cleaning 380V / 50Hz Weight of the machine approx. 540 kg Trade-in and delivery on request Option Basic overhaul of the machine Dimensions: Height: 150 cm Width: 60 cm Depth: 40 cm

Capacity (x): 0 Process Application: 0   Other Info: 0 Technical data Diameter: 350 mm Machine´s weight about: 120 kg

Capacity round maximum diameter: 1780 mm Angle degrees maximum: 0 Capacity square: 0 mm Workpiece height: 0 mm Workpiece width: 0 mm Capacity rectangle: 0 mm SPECIFICATIONS Bandsaw / Circelblade / Automat  bandsaw   Angle L / R Degrees  90 gr Cutting capacity 90 ˚ Ø  1780 mm Cuttting capacity 90 ˚ Flatt   1780 x 1780 mm Max. cutting length 450 mm

Two-jaw chuck, 2 jaw chucks, vice, face plate -exciting: centric -Chuck size: Ø 200 mm -Weight: 19 kg

- 2 saeulen-execution - Working area Durchm. u. Square 420 mm - Material feed length 3 - 600 mm single feed , - Cutting speed infinitely variable 12-100 m/min. - Heegeband dimensions 6050 X 40 X 1.3 mm - Drive 9.5 kW - Dimensions L/BH 2050 x 2725 x 2080/ 2530 mm - Weight: 4000 kg - Machine dimensions: L x W 1500 x1900 mm - Weight: approx. 1700 kg

Workbench, work table, assembly bench -Width: 1250 mm -Depth: 700 mm -Height: 860 mm -Drawer: 1 -Weight: 75 kg

Face plate, face plate chuck, four-jaw chuck -without: screw-on jaws -Manufacturer: Forkardt -Chuck size: Ø 610 mm -Taper holder short taper: 8 (139 mm) -Weight: 121 kg

Dough dividing and warping machine Fortuna Bread roll press size 3 Semi-automatic 30-piece Part header NEW revised Stainless steel knives NEW Dough insert up to 2550g, depending on TA Piece from 35 to 70g Round/85g Square Capacity max. 7000 pieces/h with 3 new knitting plates E-system new DGUV V3 tested Connection 400V, 1 kW, 16A-CEE plug Dimensions: 580 x 580 x 1350 mm, WxDxH Used machine overhauled with 6 months warranty

Cylindrical Grinder Model: FM41G-1600CNL45 New in 1988 Control: FM4 CNC Maker: Fortuna (Germany) Ser. No. 15674 Maximum grinding diameter: 275mm Maximum grinding length: 1600mm Additional measurement device

Bread roll press Fortuna A3-30 semi-automatic Dough part and warp knitting machine Fortuna semi automat A3-30 - 30s division - with 3 knitting plates - manual head to the side - Weight range dough pieces 32-80 grams - Dough insert per serving plate 960-2400 grams

Fortuna Automat A4-30 dough dividing and warping machine A used dough part and warp knitting machine Fortuna Automat A3-30 with knitting switch is currently for sale and immediately available in our warehouse in Bielefeld. Dough part and warp knitting machine Fortuna Automat A3-30 with active cabling switch - 30s division - with 3 knitting plates - with active cabling switch - electric head - Weight range dough pieces 40-110 grams - Dough insert per serving plate 1200-3600 grams - Weight of the machine approx. 540 kg

60″ x .135″ x 20,000Lb Cincinnati – Forte Loop Slitting Line Material Width: 12″ – 60″ , Thickness: .010″ – .135″, Weight: 20,000Lb, Coil ID: 16″ – 24″, Coil OD: 72″, Speed: 600 fpm, Direction: Left to Right. Entry Turnstile, Entry L-Type Coil Car, Mandrel Uncoiler with Hold-Down Roll, Powered Peeler, Driven Pinch Rolls, PVC Applicator, Entry Shear, Two Slitting Heads, Injection Design, 5″ & 7″ Arbor Diameter, 75HP DC Motor, Two (2) Hydraulic Scrap Winders, Pit Cross Over Table, Drag Board & Rotary Tension Stand, Recoiler with Over-Arm Separator & Push-Off, 150HP DC Motor, Exit L-Type Coil Car & Turnstile. Electrics, Hydraulics, Controls, Tooling, Spare Parts

Type: S-30 Sealing length: 305 mm Vacuum pump: 10 m3/h Machine cycle: 20 - 40 sec. Voltage: 380 V, 50 Hz Electric power: 0.6 kW Machine dimension in cm: Width: 40 Lenght: 32 Height: 36 Delivery time: after advanced payment, 1 working day