129,020 used machines on RESALE, but how to find them? Machine Search
Punching tool with Linar built-in punching brackets ABS-SCHWABE type 100/16011 piece Punching bracket, punching unit for press brakeYear of construction approx. 1990Throat: 160 mmPunching capacity: 0.3 to 5 mm Material thicknessHole diameter: 2 to 7 mmInstallation height: 203 mm (only the punching bracket individually with punching tool)Installed is a round hole tool ø 5 mmPunching bracket distance: 195 mm- the tool unit was mounted on a hydraulic press brakeDimensions punching bracket base plate L x W x H: 2500 x 345 x 37.5 mmDimensions of punching bracket printing plate L x W x H: 2500 x 173 x
Straightening and welding plate: cast steel-grey cast iron, heavily ribbedheavyheavy: straightening plateLength 1600 mmwidth: 1005 mmThickness: 280 mmPlate thickness approx. 85 mm, continuous- Center hole 245 mm, 400/800 mm - Tapped holes M 20, approx. 55 mm deep- Through-holes 27 mmWeight: approx. 2.5 to.Good conditionFormer press table - presumably worked on both sides; used
Stacker trucks, pedestrian stackers, hand pedestrian stackers LOGITRANS type LF 1001 / 1600Tool liftersSeries No: 051E04006100 Year of construction: 2005Load capacity: 1000 kg Lifting height: 1600 mmFork length: 600 mmPlatform size: 800 x 650 mmTotal length: 1200 mmTotal width: 800 mmOverall height: 1930 mm- Lifting via mechanical lifting hydraulics, pumping movement with the steering drawbar- 2 lifting speeds approx. 36 strokes up to lifting height 1600 mm or approx. 10 strokes for 10 cm lifting height.- Driving by pushing by hand- Fork stroke in the Single mast with free liftdead weight
TIG and Electric Welding Machine / Inverter ESAB Type LTN 160WIG Welding Machine for TIG and ElectrodeFabr. No. 405-423-0479 Year of construction approx. 2010Power TIG 160 Amp. = 35% ED 110 Amp. = 60% ED 80 Amp. = 100% EDL power electrode 140 Amp. = 35% ED 110 Amp. = 60% ED 80 Amp. = 100% EDNetz connection 230 Volt, 50 Hz, Schuko plug- stepless power adjustment- 2 stroke and 4 stroke operation- Operating mode rod electrode- 12 meter TIG hose package with hand torch- only DC = DC- HF ignition-
LPG forklift, gas forklift STILL type RX 70-16TSeries No. 517314G00021 Year of construction 2016Nominal load capacity 1600 kgLifting height 4920 mmFork length 1000 mmCarriage width 980 mmOverall height 2160 mmTotal width 1100 mmTotal length without forks 2200 mmNet weight 3040 kg- Triplex mast with full free lift 1550 mm- Hydraulic sideshift- LPG electric drive- 4-cylinder Volkswagen LPG engine with 30 kW- Hydraulic auxiliary steering- Front working lights- Reversing Warning light (blue)
Straightening and welded plate cast steel-grey cast iron heavily ribbedheavyheavy straightening plateLength 1600 mmWidth 1000 mmThickness 210 mmPanel thickness approx. 32 mm throughoutTable height / working height 565 mm- very stable steel table substructure (self-made)- plate with substructure can be moved by pallet truckWeight 740 kggood condition; used
A complete cutting line for sheet metal processing is available. 1) Decoiler Schleicher H-B4-1250, year of manufacture: 1983, power: 11kW, max. load capacity: 12500kg, strip thickness range: 0.5mm-1.25mm, max. strip width: 1100mm. 2) Straightening machine Schleicher RM 8-53/160, year of construction: 1980, power: 7.68kW, strip thickness range: 0.5mm-1.25mm, strip width range: 300mm-1000mm. 3) Trimming shears. 4) HSK HSKW/SF shears, year of manufacture: 1993, max. strip thickness: 1.5mm, max. material width: 1280mm. 5) Stacking line Schleicher, year of manufacture: 1980, max. load capacity: 1000kg, strip width range: 300mm-1000mm, strip thickness range: 0.5mm-1.25mm, feed length range: 200mm-1250mm, power: 1.5kW. On-site inspection is possible.
Inv. Num. : 8549 Type: Cutex-160B MC Producer: Hwacheon Created: 2017 Parameters: Control system: FANUC 0i-SERIES (TF) Max. turning diameter: 260 mm Maximum turning diameter over bed: 550 mm Maximum spindle speed: 4500 1/min Lathe chuck diameter: 200 mm Weight: 3280 kg
Manufacturer:DMG Model: DMC 160 UP Year of Manufacture: 2003 Machine with 240-tool magazine Pallet changer with 5 positions Work spindle: SK 50 Control system: Siemens Sinumerik 840D 2429093 Power-on hours: current counter: 3259 hours -> Mechanical counter with 5 digits, skipped once, thus 103259 hours. Program operating hours: current counter: 39391 hours. Condition: functional, used machine, commensurate with age Accessories: Includes tool holders, some with tools (upon request) Find more here - / Contact us at -
PRIMULTINI log bandsaw line, type SIB-1600-CFK-IFB, Consisting of:, PRIMULTINI hydraulic log carriage, type CFK, - undependable headblock movement, - 5 pc hydraulic headblocks, - Opening headblocks horizontal 1000 mm, - Each headblocks with brushless motor for movement, - Distance between headblocks 1400 – 1750 – 2000 – 3350 mm, - Length log carriage ca. 10,5 meters, - Each headridge with double hydraulic centering pad, - Integrated log turners, PRIMULTINI hydraulic driven rope feeding, type IFB, With separate motor, with 55 kW power, with rails, total length 30 meters, SWECAN chipper canter machine, Motor power 75 kW, Control cabin with MUDATA touch screen controller, RIMULTINI band saw machine, type SIB 1600, - Diameter flywheels 1600 mm, - Width of flywheels 245 mm, - Maximum sawblade 260 mm, - Saw blade protection, - Blade guide with hydraulic pressure, - Electric adjustment bl ...
1 of used gearbox, Lenze type 52.162.06.000, ratio I=15,53. Overhauled with new bearings, seals, oil, silent block and spider.
Key data: 160 t, 4000 mm
160 ton x 40000mm Multi Axis CNC
used spiral mixer Eberhardt 160, overhauled, for 160 kg dough, 2 watches, stainless steel kettle, stainless steel spiral, new wiring, repainted, new bearings, new V-belts
Offer 25247 Specifications: - Max. pressing force 50 t - Max. ram stroke approx. 260 mm - Lifting speed fast approx. 1540 mm/min - Lifting speed slowly approx. 210 mm/min - Stand width approx. 770 mm - Stand depth approx. 195 mm - Min. / max. installation height approx. 200 / 1100 mm - Table height-adjustable with 5 plug-in bolt grids each approx. 180 mm - Support plate approx. 450 x 450 mm - Height adjustment of the table with hand crank cable - Drive 400 V / 1.5 kW - Space requirement approx. W 1750 x H 2100 x D 850 mm - Weight approx. 600 kg
Inv. Num. : 8584 Type: PEDA 160 Producer: IWK Created: 1972 Parameters: Compressive force: 160 t
Inv. Num. : 8585 Type: KPRW 160 Producer: Kieserling Created: 1972 Parameters: Compressive force: 160 t
x-travel: 4500 mm y-travel: 3800 mm z-travel: 1850 mm column daylight: Z = 1900 mm column daylight: Y = 5330 mm table surface area: 4500 x 4600 mm table load: 50 t milling head speed: 40 - 2000 U/min feeds x/y/z -stepless: 6 - 4000 mm/min rapid travel x/y/z: 6000 mm/min milling drive: 40 kW milling spindle diameter in the forward pos.: 160 mm tool taper: Steilk. 60 milling spindle quill diameter: 260 Control: Siemens 840D total power requirement: ca. 60 kW weight of the machine ca.: 115 t dimensions of the machine ca.: 10,0 x 5,0 x 5,7 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Feed rate: 250mm/min, speed: 2800rpm, tool diameter: 200mm, weight: approx. 850kg. An on-site inspection is possible.
CONTROLS PLC SIEMENS S7 PRESS DESIGN drive system: knuckle-joint frame design: H-frame, monoblock openings in uprights: yes number of suspensions: 2 feedstock transport direction: left to right PRESS FORCES total force (nominal): 315 to nominal work capacity: 38 kNm PRESS TABLE table surface (left-right): 2000 mm table surface (front-back): 1200 mm thickness of bolster plate: 200 mm SLIDE slide force: 315 to table surface (left-right): 1995 mm table surface (front-back): 1100 mm stroke: 160 mm stroke rate (max.): 80 /min SLIDE (MECHAN. PRESS) slide adjustment: 140 mm stroke rate (min.): 20 /min stroke rate (max.): 80 /min main drive power: 90 kW TOO ...
Inv. Num. : 8609 Type: 1600 KOMBI Producer: NESSAP Generated: Parameters: Control system: NESSAP Software: WRYKRYS Work table length: 3000 mm Work table width: 1500 mm Minimum sheet thickness: 0.5 mm Maximum sheet thickness when cutting: 100 mm Plasma Source: Cebora 160A Cutting speed: 12 m/min
Diesel Generators 1600 kWe / 50Hz with CAT 3516B engines and local control panel We have multiple identical CAT 3516B skid-mounted diesel generating sets available, all manufactured in 2018 and installed in the same HFO power plant, complete with full HFO plant auxiliaries. Each engine is coupled to a 2000 kVA / 415 V / 50 Hz brushless synchronous alternator via a flexible coupling, both mounted on a rigid base frame. These units are optimized for low emissions, high efficiency, and continuous base load operation. The generators have been serviced exclusively by the local CAT dealer and have only 1,500–2,000 operating hours. The standard scope of supply includes: • Engine control panel (EMCP 4) • 24V electric starting system • Radiator cooler Balance of Plant (BOP) equipment is available for customers requiring multiple units. Technical data Engine type CAT ...
Engel Injection Machine Type ES 1500T/160 V – ELAST Stroke slide plate 300mm Stroke central ejector for slide plate 100mm Force central ejector for slide plate 30kN Stroke lateral mechanical ejector 250mm Stroke lateral hydraulic ejector 250mm Force lateral hydraulic ejector 80kN Stroke central ejector 120mm Force central ejector 20kN Pump drive power 15kW Oil filling 1 225 Operating pressure of hydraulic system 250bar Capacity temperature control unit 2x3 kW Total connected load 48kW Dims: 2675mm long x 1350mm wide x 3310mm high Weight: 6900 With instruction manual
An almost like-new injection moulding machine Arburg is available. Clamping force: 1600kN, tie bar distance: 520mm, clamping stroke: 364mm, ejector stroke: 150mm, ejector force: 40kN, injection unit: 400, injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 6000mm/1800mm/2200mm, weight: approx. 6000kg, control: Selogica, operating hours: approx. 67h. Includes enclosure with clean air supply FilterFanUnit and removal robot. Documentation available. An on-site inspection is possible.
x-travel: 900 mm y-travel: 300 mm z-travel: 1000 mm control: Siemens Sinumerik 840D max. workpiece diameter: 1600 mm max. module: 20 mm tip circle diameter: 350 mm Milling arbour diameter: 375 mm Total closing value: 80 kVa weight of the machine ca.: 33,5 t dimensions of the machine ca.: 10,530 x 6,375 x 4,680 m Feed rate: - X-axis 1 to 3000 mm/min - Y-axis 1 to 3000 mm/min - Z-axis 1 to 4000 mm/min Spindle speeds in rpm: - Tool 26 to 265 - Workpiece table 0 to 8 Equipment/accessories: - M 2 motor milling head - Milling mandrels - Oil cooler - Technical documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Transnorm belt curve conveyor left 30°-1270-1100-IR900 RA2303 Technical data: Frame width (NB): 1270 mm Frame width with Bearing cover: 1390 mm Frame width with Bearing cover and gearbox: 1480 mm belt width (GuB): 1100 mm height (BH): 250 mm height motor below: 300 mm height including motor (MH): 550 mm Inner radius (IR): 900 mm Conveying angle: 30° degrees middler conveying speed (v m/s): 1,0 m/s Drive: SEW motor motor with frequency converter Electrical data: 50Hz V380-500, kW 1,5 / S1 Belt: KT 96 new Year of construction: 2021 Height Sideguides: 194 mm Optionally available: Supports Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2021 condition: new Nominal / inner radius in mm: 900 Nominal / outside width in mm: 1270 Belt width in mm: 1100 angle: 30° Driven: YES Running direction: LINKS Engine type: SEW Eurodrive K ...
thickness of jaw: 160 mm max. clamping width: 310 mm ca. tension force: ca. 5 to high of jaw: 50 mm Dimensions (L/W/H): 750 x 160 x 200 mm weight: ca. 60 kg High pressure vice with turning plate. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Gems 164870 LS-7 Type 9 Level Switch, NO/NC, 300PSI, 1/2"NPT, 120-240VAC
turning length: 1000 mm turning diameter: 350 mm turning dia. in gap: 450 mm spindle bore: 40,0 mm turning speeds: 70 - 2000 U/min bed width: 180 mm spindle taper: 55029 D 1-4 taper in tailstock: 3 MK quill travel: 110 mm total power requirement: 1,5 kW weight of the machine ca.: 529 kg. range L-W-H: 1730x700x1340 mm Scope of delivery: - 3-axis digital display i200 with LCD display - 3-jaw chuck DK11-160 mm / D4 - Face plate 200 mm / D4, according to DIN 55029 - Fixed steady rest - passage diameter max. 60 mm - Follow-on steady rest - passage diameter max. 60 mm - Clamping plate 250 mm - Quadruple tool holder - Shaft fixing device - Protection device for tool holder - Slip clutch - Micrometer longitudinal stop - Coolant device - Extendable chip tray - Frequency converter - Foot pedal with brake function according to CE - Splash guard - Thread gauge - LED machine light - Digital speed dis ...
bore capacity in steel (diameter): 50,0 mm arm length: 350 - 1.590 mm workpiece height max.: 645 - 1.240 mm turning speeds: 25 - 2000 U/min spindle taper MT: 5 MK base plate: 980 x 1.600 mm threading: 42 M quill stroke: 320 mm total power requirement: 4,0 kW weight of the machine ca.: 3.500 kg. range L-W-H: 2450 x 980 x 2840 mm Description : - Large-sized base plate - ideal for processing large workpieces - Thick-walled, polished column for increased sliding properties of the boom - Extension arm and drill head with independent hydraulic clamping - Simple height adjustment of the extension arm using a lifting motor - Ideal for drilling, countersinking, reaming and thread cutting - Hardened and ground gears, running in an oil bath - Good sliding of the drill head on the boom thanks to the ground surface scope of delivery : - Cube table - Reducing sleeves MK 5/4, MK 4/3, MK3 / 2 - LED mach ...
bore capacity in steel (diameter): 60,0 mm arm length: 350 - 1.600 mm workpiece height max.: 665 x 1.250 mm turning speeds: 38 - 2.000 U/min spindle taper MT: 5 MK base plate: 960 x 1.760 mm threading: 42 M quill stroke: 325 mm total power requirement: 4,0 kW weight of the machine ca.: 3.800 kg. range L-W-H: 2.600 x 1.100 x 2.770 mm scope of delivery : - Cube table - Drill chuck arbor MK 5 / B 16 - Reducing sleeves MK 5/4, MK 4/3, MK3 / 2 - LED machine light - First filling with Shell Tellus 46 - coolant device - Frequency converter - Digital speed display - lift motor - hydraulic motor - Height-adjustable protective cover - operating tool The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1200 mm table width: 800 mm weight: 153 kg With the new mobile lifting table from Siegmund you can get there quickly and easily to the ideal working height. Set new standards in ergonomics as well Flexibility and benefit from the wide range of possible uses. The stable steel construction offers stability even during the Adjustment of the working height. Maximum load capacity including perforated plate 500 kg Working height between approx. 700 and 1,000 mm including 16 hole plate: - through hardened tool steel X8.7, - plasma nitrided and BAR coated - Hole Ø 16 mm - Holes surface 50x50 mm grid - Material thickness 12 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40.0 t chamfer lenght: 1600 mm distance between columns: 1200 mm column arm: 200 mm ram stroke speed: 60.0 mm/sec return speed: 80. mm/sec work speed: 60.0 mm/sec work stroke: 100 mm table height: 760 mm table width: 150 mm oil volume: 130 ltr. voltage: 400 Volt Control: ESA E21 total power requirement: 4.0 kW weight: 3030 kg range L-W-H: 2050 x 1800 x 2030 mm Demonstration/demo machine () From our showroom (like new) With very few operating hours Furnishing: - compact hydraulic press brake - BERNARDO NC control model E21 - swiveling control panel - electrical adjustment of the backgauge - Back stop on recirculating ball spindles - electrical adjustment of the immersion depth - Laser protection device in front - Upper deer foot tool - divided - Tool holder with quick change system - Universal die block - side + rear protective device - 2x front support arms - movable double ...
pressure: 160 t chamfer lenght: 3100 mm distance between columns: 2600 mm column arm: 250 mm ram stroke speed: 90.0 mm/sec work speed: 7.5 mm/sec return speed: 80.0 mm/sec work stroke: 160 mm dayligth: 395 mm table height: 900 mm back stop - adjustable: max. 800 mm oil volume: 200 ltr. voltage: 400 Volt total power requirement: 11.0 kW weight: 7524 kg range L-W-H: 4250 x 1900 x 2550 mm Furnishing: - DELEM CNC control model DA-66T graphic/touch screen 2D graphical programming 17 TFT color screen with high resolution Bending sequence calculation Product programming and real size display USB interface intuitive, graphical entry of profiles Automatic calculation of features: tool safety zones, Press force, bending tolerance, crown setting, stretched Length, embossing force, flattening, automatic rounding calculation Radius programming Graphic tool and product library Collision mo ...
pressure: 160 t chamfer lenght: 3760 mm distance between columns: 3250 mm column arm: 250 mm ram stroke speed: 90.0 mm/sec work speed: 7.5 mm/min return speed: 80.0 mm/sec work stroke: 160 mm dayligth: 395 mm table height: 900 mm oil volume: 200 ltr. voltage: 400 Volt weight: 8514 kg range L-W-H: 4910 x 1900 x 2550 mm Furnishing: - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - SICK light barrier in front of the machine - Upper tool, deer foot - Lower tool, die block with 4Vs - manual table crowning - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 400 mm ram stroke speed: 200 mm/sec work speed: 10.0 mm/min return speed: 165 mm/sec work stroke: ca. 350 mm dayligth: ca. 660 mm oil volume: 450 ltr. table height: 830 / 950 mm table width: 75.0 / 60.0 mm voltage: 400 Volt total power requirement: 18.5 kW weight: 13440 kg range L-W-H: 5150 x 2050 x 3150 mm current new price approx. 90.000 euros special price on request ------------------------------------------------------ ULTIMA PLUS electro-hydraulic press brake with: increased installation height .. approx. 660 mm increased cylinder stroke .. approx. 350 mm ----------------------------------------------------- - in checked condition - machine video - https://www.youtube.com/watch?v=chgCaXLnpa8 Equipment: - CNC electro-hydraulic die/press brake - CYBELEC CNC control DNC 880 S swiveling control p ...
Turning length: 705mm, turning diameter: 230mm, travel X1/X2: 165mm/195mm, travel Y: 100mm, travel Z1/Z2: 700mm/702mm, bar passage: 51mm, speed: 6000rpm, tool positions: 2x12. Machine dimensions X/Y/Z: approx. 5100mm/2200mm/2500mm, weight: approx. 8400kg, control: Fanuc 31i-B, operating hours: 1565h, spindle hours: 506h. Includes transformer, chip conveyor, filter system, and cooling unit. The cabin door window is broken. Documentation available. An on-site inspection is possible.
bore capacity in steel (diameter): 60 mm arm length: 1600 mm workpiece height max.: ca. 1300 mm borehole diameter: in Stahl 80 mm borehole diameter: in Guss 100 mm threading in St 60: M55 mm spindle turning speed range: 29-1.450 U/min Spindle Speed: 12 Stück boring spindle: 100 mm morse taper: MK5 spindle stroke: 350 mm total power requirement: 7,5 kW weight of the machine ca.: 4.600 kg dimensions of the machine ca.: 2600x1100x3200 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Turning length: 705mm, turning diameter: 230mm, travel X1/X2: 165mm/195mm, travel Z1/Z2: 700mm/720mm, bar passage: 51mm, speed: 6000rpm, tool positions: 2x12. Machine dimensions X/Y/Z: approx. 5100mm/2200mm/2500mm, weight: approx. 8200kg, control: Fanuc 31i-B, operating hours: 1407h, spindle hours: 343h. Includes transformer and chip conveyor. Documentation available. An on-site inspection is possible.
Key data: 3300 KW
We have 28 unit diesel main engine MTU with their gear boxes. For more information, do not hestitate to contact with us. Engines 1981 model but some of them revised 2010 by MTU.
Robot ABB Robotics IRB 1600 8/1.45 IRC5 M2004 , complete Control: IRC5 M2004 Number of axes: 6 Max. load capacity: 8 kg Max. working range: 1450 mm Year of Make: 2008 Scope of delivery: robot, controller, cable, teaching panel, circuit diagrams 2 weeks commissioning warranty. No further warranty. In addition, spare parts are always available from stock. The robot is fully functional and can be visited. Forwarding costs on request or pick-up on site.
1-deck swashscreen (expandable to 2 decks) with a screening area of 1.80 m²/deck, drive 4.0 kW via V-belt (engine renewed). Including 1 pc. sieve insert (not strung; stainless steel blank).
x-travel: 1600 mm y-travel: 4000 mm z-travel: 1200 mm workpiece weight: 3500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 704 KW, 880 kVA, 400 V
Brand Elbe Model No.: MT-825 CA Year of Make: 2007 Serial Number: 10330 Operating hours (read) < 500 Capacity (KvA) 880 Capacity (Kw) 704 Engine brand MTU Engine model 16V2000 Capacity motor (Kw) 720 Fuel Diesel Alternator brand Leroy Somer Alternator model LSA49.1L9 C6 S/4 Voltage 400 Frequency (Hz) 50 1500 rpm Amperes (A) 1270 Dimensions LxWxH (mm) On request Weight (Kg) approx. 17000 Quantity in stock 1 Made in Germany Comments Complete set ex Standby, for sight in our yard Condition of sale As / is present condition, functional take out of order
maximum number of results exceeded
please refine your search
