136,830 used machines on RESALE, but how to find them? Machine Search
Weight range: 0.25 to 3 kg Bag sizes: 60 x 25 x 160 mm min. 220 x 130 x 450 mm max. Application: Dry, free-flowing products, powdered, granular or piecemeal Typical examples: flour, sugar, tea, flakes, detergent, building powder, spices, sweet fruits
Max bending length: 1020 mm Max. sheet metal rod: 2 mm steel motor upper cheek adjustment via foot switch manual rear stop diverse bending rails
25 lfm shelf shepherd type R3000 Ne- and used goods, see pictures Height 2.5 m Depth 40 cm Load/fold 150 kg Field width 128 cm Negotiation price: € 1,560,-- net from stock Offer consists of: 20 pcs stand or frame, 2.5 m, galvanized new 114 pcs. shelves, 150 kg load/compartment, galvanized used 7 St. Cross Associations for Stiffening 6 levels per field (several are of course possible at an extra cost) Field width also available in 100 cm! Goods are in stock. Transport and assembly possible on request. Visit possible at any time by appointment. More information on request. Constantly over 5000 lfm pallet racks in stock by numerous manufacturers. (changes and errors in the technical data, information prices and intermediate sale reserved! See our Terms and Conditions, all prices excl. VAT from stock) Purchase / Sale We are looking for, or o ...
Laser printer for plastics FARSOON eForm 3D built in 2017. The printer is offered with complete equipment for preparing powder and cleaning prints. The equipment was used to a small extent for about 12 months, it worked for about 2000 hours. The device operated in a gas shield from a cylinder. Complete with printer: 8 nitrogen regulators. Technical data of the FARSOON eForm 3D printer: - open control software: any modification of printing parameters - laser type: CO? - laser power: 30 W - dimensions of the printing chamber (W × D × H ) : 250 × 250 × 320 mm - single print layer: 0.06 ~ 0.3 mm, adjustable - maximum creation / build speed: 0.8 l / h (depending on the material) - precise scanning system: Galvo - scanning speed: 7.6 m / s - power requirements: 380 VAC, 50/60 Hz, 16 KVA, three-phase five-wire - maximum temperature in the chamber: 190 degrees C - heating el ...
used
Weight: approx.4500 KG mash. No.: 6517991 General/technical data: Vertical CNC machining center in a very good, almost new condition, first-hand with very little operating hours. Travel: X= 670 Y=450 Z=470 mm Rapid response: in X and Y = 24m/min, in Z =20m/min Spindle motor: 10 KW Spindle speed: from 50 to 4,500 rpm Spindle cone: SK 40 Control: Siemens 810 M GA 2 Dimensions clamping table: 900 x 420mm max table load: 300 kg Distance spindle head to top of the table: 630mm spindle center to stand face: 470mm Tool slots in the magazine: 24 pieces DIN ISO 40 max. tool diameter: 110mm to 125mm tool length 100mm to 280mm tool length Beuvvquh2i Dimensions of the machine approx.: 2200 x 3000 x 2950 mm (without operator, service and chip conveyor environment) Accessories/ Optional equipment: â?¢ external coolant system with 2 pumps â?¢ Chip conveyor with ...
Pure water unit ENVIROFALK Performance in continuous operation 15 sqm / h max 18 sqm / h CA 2 trailers full of material Year 2009 / was for 1 year in use then the production has been discontinued. complete with all documents and control New price 260.000,-€
Farymann 28 P 10, 2 cyl. Diesel engine air cooled, approx. 16 kw / 22 HP / 2,500 1/min., capacity approx. 1,300 cc, engine kpl.mit air filter, alternator, and starter.
Thyristor-controlled, pneumatic point welding pliers with timer and compensation device 6kVA water-cooled
The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The vertical milling center FADAL VMC 2216 FX was manufactured in 2007 by the FADAL concern in the USA. The machine is equipped with FANUC Oi-MC numerical control. The milling machine can process workpieces weighing up to 450 kilograms. Machine travels in the X, Y, Z axes are 550 mm, 400 mm and 500 mm, respectively. The spindle revolutions of the CNC milling machine reach 8000 rpm. The center has a warehouse for 21 tools. Perfect for working with single details as well as for larger-scale processing. Technical data of the FADAL VMC 2216 FX machining center - CNC control: FANUC Oi-MC - table length: 406 mm - table width: 990 mm - maximum weight of the workpiece: 450 kg - X axis travel: 550 mm - Y axis travel: 400 mm - Z axis travel: 500 mm - maximum spindle speed: 8000 rpm - tool magazine: 21 - handle: SK 40 - spindle motor power: 11.2 kW - power demand: 35 kVA - power o ...
Vickers hardness tester of the extra class Modular design - as stand alone hearing tester or as a fully automatic machine. cheapest fully automatic machine worldwide As a full automatic incl. - 6-fold turret - 5 MP camera - 2 lenses (2 more optional) - motorized XY table - Overview camera - first-class hardness testing software IMPRESSIONS - incl. automatic hardness course CHD, NHT, RHT - additional software - modules for 2D / 3D mapping, screw testing ISO898, edge finishing, etc. - motorized lifting spindle - Autofocus, auto brightness + contrast ... This is THE quality machine at a fair price request now without obligation!
used Treif Falcon portion cutter incl. scale and the sorting station, year of construction 2006, portioning to exact weights, 360° scan for bone-in and boneless products, max. infeed length of 820 mm, depending on the product up to 240 portions per minute, the machine is equipped with a smooth curved blade for products without bones, bone-in version optionally available, products up to -3° C. You are very welcome to inspect and test the machine in our facility in Koblenz, Germany.
Capacitive: 60 kg 6 axes simultaneously controlled by Fanuc Teach-In System ; Very good
The vertical milling center FADAL VMC 15XTL was manufactured in 2007 in the United States by the FADAL brand. The machining center is digitally controlled by Fadal. It has a table size of 870 x 400 mm. The milling machine is designed for processing materials weighing up to 340 kg. It is equipped with a magazine for 21 tools. The spindle speed of the machining center, on the other hand, reaches 7500 rpm. Technical parameters of the FADAL VMC 15XTL CNC milling machine - CNC control: Fadal - working table length: 400 mm - working table width: 870 mm - maximum table load (evenly distributed): 340 kg - number of tools in the magazine: 21 pcs. - spindle drive power: 5.6 kW - maximum rotary speed of the vertical spindle: 7500 1 / min. - minimum distance between the spindle and the table: 101.6 mm - maximum distance between the spindle and the table: 609.6 mm - travel length in th ...
GUK Slitting Machine RS 21/760 Technical details: -No double bows, false bows and no risk of mixing! -Insensitive to static charge -approx. 20% cost savings compared to processing batch goods -Automatic control of the cutting position -Synchronous control of the print mark -Installation of code readers additionally possible -Storage in maintenance-free needle and ball bearings -Paper roll on top, single or double roll stand -With and without integrated adhesive table -Drive left or right, with chain or timing belt -Smallest fold 15 mm -With automatic roller changer ARW 21 Specifications: -Min. format: (WxL) 60 mm x 105 mm -Format: (WxL) 210 mm x 315 mm -Roller outer diameter: max. 600 mm -Roll core diameter: Europe 70 mm USA and Japan 76 mm or 152.4 mm or 3 inch or 6 inch -Power: 300/minute, depending on section length -Capacity: For paper roll by. 600 mm, sectio ...
Spare parts from a Fraesmaschine Webo Roeperwerk type Gradumat Table size approx. 12501000mm, complete control Fanuc Y.O.M. 1987 such as board control panel, glass mass staebe, servoverstaerker, motors, ball roller spindles, feed motors, uvw. Price on request No more vertical head. Special price
Capacity : 60 kgs. 6-axis simultaneously controlled by Fanuc Teach-In System ; Very good
approx. 14 running metres, H: 550cm, compartment load: 3000 kg, pallet racks, heavy duty racks, high racks, industrial racks, shelves immediately from stock Data: H : approx. 550 cm D : approx. 110 cm L : approx. 14 running metres Load: 3000 kg compartment load Stand in galvanized Trusses 270 x 14 x 5 cm, D30 Trusses in orange Brand new BLT / PR55 manufactured in Europe & tested according to the current standard DIN EN 15512. 100% quality at the best price. Shelf consists of: 06 x Stand approx. 550 cm x 110 cm, disassembled. 30 x traverse approx. 270 x 14 x 5 cm, D30. 60 x locking pins. Levels: Floor + 3 60 pallet spaces incl. floor spaces. -- IMMEDIATELY AVAILABLE MULTIPLE TIMES-- Price: 2220,00 € net plus legally valid VAT You will receive an invoice with VAT. The pre-assembly of the frames can be done by us for a small surcharge of 12.50 € / net per piece.
used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 30 S Year of construction: 2009 Serial No.: 109138 specifications: Pressing force: 30 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Height from the ground: 1,310 mm Bale size: 1,200 x 800 x 800 - 1,100 mm Bale weight: up to 270 - 360 kg Drive power: 7.5 kW Cycle time: approx. 29 sec. Pressing time: approx. 14 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)
Duerselen 7-fold drill head; suitable for Duerselen Corta paper drilling machines; was developed for aviation, stapling for flight maps; Abstaende see picture. ; ready for use. At this point we allow ourselves to note that all offered machines are in our unrestricted possession or access and are present in our warehouse. Visits and demonstrations are possible on request in our premises. We would also be pleased to inform you about our complete stock, as only part of our portfolio is presented here.
Barrel filling line complete (new Waagevon Bizerba, control panel and filler neck Bedieteil Bizerba iS30 Scales Bizerba type 2000/4000 VE-L 2250 piece barrel bag (new) with 3500 piece barrel bag sealers (new) NETZSCH with dosing unit BJ. 1983 with 80 piece barrels with lids and 80m EW pallets
Qty 1 x Pomini Model P270 Banbury internal mixer, M/c no. 362, Year: 1996, HDM style rotors (2 wing equivalent), PYH Dust stops, Hydraulic drop door discharge with Linear actuator, Vickers hydraulic power pack, Unidrive gearbox with couplings (11D type, 1000HP rating). Pneumatic hopper. Without motor or controls. Can be supplied with or without gearbox. Quote for new motor and controls on request.
Currently available in stock: approx. 1,650 pcs. Technical data for the shelf carrier: Manufacturer: META Type: META FIX + META CLIP The scope of delivery includes: 12x Shelf carrier, used Design: f. shelves Material colour: complete galvanized Total height: approx. 53 mm Total width: approx. 18 mm Material thickness: approx. 1.2 mm Weight | Pcs. approx. 0.012 Kg Your contact persons in our company: Mr. Andre Evering Mr: Mario Klöver Mr: Falk German General information about the product: This item is available for pickup only. A further desired transport or a dispatch of this article is associated with additional costs, which are separately depending on the place of delivery or scope of delivery.
1 x Farrel F370 mixer chamber and hopper M/c no. 081110, Date: November 2009, SSA dust stops, 4 Wing Rotors, Drop door with Linear actuator, Base Plate with Toggle Latch. Pneumatic hopper with extension neck (Floating weight looks to be in good condition). Parts available: Body, baseplate, Toggle Latch, actuator and Pneumatic hopper with extension neck.
Table size 2400 x 810 mm Feed speed 1 - 10000 mm/min Headstock travel 810 mm (Z-axis) Height of the machine 4000 mm Pull bolts MAS 403-P40T-I Table longitudinal displacement 2000 mm (X-axis) Table Transverse Displacement 810 mm (Y-axis) Spindle front face to table top 100 - 910 mm Distance from the floor to the table 1200 mm Distance between spindle center and column front 825 mm T - Slot No. 5 T - Slot Size 18 mm T - Slot Pitch 150 Max. load on the table 2500 kg Spindle cone BT-40 Hourly spindle speed 6000 rpm Footprint (L x W) 5400 x 3450 mm Weight of the basic machine 17000 kg Total connected load 50 kVA (basic standard machine), 60 kVA (basic standard machine with high-power spindle)
Qty 1 x Farrel Bridge 4 roll inverted L Lab calender, Roll width: 381 mm roll Ø: 152 mm Roller bearings Speed: 2,38 – 23,8 1/min., adjustable Nip adjustment: by hand Friction: 1:1 / 1:1,21 Drive: 9,25 kW, 380 V Measurement: ca. 1.765 x 1.687 x 1.800 mm (L x W x H) Weight: ca. 1.800 kg in. control cabinet
The scope of delivery includes: 01x Truss strut, new Manufacturer: Mecalux Material colour: sendzimir galvanised Overall length: approx. 1,052 mm Center-center hole: approx. 998 mm f. Frame profile width: 100 mm Ø drill hole: approx. 10 mm U-profile dimensions: 70 x 30 mm Material thickness: approx. 1.5 mm Weight: 1.5 kg | Pcs. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.
1 x Fanuc Back Plane 3 Slot A05B-2316-C105 1 x Fanuc A16B-3200-0042/05B900514 Board 1 x Fanuc A16B-1 212-0871/17C906140 Power Supply Board Alternative search terms A05B2316C105 A16B3200004205B900514 A16B1212087117C906140 A16B-3200-0042 A16B-1212-0871 A16B12120871.br/> .br>.br/>>A16B32000042.br/>.br/>.br/>.br/>.br/>.br/>.br/>.br/>.br/>
Sell a well-preserved triple honing machine from Stanko. The machine was in use until it was dismantled. The dimensions of the machine are LXWXH 800mm x 1100mm x 1650mm. The weight is 800kg. The dimensions of the control cabinet are LxWxH 350mm x 950mm x 1550mm. The weight is approx. 150kg. If you have any questions, just get in touch. The machine can be viewed by prior appointment. Shipping, on 2 pallets, is no problem. Please inquire about shipping costs with zip code. Furthermore, the machine can be delivered and unloaded in the immediate vicinity with its own crane truck and against assumption of costs. On-site loading is no problem and free of charge. The sale is without warranty and guarantee. The return is excluded. All information without guarantee.
1 x Refurbished Pomini Farrel model P160 Banbury internal mixer, Original year of manufacture 1984, Rebuilt in 2017 (not used since), Mixing chamber volume 160L Net, Batch size at 75%FF and SG 1.0 - 120kg, 2 wing rotors, PYH hydraulic dust stops (new), hydraulic drop door discharge with linear actuator and spade latch, Pneumatic hopper, Unidrive gearbox type NF160, rating 640HP, Input speed 1500 rpm, output 39.6rpm. with 470kW, 500V DC variable speed motor. Mechanically complete but currently without electrical controls.
Manufacturer: Microcut, Type: Fagor CNC 800T, Year: 2010, Control: Programm, Year :2010
Good day have with this machine a top TECA print up to 4 colours! Carrée and pad cleaning! Absolute Professional machine. If you have questions just email!
Manufacturer: Farbmischer, Type: Biaxo , Year: 2008, Control: Not Aus/an-aus/Frequenzregelung Mischbetrieb, Year :2008
QTY 1 x Pomini VIC1.8-PX1.6 Tandem Lab mixer, Machine number 9912, date 1990, Modern frame design with unitized fabricated steel base, Anti friction roller bearings with floor lubrication, 22kW DC variable speed motor. Rotor speeds 0-230rpm Torque montioring sensors. Siemens PLC control system with S7-300 CPU (combined with original S5). Desktop computer interface. Left hand mixer: Pomini PX1.6 tangential rotor type, Volume 1.6Litre, 2 wing rotors, FY type bronze dust seals, Jacketed chamber for heating or cooling, Hard Chrome plated chamber and rotors, Chamber sides can manually swing open for cleaning/maintenance (by removing 4 bolts on each side), Pneumatic oil injector, Pneumatically operated discharge drop door with linear actuator, Pneumatically operated hopper load door, Pneumatic ram with transducers fitted to monitor floating weight position. Proporti ...
Manufacturer: Stöber Frequenzumrichter, Type: FAS 1015/B, Serial number: 794, Serial number: 1167218,
Manufacturer: Stöber Frequenzumrichter, Type: FAS 1015/B-1, Serial number: 1292, Power Output: 1,5 KVA,
Maximum cutting length: 4000 mm Maximum sheet thickness: 4 mm steel Driven back gauge to 1000 mm Page fence and table extensions Cutting length limit Cutting edge lighting Protection fence, roll with safety switches Weight: 8500 kg
Doppelschleifbock, water cooled-Schleifscheibe max Ã? 350 x 50 mm (neuwerig) speed 1400 RPM engine power 1.8 KW 380 Volt L 1050 B 750 H 1250 mm - 79. weight 300 kg
Manufacturer: Stöber Frequenzumrichter, Type: FAS 1015/1, Serial number: 0193, Power Output: 1,5 KVA,
maximum number of results exceeded
please refine your search
