extruder screw barrel used for sale

Twin screw extruder APV Baker, int. ref. APV 5 (Baker Perkins) Ø50/25D + additional liner 10D(for 35D), this was totally revamped in 2017, liners and screws are in quite good conditions, reduction gear was replaced in 2021. Operator panel with recipes and 14 heating zones, all in good conditions. Find more here - / Contact us at -

Description Single Screw Extruder Screw diamter 60 L/D 25 Motor power 27,5 kW

Description Conical Twin Screw Extruder Screws Diameter 45 - 97 Screws Length 390 Barrel zones 3 Nr.1 vent Thermoregulated screws Motor power 15,4 kW Forced feed

Description Conical Twin Screw Extruder screw diameter 80 Thermoregulated screws 1 vent Installe dnew lectrocal motor in 2018 Unstalled new inverter for electrical motor in 2018 Motor power 68 kW Retrofit of PLC with BCtouch control

Control panel: Siemens SIMATIC HMI, connected load: 80kW, weight: 1.85t, operating hours: approx. 4500h, with Kreyenborg feed hopper, year of manufacture: 2017, and Trendelkamp screen changer. Documentation is complete, on-site inspection is possible.

weight: 2,2 t extruder diameter: mm : : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

PVC PROFILE EXTRUSION LINE EVC BRAND, single screw extruder with 60 mm 28 LD, constructed in 1998, for 180 mm max width, 44 kw drive, control panel, Calibrating desk 3,7 m.long with 1 x 9 kw.pump, Caterpillar pull off unit, 180 mm wide, saw, 6,0 mt.long discharging table.

MARIS TWIN SCREW EXTRUDER, Loading hopper for regrinds, Barrel with 2 x 92 mm screws 40 L/D, co-rotating parallel screws for polyolefines, CEAR d.c.motor, N.2 vacuum degassing pumps, 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, Electrical control panel, The machine is offered as is or checked

MARIS TWIN SCREW EXTRUDER, Barrel with 2 x 92 mm screws 40 L/D, n.2 vacuum degassing pumps, co-rotating parallel screws for polyolefines, complete with 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, electric cabinet, The machine is offered as is or reconditioned

MARIS TWIN SCREW EXTRUDER, Type TM 85 LC 37 L/D, dosing unit for granulated materials, barrel with 2 x 85 mm co-rotating screws 37 L/D, max screw rpm : 152, vacuum degassing pump 4,5 kw drive, Present capacity 450 kg/h depending on materials and feeding rate, 64 kw drive, Constructed in 1992, offered AS IS or reconditioned, installed power - used power in work: about 60-65% : 64, screws diam.: 85 mm. 37 L/D, screws: co-rotating

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

Screw Diameter: 140 mm // Throughput: 900 kg/h

Screw Diameter: 75 mm // Throughput: 700 kg/h

Screw Diameter: 92 mm // Throughput: 800 kg/h

Screw Diameter: 130 mm // Throughput: 800 kg/h

Screw Diameter: 58 mm // Throughput: 450 kg/h

Screw Diameter: 50 mm // Throughput: 150 kg/h

Screw Diameter: 64 mm // Throughput: 480 kg/h

Screw Diameter: 27 mm // Throughput: 100 kg/h

General SKU299X419 LocationBarneveld MakeCoperion Werner & Pfleiderer GmbH Stuttgart TypeKP-120/250 KombiPlast Compounder Mach.No.20493087 Sizes Screw diameter120 mm Main Features Motor310 KW Inlet diameter200 mm L/D15 Specified Features - Double screw extruder Double screw extrudercheck Screw diameter120 mm L/D15 Counter rotatingcheck Electric heating4 Water coolingcheck DC-motor310kW, 440V, 1780rpm With variable speed drivecheck Screw speed365rpm Feeding with hoppercheck Feeding with metering screwSide feeder MaterialNitriding Steel 1.8550 Information Year of construction2004 With switchgearcheck (as is) Weight± 22.000 kg Extra SpecificationsComplete line with side-feeder, discharge screw and partially control cabinet info compounder: Krupp Werner &: Pfleidere GmbH typ: D315 EXT Single screw screw dia: 250 mm screw lengte:1500 mm. screw van be heated L/D: ...

A twin screw extruder is offered. Drive: ASEA electric motor type ACA 200-6L, 50.5kW, 1460rpm. Inspection possible by prior arrangement.

BANDERA TWIN SCREW PVC PIPES EXTRUDER, for pipes with min/max diam.40/200 mm., extruder with n.2 parallel counter-rotating screws Ø 90 mm, Throghput rate 400 kg/hr, missing of screenchamger (can be added separately), n.2 dies available 40 to 125 mm + 125 to 200 mm., Tooling from 40-200 mm (available diam. 100 mm for O-Ring), Bandera 6 mt.long vacuum calibration tank, IPM haul off unit, IPM saw, IPM belling unit, constructed in 1998, totally refurbished in 2006 by Plasco, machine now disconnected, offered RECONDITIONED., availability: immediate, working width: 40-200 mm Ø, capacity: 400 kg/h, conditions: disconnected, type: pipes extrusion line

This KUHNE KS45-24D compounding extruder was manufactured in 2006. Ideal for processing a variety of materials, it offers robust construction and reliable performance. Consider the opportunity to buy this KUHNE KS45-24D compounding extruder. Contact us for more information.

This LEISTRITZ ZSE60MAXX-48D was manufactured in 2012. A co-rotating twin-screw extruder, its designed for high-performance compounding of advanced polymer materials, including biodegradable polymers. Adaptable to various extrusion processes, its ideal for bioplastics, masterbatch production, or specialty compounding. Contact us for more information about this machine.

This Krauss Maffei KME 45 XS was manufactured in 2016. It features a 45 mm screw diameter, high-performance single screw with a 36:1 L/D ratio, and operates at speeds up to 120 rpm. Designed for high-pressure extrusion, it handles thermoplastics and compounds with a throughput of 150-300 kg/h. Consider the opportunity to buy this Krauss Maffei KME 45 XS single screw extruder. Contact us for more information about this machine.

Key data: 20 mm, 150 , 2150 U/min

with PE screw, Capacity approx. 350 kg/h complete with motor, gearbox and Heating tapes Good condition, immediately available

A counter-rotating side-feed twin-screw extruder Krauss Maffei used in the coextrusion process is available. Screw diameter: 40mm, material: rigid PVC, screw speed: 50rpm, throughput capacity: approx. 50-80kg/h, operating hours: approx. 42100h. Including roller guide with subframe. Documentation available. An on-site inspection is possible.

COMAC TWIN SCREW EXTRUDER EBC60, barrel with n. 2 x 60 mm. diam co-rotating screws, 42 L/D, spare : 2 screws and 1 barrel reconditioned to 100% performances, Mounted: screws + barrel in very good conditions, n.1 dosing unit with hopper, N.2 vacuum degassing points, d.c.132 kw Siemens main drive 400V 50 Hz, non-stop hydraulic screen-changer with 90 mm screens (available with fully automatic screenchanger, on separate request), hydraulic pack, fitted with strand die (available with water ring pelletizer on request) + stainless steel cooling bath with heat exchanging unit + air-blowing dryer, electric cabinet (for extruder, screen-changer, hydraulic pack), pelletizer for strands, TVV Cooling column for granule., constructed i n 2001, The line is offered totally or partially reconditioned (photos show the machine during reconditioning), installed power - used power in work: about 60-65% : 13 ...

Extruder 70 mm - 24 L/D with pipe head up to 63 mm, calibration tank 6000 mm Caterpillar extractor, saw

1 x David Bridge 15/18\ Dump Extruder with 40\ Face x 20\ die Roller Die. Spare parts available. Screw L/D 5:1, Crammer. Length of Barrel 7ft. Right angle turning unit for product flow. 200HP DC variable speed motor

Kobelco Twin Screw Roller Head Extruder (horizontal type), Model TSR-330 Roller die assembly (TSR-33H005H) 38in wide x 16in dia Roller die moves away from the extruder/mixer section via hydraulic ram. driven by 102kW DC variable speed motor through Hansen reduction gearbox (on flexible coupling so roller die can move forwards/back). Twin screw dump extruder 330mm screw dia driven by 90kW DC variable speed motor through Hanson reduction gearbox. In very good condition. Previously running underneath an F270 Banbury. Complete with all controls, manuals and documentation etc.

Francis Shaw 18/22\ Dump Extruder, Crammer feed Length of Screw 9ft 6\. Reliance 400hp D.C., 1150 r.p.m., 480 volt. Large Hopper/Chute to next floor level.

1 x Werner & Pfleiderer 400mm dia dump extruder, Type: EAE400, Fabrik nr 221284, Werk nr 416295, Year: 1985, double hydraulic crammer feed, feed section 965mm wide, L/D ratio 8:1, with 235kW DC variable speed motor, Sheeting head to produce up to 1000mm wide sheet. Complete with controls and hydraulics etc.

1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included.

We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information

Used EXTRUDER twin screw (TWIN SCREW EXTRUDER) for the production of cereal flakes: Producer: PAVAN Model: TT92 Year: 2002 Dimensions: 6580 x 4150 x 3000 Weight: 2400 kg Productivity: 500 kg / h Power: Description: A twin-screw extrusion device as a result of a continuous and automatic process of a great variety of flour and cereal starches / tubers, both mixed and pure. The materials from the dispensing unit are pre-mixed using a suitable device equipped with counter-rotating blades (double shaft mixer), and then enter the mixing tank for kneading and homogenization. From the mixing tank, through a suitable screw device (forced supply), the mixture is pressed into a group of cooking cylinders in which the cylinders are heated to the desired stage, according to a predefined and automatically controlled temperature profile. compatibility of extruder screws, which are repla ...

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

Multiple extruders

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.

Key data: 30 , 28 , 110

Plant for the production of filament for use in 3D printers Capacity up to 10 kg/h consisting of 30 mm extruder, stainless steel trough, puller and winder with traverse guide

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

According to the description below

Key data: 30 , 28 , 110

Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper

Extruder KE 90 x 30-D for manufacturing of von TPE foam and compact profiles screw diameter: 90 mm L/D ratio 30:1 (2700mm) extruder with 11 temperature-controlled zones (electrically heated by fluids) Siemens electric drive, motor 45kW at 2500rpm year of construction 1996, machine in very good condition (preliminary used in test operations) melt application device (gear pump) double profil head (also used for extrusion-coaded framework belts) electric equipment partially available extruder mounted on movable baseplate

Key data: 100 , 140

Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station � ...

Extruder Petersen VAP 65

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

Nordson / Puffe Extruder Plant Ex20 -1xPS01-1xPE20-1 for melting hot melt adhesives and thermoplastics, feeding as granules. Melting capacity according to the manufacturer's specifications up to 20 litres/h (EX20) Price: 45.000, -- € plus 19% VAT (Gross price incl. VAT 53.550, -- €) EXW Manufacturer: Nordson / W. Puffe Hotmelt-Technology Model No.: Ex20 -1xPS01-1xPE20-1 Year of manufacture: 05/2006 Serial No. 226260231/001 Power: 15 kW, connection 380V three-phase current Emergency stop, traffic light, CE mark Made in Germany Compact system mounted on a stable rolling frame (H= 198 cm, W= 160 cm, D= 110 cm) consisting of Nordson extruder, gear metering pump, Lenze worm drive, control cabinet with Allen-Bradley control, graphical user interface, storage tank, operating manual. Auxiliary: Labotec Minifeed Suction Conveyor MF60 Serial No. 12-103-00669 (Owner's man ...