extruder screw barrel used for sale

A screw compressor is offered. Maximum pressure 10bar, volume flow approx. 2020l/min (2.02m3/min) with separate compressed air tank, galvanized. Viewing possible by appointment.

Motor power: 11 kW Nominal flow rate: 1.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-2

Two identical compressors with integrated refrigerated dryer are offered. Pressure dew point: +3°C, rated power: 30kW, delivery rate (FAD): 5.31m³/min at 8bar, 4.77m³/min at 10bar, 3.86m³/min at 13bar, control: Boge Autotronic, fully automatic operation. Inspection is possible by arrangement.

Motor power: 7.5 kW Nominal flow rate: 1.0 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 900x625x860 mm Estimated weight: about 200 Kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-1

Motor power: 15 kW Nominal flow rate: 1.7 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-3

We can offer Krauss maffei extruder,moder ZE90A, manufactured in 2013, main motor power 884kw, large output, installed and used, auxiliary equipments available, serious buyer contact us.

Offered are 2 screw compressors with the following features per unit: Power: 15kW, pressure: 10bar, volume flow: 1950l/min (1.95m3/min), speed: 2930rpm, including sound enclosure, 1) year of construction 1989, operating hours: approx. 38100h, 2) year of construction 1986, operating hours: approx. 10600h. Inspection possible by appointment.

We can offer Krauss maffei extruder,moder ZE90A, manufactured in 2013, main motor power 884kw, large output, installed and used, auxiliary equipments available, serious buyer contact us.

L+Z Lathe WEILER Praktikant 160 – Partially Overhauled Machine in very good used condition – delivery on order, delivery time by arrangement! ✅ Technical data Year of construction: approx. 1990 Digital Display: 3-Axis (NEW) Max. turning diameter over bed: approx. Ø 320 mm Max. turning diameter via support: approx. Ø 198 mm Max. turning length: approx. 650 mm Bar passage: approx. Ø 40 mm Spindle speed: 96 – 2500 rpm Spindle nose: A 2 - 5 Drive power: approx. 2.2 kW Threading: Metric, Inch, DP, Module Tailstock: MK 3 Dimensions (LxWxH): approx. 1700 x 1000 x 1700 mm Weight: approx. 650 kg ✅ Accessories 3-jaw chuck 160 mm (NEW) Quick-change steel holder + 1 insert Electric Lining Guard (NEW) Work light (NEW) Complete machine documentation Emergency stop Various tension wrenches Coolant Setup L+Z Spindle  ...

Vacuum extrusion press 'UNIVERSA' PZG 40-40a with 400 mm Ø and 18.5 kW drive (expandable up to 55 kW). Maximum pressing pressure: 30 bar. Extruder incl. PZSVG 35a pre-press with 15 kW drive. Includes base frame with motor clamping device. In regularly serviced condition; last revision in 2022. Previous use: Production of ceramic roof tiles. Available for an extra charge: vacuum generator and various mouthpieces.

Reduction and transfer case for conical twin screw extruder Cincinnati Titan 58 Manufacturer: Eisenbeiss on behalf of Cincinnati Extrusiontechnik General overhaul included: • Checking the sprockets for damage with a special camera • New sealing of the drive and output shaft • New shaft bearing • New oil filling • Repainting Condition: overhauled, fully functional

Fully automatic capping machine PMFS100. High-precision mechanical design for seamless bottle positioning. Sliding cylinder modules for cap tightening. Intelligent control system with touchscreen. Electrically and pneumatically driven. Surfaces made of stainless steel or food-grade plastics (GMP-compliant). Suitable for mass production. Production capacity: 120 bottles/min, compressed air: 0.6kg/cm², air consumption: 20m³/h. Inspection possible by prior arrangement.

Offer 24204 Technical data: - Largest turning diameter over bed 420 mm - Center width 1000 mm - Spindle bore mm - Mounting cone of the tailstock quill MK 4 - Travel of the tailstock quill 200 mm - Spindle speeds 40 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches - Inch thread - Module thread - Drive 400 V - with: - 3 jaw chucks - SWS steel holder with 3 inserts - Space requirement approx. W 2800 x H 1250 x D 950 mm - Weight approx. 2200 kg

Key data: 7 , 13

As good as new with 2 years new equipment warranty Service NEW! ONLY 136 operating hours YOC 2023 with dryer, pre-filter and ES4000 Connect controller Technical data: Effective delivery rate 780 l/min Max. operating pressure 13 bar Tank volume 500 l Container-mounted version Engine rated power 7.5 / 10 kW / hp Electrical connection voltage / frequency 400/50 V/Hz Sound pressure level (4 m) 65 dB(A) Air outlet 3/4 inch Length 1940 mm Width 720 mm Height 1470 mm Weight 305 kg Free shipping throughout Austria

Key data: 230 mm, 460 mm, 25 U/min

Optimum D460x1500 lathe – fully functional Description: For sale is a used Optimum lathe D460x1500, built in 2006/01. The machine is fully functional and ready for immediate use in the workshop and production. It is ideal for turning medium-sized metal and steel parts. Technical data: Manufacturer: Optimum Model No.: D460x1500 Year of construction: 2006/01 Circumferential diameter over bed: 460–465 mm Circumferential diameter over upper slide: 270 mm Circumferential diameter without bed bridge: 690 mm Center width: 1500 mm Tip height: 230 mm Bed width: 300 mm Spindle bore: 58 mm Spindle cone: MK 6 Spindle mount: Camlock ASA D1–6 Speed range: 25 – 2,000 rpm⁻¹ Longitudinal feed: 0.031 – 1.7 mm/rev Transverse feed: 0.014 – 0.784 mm/rev Thread metric: 0.1 – 14 mm Thread imperial: 1/2 – 2 gears/inch Motor power ...

Technical data: - Operating hours 4248 h - Load hours 1978 h - Operating pressure 10 bar - Delivery rate 3.34 m³/min - Drive 400 V / 22 kW - Motor speed 3000 rpm - Space requirement approx. W 1300 x H 1250 x D 800 mm - Weight approx. 490 kg

Technical data: - Operating hours 20256 h - Operating pressure 13 bar - Delivery rate 4.09 m³/min - Drive 400 V / 26 kW - Motor speed 3000 rpm - Space requirement approx. W 900 x H 1750 x D 900 mm - Weight approx. 490 kg

Year of manufacture 1980s/90s Technical data: Tip height: 185 mm Center width: 750 mm Turning diameter over bed: 370 mm Spindle bore: 36 mm Bed width: 250 mm Speed range: 38 - 1600 rpm Tailstock mount: MK 3 Quill stroke: 110 mm Dimensions (WxDxH), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: - 3-jaw lathe chuck, brand: Röhm, ø 200 mm - Quick-change holder with 4 inserts - Bed stop - Chip tray

Key data: 20 mm, 25

single-screw laboratory extruder Collin E 20 M Output capacity: max. 5 kg/h (depending on material and processing conditions) Screw diameter: 20 mm, L/D = 25 Screw suitable for processing PE/PP (condition: excellent) Heating capacity cylinder: up to 300 C incl. mass pressure and temperature sensor Incl. motorized lifting device for the height adjustment of the processing unit incl. material funnel incl. clamping flange for nozzle attachment Total connected load: 17 kW Dimensions (L x W x H): 1,450 x 800 x 1,900 mm Weight: 300 kg Note: including complete documentation Condition: used, function-tested

1.0 PCS screw compressor system consisting of the The following components: 1.0 pcs Screw Compressor, Manufacturer: Almig, Type: Belt Drive 15 , Year of manufacture: 2013, Operating pressure: 10 bar, power 15 KW 1.0 pcs. Compressed air dryer Manufacturer: Prematic 1.0 pcs pressure vessel 1.0 Sr. Oil Separator

Key data: 75 mm, 30

Single Screw Extruder Cincinnati TALOS 75-30G Output capacity: max. 450 kg/h (depending on material and processing conditions) Screw diameter: 75 mm, L/D = 30 Screw geometry for processing HDPE/PP 11 x Tool Zones incl. TC Type J ITIB 3-pin Thermal Probe incl. mass temperature and pressure sensor Interface for succession via CAN Open Bus Machine control Cincinnati EXcXP-touch Drive power main motor: 125 kW Total connected load: 178 kW Machine weight: 2,200 kg Remark: incl. spare engine (used) without material hopper Condition: used, function tested

Manufacturer: KAESER Model: BSD 72 SFC Year of Manufacture: 2012 Machine type: Screw Compressor Rated Power: 37.0 kW Motor Speed: 2960 1/min Max. Operating Pressure: 8.5 bar Ambient Temperature: 3 degrees C / 45 degrees C

Key data: 2 , 10

New AGRE Alup screw compressor with filter unit (technically oil-free), for the operation of milking robots. IMMEDIATELY AVAILABLE from the Hengsberg warehouse in Styria! We are also happy to take care of the delivery and commissioning of the compressor and ongoing maintenance of existing compressors of the brands AGRE, Alup and Atlas Copco. Drive: Efficient IE3 motor with belt drive Control: Infologic² Connect Refrigeration dryer and 270 litre container integrated Includes filtration for technically oil-free operation Performance data Volume flow at operating pressure 9.5 bar: 0.29 m³/min Operating pressure min. / max.: 5.5 / 10.0 bar Total power consumption at 9.5 bar / full load: 3.7 kW Rated power motor: 2.2 kW Pressure dew point refrigeration dryer : approx. +3 °C Dimensions and weight Length x width x height 1540 x 600 x 1350 mm Weight 205 kg Compressed a ...

Key data: 5 , 10

Oil lubricated screw compressor Cooling: Air-cooled design Drive: Efficient IE3 motor, belt drive Control: Speed-controlled with frequency converter Control: Infologic² Connect Refrigeration Dryer: Integrated Filtration optionally available Performance data Volume flow at operating pressure 7.0 bar 0.33 - 0.75 m³/min Operating pressure min. / max. 4.0 / 10.0 bar Total power consumption at 9.5 bar / full load 7.7 kW Rated power motor; IP55 5.5 kW Oil volume 3.2 lt Pressure dew point refrigeration dryer approx. +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C Cooling air demand 1140 m³/h Free fan pressure 30 Pa Sound level 61 dB(A) Voltage / PH / Frequency 400 / 3 / 50 V / Ph / Hz Refrigeration dryer power (230V/50Hz) 0.19 kW Dimensions and weight Length x width x height 1540 x 600 x 1375 mm Weight 230 kg Compressed air outlet 1/2 "  ...

Key data: 7 , 10 , 1

Oil lubricated screw compressor Cooling: Air-cooled design Drive: High-frequency motor with 1:1 direct drive Control: Speed-controlled with frequency converter Control: Aircontrol 5.0 (4-20mA) Refrigeration dryer: Integrated, refrigerant R134a Filtration: incl. cyclone separator Performance data Volume flow at operating pressure 7.0 bar 0.28-1.25 m³/min Operating pressure min. / max. 5.0 / 12.5 bar Total power consumption at 10.0 bar / full load 9.3 kW Rated power motor; IP55 7.5 kW Oil quantity 3.5 lt Pressure dew point refrigerant dryer (20°C 100% RH) +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C ∆ T above coolant temperature 8 °C Cooling air requirement 2200 m³/h Free fan pressure 30 Pa Sound level 62 dB(A) Voltage / Frequency 400 / 50 V / Hz Refrigeration dryer power (230V/50Hz) 0.27 kW Dimensions and weight Length x width ...

Extrudeuse CM EVOLUTION PLAST type CM-EVO 230 Année. : 2019 Puissance : 50 KW Tension : 400 VOLTS Poids : 4000 KG

Type M14 M.A. 16,2 EFFICIENCY 27% TURN TO CLOSE 15 RATIO 16:1 MAX IT 136 MAX OT 2200Nm

KERN - Universal lathe CD 480 - Control - Manual Plus -Built in 1994 -1029 operating hours -Prisms / flat guides hardened -Circulation / turning diameter over bed 475mm -Circulation/turning diameter via face slide 260mm -Slide path / plan 260mm -Turning length 1500mm -Spindle passage 78mm -Speed range (V-constant) 1-3000 rpm -Feed range / plan 0.001-1000 mm/rev -Feed range / longitudinal 0.001-2000 mm/rev -Rapid traverse / plan / longitudinal 5/10 m/min -Tailstock MK 5 - 120mm quill path -Multifix with insert -Röhm - Three-jaw chuck 250mm -Automatic central lubrication -Coolant device -Complete machine documentation Dimensions: LxWxH 3.5x1.4x1.8 meters / Weight: 3000 kg

GALLIC 16 N lead and pull spindle lathe with ACU-Rite digital display - Turning diameter over support 200mm - Turning diameter over bed 320mm - Tip height 160mm - Center width 1000mm - Speed range 45-2500 rpm - Spindle bore 40mm - Automatic feeds X/Z axis LxWxH 2.4x1x1.7 meters / Weight 1600Kg

VOEST DA 360 - Lead & Pull Spindle Lathe -Heidenhain digital display -Peak height above bed 400mm -Turning diameter over bed 800mm -Turning diameter over support 500mm -Turning length 1000mm -Rod passage approx. 87mm -Speed range 14 - 1000 rpm / 18x speeds -Automatic length / face feeds -Automatic input Z-axis -Tailstock MK 5 -Wedge bar chuck 250mm -Multifix base holder with insert -Work light -Machine feet -Documentation Dimensions: LxWxH 3x1.5x1.7 meters / Weight 3500 KG

Leit & Tension Spindle Lathe WEILER COMMODOR 180 GSD / New -Unused -Exhibition machine / zero operating hours -CE marking -3 - Axis Digital Display -Tip width 1000mm -Tip height 180mm -Spindle passage 56mm -Circumferential diameter over bed 380mm -Circumferential diameter via face slide 215mm -Speed range / gearbox 25-2000 rpm -Automatic longitudinal/plane feeds -Thread/Inch/Metric/Diametrical -Tailstock / quill cone MK 4 -Quill stroke 150mm -Coolant device -Multifix with insert -Three-jaw chuck 200mm -Work light -Swarf back wall -Documentation Dimensions: LxWxH 2.6x1.6x1.7 meters / Weight 2000Kg

GDW LZ 350 incl. 3-axis digital display -Tip height 175mm -Circumferential diameter over bed 310mm -Circumferential diameter over face slide 195mm -Tip width 800mm -Spindle passage 43mm -Speed range 45-2000 rpm -Automatic longitudinal/plane feeds -Tailstock / Quill Stroke 110mm -Thread/Metric/Inch etc. -Multifix with inserts -Three-jaw chuck 200mm -Collet device incl. 22 x collets -2x Emergency/Off -Coolant device -Various interchangeable wheels 5 pieces -Drill chuck -Running tip -Swarf back wall -Machine feet -Miscellaneous tools -Documentation Dimensions: LxWxH 1.85x0.9x1.5 meters / Weight 850Kg

WEILER CONDOR VS 2 from university (test laboratory) -Guided tours "as good as new" -Tip height 165mm -Circumferential diameter over bed 330mm -Tip width 800mm -Speed range 28-2800 rpm -Automatic longitudinal/plane feeds -Spindle passage 40mm -Thread/Metric/Inch etc. -Collets - quick clamping device incl. collets -Vierbackenfutter-Röhm -Face Plate -Four-jaw chuck faceplate -Lining protection -Multifix with inserts -Emergency stop -Documentation Dimensions: LxWxH 2x0.8x1.6 meters / Weight 900Kg

Lead & Pull Spindle Lathe EXCELLO - DLZ 500 SL -Tip height 250mm -Turning diameter over bed 500mm -Turning diameter over support 310mm -Center width 3000mm -Rod passage 65mm -Speeds: 28-1400 rpm -Automatic longitudinal/plane feeds -Three-jaw chuck 250mm -Four-jaw chuck 250mm -Multifix base holder with inserts -Bezel -Tool cabinet -Documentation Dimensions: LxWxH 5.5x1.4x1.6 meters / Weight 3500Kg

Guide & Tension Spindle Lathe GEMA LZ 200 -Three - Axis Digital Display "NEW" -Guided tours " VERY GOOD" -Tip height 200 mm -Center width 1000 mm -Turning diameter over bed 400mm -Turning diameter over support 200mm -Spindle passage 54 mm -Automatic longitudinal/plane feeds -Speed range 36-2200 rpm -Tailstock MK 4- Adjustment 200mm -Three-jaw chuck 250mm -Electric lining protection -Multifix with inserts -Coolant device -Work light -Machine feet -Chip tray Dimensions: LxWxH 2x1.2x1.6 meters / Weight 1800Kg

Lead & Pull Spindle Lathe NARDINI MS 125 E -Peak height above bed 150mm -Turning diameter over support 140mm -Tip width 500mm -Spindle speeds 50-2500 rpm -Spindle passage 34mm -Automatic longitudinal/plane feeds -Thread/Metric/Inch -Tailstock MK3 -Collet quick-clamping device with various collets 173E -Tool cabinet with machine-related accessories -Swarf back wall -Documentation Dimensions: LxWxH 1.6xx0.7x1.6 meters / Weight 1200Kg

Overview  This pilfer proof capping machine was manufactured in 2022 by the Spanish company CTM Ingeniería. It has been used for only 1.5 years under light operating conditions as part of an in-house production line. The company is now outsourcing its bottling operations, and therefore the machine is available for sale. It is in excellent condition and ready for immediate integration into a new production setup. Technical data  Capacity: approx. 1,200 bottles/hour (in a fully automated line) Cap type: Pilfer proof screw caps Head: Configured for 28 mm caps (interchangeable with other sizes) Bottle compatibility: Adjustable height, currently configured for small bottles Construction: Compact stainless-steel design Condition: Excellent, used for only 1.5 years Operation: Suitable for integration into automated bottling lines  

DESCRIPTION WEILER LZ330 / From Educational Institution -Turning diameter over bed 330mm -Turning diameter over support 165mm -Turning length 800mm -Speed range 25 - 2800 rpm -Automatic / longitudinal plan feeds -Multifix with 3x inserts Hobkn Aujvwctps S Tjl -Drive power 3KW -Three-jaw chuck -Collet device with 20x collets -Copying device -Miscellaneous Accessories -Documentation Dimensions: LxWxH 1.8x0.7x1.6 meters / Weight 750Kg

WEILER Intern 800R Ladder & Pull Spindle Lathe -Turning diameter over bed 300mm -Turning diameter over support 150mm -Turning length 800mm -Spindle bore 42mm -Speed range 40 - 2000 rpm -Automatic longitudinal/plane feeds -Thread/Metric/Inch -Tailstock MK 3 -Drive power 3KW -Multifix with inserts -Three-jaw chuck 160mm -Lining protection -Swarf back wall with work light -Interchangeable wheels -Drill chuck -Rod passage 42mm -Tool cabinet -Documentation Dimensions: LxWxH 1.8x0.8x1.6 meters / Weight 750Kg

GT-5313 1-Spindle Extruder - Brand: PAGANI - Model: 75/ 30D-B - Spindle: Ø 75 mm - With electrical panel - Engine: 103 hp (77 kW) - Year 1995

GT-5315 1-Spindle Extruder - Brand: FLAG - Ø 120 mm - 2.2 meters long spindle - With 75 hp (55 KW) engine - No electrical panel

GT-5343 Single Spindle Co-Extruder - Diameter: 40 mm. - Spindle length of 700 mm - 4 HP (3 kW) geared motor - Electrical panel with variable speed drive

GT-5350 Single Spindle Extruder - Brand: FLAG - Diameter: 120 mm 25 L/D - Spindle length: 3 meters - Extruder electrical panel

GT-5353 Single Spindle Extruder - Brand: FLAG - Diameter: 120 mm 25 L/D - Spindle length: 3 meters - Extruder electrical panel

GT-5354 Single Spindle Extruder - Brand: FLAG - Diameter: 100 mm 25 L/D - Spindle length: 2.5 metres

GT-5355 Single Spindle Extruder - Brand: FLAG - Diameter: 80 mm 25 L/D - Spindle length: 2 meters - Extruder electrical panel

GT-5359 Single Spindle Extruder - Brand: REIFENHAUSER - Type: EH 650-1-90-25 - Diameter: 90mm 25 L/D - Spindle length: 2.4 meters - Extruder electrical panel - No motor

GT-5361 Single Spindle Extruder - Brand: REIFENHAUSER - Type: RH-381-1-70 - Diameter: 70 mm 25 L/D - Spindle length: 1.8 meters - Extruder electrical panel

- Brand: REIFENHAUSER - Type: RH-381-1-70 - Diameter: 70 mm 25 L/D - Spindle length: 1.8 meters - Electrical panel

TECHNICAL SPECIFICATIONS Description: Cement silos / building material silos Number of silos: 3 pcs. Version: 2 x single chamber / 1 x double chamber silo Capacity: 3 x 100 tons. Number of screw conveyors: 4 pcs. SPECIFIC COMMENT - Also available individually - Incl. pneumatic compressed air filling - Incl. dedusting filter