extruder screw barrel used for sale

DRAINING AUGER, construction in aisi 304 stainless steel,, case diameter (U-shape) 380 mm, total length 4.500mm,, internal stainless steel spiral diam. 230mm,, drainage with stainless steel perforated plate L=3.500 mm,, nr.6 hinged side doors,, gear motor power 2.2 kw, installed power - used power in work: about 60-65% : 2.2

pressure: 7 t weight: 0,9 t : 1417 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm

Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)

Key data: 2 mm, 17

Twin screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine No.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. approx. 30 1/min. Worm torque: 10,000 Nm Motor power: 3.3 - 25.0 kW, Drive motor: Commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool Heating Zones: 8 Temperature control: 12 x digital temperature controller KS 40 (PMA) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tools) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material funnel and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hoppe ...

Manufacturer: Cleco / Apex Tool Group Type: TSE 961446PT Voltage: 380 V DC Current: 2-10 A DC Operating temperature: -20 to +70 °C Humidity: 0-90% without condensation You can also find the corresponding screw control in our shop!

Brand: CLECO Series: MPRO400GC Voltage: 230 V AC Frequency: 50/60 Hz Rated current: 2 A Power: Typical 250 VA Degree of protection: IP42

Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm

Stock number: PM2079, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: SMH60 D8

Mounting plate for hammer HM300 with MS03 mount, - Suitable for Hammer HM300, - Recording: MS03, - Hole pattern: 34 x 40 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Stock number: PM2078, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: MH60 D8/B

Toscrew plate for hammer HM100 with MS01 holder, - Suitable for Hammer HM100, - Recording: MS01, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Screw-on plate with Martin M10 mount, - Suitable for demolition & sorting grapples:, - GRP450, - GR45, - GRP750, - GR75, - Mount: Martin M10, - Hole pattern: 36 x 48 cm, - Made of mechanical steel S355, - Dimensions see product pictures, - Immediately available from stock

Toscrew plate for hammer HM100 with MS01 holder, - Suitable for Hammer HM100, - Recording: MS01, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Mounting plate for hammer SB70 with MS01 mount, - Suitable for Hammer SB70, - Recording: MS01, - Hole pattern: 13.5 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Screwing plate / hammer plate / demolition grapple plate / sorting grapple plate suitable for Hammer and Mustang GRP250 and GR25

Screw-on plate with Martin M10 mount, - Suitable for demolition & sorting grapples:, - GRP450, - GR45, - GRP750, - GR75, - Mount: Martin M10, - Hole pattern: 36 x 48 cm, - Made of mechanical steel S355, - Dimensions see product pictures, - Immediately available from stock

Brand Cincinnati Milacron Austria GmbH Type CMT 35 Machine number 2005723/10 Type Screw Conical Double Screw Year of manufacturing 1993 Ble Ud Dvyovl Hzgocop Machine hours 104.599 hours Screw Diameter 35 mm Dimensions (LxWxH) 3200 x 1500 x 1720 mm Weight (approx) 2000 kG

Deze extruder van Cincinnati staat bij Plastima Used Machinery in de machineopslag. De machine komt uit 1999. Speciale opmerking: de extruder mist de versnellingsbak. Bj Usq Tr T Rod Dvycjlp – Merk: Cincinnati – Model: Titan 45R-APC – Bouwjaar: 1998 – Conische dubbele schroef extruder – Schroef Ø: 45 mm – Werkuren: 64.082

Screw Diameter: 35 mm // Output Capacity: 25 kg/h

Screw Diameter: 160 mm // Output Capacity: 1400 kg/h

Screw Diameter: 100 mm // Output Capacity: 600 kg/h

Screw Diameter: 65 mm // Output Capacity: 170 kg/h

Merk: Leistritz AG Model: Micro 27/40 D Type schroef: Dubbele schroef Bouwjaar: 1993 Schroef Ø: 27 mm L/D-verhouding: 40 Werkuren: 2.466 Bws Ud Dvyju Aqdkocjw

Mounting plate for Hammer HM250 with Martin M03 mount, - Suitable for Hammer HM250, - Recording: Martin M03, - Hole pattern: 29 x 29 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

• One pair of original WEBER screws (excellent state, including measurement report • One pair of non-original screws Be Udowaxuae Dvycsww • Gearbox inspected and partially revised by WEBER • Control upgraded to WPS-control • Output on PVC around 700 kg/hour

Mounting plate for Hammer HM250 with Martin M03 mount, - Suitable for Hammer HM250, - Recording: Martin M03, - Hole pattern: 29 x 29 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Brand: Atlas Compo Type: GX5C FF with integrated refrigeration dryer Kind: Screw compressor Serial number: AII642955 Chassis number: 8152101195 Year of construction: 2004 Cooling: Air-cooled Weight: 198kg. Assets: 5.5 kW Sound level: 64 dBA Work pressure: 10 Bar Compressed air: Capacity Approx. 10.0- 10.1 liters/second Length mm: 145cm Width mm: 55cm Height mm: 130cm State machine: Very good Electrical connection: 3 phase Missing parts: No Photos/film available: Photos available 10.2.192

Brand: Boge Type: C3LR Kind: Screw compressor, air-cooled Max. final pressure: 10 bar Chassis number: 5063340 Year of construction: 2013 Capacity: 0.24 m3/min. = 8.3 CFM Engine speed: 1,500/ min. Drive power: 2.2 kW (3 hp) Pressure vessel: 90 liter Voltage: 400V / 50Hz (3-phase) L x W x H: 1185 x 550 x 1010 Noise level: 61 dB (A) Weight: Approx. 130 kg Residual oil content: < 3 mg/m³ Connection: G ½” (ball valve) Cooling air volume: 600 m³/h Ambient temperature range: +5 to +40 °C Photos/film available: Photos available 10.2.195

Mounting plate for Hammer HM250 with Martin M03 mount, - Suitable for Hammer HM250, - Recording: Martin M03, - Hole pattern: 29 x 29 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Mounting plate for hammer HM100 with Martin M03 mount, - Suitable for Hammer HM100, - Recording: Martin M03, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Mounting plate for hammer HM100 with Martin M03 mount, - Suitable for Hammer HM100, - Recording: Martin M03, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Mobile screw compactor Pöttinger BJ 2019

Stationary screw compressor with refrigeration dryer on 500 l container Specifications: Pressure 10 bar Volume flow 2000 l/min Voltage 400 V Drive power 15 kW Beh.-Vol. 500 l Weight 499 kg Noise 65 dB(A) Air outlet 3/4"i Dimensions (WxDxH) 1960x740x1725 mm Hint: ! without TÜV approval, container papers are not available

General SKU392U1285 LocationBarneveld MakeK-tron / Burgener TypeK-PH-MV-KT20 / AFS002 No.1102400/M-984900 Main Features MaterialStainless steel Motor0.75 KW Inlet diameter200 mm Specified Features - Metering screw MaterialStainless steel 1.4401 (316), Stainless steel 1.4404 Metering screws Metering screwcheck Screw diameter± 25 mm (2x) Pitch± 10 mm Screw length300 mm With hoppercheck Hopper sizesdia. 200x220 mm Inletdia. 200 mm OutletDN40 With motor0,75 kW Screw speedmax. ± 460 rpm: With breaking/mixing shaftcheck (max. ± 21 rpm) Motor0,75 kW Information Year of construction2011 Mounted on framecheck Mounted on legscheck Mounted on wheelscheck CEcheck With switchgearcheck Floorspace1,4x0,8 m Total height2,4 m ATEX compatiblecheck Extra SpecificationsThe filling plant allows for the semi-automatic filling of biologically highly active, hygroscopic,  ...

General SKUR1412 LocationBarneveld MakeFrewitt TypeProFi-Dos, ProFi-Sword No.5921810811 Main Features MaterialStainless steel Motor0.37 KW Inlet diameter260 mm Specified Features - Metering screw MaterialStainless steel 1.4404, Stainless steel 1.4435 (316L) Metering screws With hoppercheck Capacity120 Ltr. Hopper sizesdia. 600x800 mm Inletdia. 260 mm Outletdia. 300 mm With breaking/mixing shaft16 rpm Motor0,37 kW 230 Volt Information Year of construction2007 Floorspace0,9x1 m CEcheck Weight250 kg Extra SpecificationsSurface quality: Ra≤0.8 μm The ProFi-Sword module is a discharge system which fluidzes powder, providing good flow behavior and preventing bridge formation. : Metering screwsFrewitt FribourgDosing units > Metering screwsBrand > Frewitt Fribourg What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to ne ...

Key data: 72 mm

We can offer a W&P extruder. 75/36, year 2004, stopped, working condition.

Key data: 58 mm

We can offer a Toshiba extruder. 58/40, year 2010, stopped, working condition.

Offer 25432 Specifications: - Turning diameter 320 mm - Center width 750 mm - Largest turn – Ø over bed 550 mm - via flat slide 175 mm - Spindle bore 32 mm - Spindle holder - Pick-up cone of the tailstock quill MK 3 - Quill stroke 180 mm - 18 spindle speeds 85 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches -Thread - Module thread - Diametrical Pitsch thread -Arbor - Cheek chuck -Lunette - Drive 400 V / 2.2 kW - Space requirement approx. W 2100 x D 750 x H 1300 mm - Weight approx. 750 kg

Manufacturer: Optimum Year of construction: 2024 Condition: as good as new, workshop tested Delivery time: immediately available Specifications Tip height: 165 mm Center width: 830 mm Circumferential diameter over bed: 330 mm Circumferential diameter over face slide: 208 mm Swivel length in the bed bridge: 430 mm Speed ranges: 16 steps, 70–2000 rpm⁻¹ Drive motor: 1.5 kW, 400 V, 50 Hz Spindle holder: Camlock DIN ISO 702-2 No.4 Spindle bore: 38 mm Spindle cone: MK5 Tailstock mount: MK3, quill stroke 110 mm Weight: approx. 512 kg Machine dimensions (LxWxH): 1685 × 745 × 1590 mm Gradients and feed Metric: 0.4-7 mm/rev (26 pitches) Inches: 56-4 Gg/1" (34 pitches) Longitudinal feed: 0.052–1.392 mm/rev (32 feeds) Face feed: 0.014–0.38 mm/rev (32 feeds) Accessories: Fixed bezel (Ø 6–50 mm) Rotating bezel (Ø 8–3 ...

Weiler Commodor – lead and pull spindle lathe (partially overhauled, built approx. 1990) Condition: Partially overhauled, very good general condition Year of construction: approx. 1990 Manufacturer: Weiler Model No.: Commodor Machine Type: Lead and Pull Spindle Lathe Technical data (approx. information): Max. turning diameter over bed: 380 mm Max. turning diameter over support: 190 mm Max. turning length: 1000 mm Bar Passage: 56 mm Speed range: 25 – 2000 rpm Spindle Nose: A2-6 Drive power: 4.0 kW Tailstock: MK4 Automatic longitudinal and flat feeds: 0.011 – 0.80 mm/rev Thread ranges: Metric: 0.3 – 10 mm Inch: 80 – 2 3/4 G/" Diametrically Pitch: 80 – 5.5 Dp Module: 0.2 – 5 Dimensions (L x W x H): 2200 × 1200 × 1800 mm Weight: approx. 1500 kg ⚙️ Equipment & Accessories: 3-Axis Digital Display SINO (New)  ...

MD-0105 Twin Screw Extruder - Brand: MAPRE - Type: E.2.6.100.22 - Diameter: 100 - Uses 22 L/D - With dispenser - 74 KW motor - Variable speed drive - Electrical panel - With hopper with forced feeder

TOS Galanta SUIL 40A – Lead and Pull Spindle Lathe For sale is a well-preserved and mechanically overhauled 2009 TOS Galanta SUIL 40A lead and pull spindle lathe, built in 1998. Specifications Manufacturer: TOS Model: Galanta SUIL 40A Machine number: 0219 Year of manufacture: 1998 (mechanically overhauled 2009) Dimensions: approx. 2.2 m × 1.1 m × 1.75 m Weight: 1620 kg Main drive: 5.5 kW Spindle speed (max.): 3150 rpm Spindle bore: 50.2 mm Center spacing: 1000 mm Center height: 200 mm Turning diameter over bed: 400 mm Condition: ready for use (used) Accessories Three-jaw chuck Tailstock Lunette Coolant Setup Interchangeable Wheel Set Operating instructions (German) The machine is fully functional. Viewing possible by appointment

Key data: 22 mm, 60

Single screw extruder 60 with renewed PMA control in 2010 - was replaced by double screw 5 years ago. Works after oil and belt change

feed pressure: 8,5 bar liter capacity: . l total power requirement: 454 kW weight of the machine ca.: t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ALMIG Combi 15-10 rotary screw air compressor YOM 2012. Never used. Motor speed 3000 rpm Motor power 15 kW Volume flow m3/min- 1.84 Volume m3/hour- 110 Max. pressure 10 Bar. Air Receiver Capacity 500L

Digital Center height 150 mm Circulation over bed 300 mm Center width 1000 mm 3-jaw chuck, Arbor Chip protection Chip tray

Motor power: 45 kW Nominal flow rate: 7.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1500x1000x1265 mm Estimated weight: about 700 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-4

A screw compressor is offered. Maximum pressure 10bar, volume flow approx. 2020l/min (2.02m3/min) with separate compressed air tank, galvanized. Viewing possible by appointment.

Motor power: 11 kW Nominal flow rate: 1.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-2