british flag
Resale Logo

engine used machine for sale on RESALE.INFO
all categories

back back
 banner advertisement information warehouse systems  LHS Vertriebsgesellschaft mbH  http://www.lhs-online.com 
banner logo
start page > keywords engine > results
maximum number of results exceeded > 1000
please refine your search
1000 items ordered by
post used machinery     
No. Cat. Photo Manufacturer | Model
Type of machinery
Year Price Country Contact
 page 1  > 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
125517864 702

MEILI 200 for sale
double Z Kneader / Sigma Kneader


Many thanks for your interest in our second-hand machinery, please find below our offer: manufacturer: Fritz Meili Type: 200 Doppel-Z-Kneter pott dimensions: 600x600x500mm Contents: 150-180 L (usable) Enginepowe ...

 
Many thanks for your interest in our second-hand machinery, please find below our offer:
manufacturer: Fritz Meili
Type: 200 Doppel-Z-Kneter
pott dimensions: 600x600x500mm
Contents: 150-180 L (usable)
Enginepower: 7,5 KW
dimensions: ca. 2000x1300 x 1600mm
weight: ca. 2000 kg
different: product touching parts in SS
protective grille and lid
hydraulic tiltable
partially NEW electric (new cabinet with contactors)
hydr. Engine NEW
main Engine repaired

We offer this machine in 'as is' condition, without warranty

ex Warehouse Hess. Lichtenau, unpacked

 
Price  
    request
125516711 1101

Alsthom UTE C52 100 - Transformer - DPX-11375 for sale
Diesel Generators


; Engine: Alsthom
used machine
 
; Engine: Alsthom
1989
4,250 €  
  NL   request
125517862 1103  

BBC VTR 354-11 2P for sale
TURBOCHARGER


FOR SALE USED BBC VTR 2 354-11 P INLET COMPLETE TURBO CHARGER TO WHOM IT MAY CONCERN; WE VE COMPLETE USED BBC VTR 2 354-11 P AT OUR STOCK. TURBO DISMANTLED FROM MAK 8M 32 ENGINE ENGINE kW 4011 PLS FIND T ...

 
FOR SALE USED BBC VTR 2 354-11 P INLET COMPLETE TURBO CHARGER



TO WHOM IT MAY CONCERN;

WE VE COMPLETE USED BBC VTR 2 354-11 P AT OUR STOCK.

TURBO DISMANTLED FROM MAK 8M 32 ENGINE ENGINE kW 4011

PLS FIND T/C AT SPEC BELOW

BBC VTR 2 354-11 P

2 INLET

HT 371508
V0111 3R011 H01111
W121 08E 03321 L181

CASING AA21

TURBO CHARGER IN GOOD WORKING CONDATION TURBO CHARGER READY TO TRANSPORT AT IZMIR TURKEY

IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US.




Capt. Ayhan Ugurluba

Best regards;

Aliaga marine services
E mail: info/aliagamarine.com
PHN/fax: +90 232 618 03 90
Mobile: + 905556084850
aliagamarine.com
TURKEY
 
Price  
    request
125515946 1005

IVECO MTD.CNM.350 Generator 500kVA With Hot Water Boiler for sale
All terrain cranes


; Power [PS]: 475; Gross weight [kg]: 18000; Engine: Iveco; Accessories: Generator 500kVA With Hot Water Boiler, , MHKW Systems., , Manufacturer Engine: Iveco, Typ Engine: MTD, CNM, 350, Manufacturer Generator: AVK, Typ  ...
used machine
 
; Power [PS]: 475; Gross weight [kg]: 18000; Engine: Iveco; Accessories: Generator 500kVA With Hot Water Boiler, , MHKW Systems., , Manufacturer Engine: Iveco, Typ Engine: MTD, CNM, 350, Manufacturer Generator: AVK, Typ Generator: DSG52M1.4, Year: 1994, Fuel: Diesel, Serial Number Engine: 000173, Serial Number Generator: 66162
1994
11,900 €  
  NL   request
125479994 104

LINDNER GL4 / 4000 for sale
Thread Grinding machine


Feed speed: 45 m/s Workpiece rotation: 40 rpm Workpiece diameter: 500 mm Grinding length: 4000 mm Clamping length: 4170 mm Wheel diameter: 700 mm Wheel width: 60 mm Engine power:10 kW Machine weight: 1900 ...
used machine
 
Feed speed: 45 m/s
Workpiece rotation: 40 rpm
Workpiece diameter: 500 mm
Grinding length: 4000 mm
Clamping length: 4170 mm
Wheel diameter: 700 mm
Wheel width: 60 mm
Engine power:10 kW
Machine weight: 19000 kg
Accessories:
Steady rests
Set of gears
1961
Price  
    request
125513984 1010

DYNAPAC CH-45 for sale
Wheel loaders


; Power [PS]: 38; Gross weight [kg]: 5000; Engine: Deutz F3L/912
used machine
 
; Power [PS]: 38; Gross weight [kg]: 5000; Engine: Deutz F3L/912
1974
Price  
  AT   request
125479945 1101

PERKINS 2306 - 365 KVA for sale
Diesel generators


used machine
 
2008
Price  
  BE   request
125514240 1006  

BOMAG BPR 50/55 D/E for sale
Graders


386 kg; Power [PS]: 8; Gross weight [kg]: 386; Engine: Hatz 1B40
used machine
 
386 kg; Power [PS]: 8; Gross weight [kg]: 386; Engine: Hatz 1B40
2016
Price  
  AT   request
125479941 1101

IVECO V8 - 500 KVA for sale
Diesel generators


used machine
 
2004
Price  
  BE   request
125513986 1010

RAMMAX RW 1504 for sale
Wheel loaders


1,5 to.,; Power [PS]: 17; Gross weight [kg]: 1480; Engine: Hatz 2 G 40
used machine
 
1,5 to.,; Power [PS]: 17; Gross weight [kg]: 1480; Engine: Hatz 2 G 40
2008
Price  
  AT   request
125479936 106

SCHULER PSt 250-10-400 for sale
Mechanical Presses


Press Schuler PSt 250-10-400 The machine is in good technical condition. Crimping force: 250t Number of Instrument Stations: 8 + 1 Band width: 630mm Band feed: 0-630mm Sheet thickness: max. 4mm Bearing weight: 450 ...

 
Press Schuler PSt 250-10-400
The machine is in good technical condition.
Crimping force: 250t
Number of Instrument Stations: 8 + 1
Band width: 630mm
Band feed: 0-630mm
Sheet thickness: max. 4mm
Bearing weight: 4500kg
External diameter max. 1200mm
Internal diameter from-to: 410-480mm
Engine 60kW
Dimensions of the press: 6225 x 3100 x 8425 mm
Including unwinding and straightening equipment and transfer.
Upon agreement, possible to test.
 
Price  
  SK   request
125514242 1006

BOMAG BPR 50/55 DE for sale
Graders


; Power [PS]: 8; Gross weight [kg]: 405; Engine: Hatz 1B40
used machine
 
; Power [PS]: 8; Gross weight [kg]: 405; Engine: Hatz 1B40
2017
Price  
  AT   request
125479923 102

WEILER COMMODOR for sale
Engine Lathes (Sliding, Surfacing And Screw Cutting Lathes)


L + Z lathe hamlet can 04-03-222 delivery time: immediate number: 04-03-222 manufacturer: Weiler type: can MACHINE data built: approx 1980 L x W x H: approx. 2700 x 1200 x 1800 mm weight: approximately 1500 kg Ver ...
used machine
 
L + Z lathe hamlet can 04-03-222 delivery time: immediate number: 04-03-222 manufacturer: Weiler type: can

MACHINE data built: approx 1980 L x W x H: approx. 2700 x 1200 x 1800 mm weight: approximately 1500 kg

Very good condition - from stately authority technical data digital display: 3 - axes - digital display (new) dimensions: Max turning diameter over bed: approx. Ã? 380 mm max turning diameter over support: approx. Ã? 190 mm maximum turning length: approx. 1000 mm Stangendurc "hlass: approx. Ã? 56 mm spindle: speed range: approx. 25-2000 RPM spindle nose: A 2 - 6 power: approx. 4,0 kW automatic longitudinal & plan vorschuebe: feed range: 0,026-1,253 mm / U suitable for threads: - metric 0.35 - 12 mm - inch 44-2 Gg /"

-Diametral - Pitch threaded 88 - 5 DP - module 0.2 - 4 live: MK 4 Accessories â?¢ 3 - bake - chuck Ã? 200 mm Röhm â?¢ quick change Toolpost + 3 inserts â?¢ bed fence â?¢ complete machine documentation â?¢ various wrenches â?¢ feet â?¢ cow lmitteleinrichtung other accessories on request price and other specifications on request
1980
Price  
    request
125513988 1010  

WACKER DPS 1850 Hv for sale
Wheel loaders


116 kg; Power [PS]: 4; Gross weight [kg]: 116; Engine: Hatz 1B20
used machine
 
116 kg; Power [PS]: 4; Gross weight [kg]: 116; Engine: Hatz 1B20
2016
Price  
  AT   request
125479919 102

WEILER PRAKTIKANT 160 B for sale
Engine Lathes (Sliding, Surfacing And Screw Cutting Lathes)


L + Z lathe hamlet intern 160 B - 04-03-221 delivery: immediately number: 04-03-221 manufacturer: Weiler type: intern 160 B MACHINE data year: approx. 1991 L x W x H: approx. 1700 x 1000 x 1700 mm weight: approx. 650 ...
used machine
 
L + Z lathe hamlet intern 160 B - 04-03-221 delivery: immediately number: 04-03-221 manufacturer: Weiler type: intern 160 B

MACHINE data year: approx. 1991 L x W x H: approx. 1700 x 1000 x 1700 mm weight: approx. 650 kg

Very good condition specifications digital display: 3 - axes - digital display safety dimensions: Max turning diameter over bed: approx. Ã? 320 mm maximum turning diameter over support: approx. Ã? 198 mm maximum turning length: approx. 650 mm bar passage: approx. Ã? 40 mm SPI Handel: speed range: approx. 96-2500 RPM spindle nose: A 2 - 5 power: approx. 2.2 kW automatic longitudinal & plan vorschuebe: feed range: approx. 0.007 - 0.63 mm / Rev suitable for threaded: - metric 0.25 - 8 mm - inch 80-2 Gg / "- Diametral - Pitch thread" 200-5 DP - module 0.2-4 live: MK 3 accessories â?¢ 4 - bake - chuck Ã? 160 Röhm â?¢ hand tension - tension clamp Assembly 386E â?¢ various collets 386E â?¢ quick change Toolpost + 3 inserts â?¢ work light â?¢ coolant system â?¢ complete MASC hinendokumentation â?¢ emergency â?¢ drill Chuck for tailstock â?¢ revolving tailstock tip â?¢ various wrenches â?¢ L + Z spindle - cover

Accessories on request price and other specifications on request
1991
Price  
    request
125514244 1006

BOMAG BPR 60/65 D for sale
Graders


; Power [PS]: 8; Gross weight [kg]: 457; Engine: HATZ 1B40
used machine
 
; Power [PS]: 8; Gross weight [kg]: 457; Engine: HATZ 1B40
2015
Price  
  AT   request
125479917 102

WEILER CONDOR VS for sale
Engine Lathes (Sliding, Surfacing And Screw Cutting Lathes)


L + Z lathe WEILER CONDOR VS 04-03-220 delivery: immediately number: 04-03-220 manufacturer: Weiler type: Condor VS MACHINE data year: approximately 1978 L x W x H: approx. 1600 x 1000 x 1800 mm weight: 800 kg Goo ...
used machine
 
L + Z lathe WEILER CONDOR VS 04-03-220 delivery: immediately number: 04-03-220 manufacturer: Weiler type: Condor VS

MACHINE data year: approximately 1978 L x W x H: approx. 1600 x 1000 x 1800 mm weight: 800 kg

Good general condition specifications digital display (optional): 2 or 3 - axes - digital display new dimensions: Max turning diameter over bed: approx. Ã? 320 mm maximum turning diameter over support: approx. Ã? 160 mm maximum turning length: approx. 800 mm bar passage: approx. Ã? 38 mm spindle: speed range: approx. 12-2800 RPM spindle nose: A 2 - 5 power: approx. 3.8 kW automatic longitudinal & plan vorschuebe: feed range: 0.037 1,253 mm / U suitable for threads: - metric 0.35 - 12 mm - inch 50-1.5 Gg / "- diametrically opposed" -Pitch thread 100 - 4 DP - module 0.2 - 6 live: MK 3 accessories â?¢ 3 - bake - chuck Ã? 160 mm â?¢ quick - clamping Collet device (prepared) â?¢ quick change Toolpost + 2 Inserts â?¢ complete machine documentation â?¢ emergency - off â?¢ various length chlüssel â?¢ bed fence â?¢ coolant system â?¢ various change gears

Accessories on request price and other specifications on request
1978
Price  
    request
125514246 1006

BOMAG BPR 60/65 D for sale
Graders


455 kg; Power [PS]: 8; Gross weight [kg]: 455; Engine: Hatz 1B40
used machine
 
455 kg; Power [PS]: 8; Gross weight [kg]: 455; Engine: Hatz 1B40
2015
Price  
  AT   request
125479914 102

WEILER MATADOR VS TEILÜBERHOLT for sale
Engine Lathes (Sliding, Surfacing And Screw Cutting Lathes)


L + Z lathe WEILER MATADOR VS without -04-03-217 delivery: upon request number: 04-03-217 manufacturer: Weiler type: Matador VS without . MACHINE data built: approx 1980 L x W x H: 1500 x 800 x 1500 mm weight: appr ...
used machine
 
L + Z lathe WEILER MATADOR VS without -04-03-217 delivery: upon request number: 04-03-217 manufacturer: Weiler type: Matador VS without .

MACHINE data built: approx 1980 L x W x H: 1500 x 800 x 1500 mm weight: approx. 550 kg

Very good condition - without - picture similar

(Click on without to see the extent of the overhaul)

TECHNICAL data digital display: 3 - axes - digital display new dimensions: Max turning diameter over bed: approx. Ã? 280 mm max turning diameter over support: approx. Ã? 160 mm maximum turning length: approx. 500 mm bar passage: approx. Ã? 36 mm spindle: speed range: CA. 15 -. 3550 RPM spindle nose: A 2 - 5 power: approx. 3.0 kW automatic longitudinal & plan vorschuebe: feed range: approx. 0.05 - 0.80 mm / U suitable for threaded: - metric 0.2 - 12 mm - inch 80-2 Gg / "- Diametral - Pitch threaded 160-6 DP - module 0.1-4"

Tailstock: MK 3 accessories â?¢ 3 - bake - chuck Ã? 160 mm new â?¢ quick change Toolpost + 3 inserts â?¢ electric Chuck guard â?¢ work light â?¢ coolant system â?¢ complete machine documentation â?¢ emergency - off â?¢ drill Chuck for tailstock new â?¢ with ongoing tip for tailstock new â?¢ various wrenches â?¢ feet â?¢ leit & spindle - cover (optional) â?¢ motor with motor brake (option) â?¢ clamping Collet device (option)

Accessories on request price and other specifications on request
1980
Price  
    request
125514248 1006  

BOMAG BPR 35/60 DE for sale
Graders


245 kg; Power [PS]: 4; Gross weight [kg]: 245; Engine: Hatz 1B 20
used machine
 
245 kg; Power [PS]: 4; Gross weight [kg]: 245; Engine: Hatz 1B 20
2017
Price  
  AT   request
 page 1  >
You didn't find your wanted machine?   to all dealers(no registration necessary)
More models (2 or more machines):
(17)
sell machinery
Sell your machinery
to the price starting with only € 0.09 monthly per machine!
machinery sold

Sold machinery

Gas engines MAN E 2876 LE 202


Power: 220 kW Rotation speed: 1500 1/min. Suitable generator, gas control line, exhaust heat exchanger and value heat exchanger available, price on request.

Gas engines MAN E 0836 LE 202


Power: 110 kW Rotation speed: 1500 1/min Suitable generator, gas control line, exhaust heat exchanger and value heat exchanger available, price on request.

Smoke chamber Vemag 2 trolleys


Condition: Overhauled Technical data: • overall dimensions 1600x2500x2900 mm; • 2 trolleys 1000x1000x2000 mm; • power heating 52 kW; • power supply 400 V; • computer control Mikster; • smoke generator Fessmann RZ550 115; • smoke generator dimensions 550x1200x1580 mm; • power engine 0.7 kW; • power heating 1.0 kW.

Diesel engines MWM DEUTZ TBD620V12


2 COGENERATION ENGINES: 2 X MWM-DEUTZ V12 TBD620 YEAR OF MANUFACTURE: 1999 HOURS: approx. 9000 OUTPUT: 1.3Mw ALTERNATOR: LEROY SOMER OUTPUT: 1260 KW / kVA 1300 COMPLETE PLANT •Generator (alternator, engine engine and PLC) •Gas train •Water cooling system (heat exchanger + complete pump) •Oil Cooling System (heat exchanger + complete pump) •Control Panels generator (DIANE) •Electrical control panel accessories (pumps, etc) •Technical Documentation

Casting press URPEMAK URPE CFA 220


Foundry machine URPE URPEMAK CFA 220 produced in 2005 year in Spain. The price of the machine the crucible for melt aluminum, with a capacity of approx. 500 l, visible on the last photo. Injection molding machine for aluminium URPEMAK URPE CFA 220-technical parameters: -clamping force: 2250 kN -Road: 440 mm -the strength of the ejector: 120 kN -ejector stroke: 100 mm -height (min-max): 240/600 mm -dimensions: 780 x 780 mm -distance between columns: 510 x 510 mm -diameter: 90 mm -the position of the injection: 0-90-180 mm -the maximum force-cast: 121-250 kN -piston injection: 40-50-60-70 mm -feed cast: 360 mm -the surface of the casting: 113-714 cm2 the mass/volume of injection: 301-471-678-923 cm3 -injection pressure: 315-1990 daN/cm2 -engine: 20 kW -weight: 13000 kg -dimensions: ok. 590 x 238 x 275 cm

Casting press URPEMAK URPE CFA 330


Injection molding machine for aluminium URPEMAK URPE CFA 330 manufactured in 2008 year in Spain. The price of the machine is the crucible to melt zinc, with a capacity of approx. 400 l, visible on the last photo. Foundry machine URPE URPEMAK CFA 330-technical data: -clamping force: 3300 kN -road closure: 510 mm -the strength of the ejector: 181 kN -ejector stroke: 120 mm -height (min-max): 300/700 mm -dimensions: 910 x 910 mm -distance between columns: 572 x 572 mm -diameter: 115 mm -the position of the injection: 0-80-160 mm -the maximum force-cast: 155-350 kN -piston injection: 50-60-70-80 mm -feed cast: 445 mm -the surface of the casting: 170-1089 cm2 the mass/volume of injection: 655-943-1294-1677 cm3 -injection pressure: 308-1782 daN/cm2 -engine: 33 kW -weight: 16000 kg -machine dimensions: 700 x 270 x 290 cm

Circular press FPA PXW 100 AAb


Press obwiedniowa of varying matrix FPA PXW 100 AAb was built by the factory Automatic Presses Warsaw, Poland-Italy. FPA press-specific data PXW 100 AAb: largest diameter: 100 mm -pressure: 160 T -stroke: 140 mm -the amount of fluctuation matrix: 1500 l/min. -engine power: 17 kW -the engine speed: 3000 l/min. -pump motor power: 11 kW -the engine speed pump drive: 1000 l/min. -the power of pump motor battery: 0.8 kW -the engine speed pump battery: 1500 l/min. -weight of the machine: 53000 kg

Guillotine Shears STROJARNE PIESOK NTC 2000/4


Guillotine STROJARNE PIESOK NTC 2000/4 were produced in 1987. Shears allow cutting of materials with different strength such as steel, aluminium, copper, etc. The materials with a tensile strength of more than 450 MPa cut material thickness must be correspondingly reduced. In the case of less strength than the 450 MPa can cut materials with a greater thickness, which the breakdown does not exceed 8 mm. The thickness of the material to be cut, depending on the strength of: aluminum 200 MPa: 6 mm copper 250 MPa: 5.3 mm nickel 400 MPa: 4.2 mm steel 450 MPa: 4 mm steel 500 MPa: 3.8 mm brass 600 MPa: 3.4 mm steel 700 MPa: 3.2 mm steel 800 MPa: 3 mm Technical parameters of the guillotine NTC 2000/4: -maximum thickness sheet with pt = 450 MPa: 4 mm -maximum cutting length: 2050 mm -cutting angle: 1.33 degree -outreach in the stands: 200 mm -number of jumps continuous operation at idling speed: 60 RPM -the minimum thickness of the metal: 0.4 mm -the minimum width of the webs: 10s mm (s-thickness) -the maximum radius of curvature of the knife: 0, 05s mm (s-thickness) -cut on the rear bumper, the maximum width without brackets: 300s mm (s-thickness) -position the rear bumper: 4-750 mm -installed power: 5 kVA -the power of main motor: 4 kW -engine power bumper: 0.25 kW -overall dimensions of the device (l x w x h): 2600 x 1600 x 1500 mm -Cutter weight: 3400 kg -foot pedal -DTR, a technical-functional

Wheel loaders HSW 515 G


Loader HSW 515 G was built by Ironworks Stalowa Wola in 2009 year. HSW-specific data 515 G: -mileage: 30.000 mTh (hours) -engine: Cummins-after overhaul -weight-tires Good Year RL-5 k

CNC Long Turning Automatics POLYGIM DIAMOND 32 CSB SWISS TYPE


Automatic longitudinal turning Swiss POLYGIM DIAMOND CSB 32 SWISS TYPE was built in 2008. Technical data for CNC lathes POLYGIM DIAMOND CSB 32 SWISS TYPE: CNC Control: MITSUBISHI Working range: -maximum turning diameter: fi 33 mm -maximum turning length: 250 mm -the maximum diameter of drilling: fi 15 mm -the maximum diameter of the thread: M10 Processing of external diameters: -quantity: 5 PCs. -dimension of the CAP: 16 x 16 x 120 mm Treatment of internal diameter: -quantity: 4 PCs. -Sleeve dimension: 13 mm (ER20) Transverse driven tool:-number of tools: 3 PCs. -Sleeve dimension: 13 mm (ER20) -speed: 200-6000 RPM. Tools from the back to the internal diameter: -quantity: 4 PCs. -Sleeve dimension: 13 mm (ER20) Tool driven to face: -number of tools: 3 front, 3 rear -Sleeve dimension: 10 mm (ER16) -speed: 3000 rpm. Main spindle:-spindle bore diameter: fi 36 mm -spindle speed: 200-8000 RPM. -Spindle bore diameter: subspindle steals: fi 36 mm -spindle speed steals: 6000 RPM. -the maximum spindle stroke: 220 mm rapid feeds X, Y, Z: 18 m/min. Engines: -spindle motor: 5.5 kW -spindle motor steals: 1.5 kW -drive motors. X/Y/Z axis: 0.5 kW -Coolant pump motor: 0.55 kW -lubrication: 4 -power supply: 8.67 kW -the spindle axis height: 960 mm Machine dimensions:-overall dimensions: 2550 x 1140 x 1568 mm -weight: 2788 kg Compressed air supply: -Outlook: 10 l/min. -pressure: 5 kg/cm Equipment: -subspindle -lighting of the workspace -cooling system -orientation of przeciwwrzeciona every 5 degrees -sensor cut off part-receiver detail -Guide ring Rod fixed and Rotary -5 pieces of the outer surface of the turning handles -4 desktop holders for turning the inner surface of the -4-position for desktop tools for turning the inner surface of the rear -6-powered tool for working the transverse -3 to-powered tool to work from the front -3 to-powered tool to work from behind -automatic bar feeder: Fedek SUNNY 542 (3.2 m) -chip conveyor

Shredder DOPPSTADT AK-430 PROFI


Motor: MERCEDES BENZ diesel engine OM 501 LA, mallet drum dimensions: 1750x1100mm, rotational speed: 850-1000/min, number of mallets: 36, mallet weight: 14.5kg, max. inlet height: 650mm, outlet conveyor dimensions: 4000x1800mm, conveyor speed: 2.25m/s, ejector height: 3000mm, length: 11630mm, width: 2500mm, height: 3000mm.

Radial Drilling Machines Z 3050 X 16


Radial drilling machine with 3050 X 16 was built in 1989. This versatile general-purpose machine. It is suitable for drilling, countersinking, reaming, chamfering and thread cutting medium and large items. With the right equipment it is also possible to boring. Technical data drilling machine Z3050 X 16: -the maximum drilling diameter: 50 mm maximum range: 1600 mm -the maximum distance between the axis of the spindle and the column: 1600 mm -the minimum distance between the spindle axis and column: 350 mm -horizontal spindle head on your shoulder: 1250 mm -maximum distance from spindle face to the working surface of the base plate: 1220 mm (1250 mm) -minimum distance from spindle to base plate working surface: 320 mm (350 mm) -vertical stroke in column: 580 mm -arm lifting speed: 0.02 m/sec. -angle of rotation of the arm: 360 degrees -taper in the spindle: Morsea Nr. 5 -spindle speed range: 25-2000 RPM. -number of spindle speeds: 16 PCs. -feed range: 0.04-3.2 mm/Rev. -the amount of feeds: 16 PCs. -extension: 315 mm -depth of feed per rotation of graduated: 122.5 mm -maximum permitted torque on the spindle: 490 Nm -maximum permitted weight spindle: 15680 N -the power of main motor: 4 kW -engine power lifting arm: 1.5 kW -engine power the hydraulic lock: 0.75 kW -Coolant pump motor power: 0.09 kW -overall dimensions (l x w x h): 2500 x 1060 x 2655 mm -weight of the machine: ok. 3500 kg (3900 kg with a column guide)

Dishwashers Pebock UGD-25


Description Mark PEBOCK UGD model-25 ID 30122/142 Status Active €1,500 price + VAT Year 2008 Location Of Oradea (RO) Washing machine UGD-25 Pebock shuttles from 2008 in damage, with the engines. The electronic system is complete. ExWorks. Price is negotiable and do not include VAT. Contact Tel.: + 359/40-175.575 Fax: + 40-259/426.248 Mobile: + 40-743/177.040; + 40-740/221.698 Watching the product schedule 24 hours prior. We speak English. WIR sprechen Deutsch. (+ 40-740/221.698) Hablamos Español. Beszélünk magyarul. (+ 40 743/177.040) Irrtum und Zwischenverkauf vorbehalten, Anderungen/ Subject to errors, changes and prior to his/ We reserve the right to mistakes, changes and prior sale.

Double screw-type extruding machine FANGTAI FT 500-2


Twin-screw FANGTAI FT 500-2 produced in 1998 year. The machine has one screw diameter fi 50 mm and one snail with a diameter of 65 mm. Technical parameters of the machine screw diameter fi 50 mm: -screw diameter: fi 50 mm -L/D ratio of length to diameter of the cochlea: 28:1 -screw speed: 10-120 RPM -foil width: 200-550 mm -film thickness: 0.015-0.04 mm -main engine power: 7.5 kw -heating power: 30 kw -capacity: 50-100 kg/h. -weight: 2.8 t -dimensions (l x w x h): 5600 x 2600 x 1800 mm3 Technical parameters of the machine screw diameter fi 65 mm: -screw diameter: fi 65 mm -L/D ratio of length to diameter of the cochlea: 30:1 -screw speed: 10-120 RPM -foil width: 200-650 mm -film thickness: 0.015-0.04 mm -main engine power: 15 kw -heating power: 30 kw -capacity: 50-100 kg/h. -weight: 3 t -dimensions (l x w x h): 6000 x 1500 x 2500 mm3

Eccentric Presses TOMA LEN 63C


Eccentric press TOM LEN 63 c was produced in 2012. The machine allows to realize punching, cutting and punching. The press can work with different instruments. It is also possible to full automation of the work by arming its tape dispenser. Technical parameters of the presses LEN 63 C: -clamping force: 63 tons -table size: 800 x 630 mm -the surface of the slider: 450 x 280 mm -outreach: 315 mm -the number of jumps in: 65/130 min. -number of jumping manual work: 45/50 min. -adjust the pitch slider: 10-105 mm -the self-alignment capacity of slider: 70 mm -ground clearance table-slider: 335 mm -the ground clearance between columns: 355 mm -quantity: 2 -engine: 730/1440 min. -engine power: 4/7.5 kW -overall dimensions: 1425 x 1790 x 2550 mm -weight of the machine: 5850 kg Advantages of the press TOM LEN 63 C: -die-cast housing: grey cast iron -the possibility of setting the size of the pitch slider -the possibility of repositioning the slider -pneumatic balancing slider -accurate, extended, self-lubricating guiding slider -eccentric shaft fit rolling rod -molded friction clutch: brake, meeting the requirements of the provisions of safety at work

Heavy Lathes POREBA TCA 160


Heavy lathe POREBA TCA 160 was produced in 1959 by the famous Polish FUM POREBA. Technical data of lathe POREBA TCA 160: Scope of work:-height of tusks: 800 mm -maximum turning diameter over bed: 1600 mm -maximum turning diameter over support: 1300 mm -eyepiece: fi 800 mm -maximum turning diameter in the pó?okularze: 250 mm -maximum turning length: 6000 mm -maximum weight of workpiece between centers in: 16000 kG -permissible cross section of the chip (turning steel Rr = 60 kG/mm2) on a single support: 30 mm2 -permissible cross section of the chip (turning steel Rr = 60 kG/mm2) on a single support: 50 mm2 -permissible force on the knife: 6000 kG -the maximum torque at the spindle: 630000 kg.cm -the maximum cross section 70 x 70 mm knife: Cap Headstock: -number of spindle speeds: 24 n -the exponent of the speed: 1.25 -spindle speed range: 1,12-224 RPM., 1,12-224 r/min, 0.85-170 RPM. -front spindle neck diameter: 260 mm -slot in the spindle of the cone metric: # 120 -reducing Bush metric cone Tip: # 120/80 -spindle bore diameter: 105 mm -diameter of the blade Cap: 1600 mm Suport, feeds the normal: -20 longitudinal feed range: 0,19-5,0 mm/Rev. -20 transverse feed range: 0,095-2.5 mm/Rev. -20 feed on the upper tray of the range: 0,095-2.5 mm/Rev. Suport, feeds 8-20 longitudinal feed range: 1.5-40 mm/Rev. -20 transverse feed range: 0.75-20.0 mm/Rev. -20 feed on the upper tray of the range: 0.75-20.0 mm/Rev. Suport, feeds minute:-20 longitudinal feed range: 12-320 mm/Rev. -20 transverse feed range: 6-160 mm/Rev. -20 feed on the upper tray with a range: 6-160 mm/Rev. Suport, feeds to thread (the main screws. train.):-35 thread jumping metrycz. about t. : 1-50 mm -jumping 35 inch threads range: 24-1/2 scroll/inch Suport, feeds for threading on the top tray:-25 thread jumping metrycz. about t. 0.25-7 mm -jumping 35 inch threads/inch scroll: the scroll 28-3/inch Feed rates associated to the rolling cones of gradients creating: 1:1.5 (d) 1:1000 -rapid traverse: 4000 mm/min. Konik: -barrel diameter: 200 mm -stroke sleeve: 600 mm -slot in the spindle sto?. meter.: # 80 -radial offset: +-30 mm Glasses: -diameter adjustment range normal: 200-600, 200-500 equipment, okular, 300-800 mm -adjustment range of diameters okular special equipment: 30-300, 50-400, 200-500 mm Pó?okular: -adjustment range pó?okulara diameter: 50-250 mm Drive:-main motor power: 40 kW -the engine speed: 750 RPM. -rapid feed motor power: 2.2 kW -the engine speed rapid feed rate: 3000 rpm. -oil pump motor power: 0.37 kW -engine oil pump: 1500 rpm. -performance oil pump: 25 l/min. Sizes and weights: -distance between centres: 3000-15000 mm -weight for length 6000 mm and 1 support: ok. 30000 kg -extra weight Prov difference length 1000 mm: 1200 kg -the weight of the additional bracket: 1500 kg

gabion mesh production line HEBEI FAKTORY 60X80 / 4300


Line for manufacturing of grid gabionowej HEBEI ANPING WIRE MESH MACHINE FACTORY 60 x 80/4300 was built in the year 2013. Machine for manufacturing of grid gabionowej, hexagonalnej with the following parameters: -manufacturer: Hebei Anping Wire Mesh Machine Factory (China)-the size of the meshes: 60 x 80 mm -maximum width of mesh produced: 4300 mm -wire diameter: 2.0-2.8 mm -capacity: up to 2.5 mb/min. -weight: 18 tons -engine power: 22 kW

Boring Mills STANKOIMPORT 2L614


Boring machine STANKOIMPORT 2L614 produced in 1978. The machine is equipped with measuring, and has upgraded partly electronic. Technical data of boring STANKOIMPORT 2 l 614: -spindle diameter: 80 mm -table dimensions: 800 x 1000 mm -the maximum workpiece weight: 1000 kg -spindle speed: 20-1600 min -engine power: 4.5/6.7 kW -dimensions of the machine: ok. 4300 x 2200 x 2800 mm -weight: 7000 kg

Guillotine Shears STROJARNE PIESOK NTC 2500/4


Guillotine STROJARNE PIESOK NTC 2500/4 produced in 1986 year in Czechoslovakia. The data characteristic guillotine Strojarne Piesok NTC 4 x 2500: -the minimum thickness of cut metal plate: 0.6 mm-maximum thickness of cut metal plate (Rm = 450 MPa): 4 mm-maximum width of cut metal plate: 2500 mm -cutting angle: 1 ' 33 Grad-cutting angle: adjustable -outreach-stand: 200 mm -adjustment range rear bumper: 4-750 mm-main drive motor power: 4 kW -engine power rear bumper: 0.25 kW -infeed bumpers:-dimensions (l x w x h): 3100 x 1600 x 1500 mm-weight: 3800 kg

Diesel engines SKODA 6L350


SKODA DIESEL ENGINE TYPE : 6L350 NUMBER : 135206/3 495 PS 281 RPM YEAR : 1967

Eccentric Presses FPA PMS 63 CP


Eccentric press FPA PMS 63 CP produced in 1983 by the Warsaw Factory Machines. FPA press parameters PMS 63 CP: -maximum load: 63 tons -size disc table: 800 x 560 mm -outreach, the table height: 280 mm -adjustable pitch slider: 8-110 mm -diving slider: 65, 85, 110 strokes/min. -maximum number of inclusions in the clutch to intermittent traffic: 20 on/min. -the largest distance slider from the table: 315 mm -the diameter of the hole in the table: 250/280 mm -the self-alignment capacity of slider in the direction of the axis: 90 mm -thickness: 90 mm -hole diameter: 140 mm -slider surface dimensions: 350 x 315 mm -the diameter of the hole in the slider: 40 mm -the ground clearance between the walls of the body: 380 mm -the width of the t-slots: 22 mm -air pressure: 4.5 at -the engine speed: 1500 rpm. -engine power: 5.5 kW -dimensions (l x w x h): 1550 x 1400 x 2650 mm-weight: ok. 6200 kg -an intermediate table -foot pedal -DTR-technical-functional

Diesel engines MAN D2866 LF05


MAN D2866 LF05 COMPLETE DIESEL ENGINE ENGINE IS RECENTLY OVERHAULED. READY TO WORK. EXWORKS TUZLA / ISTANBUL - TURKEY. READY FOR SHIPMENT.

Diesel engines CATERPILLAR 3412 DT


CATERPILLAR 3412 DT COMPLETE DIESEL ENGINE. ENGINE IS RECENTLY OVERHAULED. READY TO WORK. EXWORKS TUZLA / ISTANBUL READY FOR SHIPMENT

CNC Bending Presses EHT EHPS 11-35


CNC press brake EHT EHPS 11-35 was produced in 1992. Characteristic parameters of CNC presses EHT EHPS 110-3550: -CNC control -maximum pressure: 110 t -maximum length of bending: 3550 mm -maximum length of the pitch slider: 200 mm -the distance between the walls of the body: 3050 mm -outreach: 350 mm -maximum speed bending: 13 mm/s -the maximum distance between a slider and a dining table: 460 mm -the minimum distance between a slider and a dining table: 260 mm -speed: 130 mm/sec. -return speed: 138 mm/sec. -the distance between the bumper: 5-1000 mm -bumper speed: 250 mm/sec. -the height of the bumper over the table: 100-200 mm -a safety distance between the tool and support elements: 128 mm -stop time: 79 ms -the road stopping: 11.3 mm -power of the main engine Y1 + Y2:15 kW -the stopping of the bumper X: 3 Nm -maximum pressure in the hydraulic system: 280 bar -maximum air pressure: 6 bar -oil capacity: 390 l -type of oil: HLPD 46 -operating voltage: three-phase 380 V, 50 Hz -control voltage: 24 V -the total connected load: 21.5 kW -the total rated current: 42 Amp. -maximum switching current: 63 Amp. -machine weight: 9500 kg

Carousel Turning Machines (Lathes) RAFAMET KCF 200


Carousel lathe RAFAMET NCC 200 built in 1963. The machine is accurate, suitable for heavy duty. Lathe was made full service. The data characteristic of lathe RAFAMET NCC 200: -turning diameter: 2400 mm (extended from 2250 mm) -height rolling: 1250 mm -slide the slider of a vertical: 1000 mm -engine: 45 kw -dimensions of the machine: 6100 x 5000 x 5500 mm -weight: 50 tons The advantages of the lathe: -New bearings -new oil, cleaned filters-new hydraulic lines -listed lead screw nut -calibration -It has DTR: full technical documentation in Polish language -made was full servicing of the machine

PRESSA PER PRESSOFUSIONE IDRA


PRESSES for DIE CASTING HYDRA Hydra BRAND MODEL OL 220 PRP YEAR 1995 DESCRIPTION Horizontal press for die casting included STP brand charger Datasheet Closing power 2450 KN Max power injection central extraction Power 180 285 KN KN Max height 550 mm minimum height 180 mm moulds molds 500 mm Race racing mobile plan measures Central ejection stroke 100 mm Dimension 765x765 mm Distance plans within the columns 500x500mm Engine power: 22 Kw total weight 10.2 press Ton 1592x5320x2293 h overall dimensions mm for more details and vision of machinery call us at + 39 030 725026 Monday through Friday from 8:30 19:00 13:00 and 14:00 hours at at

Rolling mills ZGODA 550L


Rolling machines for rubber CONSENT 550L built in 1967 by the Polish Factories of technical equipment CONSENT in ?wi?toch?owice. The machine has undergone complete renovation in the year 2016 for a total of $118000 NET. The scope of the renovation include gears, bearings, lubrication and a wardrobe. Technical data of rolling mills, rubber CONSENT 550 L: -roll length: 1500 mm -diameter of the rolls: 550 mm -engine power: 100 kW

Guillotine Shears PIESOK NTC 2000/4


Guillotine PIESOK NTC 2000/4 after overhaul in 2005. The machine is equipped with electronic counter knife strokes. For the price we offer a spare set of knives. The data characteristic guillotine PIESOK NTC 2000x4 mm: -cutting length: 2000 mm -cutting thickness: 4 mm -engine power: 4 kW -dimensions (l x w x h): 2760 x 1650 x 1520 mm -weight: 3400 kg

Hob milling machines POREBA ZFA 75


POREBA enveloping machine ZFA 75 was produced in 1967 by Mechanical Factory "MUNICH". The machine is designed for the production of gears with straight, oblique teeth and worm gears. During operation without a steady handle, it allows for machining wheels with a maximum diameter of 800 mm, and when working with a steady support, the maximum diameter of the wheel is 450 mm. Technical date: The largest cut-out module: -normally: 6 mm -with reduced accuracy: 8 mm The largest diameter of the gear being machined: -with the support fixed: 450 mm -without a steady: 800 mm The largest diameter of a toothed wheel work with helical teeth: -at a helix angle of 30 °: 500 mm -at a helix angle of 60 °: 190 mm The largest milling length for straight teeth: 275 mm Range of distances between the workpiece the axes and the milling cutter: -the smallest 30 mm -the largest 500 mm Vertical milling cutter: 310 mm The smallest distance from the table surface to the milling cutter axis: 200 mm The largest diameter of the milling cutter: 120 mm Diameter of mandrels for setting the cutters: 22, 27, 32 mm Diameter of the hole on the table: 80 mm The number of spindles of the milling spindle: 7 Range of rotation of the milling spindle: 47.5-192 Vertical cutter range for 1 turn of the workpiece: 0.5-3 mm The range of radial feeds of the milling cutter for 1 turn of the workpiece: 0.1-1 mm The range of axial feeds of the milling cutter for 1 turn of the workpiece: 0.25-1 mm Main engine power: 2.8 kW Machine dimensions: 2395 x 1210 x 1975 mm Milling weight: 3800 kg Equipment: -a set of shift wheels for the guitar -change tires/wheels for the second guitar: 7 pcs. -spindles: 5 items -conical wheels: 2 pcs -claw coupling -tests: 5 items -hook key -DTR-technical and operational documentation It is possible to buy additional equipment of the machine, i.e.: -modular cutters with various modules, from 1-8:100 pieces (additional fee, price: $9990 net, visible in the last two photos)

Gas generators Caterpillar 3520


2055 KW Caterpillar 3520 Gas Generator in Super Insulated Enclosures Eight (8) 2055 KW Caterpillar G3520 Natural Gas Generators in Super Insulated Arctic Enclosures, 2055 KW Caterpillar 3520 natural gas engines with KATO Generators, 2671hp, 60 Hz, 13.8 KV, 1800 rpm, 60 HZ, 0.7PF. year 2009, Hours range 1300 to 2600 since new. Each generator package has its own Super Insulated Arctic Enclosure and designed to operate in severe cold conditions. Mufflers, Batteries, Battery Chargers, Oil Heaters, Prelube System, Water Pumps, Woodward Governor, panels, ABB Medium Voltage Switch Gear and Allan Bradley Motor Control Center and much more. Lots of equipment included with this package. Fast set up to generate immediate power. Excellent Condition, Great Buy on this Complete Package.

PRESSA PER PRESSOFUSIONE IDRA


HYDRO PRESS FOR DIE CASTING Hydro BRAND MODEL OL 220 PRP YEAR 1995 Horizontal press for die casting included STP brand charger Datasheet Closing power 2450 KN Max power injection 285 KN Central extraction power 180 KN 550 mm mould height 180 mm mould height Racing measurements Stroke 500 mm Cabinet plan Central ejection stroke 100 mm 765x765 plans size mm Distance within the columns 500x500mm Engine power: 22 Kw Total weight of 10.2 Ton press Overall dimensions 1592x5320x2293 h mm

Eccentric Presses LE 250/40


Eccentric press LE 250/40 was built in the year 1965 in Czechoslovakia by ZTS Kosice. Characteristic data of the press LE 250: -pressure: 250 tonnes -Max. number of beats per minute: 45-pitch slider: 30-140 mm -the self-alignment capacity of slider: 110 mm -table size: 1120 x 805 mm -size slider: 800 x 475 mm -engine power: 22 kW -the size of the machines: 1350 x 2660 x 2975 mm -weight: 12800 kg

H-Frame Crank Presses PKrR 200/2


Crank press PKrR framework 200/2 pressure 200 tons was built in 1971 by Zamech-. Technical data of the press PKrR 200/2: -nominal pressure: 200 ton-clearance between uprights: 2000 mm-pitch slider: 200 mm-number of jumps: 23, 27, 32 l/min. -distance from the table slider closed (closed is the distance slider from the table in the lower turning position and first engages a): 630 mm-nastwano?? slider: 150 mm-length: 1000 mm-length slider: 900 mm-hole in the table: 1600 x 600 mm-gr ubo??: interface plate 150 mm-width Windows in the rack: 400 mm-the air pressure in the clutch: 3 atn. -odci??aczach air pressure: 5 bar -intake air when jumping individual: 0.035 Nm3/sk. -maximum number of inclusions in the clutch to intermittent traffic: 12 l/min. -main motor power: 22 kW-RPM main motor: 1500 l/min. -engine power to set the slider: 3 kW-engine speed to set the slider: 1500 l/min. -string device, wypych.: 10 t-string device, the power of przytrz: 40 t-string, stroke: 125 mm -maximum air pressure in the device pass design: 6 atn. -the weight of the tool ci?gowego: 2020 kG -the weight of the press without pads: 30580 kG -overall dimensions of the machine (w x l x h): 3100 x 2150 x 5600 mm

Eccentric Presses PLASOMAT PMS 63 MA


Eccentric press PLASOMAT PMS 63 HAS a built in 1989 by the factory Automatic Presses PLASOMAT Warsaw, Poland-Italy. Characteristics of the press PLASOMAT PMS 63MA: -nominal pressure: 63 tons -Board size: 800 x 560 mm -thickness: 90 mm -adjustable pitch slider: 8-110 mm -outreach to table height: 280 mm -the largest distance slider from the table: 315 mm -the diameter of the hole in the table: 280/250 mm -central lubrication system -engine power: 5.5 kW -weight: 5200 kg -dimensions (l x w x h): 1360 x 1530 x 2580 mm

Eccentric Presses PLASOMAT PMS 63 MA


Eccentric press PLASOMAT PMS 63 HAS a built in 1988 by the factory Automatic Presses PLASOMAT Warsaw, Poland-Italy. Characteristics of the press PLASOMAT PMS 63MA: -nominal pressure: 63 tons -adjustable pitch slider: 8-110 mm -outreach to table height: 280 mm -the largest distance slider from the table: 315 mm -Board size: 800x560 mm -thickness: 90 mm -the diameter of the hole in the table: 280/250 mm -engine power: 5.5 kW -central lubrication system -weight: 5200 kg -the press dimensions (l x w x h): 1360 x 1530 x 2580 mm

Eccentric Presses FPA PLASOMAT PMS 63 MA


Eccentric press FPA PLASOMAT PMS 63 HAS built by FPA PLASOMAT Warsaw, Poland-Italy in 1988. FPA presses technical data PLASOMAT PMS 63MA: -nominal pressure: 63 tons -adjustable pitch slider: 8-110 mm -outreach to table height: 280 mm -the largest distance slider from the table: 315 mm -Board size: 800x560 mm -thickness: 90 mm -the diameter of the hole in the table: 280/250 mm -engine power: 5.5 kW -weight: 5200 kg -overall dimensions (l x w x h): 1360 x 1530 x 2580 mm -central lubrication system

Diesel engines MaK 8M35


CNC Bending Presses DENER PUMA CNC 3100 X 200 DMP CNC 20-30


Press brake CNC X 3100 PUMA DENER 200 was built in the year 2012. Characteristics of the press DENER DMP CNC 20-30: -pressure capacity: 200 tons -bending length: 3020 mm -main engine power: 15 kW -oil quantity: 190 l -length: 3940 mm -width: 2500 mm -height: 2690 -weight: 10000 kg

Cylinder head MaK 8M35 & 6M35


MaK M35 COMPLETE CYLINDER HEADS FOR SALE. CYLINDER HEADS ARE SUITABLE FOR MaK 6M35 & MaK 8M35 ENGINES. CYLINDER HEADS FULL WITH EQUIPMENTS. READY FOR SHIPMENT.

Eccentric Presses BZMP KE 2130


Eccentric press BZMP KE 2130 100 TONNES built 1986 year. The parameters of the technicznbe press BZMP KE 2130 100 TONNES: -nominal pressure: 100 tons -the maximum slider stroke: 130 mm-minimum pitch slider: 10 mm -the number of jumps the slider continuous: 100/min -the number of strokes a slider sweeps: 45/min -the size of the jump to its lower position, which corresponds to the nominal pressure-continuous movements: 2.5 mm -the size of the jump to its lower position, which corresponds to the nominal pressure-sweeps: 5.0 mm -table dimensions: 950 x 630 mm -the maximum distance between the table and the slider in the bottom position at maximum stroke: 400 mm -the distance between the uprights of the body (clearance): 400 mm -the size of the adjustment of the distance between the table and the slider: 100 mm -main engine power: 9 kW -dimensions: 2660 x 2380 x 970 mm -weight: 9500 kg

Manzoni 1222


HYDRO PRESS FOR DIE CASTING Hydro BRAND MODEL OL 220 PRP YEAR 1995 About horizontal baler for die casting included brand charger STP Datasheet Closing power 2450 KN Max power injection 285 KN Central extraction power 180 KN 550 mm mould height 180 mm mould height Racing measurements Stroke 500 mm Cabinet plan Central ejection stroke 100 mm 765x765 plans size mm Distance within the columns 500x500mm Engine power: 22 Kw Total weight of 10.2 Ton press Overall dimensions 1592x5320x2293 h mm For more information contact us at + 39 030 725026 machinery and vision from Monday to Friday from 8:30 to 13:00 and from 14:00 to 19:00

Gas generators Caterpillar 3520 Containerized Generators


Caterpillar 3520 Natural Gas Containerized Generator 2055 KW 2055 KW Caterpillar G3520 Natural Gas Containerized Generator Sets. Quantity: Seven (7), 2055 KW Caterpillar 3520 natural gas engines with KATO 4P9 Generators, 2671hp, 60 Hz, 13.8 KV, 1800 rpm, 60 HZ, 0.7PF. year 2009, Hours range 1300 to 2600, Units come with Super Insulated Arctic Enclosures, Units were designed to operate in severe cold conditions. Mufflers, Batteries, Battery Chargers, Oil Heaters, Prelube System, Water Pumps, Woodward Governor, panels, ABB Medium Voltage Switch Gear and Allan Bradley Motor Control Center. Complete equipment with fast set up to generate immediate power. Lots of equipment included with this package. Excellent Condition

Carousel Turning Machines (Lathes) TOS SKJ 12 NC


Control system: NS361 Maximum workpiece height: 1150 mm Max workpiece diameter: 1400 mm clamping diameter: 1,250 mm Engine power: 40 kW Max. Workpiece weight: 6000 kg Machine dimensions: 2970x2770x4250 mm Machine weight: 13000 kg

Grinding Centres Erwin Junker BUAJ 30 CNC


Max. grinding diameter: 290 mm Max. grinding length: 800 mm Max. workpiece weight: 120 kg Control system: true Fanuc Control System: Internal grinding equipment: true Max. grinding wheel diameter: 400 mm Max. Cut-off diameter: 75 mm Main engine power: 7.5 kW Machine dimensions l x h x h: 3000 x 1850 x 1800 mm Machine weight: 2800 kg ?ídící systém Fanuc

CNC Pressbrakes BYSTRONIC PR 150 IPC


Bending Length: 4100 mm System: MODEVA 12 6 axes: 590, 500, 250, 250, 150, 1000, 500 mm. Pressing force: 150 ton Stroke: 265 mm Daylight 550 mm. Closing speed: 200 mm/s Engine power: 11 Kw Electric voltage: 400 V Air Pressure: 8 bar

Vertikal Turning Machines (Lathes) Stanko Ø8000 x 3240 x 125 T


Technical characteristics. The largest diameter of the workpiece - 8000 mm The greatest height. workpiece - 3240 mm The diameter of the disc table - 7100 mm The biggest shift sliders rests vertical (right and left) - 2000 mm The highest levels of vertical travel of the slides (right and left) - 4400 mm Mileage axis slider slides off the center of the shield handle - 150 mm Vertical rotation angle bracket right - -15 ° - 30 ° Vertical rotation angle bracket left (combined) - -15 ° - 30 ° Sliding horizontal slider bracket side - 1250 mm Vertical travel of the slider carriage side - 2,800 mm Maximum weight of the workpiece at a speed table to 15.5 rev / min - 125 tons Maximum weight of the workpiece at any speed - 63 tons The speed range of the table - 0.23 - 19,3obr / min * The largest total cutting force - 160 kN The biggest moment of cutting - 400 Nm Range of feed carriages vertical and horizontal - 0.0352 - 275mm / min The feed rate accelerated sliders and carriages - 2400 mm / min The speed of the beam - 300 mm / min Main engine power - 25 kW Lifting capacity of the crane - 75 ton Suport combined (slide left) Boring spindle diameter - 125 mm Spindle stroke - 1000 mm Maximum torque of the spindle - 3500 Nm Spindle speed n - 20 - 650 r / min Number of degrees of speed spindle - 16 Max-min vertical feed spindle - 0.0352 - 215mm / min The rate accelerated feed spindle - of 2400 mm / min Shift the slider to slide in the y-axis - 2000 mm Feed range slider and bracket Min - 0.0352 mm / min Max - 285 mm / min The feed rate accelerated slider and slide - 2400 mm / min The greatest strength of the cutting blade when running from the front bracket L <= 1000 mm - 80 kN L <= 1700 mm - 50 kN L <= 2300 mm - 30 kN The extreme angles of rotation slide - -15 ° - + 30 ° The electric motor drive main spindle - 10 kW Max spindle feed force - 30 kN Cone Size spindle DIN 2080 - Metric 80

Gas engines JENBACHER FA JMS 612 CO2


1 ENGINE COGENERATION: 1 x JENBACHER J612 C02 YEAR OF MANUFACTURING: 1999 - OVERHAULED 2011 HOURS: approx. 4000 GENERATOR: STAMFORD OUTPUT: 1840 KvA The scope of supply is the following: •Generator (alternator, engine engine and PLC) •Gas train •W ...

Gas engines JENBACHER FA JMS 612 CO2


2. ENGINE COGENERATION: 2 x JENBACHER J612 C02 YEAR OF MANUFACTURING: 1999 HOURS: approx. 25,000 GENERATOR: STAMFORD OUTPUT: 1840 KvA The scope of supply is the following: •Generator (alternator, engine engine and PLC) •Gas train •Water cooling sys ...

Gas engines JENBACHER FA JMS 612 CO2


3 COGENERATION ENGINE: 3 x JENBACHER J612 C02 YEAR OF MANUFACTURING: 1999 HOURS: approx. 16,000 GENERATOR: STAMFORD OUTPUT: 1840 KvA The scope of supply is the following: •Generator (alternator, engine engine and PLC) •Gas train •Water cooling sys ...

Gas generators JENBACHER JGC-320 GS-L.L


FOR SALE JENBACHER JGC 320 YEAR 2010 HOURS 90 000 this engine has run 32,000 since its overhaul 40 FT container included aero table
Find used machinery dealers in your country