electric equipment used for sale

Powder furnace el. or gas Powder curing furnace 6,500 x 1,900 x 2,000 mm 1 Inner dimension length 6,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 7,500 = 15,000 m³/h 10 electric motors 2 pcs 2x 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 110 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device fo ...

The continuous system consists of the following components: Chemical pre-treatment by spraying Dryer Powder coating system Powder curing furnace Conveyor technology (cycle method) Electrical control Overall length: 30,000 mm Overall depth: 4,300 mm Width: 6,500 mm Workpiece weight (max.): 100 kg Temperature: 220 °C Heat output: 80,000 W Workpiece width (max.): 800 mm Workpiece height (max.): 1,200 mm Workpiece length (max.): 2,500 mm Insulating material: Mineral wool 75 kg/m³ Insulating thickness: 150 mm

Powder curing furnaces in various sizes, gas or electric 1 Inner dimension length 1500 - 6,500 [mm] 2 Inner dimensions width 1700 - 1,900 [mm] 3 Inner dimensions height 2,000 [mm] 4 Steel profile substructure 5 walls Galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling rock wool 150mm 75Kg/m² 7 Floor furnace gets 2 entry rails for tray trolleys (optionally with conveyor technology) 8 Temperature 220°C 9 fans 1 - 2 pcs. 2600 - 15,000 [m³/h] 10 electric motors 1 - 2 pcs 1.1 - 6 [kW] , 1450 [rpm], 3 F, 50 [Hz] 11 Thermal power 14 - 99 [kW] 12 hinged or sliding doors on one or both sides 2 - 4 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock Stainless Steel INOX AISI 316 Heating Electric or Gas Heat-Resistant Fans and Heat-Resistant Bearings, Thermoblock Has Overheating Protection

Used ISERNHÄGER Sourdough Line ASB 600 RM - 3pcs available - Capacity 600 litres Visits and test runs are possible by arrangement.

COMPONENTS OF THE SYSTEM Preheating oven Powder coating booth Fluidized Bed Powder Coating Lifting system Automatic Transport System – Conveyor Belt C-80 Electrical control and installation Transport and assembly Fluidized Bed Powder Coating Booth The powder is fluidized in the fluidized bed vessel when the part is preheated and positioned over the fluidized bed container. The lifting system lifts the fluidized bed tank and the part is coated. After the coating process is completed, the fluidized bed is lowered again and an air blowing system blows off the excess powder on the part. The process can be carried out fully automatically. The cab's system is designed for powder coating with powder recovery and consists of a powder chamber for powder application, a monocyclone and a post-filter for extracting powder residues Chamber dimensions Length: 2000 mm Width 1 ...

Powder coating plant (complete) with 3 zones of chemical pre-treatment and Hybird ovens (dryer and curing oven) Gas and electricity (gas or electricity also possible) The facility consists of: Chemical pre-treatment with reverse osmosis system Dryer with hybrid thermoblock Walk-in coating booth with extraction unit KG PSW 8000 Powder curing furnace with hybrid thermoblock Conveyor system with transverse displacement, manual Electric control unit Specification of production Type of workpieces varies Material of the workpieces Steel (other metals or multimetal possible on request) Maximum weight of the load carrier 200 kg System type: Manual conveyor Dimensions of the maximum workpiece in the curing furnace Max. length 3000 mm Max. width 1500 mm Max. height 1500 mm Dimensions of maximum workpiece in chemical pretreatment Max. length 3000 mm Max. width 800  ...

length: . mm height: . mm volt: U2 100 V ampere: I2 40-120 A volt: U1 380 V volt: U0 280 V ampere: I1 37-48 A Manufacturer number.17763 See type plate The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About usMore than 500 machines in stockMore than 8,500 m² of storage space, crane capacity 70 tMore than 10,000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

-Sourdough Fast Fermenter -Model: BRSSF100 -Mobile on castors -completely in stainless steel -400 volts -1.5 kW -Year of construction 2012 -External dimensions approx.: 64x70x125cm WxDxH

Pneumatic semi-automatic filling machine. Dosing volume: 50ml to 1000ml.

Oven, doors single-sided, electric Dimensions: 3,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 54 kW Auxiliary heating: electrically indirect via thermoblock

Dimensions: Length: 7400 mm Width: 4000 mm Height: 3236 mm Extraction capacity: Q = 18000 m³/h P = 15 kW The cabin has a suction machine with filters to suck the powder from the cabin floor. The powder booth is set up in a pit to lower the entire height of the painting line. Manual doors are installed to enter the workpieces into the cabin. The overspray is extracted during powder coating via the floor. On the floor there is a grate for walking on and under the grate there is a second flat floor with automatic self-cleaning system, connected by air ducts with post-filter. A self-cleaning system automatically blows the powder from the bottom to the post-filter (suction machine) and consists of

Oven, doors single-sided, gas Dimensions: 4,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Recirculating air: Q = 12000 m³/h P = 2 x 2.2 kW Heat output: 69 kW Auxiliary heating: Gas indirectly via thermoblock

Chemical pre-treatment 3 zones for powder coating with spray ring (automatic) and manual Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Max. workpiece dimensions (automatic): Length: 6500 mm Width: 1000 mm Height: 2300 mm Max. workpiece dimensions (manual): Length: 6500 mm Width: 2500 mm Height: 2300 mm Tanks are positioned at ground level with a sloping floor. Tank No.1 is thermally insulated and is heated by electric heaters. Achievement: 27 kW. Volume of each tank = 1.00 m³. For degreasing (1st tank), a medium pressure pump is used to operate the 1st spray system. The rinsing phases are also operated by a pump with medium pressure via the 2nd spray system. On the bottom i ...

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

Chemical pre-treatment for powder coating (3 zones) 1 Dimensions of the cabin length 3900 mm Width 1600 mm Height 2500 mm 2 dimensions of the pre-treatment complete length 4000 mm Width 3000 mm Height 4000 mm 3 Passage opening width 1000 mm Height 1700 mm The chemical pretreatment for the use of nanotechnology or phosphating consists of 3 stages in 1 spray chamber. Chemical spray pretreatment works in time and this means that the workpieces are manually pushed into the chamber. After closing the doors, the passage starts and the pumps start spraying. Each pump has different spray times. After the spraying process is finished, there is an alarm indicating that the door can be opened and the workpiece can be pulled out. All pre-treatment functions a ...

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

The curing furnace consists of a tunnel furnace in which the workpieces are baked after coating. The furnace is a straight tunnel furnace. The frame is made of steel with insulated panels. The mineral wool insulation becomes 150 mm thick in a special construction to prevent thermal bridges 1 Inner dimension length 7,000 mm Inner dimensions width 1,000 mm Inner dimensions height 2,500 mm 2 Outer dimensions incl. thermoblock, length 7,200 mm Outer dimensions incl. thermoblock, width 1,300/2,300 mm External dimensions incl. thermoblock, height 2,800 mm 3 substructure 1 set of steel profiles 80 x 80 and 40 x 80 mm 4 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5010 5 Insulation 1 set of rock wool 150mm 75 Kg/m³ 6 Ventilation system 1 set of galvanized steel sheet 7 Temperature max. 220°C 8 fans 1 pc. 7,500 m³/h 9 electric motors 1 pc  ...

Open Powder Spray Stand Dimensions: 2500 x 2250 x 2700 [mm] Extraction capacity: Q = 8000 m³/h P = 5.5 kW Filter: 1 stage: Filter cartridges 4 pieces à Ø 325 x 1000 [mm] 2nd stage: Pocket filter (absolute filter for fine dust) Note: The overspray during powdering is absorbed by the suction unit. The powder spray stand is delivered on rollers and is therefore mobile

Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Extraction capacity: Q = 18000 m³ P = 15 kW The cab has 2 doors on one side for the insertion/outlet of the workpieces. The components are pushed into the cabin for coating via the overhead transport system. Walls, ceiling and doors are made of panels. The filters positioned on the roof absorb dust and other particles from the outside, thus ensuring clean ambient air in the cabin. The overspray during powdering in the cabin is absorbed by the extraction unit

Siebler Stick Pack packaging machine with counter for counting and packing of micro tablets, 1 lane (more lanes available on request), capacity up to 30 sticks per minute. New machine

Working width: 300 mm Number of rollers: 2 St. Feed speed: 20 m/min. weight: 300 kg Dimensions (L/W/H): 4000x600x1500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

welding current: max. 300 A open-circuit voltage: 55 - 76 V connected load frequency: 400 V weight: 75 kg Dimensions (LxWxH): 950 x 560 x 880 mm Inert gas welding machine: - with pulse function - 300 amps - 400 volts - hose package 3m. - ground cable - Wire feed rolls for 0.8 - 0.9 - 1.0 - 1.2 - 2.5 - 3.2 - 4.0 and 5.0mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Ultimate sealing flexibility with dual impression

CTP-Mitsubishi - DPX 460 – Platesetter with Rip-Mate PC Year of construction: approx. 2007 incl. software and accessories incl. roll films in their original packaging For the production of ready-to-print die-cut polyester printing plates Mitsubishi SILVER DIGIPLATE Suitable for the following printing presses: For Heidelberg QM 46, GTO 46, GTO 52 For Ryobi 5xx For Roland Edelmann Practica 400x510mm For Heidelberg Speedmaster SM 52 – PM 52 2x Supply Rolls 1x integrated register punch for PM52- SM52- Autoplate

Salvagnini Mod. Performer Year 2000 Manual loading Manual blades

ADIGE BLM LT652 Model : LT652/B Year of Manufacture : 2002 Laser Generator: DC025 (2500 Watts) Loading Length : 6500 Drain Length : 4500 Hours of Electrical Panel : 60433 Tension Laser Ore : 62285 Chiller : recently replaced Disassembly options - available now.

Coupon holder; suitable for Vacuumatic Vicount 3 machines. Coupon holder; used for Vacuumatic Vicount 3 machines.

Paper counting machine Vacuumatic Vicount 3 PB; serviced and inspected by Vacuumatic Customer Service; compressor overhauled; Air table 76x144cm; Touchscreen; Max. Counting speed 2500 rpm; Max. Stacking height 220mm; Paper weight 25-240g/m2; strip bullet hole; low meter reading 1.7 million Paper counter Vacuumatic Vicount 3 PB; checked and tested by the support of Vacuumatic; compressor rebuilt; air table 76x144cm; touchscreen; max.counting speed 2500 rpm; max.pile hight 220mm; paper weight range 25-240g/m2; tape insert; low counter 1.7 million

Brand: Rollepaal Pipe Extrusion Technology B.V. Model: RSV 8/1 Year of construction: 2005 Pipe outer diameter max: 8 mm Cooling length: 1000 mm Spray pump: 2.2 kW

Screw packers for valve bags Stainless steel Suitable for food and pet food Revised and Function Tested Incl. net scale and new B+L weighing electronics Suitable for valve bags from 10.0 kg - 50.0 kg

Machine type: MIG/MAG welding machine Make ESAB Type LAN 400 Connection voltage 3 x 400 volts Adjustment range 45 – 400 amps Duty cycle 60% ED at 400 amps 80% ED at 355 amps 100% ED at 315 amps Current setting 40 switching levels 3 chokes for the ground cable Cooling transformer by built-in fan Cooling burner water-cooled Design of mobile industrial plant with separate DV case Wire feeder 4-roller drive Fuse 20 Ampere Dimensions L x W x H 900 x 700 x 990 mm Weight 192 kg Age approx. 15 years Condition workshop tested, good, incl. UVV test report Scope of supply welding system with the following accessories: 1 piece welding torch, 3 mtr. long 1 piece ground cable 1 piece pressure reducer 1 Piece Instruction Manual Warranty: 6 months from the date of delivery List factory price from stock €6,900.00 + VAT Pr ...

BRABENDER Moisture Analyzer Semi-Automatic HA includes setting thermometer and 10 sample dishes overhauled and adjusted by our laboratory specialist partner Control thermometer and weight set new Sekutest DGUV V3 newly calibrated

Shaft test device, concentricity tester PAGUS Span: max 460 mm Center height: 72 mm with quick-release device ! used ! Dimensions: 700 x 390 x 255 mm

length: . mm height: . mm volt: U2 104 V ampere: I2 60 A volt: U1 400 V volt: U0 320 V ampere: I1 18-26 A Manufacturer number.32310819 EC/EN 60974-1 See type plate The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About usMore than 500 machines in stockMore than 8,500 m² of storage space, crane capacity 70 tMore than 10,000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

UNOTECH package press from 2018 with approx. 13 - 14,000 Bh. and a sufficient package of wearing parts. the baling press is designed for baling of metal cans and metal blanks Find more here - .ucymachines/

Illumina MISeq, good condition New-generation sequencer / for DNA Find more here - .ucymachines/ Contact us at - sales@ucymachines

10X Genomics GCG-SR-1 The Chromium Controller is in very good condition Find more here - .ucymachines/ Contact us at - sales@ucymachines

Anton Paar ProveTec GmbH Penetrometer Type: PNR 12 Year of construction: 2022 Find more here - .ucymachines/ Contact us at - sales@ucymachines

Aerosol Jet Printer Model - AJ300CE The Optomec AJ300CE Aerosol Jet Printer, introduced around 2011, is an additive manufacturing system designed for high-resolution, non-contact printing of electronic and biological materials onto various substrates, including non-planar surfaces. It utilizes Aerosol Jet technology to deposit fine-feature patterns with feature sizes as small as 10 micrometers. Key Features: - High Precision Printing: Capable of producing feature sizes down to 10 µm, enabling the creation of intricate patterns necessary for advanced electronic components. - Versatile Material Compatibility: Supports a wide range of materials, including conductive, resistive, and dielectric inks, with viscosities ranging from 1 to 1000 cP. - Non-Contact, Conformal Printing: The non-contact deposition process allows for printing on complex, three-dimensional surfaces without damagin ...

Manufacturer: KUKA Year of Manufacture: 2006 Model: KR 100 comp Type of Machine : Industrial Robot Find more here - .ucymachines/ Contact us at - sales@ucymachines

Offer 24589 Specifications: - Suitable for welding steel, aluminum special metals, Cr Ni, etc. - Welding current 450 A 60% ED - 360 A 100% ED - Welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - FRONIUS water cooling unit - Separate wire feeder case - Intermediate package device – wire feeder case 14 m - 4 rolls of wire feeder infinitely adjustable - MIG - MAG Hosepack water-cooled approx. 4 m - Ground cable -Reducer - Mobile undercarriage - Connection 400 V / 6.6 A / 8.7 kVA - Space requirement approx. W 650 x H 900 + 450 x D 1100 mm - Weight approx. 200 kg

Offer 24600 Specifications: - Suitable for welding steel, aluminum special metals, Cr Ni, etc. - Welding current 450 A 60% ED - 360 A 100% ED - Welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - FRONIUS water cooling unit - Separate wire feeder case - Intermediate package device – wire feeder case 14 m - 4 rolls of wire feeder infinitely adjustable - MIG - MAG Hosepack water-cooled approx. 4 m - Ground cable -Reducer - Mobile undercarriage - Connection 400 V / 6.6 A / 8.7 kVA - Space requirement approx. W 650 x H 900 + 450 x D 1100 mm - Weight approx. 200 kg

Offer 24603 Specifications: - Suitable for welding steel, aluminum special metals, Cr Ni, etc. - Welding current 450 A 60% ED - 360 A 100% ED - Welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - FRONIUS water cooling unit - Separate wire feeder case - Intermediate package device – wire feeder case 10 m - 4 rolls of wire feeder infinitely adjustable - MIG - MAG Hosepack water-cooled approx. 4 m - Ground cable -Reducer - Mobile undercarriage - Connection 400 V / 6.6 A / 8.7 kVA - Space requirement approx. W 650 x H 900 + 450 x D 1100 mm - Weight approx. 200 kg

Offer 24604 Specifications: - Suitable for welding steel, aluminum special metals, Cr Ni, etc. - Welding current 450 A 60% ED - 360 A 100% ED - Welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - FRONIUS water cooling unit - Separate wire feeder case - Intermediate package device – wire feeder case 1 m - 4 rolls of wire feeder infinitely adjustable - MIG - MAG Hosepack water-cooled approx. 4 m - Ground cable -Reducer - Mobile undercarriage - Connection 400 V / 6.6 A / 8.7 kVA - Space requirement approx. W 650 x H 900 + 450 x D 1100 mm - Weight approx. 200 kg

Machine Type: MIG/MAG Inverter Welding Machine Make Merkle Type MobiMIG 180 K Serial No. 89.754 Connection voltage 1 x 230 Volt Adjustment range 25 – 180 amps Duty cycle 20% ED at 180 amps 60% ED at 110 amps Current adjustment infinitely variable Cooling inverter through built-in fan Cooling burner gas-cooled Portable assembly system design Wire Feeder 2-Roller Gearbox Fuse 16 Ampere Dimensions L x W x H 450 x 210 x 480 mm Special Accessories ColdMIG Welding Process E-welding, MIG soldering, cored wire welding Weight 17 kg Age 12 years Condition workshop tested, very good incl. UVV workshop test report Scope of supply welding system with the following accessories: 1 piece of welding torch SBT 157 G, 3 mtr. long 1 piece ground cable 1 piece pressure reducer 1 roll of welding wire D-200 coil, 5 kg 1 can of non-stick sp ...

Machine Type: Electrode Inverter Welding Rectifier Make EP-Systems Type Cycle 60.16 Connection voltage 230/400 V Adjustment range 1 – 160 amps Duty cycle 60% ED at 160 amps 100% ED at 130 amps Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter through built-in fan Portable assembly system design Fuse 26 Ampere Dimensions L x W x H 420 x 190 x 300 mm Weight 8 kg Age 10 years Condition workshop-tested new incl. UVV test report Scope of supply welding system with the following accessories: 1 piece ground cable 16 sqmm, 4 mr. long 1 piece electrode cable 16 sqmm, 4 mtr. long 1 piece of hand shield 1 piece facing glass 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2 rows 1 piece mains plug 230 V, soli ...

8008 CM Art. item / Anno/Year: 06-01/90, Hz 50, 380 V, 100 KVA 50%, 250 KVA, 8200 Amp 100%, 36000 Amp short circuit, 710 da N pressure, 300 l/h H2O Water Cooling - Made in Italy The spot welding machine was used weekly about 10 years ago and was fully operational at that time. The machine can be connected at any time and can be checked by qualified personnel by the potential buyer with the product to be manufactured in the future. The machine can be picked up at the current location – as it stands – without warranty and other services for 2800.00€ VHB or shipped plus shipping costs. Alternatively, we can have the machine checked by external specialists, in which case the price is approx. 4500,00€.

Warman Pumps Listing 1.Pump Type: 3 / 2 CAH - Year of Manufacture: 2005 2.Pump Type: 3 / 2 CAH - Year of Manufacture: 2005 3.Pump Type: 3 / 2 CAH 4.Pump Type: AH Find more here - .ucymachines/ Contact us at - sales@ucymachines

Ato Rotopacker 3-tube with autom. Bag feeder Zipper 50/4000. Capacity 2400 bags per hour. On request with dedusting system and other accessories possible.

Sandblaster GLASNER Working is OK Equipped with one filter Voltage: 380 V Internal dimensions: Width 590 mm x Depth 470 mm x H 400 mm Width: 1000 mm Depth: 1500 mm Total height: 1800 mm Weight: approx 400 kg