electric cutting used for sale

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread: 1- 2 inch -Weight: 6.5 kg

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -Replacement jaws: 4 -inch thread: 1/2-2 inch -Transport crate -Weight: 16 kg

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread jaws: 1/4 - 1 1/2 inch -Weight: 8 kg

920 x 920 ED - Program Control Colour monitor Air table Formica side tables with air Spare blade

Rego Herlitzius Kobold Bread Slicer Bread Slicer 10mm 230V - Creel machine - on castors - with lubrication - Cutting width 10mm - for max. 42cm loaves of bread Specifications: - Manufacturer: HERLITZIUS - Model: Leprechaun - Year of construction: 2005 - Power: 0.75 kW - Nominal voltage: 230 V 50 Hz Dimensions: Width: approx. 61 cm Depth: approx. 60 cm Height: approx. 115 cm

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread jaws: 1- 2 inch -Weight: 12 kg

2000 X 2-6 MM cut-to-length line was built in 2018. The line was specially configured for machining stainless steel in a start-stop system with a stationary guillotine and sheet pick-up from the discharge conveyor. Maximum production efficiency is ensured by the use of a special system that packs the sheets into bundles after cutting. Other proven solutions, in turn, guarantee many years of trouble-free operation of the line. The offered cut-to-length line has undergone a general overhaul and is in perfect condition. All components meet the safety standards required by the applicable directives, as confirmed by the CE declaration. The 2000 X 2-6 MM cut-to-length line is fully complete and consists of the following components: – scissor lift table – sheet metal decoiler 7.5 t – infeed and guide system – sheet metal straightening unit – double-side foiling system – gui ...

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutter -inch thread: 1/2-3/4 inch -Weight: 6 kg

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutter -inch thread: 3/8 - 1 inch -In the transport case -Weight: 5 kg

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread: 1 - 2 inch -Transport crate -Weight: 11 kg

Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread: 1 - 2 inch -Transport crate -Weight: 17 kg

LANSUN CNC XG32.05 tube plasma cutting machine was built in China by Wuhan Lan-sun Technology Co., Ltd. The machine, equipped with a reliable plasma source with the highest energy efficiency, is used for precision 3D cutting of tubes with a maximum diameter of 190 mm. The machining process is performed by a torch centrally positioned above the tube to be cut. The rotating head with holder, in turn, guarantees perpendicularity of the cut in relation to the tube axis. The offered LANSUN CNC plasma tube cutting machine is new, unused. Technical specifications of the LANSUN CNC XG32.05 tube cutting machine - maximum tube diameter: 190 mm - maximum tube thickness: 40 mm - inverter plasma cutter: HUAYUAN WELDER LGK-100IGBT quality cutting thickness (steel): 0.3-22 mm rated input power: 17.8 kVA rated input voltage: 3x 380 V; 50 Hz rated output current: 100 A rated output voltage: 12 ...

Key data: 4000 mm, 2000 mm, 10000 W

4000 x 2000mm with Bytrans Extended

Key data: 3000 mm, 1500 mm, 12000 W

3000 x 1500mm - Extended cables for Mezzanine layout

Key data: 3000 mm, 1500 mm, 6000 W

3000 x 1500mm

Laser power: 3,000 watts Type: A04B-0820-B342 Weight system: 750 kg Dimensions LxWxH: 205 x 75 x 120 cm Equipped with: -Stabilizer - Fanuc Power Converter DTU60/2/0/5S - CNC control Fanuc Series 31i-LB

Brand Hegla Type Cutting table Layered Fashion model VSG-H Serial Number 1104 Construction year Jun-95 Weight 3 tons Assets 19 kW Air pressure 6 bars Water pressure: 50Hz Length mm 3700 Width mm 3400 Working height mm 980 Min.-max. glass thickness 2 x 3mm to 2 x 6mm Number of cutting heads 2 cutting heads Separation heating and air cushion Automatic sequence for cutting, breaking, heating and separating functions. Electric connection 380/ 400V Photos/film available: Photos available

Multifunctional punch, punch press, hole punch, pneumatic hole punch -operated: pneumatically -Year of manufacture: 1999 -Dimensions: 600/600/H1300 mm -Weight: 50 kg

Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 1 inch -Drive: via 3 gearboxes -Dimensions: 550/360/H240 mm -Weight: 55 kg

KIMLA POWERCUT LF 1530 6 kW fiber laser for tubes and sheet metal was built in 2021 in Poland. The reliable machine built on a rigid monolithic body equipped with state-of-the-art fibre technology guarantees the achievement of very smooth and even edges along the entire length of the workpiece, regardless of the machined material. The sheets are cut with a high-quality 6 kW fibre optic beam on a steel work table with integrated automatic pallet changing system, which allows uninterrupted machining by simultaneous loading and unloading of the workpieces during the cutting process. All cutting parameters are programmed in the intelligent PC-CAM CNC controller, which allows for very fast and dynamic operation with excellent accuracy. The KIMLA fibre laser cutting machine is also equipped with an integrated cutting system, extending the machine’s machining capabilities to include the cu ...

Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 2 inch -Drive: via 3 gearboxes -Dimensions: 550/360/H240 mm -Weight: 55 kg

: 0390 mm : 240 mm : 1250 mm : 190 mm : 54 mm : 5,5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This grinder has 2 fixed knives and 12 rotating blades. The motor power is 2.2 kW. The grid is replaceable, so the grain size can be changed. Everything works perfectly, motor, bearings, rotor, knife are fine. It's ready to use. I have several of them. There are also other document shredders for sale. Please also see my other ads.

turning diameter over bed: 250 mm turning diameter over slide rest: 145 mm turning length: 550 mm center height over bed: 125 mm centre distance: 550 mm bed width: 135 mm spindle bore: 26 mm turning speed range - stepless: 50 - 2.000 U/min power requirement: 750 W 3-jaw-chuck diameter: 125 mm taper in tailstock-quill: MK 2 dia. of quill: 30 mm quill stroke: 70 mm voltage: 230 V weight of the machine ca.: 120 kg dimensions of the machine ca.: 1,25 x 0,60 x 0,50 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 8405 Type: Peddimax No 1 Producer: Peddinghaus Created: 2019 Parameters: Operating hours: 150 h Strength: 140 t Pressure: 300 bar Equipment: Flaps

Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 1 inch -Drive: via 3 gearboxes -Dimensions: 550/360/H240 mm -Weight: 60 kg

S. No.: 3392-014 Format (cm): 76 Equipment / Additional information: Side tables, air table, 1xreserve knife

A complete CNC double gantry plasma cutting system Microstep with oxyfuel torch for nesting, bevel cutting and tube processing is available. 1) Plasma cutting system, max. processing length: 16500mm, max. processing width: 2500mm, max. processing width including shaft: 3700mm, max. material thickness VA/structural steel: 20mm/40mm, number of gantries: 2. Gantry 1: with a plasma rotator and a Kjellberg HiFocus 280i neo plasma cutting source. Gantry 2: fully automatic oxy-acetylene torch for possible equipment of a second torch carriage. Pipe cutting device: pipe diameter range: 30mm-700mm, max. pipe length: 16500mm, operating hours: approx. 15000h. 2) Filter system Donaldson Cyclopeel DFPRO 16, volume flow: 16000m³/h, filter elements: 16. Documentation available. On-site inspection is possible. Expected to be available from the end of 2025/beginning of 2026. Pictures are from commissioni ...

x-travel: 0 mm y-travel: 0 mm table length: 600 mm table width: 400 mm total power requirement: 2 kW weight of the machine ca.: 1500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 500 mm table width: 350 mm ampere: 65 A Control: AGIEVISION 5 CNC total power requirement: 20 kW weight of the machine ca.: 4000 kg dimensions of the machine ca.: m A G I E (Switzerland) CNC - Controlled Wire Cutting EDM Machine Model AGIECUT PROGRESS V 3, Year 2007 Working range, X Y Z (=height) 500 x 350 x 426 mm Wire head, U-V axis (helical/taper cuts) + / - 30 °/ +/- 70 mm Resolution of axes 0.0001 mm Speed for positioning the axes up to 3 m/Min. Tolerances (If machine is new) 4 µ Workpiece dimensions, L x W x H max. 1.050 x 650 x 420 mm Max.weight of workpiece with/w.o. Dieelektricum 400/800 kg Clamping System Universal Beams with fixing holes Cutting wire Ø 0.2 – 0.33 mm Size of wire roll up to 25 kg Cutting speed of wire  ...

turning diameter over bed: 420 mm turning diameter over slide rest: 290 mm turning length: 900 mm turning diameter in the gap: mm turning speeds: 40 - 2000 U/min centre height: 210 mm spindle bore: 38 mm total power requirement: 4,0 KW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 2,4 x 1,1 x 1,3 m Lead and feed spindle lathe - 3-jaw chuck 220mm - Quick-change tool holder with 5 cassettes - Steady rest - Chip tray - Operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

welding current: 15 - 40 A cutting capacity: 1 - 16 mm open-circuit voltage: 96 V Required air-pressure: min. 4 bar connected load: 3,6 kW connected load frequency: 230 V weight: 9,0 kg Dimensions (LxWxH): 371 x 153 x 232 mm Exhibition machine Inverter plasma cutter with accessories: Cutting torch with 4 m cable, earthing clamp with 2.5 m cable, air pressure gauge, Mask and brush. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thread dia.: 3 - 10 mm Tools speed: 120 - 600 U/min table-size: 250 x 350 mm throat: 250 mm voltage: 380 V threading length: 80 mm total power requirement: 0,55 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 0,7 x 0,7 x 1,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thread dia.: 12 mm : max. 600 U/min. working area: max. 1100 mm engine output: 0,6 kW weight: 30 kg Electric tapping machines for M3 - M12 threads, 8 pcs. quick-change chuck with slipping clutch. Adjustable via display: variable speed, adjustable depth, choice of Main direction of rotation, torque. Documentation in English! Options: - Clamping table with T-slots: 990x700x800mm. - Magnetic base. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thread dia.: M3 - M16 mm : max. 187 U/min. working area: 180 - 2000 mm engine output: 0,7 kW Electric tapping machines for M3 - M16 thread, Angle adjustable. 9 pcs. Quick-change chuck with slip clutch. Adjustable via display: variable speed, adjustable depth, material selection, choice of Main direction of rotation, thread selection. optional: Clamping table with T-slots: 990x700x800mm. Magnetic base. Also available: M14 to M24 and M27 to M33. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thread dia.: M10 - M33 mm : 35/115 U/min. : 320 Nm air pressure: 6 - 8 bar working area: 400 - 2000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 400 mm turning diameter over slide rest: 280 mm turning length: 1000 mm turning diameter in the gap: mm turning speeds: 70 - 2000 U/min centre height: 195 mm spindle bore: 54 mm tailstock quill taper MT: 3 MK connected load frequency: 400 V total power requirement: 2,2 kW weight of the machine ca.: 0.85 t dimensions of the machine ca.: 1,95 x 1,0 x 1,75 m Professional industrial machine 3-axis digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 280mm Bezel fixed Bezel rotating 4-fold steel holder. Halogen machine light Machine light Foot brake removable chip tray, chip protection wall Hardened and ground bed rails Complete coolant system Feed protection Machine feet Machine tool The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thread dia.: M3 - M8 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

HSK63-B,F Test Mandrel Suitable for Vollmer machine types: QWD 750 / QWD 760 / QWD 750 H / QWD 760 H / VPulse 500 and all models from the QXD series (200/250/400)

Cutting device, pneumatic press, punch -Type: 290 908 -Max. pressure: 8 bar -Dimensions: 300/340/H270 mm -Weight: 25 kg

Thread cutting chuck, thread chuck, tap chuck, thread cutting apparatus -with slip clutch -Integrated reversing gearbox with quick return -Thread cutting sizes: M5-M20 -Recording: MK4 -Dimensions: 380/95 mm -Weight: 4.1 kg

TOOLMET GATO GC-G-M-2040 oxy-fuel cutting machine was built in 2020 in Poland by Toolmet Sp. z o.o. This extremely efficient machine is an excellent choice for businesses placing emphasis on high accuracy and repeatability of the produced parts. It enables precise, 4-axis shape cutting of workpieces made of thick steel sheets. The machining process is performed fully automatically by means of a reliable gas torch according to pre-programmed cutting programmes. The work table with a length of 4000 mm and width of 2000 mm is equipped with a sectional extraction system with 6 pneumatically controlled sections. This solution effectively eliminates any contamination generated during the cutting process, ensuring a high level of safety and great user comfort. In order to guarantee smooth movements and high positioning accuracy, a lubrication-free drive system and powerful servo motors in all l ...

Wire guide elements for metal, spacing 100-200 mm, 15 mm longer Using these wire guide elements reduces the diameter of the workpieces that can be machined. Suitable for Vollmer machine types: QWD 76 P / QWD 750 / QWD 760 / QWD 750 H / QWD 760 H / VPulse 500

Fully Automatic Bread Slicing Machine Manufacturer: TREIF Type: DISKUS – SB Technical data: Round knife cutting bread slicer Oil-free cutting even of warm breads 3 cutting thicknesses selectable: 8mm, 10mm and 12mm Bread passage: L 380 x H140-160 x D280 mm Automatic bread gripper suitable for all types of bread with bread rack for bagging with sight glass cover for optimum safety during the cutting process Easy cleaning without having to move the machine 400 volts / 0.9 kW / 10 A Dimensions: H110 x W90 x D76 cm Weight: 200 kg Mobile on 4 pulleys with 2 brakes Year of Make: 2010 Function checked, machine is thoroughly cleaned and ready for immediate use! Condition, see original pictures! If you have any questions, email or call.

thread dia.: - mm threading length: - mm throat: ca. 2000 mm total power requirement: 0 kW weight of the machine ca.: 0,2 t dimensions of the machine ca.: 1,30,82,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

REF-2741 KRONEN SPIRELLO SP150 VEGETABLE SPIRAL CUTTING MACHINE Manufacturer: KRONEN Model: SPIRELLO SP150 Serial no.: 199 Year: 2017 Automatic machine for cutting vegetables into long spirals. With a capacity of up to 340 kg/h (depending on the product), the SPIRELLO 150 is an unbeatable option for processing large amounts of vegetables into perfect and decorative spirals and strips. Mobile on casters for easy movement. Electrical specifications: 230 V/50 Hz/0.9 kW/1PH Working pressure: 6 bar Two product centring units: diameters 85 mm and 150 mm Max. product length: 300 mm Max. product weight: 2,5 kg Overall dimensions (mm): 850 x 600 x 1,800 (LxWxH) Weight: approx. 180 kg CE marking

turning diameter over bed: 400 mm centre height: 195 mm turning diameter over slide rest: 246 mm turning length: 650 mm spindle turning speed - stepless: 0-2500 U/min total power requirement: 7,5 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 2x1.3x1.6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Code: 0355 Brand: AVOLA - GERMANY Model: GAMA 65 K - CE Standard Cutting centre for timber joinery, beams, timber roofs, sawmills, balconies, garden furniture and various – CE Standard Technical data: Lower cross-cut saw with rotating table and tilting blade Vidia blade diameter mm 650 Hole 30 Pneumatically operated safety cover Motor 10 Kw Motor speed 3000 rpm Pneumatic clamping cylinders Pneumatic cross-cut device with two-hand control Electric blade tilt adjustment 90–30° with flat digital display 5–175° Cutting height at 90° 245 mm Cutting height at 45° 164 mm Cutting height at 30° 113 mm Laser cutting guide Table dimensions mm 1500 x 1500 Work table height mm 1000 Handling brackets for forklift truck Right Roller conveyor mm 3000 x 600 - Support guide 5000 mm Left Roller conveyor mm 3000 x 600 - Support guide 5000 mm Overall dimensions of ass ...

turning diameter over bed: 270 mm turning diameter over slide rest: 130 mm turning length: 500 mm spindle turning speed - stepless: 40-3000 U/min weight of the machine ca.: 1 t dimensions of the machine ca.: 1.5x0.8x1.7 m Digital read-out HEIDENHAIN Misc.accessories www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 360 mm centre height: 170 mm centre distance: 650 mm turning dia. over face-slide: 196 mm spindle bore: 42 mm inner taper MT: 5 spindle turning speed - stepless: 20-3250 U/min weight of the machine ca.: 1,6 t dimensions of the machine ca.: 200 x 125 x 165 cm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.