edge trim used for sale

diameter range 2,2-8 mm shaft length under head 6-40 mm output pieces/min 250

diameter range M8 shaft length under head 6-80 mm output pieces/min 200

Unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -Sale: Handover in the current condition as seen -Case: slight damage, see photos -Trimming unit: for trimming the protruding edges on the front and rear edge -Adjustment range: 400 to 840 mm -Clamping: pneumatic -Motors: Holz-Her 750 W / 2600 rpm -Saw blade: Ø 160 mm -Dimensions: 1010/450 / H540 mm -Weight: 94 kg

Unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -Manufacturer: Hemag, saw unit can be swiveled by 30 ° -Saw blade: max. Ø 350 x 30 mm -Motor: Perske type DKNS 120/2 3.0 kW / 2830 rpm -Protection class: IP 54 -Dimensions: 950/780 / H630 mm -Weight: 115 kg

Unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -Manufacturer: Homag, trimming unit from edge banding machine BRANDT KM 35 -Motor: Homag type LF-40-L -Power: 0.27 kW / 12000 rpm -Voltage: 220V / 200 Hz -Saw blade: Ø 90 mm -Pneumatic components: Bosch -Individual components: see photos -Dimensions: 500/370 / H680 mm -Weight: 26 kg

Unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -Manufacturer: Homag, trimming unit from edge banding machine BRANDT KM 35 -Motor: Homag type LF-40-L -Power: 0.27 kW / 12000 rpm -Voltage: 220V / 200 Hz -Saw blade: Ø 90 mm -Individual components: see photos -Dimensions: 590/280 / H750 mm -Weight: 27 kg

Terminal and trim box, road cell -Terminal box: for up to 4 load cells -Inputs and outputs: via PG screw connections -Protection class: IP 65 -4 inputs, cable gland M12 for cable diameter: 2 to 6.5 mm -1 output, cable gland M20 for cable diameter: 7 to 12 mm -Number: 2x available -Price: per piece -Dimensions: 205/110/H70 mm -Weight: 0.8 kg

Modular unit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG trimming unit for trimming the protruding edges on the front and rear edges -with heavy leadership -Milling unit: swiveling -2x motors -Motor type: -Power: 0.23 kW -Voltage: volts -Frequency: Hz -Speed: 18,000 rpm -Other engines with other services in stock for an additional charge -Dimensions: 1000/420/H655 mm -Weight: 140 kg

Unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG trimming unit for trimming the protruding edges on the front and rear edges -with heavy leadership -Milling unit: swiveling -2x motors -Motor type: -Power: 0.23 kW -Voltage: volts -Frequency: Hz -Speed: 18,000 rpm -Other engines with other services in stock for an additional charge -Dimensions: 1020/400/H700 mm -Weight: 110 kg

weight: 25 kg Motor speed: 2850 Rpm Engine power: 1.5 kW Auction-ID: A7-45261-10

STIHL HSA66 cordless hedge trimmer, dimensions approx. 1100x250x200 mm STIHL HS45 motorised hedge trimmer, dimensions approx. 1100x250x200 mm Auction-ID: A7-45419-32

Equipped with yanmar engine; Lamps: 4× LED; Lamp power: 150 W per lamp; Lighting area: 2400 m²; Rotation: 340°; IP class lamps: IP65; Max. height: 5500 mm; Operation: manual (winch); Max. wind speed (certified): 110 km/h; Engine: Yanmar L70AE; Cylinders: 1; Displacement: 320 cm³; Speed: 3000 rpm; Fuel consumption: 0.5 l/h; Tank capacity: 41 litres; Avg. Running time per tank: 82 hours; Cooling: air; Generator: Linz SP 10M; Rated power: 4.2 kVA; Frequency: 50 Hz; Voltage: 230 V; Power on auxiliary connection: 3.2 kVA @ cos φ 1; Double insulation; dimensions 1640x1100x2500mm; Weight: 600kg Auction-ID: A1-40133-289

Includes: (1x) work table 200x100x77cm, (1x) 2-door cabinet 97x40x97cm. Auction-ID: A1-44726-76

pressure:65 t distance between columns:930 mm stroke:1100 mm distance table/ram, stroke up:2400 mm table surface area:1340x700 / 930x1085 mm hole in the table:320x260 / 600x410 mm table height over floor:850 mm side window:700 mm ram surface:990 x 930 mm power requirement:15,0 kW weight:8,0 t Dimensions (WxDxH):2,8 x 2,6 x 5,2 m blank holder / ejector in ram:hydraulic side shifting device:hydraulic

Pressure:100 t distance between columns:910 mm stroke:600 mm distance table/ram, stroke up:1000 mm table surface area:1340x680 / 910x1085 mm hole in the table:700 x 510 mm table height over floor:800 mm side window:680 mm ram surface:1230x680 / 910x1000 mm capacity of ejector:7,5 t ejector stroke:150 mm power requirement:15,0 kW weight:9,5 t Dimensions (WxDxH):2,3 x 1,9 x 3,6 m light guard:Sick blank holder / ejector in ram:hydraulisch

Without clamping devices and supports, only the press Technical data Manufacturer: REIS GmbH & Co. Maschinenfabrik Type: EC 8-20D Year of Make: 1994 Machine Type: Hydraulic trimming press Press force: 200 kN Retraction force: 35 kN Max. stroke: 500 mm Installation height: 800 mm Speeds: Fast forward: 620 mm/s Pressing cycle: 90 mm/s Return: 540 mm/s Hydraulic pressure: max. 175 bar Fuel tank capacity: 355 l Pneumatics: min. 6 bar, connection R1/2" Motor power: 7.5 kW Connected load: 8 kVA Control voltage: 24 V Clamping surface: Table: 800 x 600 mm Plunger: 800 x 500 mm Dimensions (L x W x H): 1895 x 1400 x 3150 mm Weight: approx. 5000 kg Configuration Vertical construction Suitable for die casting deburring processes Documentation available Used machine

Trimming machine Make: VITAP Type: RC 92 New machine Technical data: - 2 high frequency motors HP.0,75 (Kw 0.55) each. 12000 RPM, in vertical opposite position with inverter; - 2 cutter heads with cutters one knife straight 15° the other radius 3mm; - CE standards Options (for a surcharge): - Couple of cutters (without knives) ? 274,00 - Set 8 knives 15 degrees angle and radius 2 mms. ? 122,00 - Set 8 knives 15 degrees angle and radius 3 mms. ? 122,00 - Pneumatic lifting of the upper motor ? 474,00 - Optional for panels max. high 120 mms ? 227,00

- with lateral Kappsaege

Table dimensions: 850 x 300 mm. abrasive belt width: 150 mm. abrasive belt length: 2510 mm. abrasive band speed of 16 m/s. Ver ? laipsn suportas angle is 90. Engine power: 2.1 kW. Stakl ? weight: 148 kg. Made In Austria.

AUTOMATIC EDGE BANDING machine SCM OLIMPIC K 1000 second hand machine volt. 380/50 for solid wood max. 10 mm. / PVC / veneers / melamine composed by : technical details : min. panel length mm. 120 min. panel width mm. 70 panel thickness min./max. mm.10/60 edge thickness min./max. mm.0,4/10 total installed power Hp 9 composition machine : 1. lower glue pot 2. motorized roller for automatic feeding 3. edge shear 4. end trimmer unit . motor Hp 0,3 . rpm 12.000 5. top and bottom ( rough ) edge trimmer unit . 2 motors Hp 1,1 . rpm 12.000 6. top and bottom ( fine ) bevel edge trimmer unit . 2 motors Hp 0,3 rpm 12.000 7. edge glue scraper unit integral protection enclosure

Edge grinding with oscillation and veneer sanding WEIBERT new WJ-KS30 400V 3 KW (4 HP) n = 2840 RPM Work table 960 x 350 mm Table height 230 mm Belt rear 1050 x 200 mm Belt speed 20 m / sec Oscillation stroke 20 mm Oscillation motor 0.25 KW (0.34 PS) A/can be switched off Machine table and guides made of grey cast iron Quick adjustment of tilting 90 °-45 ° with degree display Weight 400 kg Dust nozzle 120 mm Rollers pull-out extension table Band width 150 mm WJ-R00200 option: Band width 200 mm WJ R00300

Type AKV 88 F Without glue tank Max. edge thickness 3 mm Max workpiece height 50 mm Feed speed : 0-7 m/min (0,25kW) Power consumption 3,2 kW Work table height 890 mm Made in Germany 1996 y. Transport dimensions 1360x680x1220 mm Weight 150 kg

Work table: 750 x 290 mm, table height: 185 mm band length: 2600 mm strap width: 150 mm abrasive belt rear: 850 x 200 mm grinding unit swiveling: 90°-45° belt speed: 20 m / sec. Additional table: 330 x 330 mm oscillation stroke: 20 mm Oszilationsmotor: 0.25 (0.34 kW) suction connection Ø: 120 mm motor power output S1 100%: 3.0 kW (4,0 PS) motor power S6 40%: 4,5 kW (6.0 HP) voltage: 400 V machine dimensions (W x D x H): 1700 x 700 x 1080 mm weight approx.: 180 kg

Koelle edge planing machine model FKF 51 is in good condition, ready to use. L x W x H = 3000 mm x 700 mm x 950 mm Weight approx. 200 kg Built in 1982 Engine No. 390 The rubber rings at the pressure rollers should be times replaced. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Tool cabinet for bending tools pull-out drawers, allows the two-sided access to the tools -any adjustment of the inserting roofs -robust steel construction, powder-coated, in any colors of the RAL pallet -side fork guide rails for transport by means of forklifts (cavity under the cabinet) -the drawers run on roller slide rails (serve as additional stabilization) . number of drawers: 4 squares - Mass of a drawer : - total height 1200mm / total width 850mm / total depth 1050mm - mass of the faeces set in a drawer: compartment heahe on 210mm (is varriabel) technical height can be used in total without intermediate boeden 990mm compartment width usable 130mm depth usable 980mm - number of intermediate boeden: 3 stubs ; ready for use

Edge Abkappen thrower HolzHer Built in 1978 Weight approx. 220 kg L x W x H: 80 x 60 x 150 cm The machine is in good condition, ready to use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Angle cutting machine. NEW.

Tool cabinet for bending tools Suitable for WILA/TRUMPF Tools or type B L / W / H: 1180 mm x W 850 mm / H 1200mm, 350kg -extendable drawers, allows the two-sided access to the tools -arbitrary adjustment of the inserting roofs -robust steel construction, powder-coated -side fork guide rails for transport by means of forklifts (cavity under the cabinet) run drawers Roller slide rails (serve as additional stabilization) - the cabinet can be disassembled - number of drawers: 4 sets - Mass of a drawer : - total height 1200mm / total width 850mm / total depth 1180mm - Mass of the Fa echer in a drawer: compartment hoehe set to 210mm (is varriabel) technical height total usable without intermediate boeden 990mm - specialist width usable 130mm depth usable 1100mm - Number of intermediate boeden: 4 Stueck / completely continuous; new ready for use

Edge press of PanHans 923 with preheating ruler Working length 250 cm maximum 80 mm thick L x W x H: 300 x 60 x 100 cm Weight approx. 300 kg Built in 1976 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

480 m2 steel construction stage used, good condition, see pictures Length approx. 21 m Width approx. 23 m Height lower edge 2.45 m Height top edge 2.9 m fastened with screws and nut Grid distances adjustable in length without shelf shelves Negotiation price: € 14,000.00 net from stock Disassembled and loaded from stock Transport and assembly possible on request. Visit possible at any time by appointment. More information on request. Constantly over 3000 lfm pallet racks in stock by numerous manufacturers Changes and errors in the technical data, information prices and intermediate sale reserved! See our Terms and Conditions, all prices excl. VAT from stock Purchase / Sale We are looking for, or offer numerous items from various areas on an ongoing broom-pure company clearances Operational resolutions Fast- flexibl ...

Weibert form7-75 Edge sanding machine infinite angle adjustment (0 ° 90 °) vertical and horizontal loop with oscillating abrasive belt (good stock removal) spring loaded clamping device for belt Diameter of the grinding roller rubberized 80 mm Belt: 2260 x 150mm Contact surface (graphite Edition) 170 x 820 mm Table height adjustment 80 mm Suction nozzle D = 100mm Engine power 2,2 KW 400V 50 Hz G & pieces 5900750

Tool cabinet for bending tools / exhibition object suitable for AMADA/PROMECAM or type A L / W / H: 1050 mm x W 850 mm / H 1240mm, 310kg - for AMADA/Promecam tools -extendable drawers, allows double-sided access to the tools -any adjustment of the inserting roofs -robust steel construction, powder-coated -side fork rails for transport by forklift (cavity under the cabinet) -the drawers run on roller slide rails ( serve as additional stabilization) -the cabinet can be disassembled - Number of drawers: 4 squares - Mass of a drawer : - Total height 1200mm / Total width 850mm / Total depth 1050mm - Mass of the faeces in a drawer: - Fachhhoehe set to 210mm (is varriabel) - Fachhoehe total usable without intermediate boeden 990mm - Fachbreite usable 130mm - Technical depth usable 980mm - Number of intermediate boeden: 3 stueck

Weibert form 7-85 Edge sanding machine Infinite angle adjustment (0 ° to 90 °) Vertical and horizontal loop with oscillating abrasive belt (good stock removal) Table height adjustment by Handwheel Spring loaded clamping device for belt Grinding roller diameter 80 mm Belt: 2510 x 150mm Contact surface (graphite Edition) 180 x 950 mm Table height adjustment 80 mm Suction nozzle D = 100mm Engine power 2,2 KW 400V 50 Hz G & pieces 5900850

Tool cabinet for bending tools suitable for AMADA/PROMECAM or type A L / W / H: 1050 mm x W 850 mm / H 1240mm, 310kg -extendable drawers, allows the two-sided access to the tools -any adjustment of the inserting -robust steel construction, powder-coated -side fork guide rails for transport by means of forklifts (cavity under the cabinet) -the drawers run on roller slide rails (serve as additional stabilization) Cabinet can be disassembled - Number of drawers: 4 squares - Mass of a drawer : - Total height 1200mm / Total width 850mm / Total depth 1050mm - Mass of the faeces in a drawer: compartment hhoehe set to 210mm (is varriabel) - Fachhoehe total usable without intermediate boeden 990mm - Tray width usable 130mm - Depth usable 980mm - Number of intermediate boeden: 3 stueck

Edge glue machine HolzHer express 1437 Glue, caps, flush milling, RADIUS milling / Beveling, scraping, cutting tool for rolling edges Total revision 10 years ago everything top Year of construction 1989 L x W x H: 500 x 120 x 170 cm Weight approx. 1800 kg The machine is in top shape, ready for use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Type SE-360D Thickness of panel 10-60 mm Edging thickness 0,3-3 mm Feeding speed 13-22 m/min Air pressure 0,6 MPa Voltage 380V/50Hz Total install power 10,5 kW Min. panel dimensions 150(L)x150(W) mm Made in 2017 y. Transport dimensions 4420x900x1560 mm Weight 1400 kg

Trumpf TKF 103 welding edge shaper. 220 Volt under electricity ready for use Special price

Holzstar KSO 750 Edge Grinder With oscillating sanding belt for good removal performance, a clean grinding pattern and a longer service life of the sanding belt With height-adjustable grinding table Standard with -45° to +45° infinitely adjustable miter and workpiece stop Infinitely inclined grinding unit (0°-90°) for vertical and horizontal grinding Table height adjustment by means of handwheel Robust work table made of cast iron with T-grooves, stable stand of the machine when working With height-adjustable additional table for contour grinding Fast and easy sanding belt change via quick clamping system Spring-loaded clamping device for uniform belt tension Abrasive sole with graphite coating as standard Suction nozzle Ø 100 mm With lockable storage option in the standard substructure Equipment details: Thanks to the infinitely variable grinding unit, the edge gri ...

Manual Edger Esterer EWD DKV with task table good condition ! Immediately available !; Well

Machine is still in < operation and fully functional solid up to 20mm rolls PVC to 3 mm caps flush milling RADIUS milling milling Schwabbleln chamfer

Edge glue machine HolzHer express 1437 Edge gluing, flush milling, caps flush milling with chamfer milling or RADIUS milling with sep. Aggregate Schwabelscheiben 2 mm and two units for chamfering or just milling milling ABS edge 2 additional units for RADIUS Hours of operation 1072.5 hours Masch. No. 721/9-203 L x W x H: 400 x 120 x 170 cm Weight approx. 900 kg Built in 1992 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Edge gluing machine - see picture Next: Edge gluing machine NEY-SENIOR SKM 100/3 gemaess Pictures

Technical data: -Plate thickness up to 6-40 mm -Pipe Beveling min. Ã? 100 mm -Max bevel in one run 10 mm - speed 2.6 m / min -Drive 400 V / 2,2 kW -Space requirement approx. B T 550 x 500 x H 700 mm -Weight approx. 65 kg

Type HLP Voltage 220 V Power 400 W Length 120 mm Diameter 8 mm Made in Germany Weight 70 g

Automatic Edge Banding machine type OCMAC BS 21 . second hand composition : - glue pot - edge-trimming unit (2 motors) Kw 2 each one . rpm 12.000 with cabinet with HF converter Hp 5 volt. 380/50