eccentric used for sale

Attachment: eccentric screw pump Manufacturer: Seepex Type: BN 35-12 Machine number: 176490 Year of construction: 2005 Power: 2-40 m3/h Pressure: 1--8 bar Speed: 1450 RPM. Connection suction side: DN 150 Port side: DN 125 Length: 2400 mm Condition: used, ready

Specifications: Capacity 63 tons Stroke rate 140 h/min Projection 250 mm Plunger stroke 8-100 mm Table , WxD approx. 700 x 480 mm Installation height approx. 400 mm

Attachment: eccentric screw pump Manufacturer: Netsch Type: NE 20 B Machine number: 263384 Year of construction: 1995 Power: 1,3 m3/h Pressure: 12 bar Engine: HEW, 0.37 KW, 400 V, 1380 RPM Connection suction side: DN 40 Port side: DN 40 Length: 1200 mm Condition: used, ready for operation, with variable speed gears

Specifications: Capacity 300 to Stroke rate 35 strokes Plunger width 1000 mm Projection 450 mm Plunger stroke 20 - 140 mm Plunger adjustment 80 mm Engine power 30 hp Weight roughly estimated 18 tons

Attachment: eccentric screw pump Manufacturer: Netsch Type: A 60B Machine number: 263381 Year of construction: 1995 Performance: 19 m3/h at 2 bar Pressure: 1--8 bar Motor: 4 KW, 400V, speed 1445 RPM Connection suction side: DN 100 Port side: DN 100 Length: approx. 2000 mm Condition: used, ready

Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm

Attachment: eccentric screw pump Manufacturer: Netzsch Type: 2 NE 60A Machine number: 221234 Year of construction: 1990 Power: 47 m3/h Pressure: 4-8 bar Speed: 1450 RPM. Engine: North Power: 15 kW, 400 V Connection suction side: DN 100 Port side: DN 100 Length: approx. 2800 mm Other: with an electric variable speed gears Condition: used, ready

Attachment: eccentric screw pump Manufacturer: Allweiler Type: SLBP 720-1 Machine number: 7640010 Year of construction: 1989 Power: 67-484 l / min Speed gear: 50-280 RPM. Engine: Bauknecht Power: 5.5 kW, 380 V Speed: 1440 RPM Connection suction side: DN 100 Port side: DN 100 Length: 1800 mm Condition: used, ready

Eccentric shaft for hot forging press K8548 6300T Weight, kg 27 800

Attachment: eccentric screw pump Manufacturer: Netzsch Type: NM031BY02512B Machine number: 409232 Year of manufacture: 2009 Output: 200-300-350 l / h Pressure: 4-6-8 bar Motor: Lenze Speed: 1410 RPM. Inlet connection: DN 50 Port side: DN 50 Length: 1200 mm Condition: used, ready for operation (new stator)

2 x Schmidt Eccentric Press ZHS-4/36 - 600 tons of pressing force Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.

Attachment: eccentric screw pump Manufacturer: Seepex Type: BN 1-12 Machine number: 176411 Year of construction: 2005 Capacity: 150-2200 l / h Pressure: 2 bar Speed: 1400 RPM Inlet connection: DN 50 Port side: DN 50 Length: 1200 mm Condition: used, ready

Eccentric press with black shield, Pressure capacity 15 t, Stroke adjustment from 5 - 60 mm, Table dimensions: 550 x 360 Dimensions: W 800 x D 1200 x H 2200 mm Weight 800 kg,

Attachment: eccentric screw pump Manufacturer: Netzsch Type: NM031BY Machine number: 321637 Year of construction: 2001 Power: 90-1500 l / h Speed: 24-400 rpm. Pressure: 0-16 BAR Motor: 1,5 kW, 400 V North, Connection suction side: DN 70 Port side: DN 70 Length: 1700 mm Condition: used, ready

Single column - eccentric press WEINGARTEN type E 40 Masch. No. 643 / 62 Year of construction 1963 Pressure capacity 40 ton. Projection 250 mm Table opening 150 x 80 and Ø 200 mm Table area 560 x 460 mm Plunger area 250 x 200 mm Adjustable ram stroke 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100 / 130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 volts, 50 Hz Table height above floor 840 mm - Clutch-brake combination thanks to WEINGARTEN friction threaded clutch with OT flow protection - Electric stroke release via two-hand operation - Overload protection by crushing plate - Manual grease central lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirements L x W x H 1800 x 1500 x 2200 mm Weight 3.1 ton.

Attachment: eccentric screw pump Manufacturer: Netzsch Type: NE 30B Machine number: 235197 Year of construction: 1992 Power: 0.2-1.4 m3/h Pressure: 0-6 BAR Motor: Stöber 1.1 kW, 400 V Inlet connection: DN 50 Port side: DN 50 Length: 1500 mm Miscellaneous: electrical Verstellgetrieb with ventilation Condition: used, ready

pressure: 160 t throat: 350 mm stroke: 20-140 mm stroke of worktool slide: 40-60 Hub/min ram adjustment: 75 mm total power requirement: 15 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Attachment: eccentric screw pump Manufacturer: Netzsch Type: NE 69 A Machine number: 253233 Year of construction: 1994 Capacity: 25m 3/h Engine: Dietz KW: 5.5 Voltage: 400V Connection suction side: DN 100 Port side: DN 100 Length: 2300 mm

pressure: 100 t throat: 410 mm stroke: 8-112 mm no. of strokes doubel-strokes per min.: 55 / 82 ram - range of adjustment: 80 mm table surface area: 950 x 700 mm ram surface: 700x450 mm hole in the table: Ø 280 mm table height: 850 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 7,0 t dimensions of the machine ca.: 1400x2200x2800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t throat: 400 mm stroke: 6-125 mm ram - range of adjustment: 100 mm dayligth: 400 mm table surface area: 1100x750 mm no. of strokes: 60 Hub/min ram surface: 800x550 mm hole in the table: Ø 150 mm total power requirement: 14 kW weight of the machine ca.: 9,0 t dimensions of the machine ca.: BxTxH 1500x2200x3500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Machine: eccentric screw pump Manufacturer: Netzsch Type: 3 NE 08 Machine number: 253173 Year of construction: 1994 Capacity: approx. 300 l / h Engine: Dietz Drezhal: 1390 RPM KW: 0.55 Voltage: 400V Connection suction side: 3/4 inch Connection pressure side: 3/4 inch Length: 800 mm

pressure: 80 t throat: 300 mm stroke: 8-112 mm no. of strokes: 60 Hub/min ram adjustment: 80 mm table surface area: 700x550 mm ram surface: 400x300 mm table height: 870 mm hole in the table: Ø 280 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 5,0 t dimensions of the machine ca.: 1500x2000x2700 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Self-priming eccentric screw pump including 2/3 hose fitting with nut nut MG90/65 sleeve VA and 2/3 hose fitting with groove nut DN65/65 sleeve VA mounted on a chassis. Technical data: Rated power 4 020 / 8 160 l/h Engine power: Level 1 1.0 (1.36) kW (PS) Level 2 1.9 (2.6) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A Dimensions: Length 1 270 mm Width 500 mm Height 810 mm Weight 57 kg Material 1.4301 / AISI 304 Connections: front MG90 AG top DN65 AG can be used for mash

Self-priming eccentric screw pump including 2/3 hose fitting with nut nut MG90/65 sleeve VA and 2/3 hose fitting with groove nut DN65/65 sleeve VA mounted on a chassis. Technical data: Rated power 9 960 / 19 380 l/h Engine power: Level 1 2.5 (3.4) kW (PS) Level 2 4.2 (5.71) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A Dimensions: Length 1 270 mm Width 500 mm Height 810 mm Weight 90 kg Material 1.4301 / AISI 304 Connections: front MG90 AG top DN65 AG can be used for mash

Self-priming eccentric screw pump including 2/3 hose fitting with nut nut MG90/65 sleeve VA and 2/3 hose fitting with groove nut DN65/65 sleeve VA mounted on a chassis. Technical data: Rated power 840 - 8 100 l/h Engine power 2.2 (3.0) kW (HP) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A Material 1.4301 / AISI 304 Connections: front MG90 AG top DN65 AG can be used for mash

Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request

pressure: 63 t throat: 315 mm stroke: 8-100 mm no. of strokes: 140 Hub/min ram - range of adjustment: 63 mm table surface area: 1200x630 mm ram surface: 800x315 mm hole in the table: Ø 110 mm table height: 820 mm tool hole in ram: Ø 50 mm dayligth: 335 mm total power requirement: 7,5 kW weight of the machine ca.: 5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tech. Data Nominal press force 1000 kN at maximum stroke adjustment - commute 6.5 mm 1250 kN at maximum stroke adjustment - commute 3.5 mm Strokes with endurance 125/83/63 Hube/min Usable stroke rate 50 50 38 / min. Throat depth 320 mm, clamp 380 mm Stroke adjustment 10-120 mm, Stosselverstellung 80 mm Stosselflaeche 800 x 320 mm, recording journal 50 / 85 Tabletop table top hole, 900 x 630 mm 230 mm, Durchfalloch in the table 300 / 400 x 250 mm Drive - 7,5 / 5,5 kW Bulk 1350 x 2080 x 2780 mm, Btto 8900 kg

Pressure capacity: 8000 kg Maximum cutting area - 200 mm2 for material strength 40 kg / mm2 Horizontal radius 200 mm Clearance between the side walls 160 mm Fixed hub 35 mm Pin hole in the Stossel 38 x 60 mm Adjustability of the Stossels 70 mm Weight of 400 kg of the Presse Operating instructions The machine is located in the new value. State, probably never in use. Control actuator Stober

Capacity: 56 l/min Motor: 1,5 kW Working pressure: 6 bar - Input with threaded supports DN 40, DN 50 - Output with threaded supports DN 50 - With friction geared motor for stepless speed control - Mobile chassis - With cable and CE plug Measurements and Weight: Length: 1700 mm Width: 550 mm Height: 1030 mm Weight: kg

Year: 1979 Capacity: 25 l /min Motor: 0,75 kW Working pressure: 13 bar - Input with threaded supports DN 15 DN 25 - Output with threaded supports DN 25 - With friction geared motor for stepless speed control - Mobile chassis - With cable and CE plug Measurements and Weight: Length: 1400 mm Width: 410 mm Height: 1020 mm Weight: kg

Year: 1979 Capacity: 20 l /min Motor: 0,75 kW Working pressure: 19 bar - Input with threaded supports DN 15 DN 25 - Output with threaded supports DN 25 - With friction geared motor for stepless speed control - Mobile chassis - With cable and CE plug Measurements and Weight: Length: 1400 mm Width: 410 mm Height: 1020 mm Weight: kg

Eccentric spiral pump NETZSCH NE80A 15-20 to/h used - in very good condition! UNI-ALTD Capacity: approx. 15-20 t/h Year: 1984 Type: NE80A Flange: 1 x DN 120 1 x DN 150 Comment: the pump is tested, 100% functions guarantee! Measurements: Length: 2030 mm Width: 600 mm Height: 1300 mm

pressure: 40 t throat: 230 mm stroke: 8-88 mm throat: 230 mm no. of strokes: 130 Hub/min ram - range of adjustment: 63 mm table surface area: 560x450 mm ram surface: 250x200 mm hole in the table: Ø 190 mm table height: 790 mm tool hole in ram: Ø 40 mm weight of the machine ca.: 3,0 t dimensions of the machine ca.: 1000x1800x2500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Capacity: 8.4 m3/h Operating pressure test 13 bar Engine: 3.5 kW - With connectors: DN 65, DN 50, DN 65 - With chassis mobile 2 steering and 2 buck wheels - With cable and CE plug 16A Dimensions and weight: Length: 2200 mm Width: 500 mm Height: 1080 mm Note: Pump 100% tested, with functional guarantee On request, it can be infinitely adjusted with frequency inverter for additional costs. Connections can be changed at an additional cost.

Progressing cavity pump for separator feeding, original pump housing available - was built into a special pump housing, functional due to project change dismantled: Flow rate: approx. 20 m³/h Drive power: 7.5 kW

pressure: 130 t throat: 350 mm stroke: 16-200 mm no. of strokes: 55 Hub/min ram - range of adjustment: 100 mm table surface area: 1200x700 mm ram surface: 730x530 mm hole in the table: 300x210 mm table height: 900 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 8,0 t dimensions of the machine ca.: BxTxH 1500x2200x3500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 63 t throat: 280 mm stroke: 8-100 mm ram surface: 310x260 mm table surface area: 620x500 mm hole in the table: Ø 250 mm no. of strokes: 56/84 Hub/min ram - range of adjustment: 63 mm weight of the machine ca.: 4,0 t dimensions of the machine ca.: 1200x1900x2800 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Nominal force 400 kN Stroke rate - 70/140 / min Motor 3/4 kW Exploitable stroke - at constant. Clutch brake temperature 50/45/min Capacity - material thickness 4-6.4 m - with single strokes, 2-3.2 mm - with continuous stroke Table 660 x 530 mm, table top 650 x 515 x 75 mm Stroke adjustment - 10-125 mm, Dimensions 1250 x 1600 x 2370 mm - High , Btto 4500 kg Reconditioned machine - warranty 9 months from delivery date

Eccentric Press Brand Ebu Type EP15 Table size 400x430mm Max pressure 15 000kg Table height adjustment Table passage D160mm Stroke adjustment 4-70mm Ram bore 40mm Projection 200mm Max distance table-tappet 320mm Single/Duration Stroke Shield Flywheel D600mm 400V 1.0kW Machine weight ca. 870 kg The purchase price is net. Can be viewed and tested in our warehouse. Delivery is possible at an additional cost. All information without guarantee!

Type / type: N 25 Year of make: 1977 Manufacturer / make: Weingarten Rated pressure: 25 t Number of strokes: 140 / min Radius slide center to frame: 200 mm Window in frame: 240 mm distance table slide: 250 mm Stroke adjustment / adjustment of stroke: 8 ... 80 mm Ram adjustability/adjustment of ram: 50 mm Ram size / surface of ram: 355 x 220 mm Table size / surface of bed: 560x 400 mm Hole in table: 160 mm Power of main motor:3 kW Weight / weight: 2,23 t

Stock Number: 3785 ECCENTRIC PRESS Manufacturer: PMB, Type: EPFT 100 Machine NO.: 004301, Year of manufacture: 2002 Specifications: Table size 780 x 590 mm Stroke length 8-120 mm Number of strokes per minute 55 Projection 300 mm Operating height 395 mm Total power 7.5 kW Pneumatic clutch. Gear ratio. Hydr. Overuse protection. Weight: 5500 kg

Compressive force: 25 t Projection: 200 mm Table size: 450 x 600 mm Table adjustment: 240 mm Plunger adjustment: 70 mm Stroke adjustment: 4 - 80 mm Stroke rate: 150 rpm Drive motor: 380 V, 1.1 kW Space required: 1600 x 850 x 2000 mm Weight: approx. 1450 kg

pressure: 100 t throat: 410 mm stroke: 8-112 mm no. of strokes: 55/82 Hub/min ram - range of adjustment: 80 mm table surface area: 950x700 mm ram surface: 700x450 mm hole in the table: Ø 280 mm table height: 800 mm total power requirement: 11 kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: BxTxH 1600x2200x3000 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 75 t

Specifications: Capacity 75 tons Stroke rate 90 strokes Projection 300 mm Plunger stroke 16 - 140 mm Plunger adjustment 80 mm Table size approx. 800 x 600 mm Installation height max. approx. 400 mm

pressure: 80 t throat: 320 mm stroke: 8-112 mm no. of strokes: 60 Hub/min ram - range of adjustment: 80 mm : 355 mm table surface area: 720x550 mm ram surface: 400x310 mm sheet thickness - max.: 11 mm weight of the machine ca.: 9,5 t Overall size: 2000x2000x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 80 t throat: 280 mm stroke: 8-112 mm no. of strokes: 55 / 82 Hub/min ram - range of adjustment: 80 mm table surface area: 800x570 mm ram surface: 560x355 mm hole in the table: Ø 280 mm table height: 800 mm tool hole in ram: Ø 50 mm total power requirement: 7,5 kW weight of the machine ca.: 6 t dimensions of the machine ca.: BxTxH 1600x2200x3000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: Capacity 63 tons 2 strokes 105 rpm and 140 rpm large projection 450 mm ! Plunger stroke 8-100 mm Plunger adjustment approx. 70 mm Table , WxD approx. 700 x 780 mm Plunger, W x D approx. 450 x 280 mm

pressure: 63 t throat: 330 mm stroke: 8-100 mm no. of strokes: 56/84 Hub/min ram - range of adjustment: 63 mm table surface area: 850x600 mm ram surface: 550x360 mm hole in the table: Ø 240 mm table height: 800 mm tool hole in ram: Ø 40 mm weight of the machine ca.: 4,5 t dimensions of the machine ca.: 1300x2000x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 160 t throat: 340 mm stroke: 20-120 mm no. of strokes: 45 Hub/min ram - range of adjustment: 100 mm table surface area: 800x620 mm ram surface: 500x400 mm hole in the table: Ø 360 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 12 t dimensions of the machine ca.: 2200x2000x3600 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.