137,066 used machines on RESALE, but how to find them? Machine Search
Scope of delivery: 1. Chemical pre-treatment by spraying (in cycle process) 2. Dryer 3. Powder coating system 4. Powder curing furnace 5. Conveying technology, semi-automatic Ue3Zjkdi72 6. Electrical control Hall/ Parking space Floor area of the system max. 12,000 x 6,500 mm Industrial flooring hall floor Workpiece sizes Max. part dimensions L= 500mm, H= 1,500mm, W= 500mm Steel parts range Conveyor P&F chain conveyor in cycle method, semi-automatic Pretreatment Chemical Energy supply Electricity On-site power (max. 88 kW) Gas On-site performance Compressed Air On-Site Performance Water On-site service Calculation Type of system Cycle system Conveying speed 3.2 meters/min Length per cycle L = 1,600 mm Time for clock movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minutes Time for clock stop: Ts = 8.5-12 minutes Total time for clock Tt = Tm + Ts ...
The continuous system consists of the following components: Chemical pre-treatment by spraying Dryer Powder coating system Powder curing furnace Conveyor technology (cycle method) Electrical control Overall length: 30,000 mm Overall depth: 4,300 mm Width: 6,500 mm Workpiece weight (max.): 100 kg Temperature: 220 °C Heat output: 80,000 W Workpiece width (max.): 800 mm Workpiece height (max.): 1,200 mm Workpiece length (max.): 2,500 mm Insulating material: Mineral wool 75 kg/m³ Insulating thickness: 150 mm
Manual hand unit: J/N Automatic for single pieces: Ja J/N Automatic for frames: Ja J/N The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Used belt-type chamber machine from Saccardo, type Dublino 860. New 2012.
Metal bellows coupling, claw coupling, connecting coupling, torsionally flexible coupling -Claw coupling: Torsionally flexible claw coupling -Boret: Ø 20 mm -Dimension: Ø 176 x 140 mm -Weight: 12,6 kg
Metal bellows coupling, claw coupling, connecting coupling, torsionally flexible coupling -Claw coupling: Torsionally flexible claw coupling -Bohrung: Ø 10 mm -Dimension: Ø 108 x 95 mm -Weight: 3.5 kg
Metal bellows coupling, claw coupling, connecting coupling, torsionally elastic coupling -Claw coupling: Torsionally flexible claw coupling -Bore: Ø 10 mm -Dimensions: Ø 90 x 70 mm -Weight: 1.8 kg
Inv. Num. : 7918 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1984, GO 2006 Parameters: Rolling force: 12.5 t Max. workpiece diameter: 70 mm Workpiece width: 2000 mm Power consumption: 4 kW Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
Inv. Num. : 7920 Type: UPW 12,5 Producer: VEB Wema Bad Düben DDR Created: 1980-GO 1998 Parameters: Rolling force: 12.5 t Max. workpiece diameter: 70 mm Workpiece width: 200 mm Power consumption: 4 kW Length: 1125 mm Width: 1400 mm Height: 1150 mm Weight: 2100 kg Equipment: Thread Rollers Ring magazine for automatic operation Support ruler
Round cylinders, pneumatic cylinders, standard cylinders, air cylinders, pneumatic stamps, air stamps, compact cylinders, short-stroke cylinders -Stroke: 60 mm -Piston diameter: 60 mm -Piston rod: 16 mm -Dimensions: 207/80/H80 mm -Weight: 1.6 kg
Dividing head, dividing head, tool holder for grinding, drill grinding machine, milling cutter grinding machine, drill grinding holder, milling cutter grinding holder -Mouth size: Ø 160 mm -without: interchangeable jaws -Central bore: mm -Dimensions: 320/230/H220 mm -Weight: 30 kg
Bezel moving, moving bezel, steady rest, lynette -Bezel: driving -Max. Passage: Ø 120 mm -Center height: 150 mm -Drawing: with the photos -Dimensions: 280/390/H470 mm -Weight: 18.5kg
Messsystem für Polar 155 EMC Duxon SMD / Measuring System for Polar 155 EMC Duxon SMD Serial-No. 022 490 Messsystem für Polar 155 EMC Duxon SMD Measuring System for Polar 155 EMC Duxon SMD Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
4 Heads, Drill Bit Cooling and Lubrication, Continuosly Variable Stroke and Spindle Speed Control, Dürselen Drill Belt for Drilling Support
Shaft vice, machine vice -Clamping diameter: max. 90 mm -Dimensions: 390/220/H190 mm -Number: 1x available -Price: per piece -Weight: 38 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Short taper mount: Ø 140 mm -Passage: Ø 76 mm -Weight: 30 kg
Moving bezel, moving bezel, resting stick, lynette -Manufacturer: TOS for lathe type SUS80 -Max. Passage: Ø 200 mm -Plating: brass -Top height: 230 mm -Drawings for the photos -Quantity: 1 piece -Dimensions: 530/200/H740 mm -Weight: 100kg
Bending tool, die, lower tool, die tool, folding tool, press tool, forming tool -Die tool: Forming tool / Press tool -Profile: Ø 45 mm -Dimensions: 535/195/H140 mm -Weight: 35 kg
Three-jaw chuck, three-jaw lathe chuck -Mouth size: Ø 240 mm -without: interchangeable jaws -Conical mounting type: Ø 102 mm -Weight: 29 kg
Sprockets, duplex sprocket, sprocket -Number of teeth: 23 teeth -Diameter: 345 mm -Total width: 120 mm -Tooth width: 30 mm -Socket: O 90 mm -Number: 3x sprockets available -Price per piece -Weight: 50 kg -other sprockets: in stock
Sprockets, duplex sprocket, sprocket -Sprocket pitch: Duplex 1 1/2 x 1 -Number of teeth: 25 teeth -Diameter: 318 mm -Total width: 100 mm -Tooth width: 24.1 mm -Inside diameter: 80/130 mm -Number: 25x sprockets available -Price: per piece -Weight: 33.5 kg -other sprockets: in stock
turning diameter: 570 mm turning length: 2000 mm control: Sinumerik 805 Siemens swing diameter over face slide: 365 mm main spindle speeds:: 3-2.500 U/min drive of main spindle: 15/19 kW spindle bore: 62 mm spindle head: DIN 55027 No.8 tailstock taper MT: 5 quill stroke: 190 mm pinole diameter: 80 mm feed range - long. and cross: 0,01-50 mm/u total power requirement: 50 KVA weight of the machine ca.: 5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Spindle Drilling Machine 1994 (Engine New 2015) Machine no.: PB04.08.94.261 4 drill heads Available: immediately Located: Germany
Key data: 20000 kN, 135 mm
Dosing 1: Plasticizing 1: Screw diameter mm 135 Screw diameter mm 120 | 135 | 150 Dosing Stroke Screw stroke mm 610 Maximum injection capacity cm3 6899 | 8731 | 10780 Screw speed min-1 125 Worm torque Screw torque Nm 14000 Maximum screw speed reduced torque min-1 135 Reduced torque maximum screw speed Nm 12963 Reduced screw speed maximum screw torque min-1 112 Maximum screw torque reduced screw speed Nm 15630 Plasticizing performance (3-zone) 1.2 Recovery rate (3-zone screw) 1.2 g/s 165 | 222.9 | 231,3 Plasticizing performance (barrier) 3 Recovery rate (barrier screw) 3 g/s 208.3 | 279.2 | 264,6 1) Values for polystyrene up to injection unit 2550 according to ETR 10100 1) Data for GPPS up to injection unit 2550 acc. ETR 10100 2) Values for HDPE from injection unit 3550 according to ETR 10100 2) Data for HDPE from injection unit 3550 onward acc. ETR 10100 3) Values for HDP ...
Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Mouth size: Ø 200 mm -Short cone mount for: bayonet disc attachment -Cone size: 6 -Cone: Ø 106 mm -Bolt circle: Ø 133.4 mm -Through hole: Ø 54 mm -Weight: 15 kg
three-jaw chuck, three-jaw lathe chuck -Handover: in current condition as viewed -Short cone: has been shortened -Chuck size: Ø 200 mm -Through hole: Ø 54 mm -Hole: cone Ø 104.5 mm -as per pictures, without additional accessories -Weight 14.4 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Throughout: Ø 80 mm -Short taper: 6 -Weight: 28 kg
Wedge bar chuck, three-jaw chuck, three-jaw lathe chuck, power chuck, hydraulic chuck -Mouth size: Ø 250 mm -Cone: Ø 94 mm -Thread: M20 -Gradient: 2.5 mm -Weight: 33.3 kg
Saddle Stitcher With brochure function Counter: 1.9 million Connecting Bridge DSF-DSC Duplo LDR , 2017 2 CollationTower Duplo DSC – 10/60, 2020 Cover Feeder Duplo DSF-CFL, 2016 Counter Duplo DKT-K, 2017 Head and foot trimming Duplo DKT-200, 2017 Front Trimmer Duplo DBMS-T, 2017 Stitcher Duplo DBMS-S, 2017 Folder Duplo DBMS-F2, 2017 In production Available: immediately Located: Germany
three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Cone: Short cone 8 Ø 139 mm -Bolt circle: Ø 170 mm -Through hole: Ø 80 mm -Weight: 24 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Throughout: Ø 70 mm -recess recess: Ø 194 mm -Weight: 20 kg
Copy part head, copy head, part head -Copy head rail for: lathe -Dimensions: 100/81/H1747 mm -Weight: 43 kg
Moving steady rest, moving steady rest, steady rest, lynette -Max. Passage: Ø 50 mm -Hole spacing: 388 mm -Tip height: 153 mm -Drawing: in the photos -Dimensions: 430/90/H360 mm -Weight: 14 kg
Directivity: 100 t Projection: 325 mm Table size: 490 x 3500 mm Max. stroke: 160 mm Pushrod speed upwards: 206 mm/s Slide speed downwards: 68 mm/s Hydraulic drive: 380 V, 15 kW Space requirement: 3500 x 1650 x 2760 mm Weight: 5500 kg
pressure: 100 t throat: 380 mm stroke: 400 mm power capacity: 22 kW dayligth: 600 mm ram surface: 600x500 mm table surface area: 720x600 mm weight of the machine ca.: 9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Bezel, stick, lynette -max. Passage: Ø 30 mm -Tip height: 175 mm -Drawing: in the photos -Dimensions: 425/130/H390 mm -Weight: 10.8 kg
Bezel, stick, lynette -Max. Passage: Ø 30 mm -Tip height: 225 mm -Drawing: in the photos -Dimensions: 425/130/H440 mm -Weight: 12.5 kg
Centrifugal Pump, Water Pump DUE EFFE ES 75 Motor: 0.55 kW 2800 rpm 220 / 380 V Dimensions: 300 x 180 x 290 mm
Bezel, stick, lynette -Max. Passage: Ø 128 mm -Edition: gunmetal -Dimensions: 500/85/H740 mm -Weight: 35 kg
Three-phase electric motor DUTCHI NL Type: DM 160 M2 ( DM160M2 ) Power: 11 kW Speed: 2935 rpm Voltage: 230/ 400 V amperage: 35.3/ 20.4 A New !' frequency: 50 Hz/ 60 Hz degree of protection: IP55 with flange
Bezel, stick, lynette -max. passage: Ø 240 mm -Tip height: 290 mm -Edition: ball bearings -Technical drawing: in the photos -Dimensions: 760/130/H610 mm -Weight: 125 kg
Bezel, steady rest, lynette -max. passage: Ø 210 mm -Centre height: 390 mm -technical drawing: in the photos -Dimensions: 600/125/H625 mm -Weight: 53.5 kg
Beading tool, punching tool, separating tool, punching tool, punch, punching die, punching punch -Punching tool with: bending function -Admission bolts: 50 mm -Dimensions: 495/495/H430 mm -Weight: 282 kg
Flange mounting, driving flange -Chuck flange with: driving pin -Outer diameter: 250 mm -Short taper mount for: bayonet disc mounting DIN 55027 -Cone size: 8 -Hole circle: Ø 171.4 mm -Weight: 17 kg
Three-jaw chuck, three-jaw lathe chuck -lining size: Ø 190 mm -Rezess: Ø 155 mm -Passage: Ø 54 mm -Weight: 11 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 240 mm -Throughout: Ø 77 mm -Weight: 18 kg
Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 200 mm -Hole circle: Ø 133 mm -Passage: Ø 20 mm -Weight: 22.1 kg
Three-jaw chucks, three-jaw lathe chucks, power chucks -Chuck size: Ø 200 mm -Short taper: 6 -Weight: 25 kg
Two-jaw chuck, 2 jaw chucks, vice, face plate -Chuck size: Ø 160 mm -Hole circle: Ø 136 mm -Cone: Ø 115 mm -Weight: 11.9 kg
maximum number of results exceeded
please refine your search
