Engel Duo 17060/2000 Injection molding machines

Dosing 1: Plasticizing 1:
Screw diameter mm 135
Screw diameter mm 120 | 135 | 150
Dosing Stroke Screw stroke mm 610
Maximum injection capacity cm3
6899 | 8731 | 10780
Screw speed min-1 125
Worm torque Screw torque Nm 14000
Maximum screw speed reduced torque min-1 135
Reduced torque maximum screw speed Nm 12963
Reduced screw speed maximum screw torque min-1 112
Maximum screw torque reduced screw speed Nm 15630
Plasticizing performance (3-zone) 1.2 Recovery rate (3-zone screw) 1.2 g/s 165 | 222.9 | 231,3
Plasticizing performance (barrier) 3 Recovery rate (barrier screw) 3 g/s 208.3 | 279.2 | 264,6
1) Values for polystyrene up to injection unit 2550 according to ETR 10100 1) Data for GPPS up to injection unit 2550 acc. ETR 10100
2) Values for HDPE from injection unit 3550 according to ETR 10100 2) Data for HDPE from injection unit 3550 onward acc. ETR 10100
3) Values for HDPE according to ETR 10100 3) Data for HDPE acc. ETR 10100
Injection 1: Injection 1:
Injection Flow Injection rate cm3/s 1504 | 1904 | 2350
Specific Injection pressure (regenerative) bar 2085 | 1648 | 1335
Specific Spray Pressure Increased Injection pressure (max) bar 2300 | 2000 | 1620
1) at least 80% injection pressure
Nozzle 1: Nozzle 1:
Nozzle stroke stroke mm 1100
Nozzle contact pressure kN 210,0
Mass cylinder 1: Material cylinder 1:
L/D screw length L/D ratio 25.0
Number of heating zones incl. nozzle 1) Heating zones incl. nozzle 1) 8
Heating capacity 1) Heating wattage 1) kWel 88.5
1) Maximum of existing equipment
Clamping unit: Clamping unit:
Clamping force kN 20000
Minimum clamping force kN 2000
Opening force (with pressure pad) kN 1600
Opening force (with rapid traverse) Opening force kN 614
Opening stroke mm 3000
Maximum distance between platen mm 3800
Minimum mold height 1) Minimum mold height 1) mm 800
Maximum mold height 1) Maximum mold height 1) mm 1800
Lights Distance between tie bars horizontal x vertical mm x mm x mm 2000 x 1600
Clamping plate size horizontal x vertical Platen size horizontal x vertical mm x mm 2700 x 2430
Maximum mold weight moving plate 1) 2) Maximum mold weight moving plates 1) 2) kg 41330
Maximum mold weight fixed plate 1) Maximum mold weight stationary platen 1) kg 41330
Maximum mold weight total 1) 2) Maximum mold weight total 1) 2) kg 62000
Dry Cycle (Euromap 6) Hub Dry cycle (Euromap 6) stroke mm 1400
Dry cycle (Euromap 6) Time Dry cycle (Euromap 6) time s 5,5
1) Minus any existing magnetic holding plates 1) Minus any existing magnetic holding plates
2) Minus any existing rotary table 2) Minus any existing rotary table
Ejector 1: Ejector:
Ejector stroke ejector stroke mm 400
Ejector force kN 385.0
Drive unit: Drive unit:
Drive power main motors Installed power main motors kW 265
Oil reservoir capacity - Injection unit l 1600
1) Additional oil quantity for initial filling approx. 15% 1) Additional oil quantity for initial filling approx. 15%.