dr hochstrate used for sale

: 6 St. : 70/100 kg : ca. 820 x 740x 560 mm weight: ca.110 kg drawer measurements: 450 x 600 mm Colour: 7035/5012 RAL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Material No.: 1.2487.0 // Serial No.: 1267-3491416 Operating hours: 26512 h Equipment / Additional information: Max. working pressure PS: 13,00 bar Compressed air inlet temp. TS: 3 – 60 °C Ambient temperature: 3 – 50 °C Phases: 3 / Frequency: 50 Hz Voltage: 400 V Full load current: 17 A Full load current drive motor: 14 A Electrical diagram: STG-03000 00

clamping plate: 595 x 445 mm drawing length: 400 mm stroke: 400 mm weight of the machine ca.: 1.600 t dimensions of the machine ca.: 1.400 x 1.200 x 1.500 mm Minimum/maximum cutting speed: 0 - 20 m/min Minimum/maximum return speed: 40 m/min Maximum workpiece diameter according to DIN6885 (bore): 230 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Roller conveyor / roller conveyor with drive Condition: Used Model: Drive: Flat Belt Year of Make: 2013 Total length: approx. 33500 mm -consists of 12 parts: 1x approx. 1500 mm, 1x approx. 2000 mm, 10x approx. 3000 mm -result in 4 different systems: 1x 6500 mm, 3x 9000 mm Total width: approx. 650 mm Conveyor width: approx. 595 mm Roll diameter: approx. 50 mm Roller spacing/ center distance: approx. 50mm/ 100mm Material: Steel Frame height: approx. 120 mm Frame depth: approx. 25 mm Colour: green Including SEW motor (0.25 KW) Price per meter Feet to be ordered separately Internal Article Number: 2026021101 The conveyor technology ran until dismantling. Thanks to the excellent workmanship of the conveyor technology, your material glides smoothly to its destination, even under high loads. Tailor-made solutions for your intralogistics We are your competent pa ...

Paper drill Dürselen Corta PB 04 N; very good condition; cleaned and tested; 4 drill heads; Drilling lubrication and cooling; Speed regulation; speed table stroke adjustable; max. Stacking height 50mm; insertion depth behind drill 42mm; Sliding table; Hole spacing 31.7-293mm; Endless drilling belt. Paper driller Dürselen Corta PB 04 N; good condition; cleaned and checked; 4 heads; lubrication and cooling system; adjustable drilling speed; adjustable table hub speed; max.pile hight 50mm; depht behind the driller 42mm; slide table; distance between the holes 31,7-293mm; Endless Drill Band.

Vertical Drilling and Milling Center Brother TC-22A with 4th Axis Year of Make: 1999 Control: Brother Technical data: Spindle speed: max. 12,000 rpm Tool holder: BT 30 Number of magazine slots: 26 Travels: X-axis: 500mm Y-axis: 400m Z-axis: 410mm 4th axis: 0.001° Accessories: Nikken Rotary Table Base plate zero point clamping system We have 2 identical machines in stock.

Manufacturer: DONAU Model: DR 50 Find more here - .ucymachines/ Contact us at - sales@ucymachines

Offer 25032 Technical data: - Drilling capacity in steel ST 60 50 mm - Drilling capacity in steel ST 60 65 mm - Tapping device up to M 60 - Drilling spindle holder MK 5 - Drilling spindle stroke 240 mm - Projection 400 mm - Table with 2 T-slots 720 x 560 mm - max distance table – drilling spindle approx. 850 mm - 4 feeds 0.1 - 0.2 - 0.3 - 0.4 mm/rev - AZ continuously variable transmission with manual transmission - Drilling spindle speeds infinitely adjustable 40 - 1600 rpm - Drive 400 V / 5.5 kW - Space requirement approx. W 850 x H 2480 x D 1350 mm - Weight approx. 1450 kg

Cooling: air-cooled Control: Hot Gas Valve Control: Digital display Condensate separation: lossless, Level-controlled steam trap Performance data Nominal capacity at pressure dew point +3°C 0.6 m³/min Max. operating pressure 16 bar Total energy consumption (25°C input temperature) 0.16 kW Refrigerant R513A 0.17 kg Installation data Ambient conditions min. / max. 5 / 43 °C Pressure drop at full load 0.25 bar Voltage / Frequency 230 / 50 V / Hz Dimensions and weight Length x width x height 350 x 493 x 450 mm Weight 19 kg Compressed air connection G 3/4 "ag

1 of used dryig system, consisting of main assembly (hood with Tetra conveyor frame) with hood, Sonic Air Systems blower with Leroy Somer motor type 256TC / 3x 400 V / 50 Hz, 20 HP / 27.6 Amp. (with Danfoss VLT 5000 VFD in separate panel), and 3x Sonic Air Systems airknives each 3" body diameter and 610 mm slot length With manifold from 1 to 3 hoses. Hoses not available. Control panel not available (was switched from combined line conveyor control panel).

Three Broich conveyor belts are available, length conveyor belt 1/2/3: 4400/4070/5500mm, width conveyor belt 1/2/3: 1400/1900/1400mm. An on-site inspection is possible.

Key data: 100 mm, 1600 mm, 1120 mm

Spindle diameter ... 100mm Axis X ... 1600mm Axis Y ... 1120mm Spindle speed ... 0-1200 rpm Axis W ... 900mm Axis Z ... 1250mm Spindle mount... ISO 50. Clamping table surface... 1250 x 1250mm Max. table load ... 3000kg Main engine power ... 11kW L x W x H ... 6710 x 3450 x 3000mm Machine weight ... 14 000kg The machine is in good condition, possible to test under power.

This QUICK CNC KQ-62 Lite multi-spindle drilling machine was manufactured in 2025. It handles workpieces from 70 to 2400 mm in length, 9 to 60 mm in thickness, and 30 to 1220 mm in width. Features include a Higerman control system, dual 3.5 kW milling spindles at 18000 rpm, and comprehensive drilling units. Consider the opportunity to buy this QUICK CNC KQ-62 Lite multi-spindle drilling machine. Contact us for more information.

Key data: 22 , 8 , 2

Atlas Copco SF22+ Compressor Atlas Copco CD45+ Dryer Sold as a set. Oil-free air compressor Pressure: 8 bar Flow rate: 2.4 m³/min Power: 22 kW Weight: 687 kg Year of construction: 2024 As good as new Unused device All employees speak Dutch, German and English Prices plus VAT Shipping available for an extra charge (Subject to changes and errors in technical data, information and prices as well as prior sale)

LABORATORY MASTICATING TURBINE MANESTY ACCELACOTA, Pierced turbine with anti-surge (contre pales), Spray arm, For batch sizes of around 10 kg, Dimensions (mm): 1300x860 H 1650mm, Inner diameter (mm): 600, Depth (mm): 440, Perforated turbine: Yes, Batch size: 15kg, Perforated impeller: Yes, Weight (kg): 386

WORKING RANGE, Longitudinal (X) 1250 mm, Vertical (Y) 1000 mm, Transversal (Z) thread axis 380 mm, Drilling depth (V) 1000 mm, Drilling head inclination ( C) +/-20 °, Table rotation (B) 360,000x0.001 °, Workpiece approach (W) 500 mm, CNC, Measuring system optical scales, CNC SELCA 4040D, DRILLING UNIT, Min-max diameter from solid 5-40 mm, Spindle power 10 Kw, Rotation speed 4.200 Rpm, Drilling type gundrill, Drilling head inclination ( C) 40 (+/-20) °, FEEDS, X rapid 10 m/min, Y rapid 10 m/min, Z rapid 10 m/min, V rapid 10 m/min, TABLE, Surface 1000x800 mm, Resolution (B axis) 0.001 °, Static capacity 4.000Kg / dynamic 8.000 Kg, COOLANT SYSTEM, Tank capacity 650 l, EXTRA, Total installed power 30 Kw, Machine weight 17.500 Kg, Machine dimensions 5000x2600x3300 mm, Information about technical data are not binding., Machine available subject to prior sale.

Bicone dryer manufactured by LLEAL, model SBC-1400.

ID3738 Witte Bohrtechnik VSB500-200 year/Baujahr 1991 Trailer-mounted well drilling rig, Hatz engine, 2 hydraulic pumps, direct rotary head, with flushing pump (auxiliary pump) – with Hatz engine, previously drilled to a depth of 60 m – 160/170 mm Trailer well drill, Hatz engine, 2 hydr. Pumps, direct rotary head, with mud pump (auxiliary pump) - with Hatz motor, drilled with it so far: 60 m depth - 160/170 mm

Code: 0405 Brand: VITAP - ITALY Model: ALFA 21 Multiple boring machine for furniture, kitchens, custom furniture, bathroom furniture and various Technical data: N° 21 spindles - Centre distance mm 32 Max drilling depth mm 80 Table dimensions mm 860 x 500 Spindle rpm 2800 Motor power Hp 2,5 Tilting head 0-90° Operating pressure 6-8 atm Overall dimensions mm 950 x 800 x 1140 h Weight kg 300

Air dryer with vacuum conveyor, mounted on the injection unit or free-standing Drying of the plastic with hot air Hermetically insulated silo Capacity: 15l

Multi-spindle drilling machine manufactured in 2000. This SCM Morbidelli Zenith F2 is designed for processing flat materials such as DTD, MDF, laminated boards, and solid wood. It features a maximum working width of up to 3,200 mm and a maximum working height of approximately 800 mm. If you are looking to get high-quality drilling capabilities, consider the SCM Morbidelli Zenith F2 machine we have for sale. Contact us for further details.

Manufacturer: GEW Model: E2C Machine Type : UV Curing System Technical Specifications - Power output: 140 W/cm - Number of lamp housings: 9 - HMI control stations: 10 - Maximum lamp life: 2500 hours per lamp - Cooling: fully air-cooled, no water installation required - Condition: as new Find more here - .ucymachines/ Contact us at - sales@ucymachines

Multi-spindle drilling machine manufactured in 2019. This COMEC FMOV 1500 6UF + CA2 features a working width of 1500 mm and a working depth of 300 mm, allowing for efficient processing of long workpieces up to 1500 mm in one cycle. It includes an automatic parts loader and pneumatic clamping for enhanced productivity. If you are looking to get high-quality drilling capabilities, consider the COMEC FMOV 1500 6UF + CA2 machine we have for sale. Contact us for further details.

A bench drilling and tapping machine Ixion including automatic rapid traverse is available. Drilling capacity steel/cast iron: 15mm/14mm, tapping capacity: M3-M10, spindle mount: MK2, quill stroke: 90mm, reach: 215mm, column diameter: 75mm, speed: 1600rpm, table dimensions X/Y: approx. 220mm/285mm, weight: approx. 100kg. An on-site inspection is possible.

A heating and drying oven Horo is available. Connected load: 12.5kW. Max. temperature: 120°C. Heating power: 12kW. Volume: 2736l. Documentation available. An on-site inspection is possible.

Drilling capacity steel/cast iron: 50mm/60mm, spindle axis-column distance min./max.: 350mm/1600mm, spindle end-working surface distance: 350mm-1250mm, horizontal traverse: 1250mm, column arm vertical travel: 580mm, column diameter: 350mm, arm swivel: 360°, speed: 2000rpm, spindle travel: 315mm, torque: 392Nm, feed force: 15.6kN, machine dimensions X/Y/Z: approx. 2500mm/1250mm/3250mm, weight: approx. 3500kg. The coolant pump, the seal retainer and the measuring system are defective. Documentation available. An inspection on site is possible.

Max. Drilling diameter: 40mm, grinding wheel diameter: 200mm, grinding wheel width: 40mm, speed: 2800rpm, machine dimensions X/Y/Z: approx. 1200mm/850mm/1400mm, weight: approx. 350kg. Including cooling lubricant device and 10x spare grinding wheels. Documentation available. On-site inspection is possible.

Drilling depth: 60mm, min. workpiece width: 800mm, max. workpiece length: 2500mm, workpiece height range: 10mm-60mm, machine dimensions X/Y: 1400mm/1400mm, weight: approx. 750kg. Documentation available. An on-site inspection is possible.

Two brand new and unused Lenze gear motors are available. 1) Lenze GSS06-2, Power: 5kW, Speed: 1450rpm, Torque: 445Nm, Ratio: 20:1, Efficiency: IE3, Duty type: S1, Insulation class: F. 2) Lenze GSS06-2M VAR 112C22, Power: 4kW, Speed: 1450rpm, Torque: 444Nm, Ratio: 20:1, Efficiency: IE2, Duty type: S1, Insulation class: F. Documentation available. An on-site inspection is possible.

spindle diameter: 135 mm x travel: 3000 mm y travel: 2000 mm - Z-axis travel: 1600 mm travel -w axis: 700 mm TABLE: table-size: 2000 x 1800 mm table load: 10 t B-axis (table): 0,001 ° MILLING SPINDLE / HEAD: - spindle revolutions (max): 5 - 2000 U/min - spindle diameter: 135 mm - tool fixture: ISO SK 50: BT 50 TOOL MAGAZINE: - number of positions: 40 feed: 1 - 4000 mm/min rapid traverse: 8 m/min control: Fanuc 16i-MB total power requirement: 42 kVA weight of the machine ca.: 37,2 t dimensions of the machine ca.: 6,3 x 6,9 x 4,79 m equipped with: - CNC Control Fanuc 16i-MB - NC-Rotary Table 1800x2000mm - ATC 40-fold (BT 50) - COOLANT THROUGH THE MAIN AXIS - Chip Conveyor - CE The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm arm length: 1600 mm bore capacity in cast iron: 60 mm spindle diameter: 85 mm quill stroke: mm tool taper: MK 5 speeds: 24 - 1050 U/min feeds: 0,06 - 1,0 mm/U column diameter: 345 mm vertical adjustment of the arm: 900 mm thread cutting attachment: ja Boring motor: 5,5 kw total power requirement: 7,5 kW weight of the machine ca.: 4000 kg dimensions of the machine ca.: 2,5 x 1,0 x 2,99 m Radial drilling machine - Mounting cube 750 x 500 x 500 mm - Digital display for boom travel - Coolant system - Good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Technical data: Installed power: 0.58 kW Voltage: 380 V Spindle speed: max. 3000 rpm

taper MK: 2 : ja weight of the machine ca.: 200 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

taper MK: 1 bore capacity in steel (diameter): - mm weight of the machine ca.: 140 KG The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

spindle diameter: 130 mm x-travel: 6500 mm y-travel: 2000 mm z-travel: 900 mm W-axis (spindle longitudinal): 800 mm spindle motor: kW spindle turning speed range: 5 - 1000 U/min total power requirement: 30 kW weight of the machine ca.: 35,5 t dimensions of the machine ca.: - m - Spindle mount: SK 50 - Table size: 1800 x 2000 mm,10t - Angle head - Faceplate with faceplate slide U: 320 mm, - Heidenhain digital Readout, - Counterholder - 2 plate fields The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

spindle diameter: - mm x-travel: 1600 mm y-travel: - mm total power requirement: - kW weight of the machine ca.: 13,7 t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 8987 Type: WD 130 Producer: TOS Generated: Parameters: Maximum spindle speed: 2000 1/min X-axis travel: 6400 mm Y-axis travel: 2500 mm Z-axis travel: 430 mm Without a table.

FUJII SEIKI Heavy Duty Lathe (Japanese Origin) Technical Specifications: • Turning length: 2,000 x 26,000 mm • Modular bed • Capacity between centers: 60 tons • Drilling attachment included • Drilling tool length capacity: 12,000 mm Condition: Available Location: South America Machine suitable for heavy-duty machining of long shafts and large industrial components.

Save energy and water, Efficient surface drying, Compact, powerful drying system, particularly energy efficient, Optional: with tunnel system, Areas of application:, • Water carryover, • Bottle neck drying, • Blowing off crown caps / flip-top bottles, • Can level blow-off, • Coding area drying, • Blow off dust, • Blowing off residual water for camera-supported control, Compact design in different versions:, • Band attachment (approx. 500 x 500 mm), • Rack mount, • Wall mount, Technical specifications:, • Max. power consumption 1,300 watts, • 230V connection, • Infinitely variable, • Ambient temperature 0-50°, • Storage temperature –40 to +85°, • 220 m3/hour or 3,666l/minute, • Overheating/overvoltage protection, Suitable e.g. for:, • Bottles, • Cans, • Beverage carton packaging, • Glasses, • Bowls, mugs, • Vacuum packaging

x-travel: 780 mm y-travel: 560 mm z-travel: 560 mm total power requirement: --- kW weight of the machine ca.: 12,0 t dimensions of the machine ca.: --- m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Used machine Rows of holes Dowel drills Manufacturer: Ganner Type: Gannomat 120 Year of manufacture: unknown Power: 1.1 kW Working range: Drilling stroke: 120 mm

Number of spindles in row of holes: 11 Number of spindles horizontal: 3 Cup belt drill head: yes, Blum Drill pitch: 32mm Power consumption: 2.2kW

Year of construction unknown Dry pollinator Mediprint Powder duster for sheetfed offset suitable for Heidelberg SM 52 with original protection for display as good as new Delivery date: immediately from stock

Unused Servo Control for a Tetra Pak Cap 30 Flex. Tetra Pak article number: 90605-9390. Official Tetra Pak description: Servo-Antrieb, K5500 EtherNet/IP 528VAC., Type of Machine: Servo drive, CAT NO: 2198-H025-ERS, Instructions: 2198-IN001x-xx-x, MAC Address: 40:41:01:E0:74:10, Main input: 195-264/324-528 Vac 8.3 Arms 3 Ph 50/60 Hz, Control input: 24 Vdc 2.8A, Motor output: 0-460 Vrms 3 Ph 0-590 Hz 8 Arms Continuous, 20 Arms Peak

degree: - length: - mm width: - mm height: - mm capacity: - kg/h total power requirement: 30 kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

IXION AUERBACH TL 1004 deep hole drilling machine was built in 2004 in Germany by Ixion Auerbach Maschinenfabrik GmbH. The machine is designed for precision drilling of deep holes with a maximum depth of 1000 mm. Workpieces made of various types of material are machined fully automatically by means of precisely guided tools, which keeps the hole perfectly straight. All machining parameters are programmed in an advanced control system with many useful functions. The offer also includes an extensive equipment, consisting of, among others, a measuring probe, gun drills and a chip conveyor. The IXION TL1004 deep hole drilling machine weighs 3500 kg. Technical specifications of the IXION AUERBACH TL 1004 deep hole drilling machine - maximum drilling depth: 1000 mm - maximum hole diameter: 32 mm - minimum hole diameter: 6 mm - drilling capacity in 1.2312 steel (carbide gun drill): fi 25 ...

An Arburg plastic granulate dryer with integrated material conveying is available. Hopper volume: 100l, max. drying temperature: 150°C, heating capacity: 4.5kW, air capacity: 90m³/h, conveying height: approx. 3000mm, machine dimensions X/Y/Z: approx. 950mm/600mm/2000mm, weight: approx. 150kg. An on-site inspection is possible.

spindle diameter: 130 mm x-axis: 4000 mm y-axis: 2100 mm z-axis: 1500 mm w-axis: 700 mm spindle taper: BT 50 spindle turning speed range: 2500 U/min spindle drive: 22 / 26 kW table surface area: 1600 x 2000 mm table load: 12 t B-axis (table): 0,001 ° feeds longditudinal/cross/vertical: 5000 mm/min rapid motion -longitudinal/cross/vertical: 15 / 12 / 15 m/min Control: Fanuc 0i MF total connected load: kW weight of the machine ca.: 35 t dimensions of the machine ca.: 7,5 x 6,7 x 4,5 m Equipped with: - FANUC 0i MF (10.4” LCD) - Data Server + AICC II - ATC for 60 Tools (BT 50) - X/Y/Z axis THK roller linear guide way - X/Y/Z axis Haidenhain linear scales - Coolant thru spindle 40bar - Spindle oil cooler - Hydraulic cooler - Air conditioner - Chip conveyor Operating Hours: 14761h Cutting Hours: 4382h The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ...