intermeshing mixer, GK-110-E, Fabikat Werner & Pfleiderer, hydraulic hopper, uni-drive gearbox 630 KW,(Motor AC Siemens 585 KW + Siemens Frequenzumrichter G-150 New 2016)
Bieffebi press 30 ton Hand-operated hydraulic press with 30 tons of pressure Upper and lower plate heated to 210 ° C, separate setting of the TemperaturTischgröÃ?e 300 400 mm SchiebeplatteZum manufacture of pressure scenes or vulcanization of rubber parts.
Mesh belt for AUMA / Rotocure new and unused Length: 14100mm Width: 2250mm
Reference No.: 75181001 Engine type: slicer specification: cross Strip cutters, reconditioned Cutting width: 800 mm max. Cutting height: approx. 20 mm Cutting force: approx. 10 to Drive: 1.8 kW - 400 V - 50 Hz Safety devices up to date New control box Incl. CE mark, 1 year warranty With operating and maintenance instructions in English
available Bersorff Rotocure Drum diameter: 900 mm Working width: 1400 mm Machine was overhauled recently. Description in annex!
QTY 1 x Pomini VIC1.8-PX1.6 Tandem Lab mixer, Machine number 9912, date 1990, Modern frame design with unitized fabricated steel base, Anti friction roller bearings with floor lubrication, 22kW DC variable speed motor. Rotor speeds 0-230rpm Torque montioring sensors. Siemens PLC control system with S7-300 CPU (combined with original S5). Desktop computer interface. Left hand mixer: Pomini PX1.6 tangential rotor type, Volume 1.6Litre, 2 wing rotors, FY type bronze dust seals, Jacketed chamber for ...
Shaw Almex Repair Press Platen Size : 2200 X 3200 Crocodile opening No Of Platens : 2 Nos No Of Day Light : 1 Nos Working Hyd. Pressure In PSI : 200 12-14kg per cm Heating Medium : Steam Type Of Press : Bladder Type Belt repair Press suitable for mattings / sheeting Approximate weight : 18 Tons
Francis Shaw Rotorcure Main Drum Diameter : 60” / 1524MM Main Drum Width : 1575MM Bottom Drum Width : 1530MM Top Drum Width : 1525MM Pressure Drum Width : 1525MM SS Belt Width : 1430MM Belt Thick : 1.8MM For 2-3mm up to 20mm thick sheet Steel belt Make : Francis Shaw Heaters Type : Electrical Heater Quantity : 3 set x 4Nos Heater Capacity : 1.6KWEach Motor HP : 35HP APROXIMATEWEIGHT : 80 Tons With Winder Let Off Status : Working condition
Oven Type: GAS HeatedApplication: Composite Curing.Work Chamber Dimensions: Height: 2.1m Width: 3m Length: 6mThermal Insulation: 125mm thick mineral wool insulation throughout.Operating Temperature Range: Normal process temperature up to 200 Degrees C.Maximum safe design temperature: 250 Degrees C /- 3 deg C within the airflow envelope.
4-rollers used 200 x 450 mm - calender Roll diameter: 200 mm Roller hole: hollow Number of cylinders: 4 Electric control: conventional protection control, control panel for settings of speed and gap adjustment Strip cutter: 2 blades, circular, manual width adjustment
MIR Horizontal Injection Moulding Machine Type: MPO 135/500 Year 2000 Mould thickness 60mm Screw diam. 50mm Theoretical Injection capacity 412cm3 Injection rate 175cm3/sec Injection Pressure 1480 bar RPM screw rotation 240 min-1 Cylinder heating power 10.5kW Temperature control zones 3 = 1 n Approaching carriage force 45kN Clamp unit Mould closing force 1335kN Moving platen stroke 520mm Max. daylight between platens 720mm Mould height min-max. 200mm Platen dims. H x L: 640 x 640 mm Distance betwee ...
Qty 1 x Carter MK6 direct drive Banbury internal mixer, Serial no. 237/11 (New chamber/hydraulic hopper in 2011/12), Hydraulic hopper, Chamber volume: 160L, 2 wing rotors, SSA type dust stops, hydraulic drop door with linear actuator, pneumatic oil injector fitted to end frame, hydraulic hopper, PIV semi unidrive gearbox (28:1 ratio), 310/620kW power rating, 728/1484rpm input speed, 26/53rpm output speed. Currently fitted with fixed speed motor fitted - 355kW, 744rpm to give rotor speed 26.5rpm. Complete ...
Manufacturer: Wickert Press new in 2000 Closing force 2000kn Platen size 560mm x 630mm Daylight gap: 300mm Type of heating; electric Completely overhauled in 2005 The machine is in top quality with CE marking With vacuum chamber and sliding table
Francis Shaw Pin Barrel Extruder Screw diam. 90mm LD ratio 16:1 Roller feed Barrel jacked / pinned Clamp swing bolt DC drive motor 63kW 1750rpm 45volts, 3 phase, 50 cycles Complete with Panel and 4 x temperature control units
- chamber volume: 73dm3 - input volume: max 50dm3 - chamber fulfillment: 0,7 - rotors RPM: 30/34 RPM - chamber friction: 1 - 1,13 - main drive power: 200kW - power of the installation for supporting drives: about 3kW - mixing cycle duration: 6 to 12 minutes - standard efficiency: 400kg/hour - protection from wear - hard alloy welded on working surfaces - cooling: water-cooled through nozzles - bearing: roller bearings - bearing lubrication: central lubrication with solid state lubricant Overhaul took ...
Used 3 rolls rubber calender Berstorff from the tireline. rolls dia. 2 x 300mm middle roll 250mm rolls overall length: 700mm working length: 500mm main motor power: 51,5kW Middle roll is designed for shaping covers application.
Mixing chamber capacity: 155l, nominal capacity: 110l, drive power: 250PS, drive shaft rotational speed: 100/min, blade rotational speed: 19.2-22.6/min, stamp pressure: 2kg/m², operational pressure: 8at, compressed air consumption: 25-40m³/h, coolant water consumption: 15-20m³/h, gear pump output: 150l/min.
FOUR ROLL CALENDER MANUFACTURER: COMERIO ERCOLE YEAR OF MANUFACTURER: 1962 CALANDER TYPE: 4 rolls calander inverted L (CG-L-4/610X1600) ROLLS SIZE: 1600mm x Ø 600mm ROLL TYPE: of chilled , cast iron hardened LINE SPEED: 6 – 36 m/min CROSSAXING DEVICE third roll RATIOS BETWEEN ROLLS from 1:1 to 1,5 (50%) GEAR BOX: 4GS-3N-920 (Salzgitter Maschinen Aktiengeselschaft) POWER OF THE DRIVE MOTORS 4 d.c. motors with shunt characteristics 37 kw (1460 r.p.m)
Cylindrical Grinder Swing 250mm (it can take up to a 500mm roller) Travel approx 8ftMade for grinding rubber and polyurethane rollers Complete with:• Hydraulic cylinder • Power pack• Internal attachment• Study rest• Coolant tank• Control panelWorking and in good conditionWeight: 6-8tonne
1 x Heavy duty 2 roll mill Roll dimensions: 2100mm x 665mm dia. Hydraulic nip adjustment, Safety push bars, Peripherally drilled rolls, Sleeve bearings with grease lubrication, Right angle drive gearbox, with Siemens 240kW DC variable speed motor, Strip knives fitted to front roll, Heavy duty fabricated bedplate, Carter stockblender mounted on top.
1 x Refurbished Pomini Farrel model P160 Banbury internal mixer, Original year of manufacture 1984, Rebuilt in 2017 (not used since), Mixing chamber volume 160L Net, Batch size at 75%FF and SG 1.0 - 120kg, 2 wing rotors, PYH hydraulic dust stops (new), hydraulic drop door discharge with linear actuator and spade latch, Pneumatic hopper, Unidrive gearbox type NF160, rating 640HP, Input speed 1500 rpm, output 39.6rpm. with 470kW, 500V DC variable speed motor. Mechanically complete but currently without ...
Quality Seal diameter: 40mm Max seal: 180mm
4-roll calender 150 x 400 mm Roll diameter: 150 mm Roll length: 400 mm Dimensions: 2250 x 1780 x 1570 mm (L x W x H) Weight: 2300 kg Motor: 9 kW Machine is designed as a 3-roll to 5-roll calender (4 rolls available).
Cryo deflashing machine Chamber 60 l
Roll mill 650 x 2100 mm - used Model external gearbox, external motor mounted laterally on the machine Cylinder diameter 650 mm / roller length 2100 mm Cylinders peripherally drilled hydraulic gap adjustment new Hydraulic unit new tilting guide plates Cylinders mounted on roller bearings with oil lubrication Cylinders with new rotary joints for connection to water circuit Safety brake for emergency stop AC motor 160 kW - 380 V - 50 Hz Mill tray to contain the compound bi directional safety system Dis ...