cpm pellet press used for sale

For sale complete plant for wood pellet production, made from CPM, capacity 6t/h. A most of the maschines from line are produced in between 2008-2010.y., except presses for making pellets (its bit older then rest of the line, but completly renewed before restarting. Line is consisting from: 1.Chain conveyer for logs transport. 2.Lift with angle platform for dosing material. 3.Entrance belt transporter with magnetic section for detection of iron. 4.Grinder (hammer mill) BRUKS 500kW 5.Verticaly basket transporter for chip wood. 6.Horisontal belt transporter for chip wood with three side ejectors into depoos (separated with type of the wood) 7.Hidraulic floor platform for dosing wood chips (three pcs.) with all instalation and system of hidraulic pistons. 8.Horisontal belt transporter for transportation material on drying. 9.Repler transporter for driving wood chips into fire plac ...

Freshly revised Koller to CPM Press 3022 or 7022 Punched, 2 new bearings, new sleeve, new intermediate ring, filled with grease. rest used. Koller are no longer needed due to machine changes. 3 pieces Available

Freshly Revised Koller to CPM Press 3022 or 7022 , Fshbone, 2 new bearings, new sleeve, new intermediate ring, filled with grease. rest used. Koller are no longer needed due to machine changes. 3 pieces Available

Collier sleeves Fishbone CPM 16-2.5

Collier sleeve Fishbone CPM 22-2.5 for pellet press

Complete pellet line for biomass or animal feed. CPM 3020-4 with 132 kW motor Including CPM Conditioner, CPM press and Geeelen cooler with fan and cyclone. Positive direct gear drive 132 kW, provides a 98% energy transfer Rounded cast gear case with internal ribbing for quieter operation Segmented die clamps for quicker die changes Metal-to-metal seals between components Modular gearbox design for production flexibility Replaceable quill flange Stainless steel pellet chamber Single motor 132 kW for greater efficiency Very good condition.

Pellet mill / press CPM 7900 aftre renovation Dia inch : 30 - 762 mm Die width : 8 - 210 mm Die surface 5025 cm² KW : 250 KW Machine type : 7900 Buildyear : 1984 Width rollers : 215 mm Dia rollers : 350 mm 1 set rollers Oil cooling Twin mixer 2 x 15 KW / Die Hosting system New inlet in stainless steel

Used SHREDDIES production line Manufacturer: CPM WOLVERINE PROCTOR Ltd. Model: 5-station SHREDDIES production line Year: 2016 Description: A five-line production line for multilayer flakes from crushed grains. Finished product capacity: 700 kg / h Line speed: 54m / min. Finished product density: 200> 220 g / l Overall dimensions and setting of the machine: length x width x height: approx. 10929 x 1600 x 4685 Design diameter of the grinding roller: 203 mm Design working width of the chopping roller: 210 mm Rotational speed of the grooved roll: 20-85 m / min. Design number of positions: five (four working, one spare) Design width of cutting station conveyor: 230 mm Nominal design width of the edge trim: 12 mm per edge, total 24 mm Design product size: approx. 25 x 25 mm Technical data: Dimensions (length X width X height): Power supply: 400 V, 3 phases, 50 Hz Control v ...

Jetzone furnace Manufacturer: CPM WOLVERINE PROCTOR Ltd. Model: SND 1.5 x 202 Year: 2016 Productivity: 450 kg / h Dimensions: 8136 x 3581 x 4376 Heating medium: natural gas Description: A high-speed dryer consisting of two main elements: a fitting equipped with heating and distribution elements, and a production conveyor.

2 pcs clamping jaws 22" / Die Clamp Segment Assy 22" for pellet mills CPM 7722-2 and CPM 3022-2 Plus Transportation

Assembled Knife Holder for CPM 7930 Model 30-4 Knives included

Water flow rate 30-150l/h Flow meter with manual control valve Solenoid valve for water and compressed air. Pressure regulators for water and air Special nozzle for injecting water and air Mounted on a plate

General SKU303P611 LocationBarneveld MakeCPM Wolverine Proctor (UK) TypeVariable circulation lab dryer No.L 09091 Year of construction2009 Main Features MaterialStainless steel Volume900 Ltr. Max.temp.250 °C Specified Features - Drying oven Drying ovenvariable circulation laboratory dryer Max. temperature250 degr.C Number of compartments:1 Capacity900 Ltr Internal width800mm Internal depth1030mm Internal height1100mm Steam heatingcheck Number of doors:2 With air circulationcheck With fan(2x) Motorcirculation fan 2,0 KW, Motor exhaust fan 3,0 KW With air humidificationcheck With trays(4x) 762x508x102 28% perforated MaterialStainless steel Information With switchgearcheck Weight2000 KG CEcheck Floorspace2,8x2,2 M Extra Specificationsheat exchanger : Heap Dawson Limited, Serial 6744, PS 10 bar, max 250 degr.C. Drying ovensCPM Wolverine ProctorDryers > Dryi ...

Switched-mode power supply, electronic module KNIEL CPM 100/VME ( CPM100/VME ) 330-049-04 Input: 110 / 220 V AC 45 - 440 Hz Output: 5 V DC 12 A 2 x 12 V DC 2.0 A used, tested ! Dimensions: 190 x 70 x 130 mm

machine Saf-fro Oxytome 25 for sale equipped with: two Harrison gas burners Saf-fro CPM360 plasma torch with Nertajet HP300 source and the Friojet cooler - 30 plus the Mark MDX900 air dehumidifier.

l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

Pellet heating, pellet stove, biomass stove used. Manufacturer: ELMEC Group Srl Type: B-MAX 300 EBBR020300-P01 Year of construction: 2018 Burner power max. 300 kW Nominal power 250.2 kW Max water temp. 90°C Boiler dimensions: approx. 1700 x 1100 x 1650 mm Additional burner approx. 1000 x 500 x 900 mm Pellet hopper approx. 800 x 800 x 1200 mm + auger Subject to changes and errors in the technical data, specifications and prices as well as prior sale.

Pellet mill for ring DIE and two roll shell system. Inside diameter: 900 mm Active operating width: 138mm Active forming area: 3902 cm² Press roll Ø440/142 optionally dimpled or notched Front door Stainless steel front door with large opening angle. pneumatic operated overload bypass protection gate. Two knives with step less length adjustments integrated in the door. Machine housing All housing parts are cut by precision laser. The machine base, the base plate and the housing are welded and reinforced. Drive Drive via 355 kW-1200 rpm engine , timing belt Ø200/1900 - Beltdrive Motor and Motor cables not included. Equipment Central lubrication for roll assembly and main shaft Manual roll adjustment Overload protection provided by a safety pin Die of chrome steel X46 Cr13 with conical seat for an easy change of the die - Die is not included Adjustable defle ...

Wood pelletizing plant, KAHL pellet press used the complex includes: Pellet press AMANDUS KAHL Matrice diameter approx. 1000 mm Pallet diameter approx. Ø 8 mm 5 Koller approx. Ø 340 x 130 mm Motor power 160 kW an auxiliary motor is damaged, but can be replaced by us Dimensions approx. 1600 x 1800 x 3000 mm + motor Weight approx. 8000 kg Conditioner / Dosing and Mixing Screw Diameter approx. Ø 400 mm 5.5 kW Dimensions approx. 3100 x 900 x 800 mm Single shaft paddle mixer Dimensions approx. 3300 x 1600 x 2000 mm + gear motor Pellet coolers Dimensions approx. 2300 x 2300 x 3000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.

L 45 Kw POWER 680 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw

L 30 Kw POWER 450 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 30 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw

l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

Graf Kollerhülsen Geriffelt to CPM Pelletpress

Graf Koller sleeves punched for CPM 16-2.5 Pelletier press

Koller sleeves Geriffelt for CPM 22-2.5

Koller sleeves punched for CPM 22-2.5

For sale is a functioning pellet production line including controls. The plant is suitable for pelletizing agricultural raw materials (straw/hay/alfalfa etc.) and has an output of 1000-1600 kg/hour depending on the material. The complete system has approx. 800 operating hours The production line is composed of: cjffolp2bh Byfo0wxd Bale breaker 37 KW + bale conveyor table 10m and Hammer mill 75 KW Zyklon + Rotary Valve + Buffer Tank Scheuch dust filter house with control system and a capacity of 20,000m3/h including discharge for big bags, 2 Koller ring matrices pellet mill 110 KW with aut. Central lubrication. In the associated conditioner, the moisture content of the material is automatically controlled by means of a dosing pump and mist nozzle as well as a microwave sensor from the Envea brand. Pellet cooler with level sensors and automatic emptying. Vibrating scr ...

L 22 Kw POWER 330 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 22 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw

Pellet press 3-5 tons hour 2006 but very little used of the brand PTN 1100 150-300 Dutch make very very sturdy and very good condition with some spare parts, sale due to project dissolution

This press from Collin at Plastima Used Machinery in machine storage. The machine is from 2001 and is in good condition. – Brand: Collin Pilot & Lab Solutions – Model: P200P – Construction year: 2001 – Plate Size: 200 x 200 Mm – Max. pressing force: 196 kN

Pellet Production Plant Capacity per hour: 4 tons -Moving floor -Conveyors -Chips heating system -Filter system -Sieve plant -Dry hammer mill -Pellet mill -Pellet loading system

We sell our until recently used pellet press, incl. control cabinet, drive press 2 x 22 kW, incl. conditioner and dosing unit frequency-controlled, incl. second set of roller wheels and various dies from Ø 4-8mm, built-in dies: 4x40 for animal feed; approx. 3500 kg/h feed - possible depending on input material

We sell our LAMEC 520, which was in use until recently, with die quick coupler; Drive press: new motor 1x 75kW with 1450rpm + alternatively 1x 110kW with 985rpm for biomass, incl. 2 pcs Pcs conditioners and 2 pcs dosing units frequency controlled; Control with star/triangle combination for 75kW motor, incl. several roller wheels and various dies; built-in die 4x40 for animal feed,

Counterflow Cooler, Model VK19X24ML with Rotary Feeder Valve. Hood and walls performed in stainless steel. DIssambled and ready to ship

Sprout Matador Feed expander. Comes with 250kw motor and feeding conditioner.

Sprout Matador PM 1219 with 400kw motor 3 press rolls

PTN Pro 900x228. Complete with conditioner and 250kw motor Hydrulic rolls adjustment

Capacity 3 ton/hour Motor power 200Kw Die diameter 1000 mm Number of rollers 5

The pellet mill has been refurbished by us and is in as new condition. Die, roll assembly and V-belt are new. Engine power 2 x 110Kw The diameter 650mm Press width 105mm

Dimensions 2,0 x 1,2 x 1,55 m Grindstone diameter 250mm Diameter of matrix 1,2m Grinding cross Movement 200mm Grinding longitudinal Movement 450mm Consumable power3kW Grinding thickness of the matrix per cycle - 1/100 mm or 4/100 mm. The required number of cycles is adjustable. Electrical connection of the unit - 380V, 50Hz, 3 phases. Weight 545 kg

Dimensions 1,6 x 1,4 x 1,44 m Grindstone diameter 250mm Diameter of rolls 0,13 … 1,1m Grinding cross Movement 200mm Grinding longitudinal Movement 450mm Consumable power 3kW Consumable power 3,5 kW Electrical connection of the unit - 380V, 50Hz, 3 phases. Weight 545 kg

General SKU231U198 LocationBarneveld MakeRieter TypePRIMO 100 S No.10.0069173 Year of construction2006 Main Features Motor3 KW Width100 mm Specified Features - Pelletiser MaterialMild steel Pelletiserstrand pelletizer Rotor width130mm Rotor diameter100mm With roll feedingcheck Motor3 kW 220-240/380-420 Volt (598 rpm) Capacitymax 350 kg/h Outlet200x140 mm Information Mounted on framecheck Mounted on wheelscheck With switchcheck Weight750 kg CEcheck Floorspace1,3x1 m Total height1,45 mPelletisersRieterMills > PelletisersBrand > Rieter What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU231U190 LocationBarneveld MakeRieter TypePrimo 100S No.10.006-8519 Year of construction2000 Main Features Motor3.5 KW Width100 mm Specified Features - Pelletiser MaterialMild steel Pelletisercheck Rotor width130mm Rotor diameter130mm Number of rotor knives1 Motor 3,5 kW, 400 volt Number of strands:4 Capacity30-90 kg/min Outlet200x140 mm Information Mounted on framecheck Mounted on wheelscheck With switchcheck Weight620 kg CEcheck Floorspace1,3x1 m Total height2,2 mPelletisersRieterMills > PelletisersBrand > Rieter What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU063S235 LocationBarneveld MakeScheer & Cie TypeHSG400 No.21057927 Year of construction1990 Main Features Motor22 KW Inlet diameter200 mm Width400 mm Specified Features - Pelletiser Motor22 KW, 380/660 Volt Information Mounted on framecheck Mounted on wheelscheck Floorspace1,0x1,6 M Total height1,7 M Weight1200 KGPelletisersScheer & CieMills > PelletisersBrand > Scheer & Cie What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Stock number U1984-2 Used impact dryer for pellet by RIETER (Germany) model AERO 500 in stainless steel design (material 1.4541, AISI 321). Dryer is equipped with air blower providing 90 m3/min and driven by electric motor with power 18.5 kW. Dryer has reported output 4000 kg/h of outgoing product. Flow rate of water with pellet: 35 m3/h (maximal), 25 m3/h (nominal) and 20 m3/h (minimal). Nowadays machine has installed screens with mesh 1.2 mm. Machine new 1997. Shipping dimensions of dryer: width 1400 mm x length 3830 mm x height 2265 mm. Weight of machine – 700 kg. Body of drying chamber is sound-muffled. Technical documentation included in german language. Machine had been working on PP pellet.

Stock - No.: 1820 1 used, overhauled CUBE DICER as type Sagitta - LANCELIN BG 200 working width 200 mm drive 7,5 kW – NEW cutting tools 4 x 4 x 3 mm cube pellets incl. pneumatic infeed roller system More pelletizing equipment ex our stock Wuppertal Germany available, Ask for our most recent stock-list or visit us

Stock - No.: 1624 1 piece used strand pelletizer PREVIERO > adjustable cutting length type TA 200 NA year 1996 – partly overhauled in 2020 drive 4 kW + 0,37 kW 200 mm cutting width new control board FU controller We have more strand-pelletizers, waterring or underwater pelletizing units available ex stock Wuppertal Germany, You´re welcome to visit us. Please find our stock-list on the Homepage: plastictrading

No.: 2324 1 used strand-pelletizer Alphatec type AS-G 200 E year 2019, very good condition - lab / demo use only working width: 200 mm drive 7,5 KW – AC frequency controlled cutting rotor with hard-metal teeth pneumaticm pressure roller device Machine is ready for demo. More strand-pelletizer ex our Stock available: Scheer, Automatik, Rieter, IPS, AlphaTec, Pelltec, .. Our actual machine stock-list you can find on our Homepage: plasticotrading.de