concrete cut used for sale

Wire diameter range: 4.0 - 10.0 mm section sections: up to 4,000 mm feed speed: 90 / 120 mtr./min; ready for use

wire diameter range: 4,0 - 10,0 mm cutting length: up to 4.000 mm wire feeding speed: 90 / 120 mtr./min; ready for operation

Wire diameter range: 8.0 - 12.0 mm section slats: max. 5,550 mm feed speed: 70 - 100 mtr./min directional fluegel with hyperbolic rollers; good

wire diameter range: 8,0 - 12,0 mm cutting length: up to. 5.500 mm wire feeding speed: 70 - 100 mtr./min. Straightener with hyperbolic rolls; good

Wire diameter range: 1.5 - 7.0 mm section sections: max. 2,000 mm feed speed: 5 - 120 mter./min. machine has been completely repainted; very good

Vertical Bevel-Cutting Machine Manufacturer: Hyma Model: VSL.A.75 Manually operated roller table with aluminium covered table-too Hand-wheel operated rest-plate with ratchet mechanism for repetitive cutting of same width: 0-130mm Inclinable cutting section with four dynamic balance blade-wheels, each suspended between two adjustable bearings Motorised angle-adjustment for cutting section: +/- 60 degrees. Electric blade drive motor Twister double-edge ground bank knife for cutting in forward and reverse movement of roller table Blade tension control with indication lamp and automatic cut-off on blade slackness and breakage Manually height-adjustable blade guard and fine-adjustable blade guide rollers above and below table Friction grinding apparatus with two adjustable cupstones Electrical control box mounted on table front, adjacent to operator Standard dimensions: Cuttin ...

wire diameter range: 1,5 - 7,0 mm cutting length: max. 2.000 mm wire feeding speed: 5 - 120 mtr./min machine is been complete new painted; very good

Wire diameter range: 1.0 - 4.0 mm section sections: max. 2,000 mm feed speed: 5 - 90 mtr./min.; ready for use

wire diameter range: 1,0 - 4,0 mm cutting length: up to 2.000 mm wire feeding speed: 5 - 90 mtr./min; ready for operation

M. No.: 20051619 Basic Functions: Slit, Cross cut, Crease In-feed paper size: 210(W)x210(L) to 370(W)x520(L)mm Minimum finished size: 55(W)x45(L)mm Paper weight: 120 to 400gsm Depending on paper quality Operation: 4" Touch Screen Job memories: 263 preset jobs & 150 customized job memories. (100 MANU SET + 50 FLEX MODE) Feeding mechanism Upper belt tri-suction suction feed (Patented) Side blower Skew adjustment Side aligner Double feed detection Cut mark registration Feed tray stacking capacity: 100mm Speed 8.8 sheets / min. : SRA3 21up business card 11 sheets / min. : SRA3 8up post card 12.2 sheets / min. : SRA3 4up greeting card 15.4 sheets / min. : A4 2 cuts & 1 crease

Combined cut-out machine and sheet metal scissors with base ; Very good

Working range: 1.5 x 3m, or 2 x 4m Standard equipment: self-focusing cutting head 2kW laser, cooling unit, cleaning and drying air system,safety cabinet, automatic twin transfer table,CAD/CAM software (Lantek, Metalix, Almacam)Control device with 15 touchscreen,foerderband,warning light,duesenset Options: linear drive technology, laser light source optional with 3, 4 or 6 KW removal device, safety light barrier,air conditioning for automation panel. 24 months manufacturer's warranty The price refers to a 1.5 x 3m system with 2 KW; ready for use

Plasma and cutting machine Promotec Ector 30 / 170 Working range: 3000mm x 17000mm 1 x Plasma Ht 2000 Hypertherm cutting up to 25mm 1 x Autogen support up to 100mm machine to visit under power . Without table and filter assembly and commissioning on request; ready for use

Semi-automatic short-threaded cutting machine for the production of external and internal thread Gr. via cross slide: 160 mm Gr. via cross slide guide: 240 mm tip wiete 250 mm nSpindle=180-2240 rpm spindle bore: 61 mm gr. threaded length/deep 100/6 mm

CO2-Laser, Bystar 4020, 4.4 KW Table size 2000 x 4000 mm, axis incl. interchangeable table, incl. suction, Bj.: 2004 ; ready for immediate use

Knife Corta K 1500 / 2000 Photooptic cutting machine working area 1500mm x 3000mm cutting with propane or aceethylene under current.; ready to use

Technical data in image

Sato Satronik C 1500, Y.O.M. 98Control 801Travel distances 2500mm x 1500mmSuction table Kemper 3000mm x 1500mm, Y.O.M. 2012Extraction Kemper 8000, Y.O.M. 2012, but with 0 operating hours, for outdoor installation, with portable control panel, plasma source Hypertherm Powermax 1650,laptop with laptop with Lantek programing softwareAssembly and commissioning on request; ready for immediate use

IFB (integrated flying bridge) Working area: 1200mm x 2000mm (real 1210mm x 1990mm) Table is 1400mm x 2040mm Operating hours: approx. 17.000 h Pump: Model: ESC Allan Lickiss, power 4150 bar The machine can be changed on Abrassiv cutting (other cutting head), all parts are almost unused. The machine was used exclusively for pure water cutting. ; ready to go

Microstep Oxycut A 4501.20 Working range: 4500 x 2000 1 Oxygen support: cutting up to 100mm including Cad/Cam system including suction system plasma operation prepared on request assembly and commissioning on request; ready for immediate use

This machine is particularly suitable for the processing of electrical waste with PVC and rubber. Diameter range 2 - 115 mm Cutting speed 35 meters per minute Weight 350 kg

Esab UXD - P 2500 Control NCE 290 1 x Plasma: Kjellberg PA S 40 cut up to 30mm 1 x Autogen Support Working area: 2500mm x 3500mm Including suction machine has two-sided drive and is very well maintained. commissioning on request ; ready for immediate use

; ready to use

Plasma cutting system with Hypertherm HPR 130 with automatic gas console cutting up to 20 mm Work area: 1500 x 3000 mm included filter system available under current mounting and commissioning on request

digital display swingdiameter over bed 800 mm swingdiameter over slide 600 mm distance between center 2000 mm spindle speed750 1 / min multifix tailstock

Technical data: Motor power: 0,75 kW Voltage: 220 V / 50 Hz Machine width: 900 mm Machine height: 1150 mm Machine length: 750 mm Weight: 135 kg Year of construction: 1996; ready for use

TH 3309 Control and spindle lathe Fixed bezel D = 19-70 mm Revolving bezel D = 16-50 mm LED machine lamp Reduction sleeve MK 3 / MK 5 Motor protection switch Emergency stop foot operated Engine: 400V 1, 5 kW 50 Hz Tip height 156 mm Top width 830 mm Spindle speed 60 - 2000 min-1 16 levels Spindle cone MK 5 Spindle bore D = 38 mm Weight 430 kg Dimensions Lxwxh: 1685 x 745 x 1320 mm G & PIECES 3402030

Fine beam plasma cutting system HD 3070 with manual gas console incl. Arcwriter Hose package plant suitable for 3 m x 8 m

Water jet system Flow Model IFB2 3618 TC 1P Year of construction: 2005 Condition good (used) operating hours 25000 h IFB2 3618 TC 1P UP 50iS Cooling Working area 3600mm x 1800mm high pressure pump 50iS-60ESL 4150 Bar With abrasive Without program software Available immediately . Installation and commissioning on request

Bystar 3015 5.2 KW Hours of operation: 30.100 h (stand 11.04.2017) Cutting hours: 10.760 h (stand 11.04.2017) Year of construction: 2004 Available from: August 2017

Water jet system flow model IFB2 3618 TC 1 P Year of construction: 2005 State good (used) hours of operation 25000 h IFB2 3618 TC 1 p UP 50iS cooling working range 3600 mm x 1800 mm High pressure pump 50iS 60ESL 4150 bar with Abrasivbehaelter without any program software Immediately available. Installation and Setup on request

Section 0.61 .. 0.68 length of 1.6 m width 3.10 m length operating range: 1,5 m x 3,0 m 700mm high sided suction scope plasma 24 months warranty; new

Manufacturer: MicroStep Type: SPL-PA 3001.15+S500 Working range: 3000 x 1500 mm + 500 mm shaft technology: plasma built in 2006 Kjellberg HiFocus 160i with autom. Gas console; (see PDF) 2 x additional quick-release co-buttons PerCut 170 Div. Wear parts Donaldson filter system including disassembly and delivery within Germany. Commissioning on request.

Pressure atmospheric maximum: 4000 bar X - axis: 3000 mm Y - axis: 2000 mm Sheet thickness: 0,00 mm Number cutting heads: 0   CNC Brand: _Unknown / Other CNC Model: Flowcut FLOW - MACH3 3020B CNC Waterjet 3000 x 2000 x 4000 Bar MACH - ID 6372 Make: FLOW Type: MACH3 3020B Control: FLOWCUT YOP: 2013 Hours: 3000 Working area X Axis    3.000 mm Working area Y Axis    2.000 mm Working area Z axis     178 mm Power resonator            4000 bar kW / Amp Feed rate X-Axis           12.700 mm Feed rate Y-Axis            12.700 mm Feed rate Z-Axis            12.700 mm Control            FLOWCUT Cutting hours     3000 H Linbear straightness a ...

Plasma cutting system with Hypertherm HPR 130 with automatic gas console Cutting up to 20mm Working range: 1500mm x 3000mm inlusive filter system Immediately available under current assembly and commissioning on request

CNC plasma cutting system Work area: 1500 x 3000 mm OTC Super plasma 12000 Cut quality cutting up to 20 mm New control ProDNC from Micompan Data transfer via USB

Power: 4 kW X - axis: 2520 mm Y - axis: 1550 mm Number laser heads: 0   CNC Brand: Fanuc CNC Model: 160i-L AMADA - LC 2415 A3 CNC Laser cutting machine 4kW 2500 x 1500 mm MACH - ID 6348 Make: AMADA Type: LC 2415 A3 Control: Fanuc 160i-L YOP: 2004 Hours: 11753 Working area X Axis    2.520 mm Working area Y Axis    1.550 mm Working area Z axis         300 mm Table Length          2.550 mm Table Width            1.550 mm Power resonator      4 kW kW / Amp Feed rate X-Axis      80,000 mm Feed rate Y-Axis      80,000 mm Feed rate Z-Axis      80,000 mm Sheet master loading arm     Yes Sheet tower storage        Yes Dust collector  ...

Knife Cortina plasma and burning cutting unit 1 x PlasmaSupport Hypertherm HD 3070 1 x gas support Working range: 2500 mm x 4000 mm electrified operation on request

CNC plasma cutting system knife Metalmaster working range: 8000mm x 2500mm Plasma: Hypertherm 260 Cutting up to 32mm very good condition immediately available with Donaldson filter system Including Cad/Cam software commissioning on request

control Mitsubishi CNC travel X/Y/Z 500/350/300 mm max. workpiece weight 800 kg table size 780x630 mm

CNC plasma cutting system blades Metalmaster Work area: 8000 x 2500 mm Plasma: Hypertherm 260 Cutting up to 32mm very good condition with Donaldson filter system now available Including CAD/CAM software commissioning on request

CO2 laser Bystar 3015 4.4 Kw, Table size 1500 x 3000 mm, incl. changetable, without loader, without suction, Y.O.M. 2006 glass revision in November 2015 under power laser: 28,000 h power on demand

Microstep - EuroCut-P 3001.15 Working range: 1500mm x 3000mm plasma source Kjellberg HiFocus 160i with automatic gascosole cutting up to 25mm quality cutting suction Donaldson MD2-PLC + DFPRO 4 SPRK with an additional EX protection. Refurbished in 2016 All maintenance or repairs were carried out exclusively by the manufacturers (MicroStep and Donaldson). The prescribed maintenance intervals have always been adhered to. All maintenance and repairs are extensively documented. commissioning on request

Microstep - EuroCut-P 3001.15 Work area: 1500 x 3000 mm Plasma source of Kjellberg HiFocus 160i with automatic Gaskosole Cut quality cutting up to 25 mm Extraction Donaldson MD2-PLC + DFPRO 4 which with additional EX-protection. Refurbished in 2016 All servicing or repairs were solely by the manufacturer (Company MicroStep and Donaldson). The prescribed maintenance intervals were always met. All maintenance and repairs are extensively documented. Commissioning on request

Laser cutting machine Bystar 3015 Bylaser 4000, 4 kW Laser source incl. shuttle table system, cooling system, compl. Cabinet combination with CNC and laser- Control, protection in the cutting area, 2 Cutting heads, reflection absorber, cross-Jet, extraction system Documentation Laser a 19, 000 h Maintained by Bystronic.

CO co² Bystar 3015 4.4 kW, 1500 x 3000 mm, table size incl. removable table, without loader, without extraction, BJ. 2006,. Glass revision in November 2015 Laser: 28.000 h Power: 50,000 hours

Knife Cortina 2600. Year built:1994 Control KS 20A Plasma: Hypertherm Max 100 (cutting up to 30mm) The suction table: 1500mm x 3000mm. With only one burner car instead of 2 or 3, you have a working width of up to 2000mm. The box program on the PC is the OmniWin CAD. Extraction system: Donaldson 5.5 KW to be visited under electricity commissioning on request

Esab Combirex DX 3000 Working range: 2500mm x 4000mm 1x Plasma Support CNC Portal Plasma Cutting Machine Manufacturer: ESAB Type: Combirex DX 3000 Built: 2015 Control: Vision T5 Track width: 3,000 mm frame: 6000mm Working range: 2500mm x 4000 m suction table 1 plasma torch with power source m3 202 torch PT 36 Cutting rods: Punching: 38 mm Cutting: 45 mm laser pointer filter system ex protected cutting software: Columbus Very low operating hours commissioning on request

Bystar 4025 NT 65 Sheet size: 6500 x 2500 mm Interchangeable table system Axis of rotation: 15-315mm 4.4 of kw CO ² laser steel 25 mm Power-on hours 18000 Vacuum pump 16000 With filter system Machine is already dismantled