cold circular saw used for sale

Offer 24455 Specifications: - Saw feed via hand lever - Saw blade diameter 315 mm - Largest opening width vice approx. 160 mm - Cutting range approx. at 90° around 100 mm - Flat up to 135 x 80 mm - Cutting range Li + RE at 45° around 108 mm - Flat up to 100 x 80 mm - Cutting range Li at 60° around 80 mm - Flat up to 70 x 80 mm - Cutting speeds approx. 33 + 66 rpm - Drive 400 V / 1.3 / 1.8 kW - Coolant device - Space requirement approx. W 950 x H 1600 x D 950 mm - Weight approx. 270 kg

Key data: 45 °, 3500 mm, 1350 mm

Basic Cutting length 3500 mm Cast iron sawing unit type Z5 Max. saw blade (not incl.) 500 mm, max. 350 mm with scoring saw blade Scoring unit 120 x 20 mm Cutting height 90°: 175 mm, 45°: 120 mm 3 speeds: 3000/4000/5000 t/min 8D9Kjux2Mt Cutting width between saw blade and Z4 rip fence 1350 mm Z5 Cross Table (1505x760 mm) with Telescopic with Z5 Mitre Stop with 2 Folding Stops Comfort Pack on Cross Table with Extendable Workpiece Roll Frame table with extendable support and degree grid index system with length compensation Motorized height adjustment and inclined position of the saw blade incl. special accessories: Motor 9.2 kW Start/stop in the sliding table

Key data: 45 °, 2800 mm, 1000 mm

Weight approx. 1140 kg Connected load 380V 7.5kW Scoring unit 0.75 kW manually adjustable by pneumatic connection high and lowerable Trimming length 2800 mm Speeds: 600/5000/4000/3000 rpm via V-belts Electric swivel with digital display Electric height adjustment with digital display Cutting width 1000 mm 23S9Fmzq rear support table 950 x 400 mm wide Angle stop 2500 mm with extension 2840 mm with 2 stops Suction port 120mm + 80 mm for PSV Parallelogram protection device with narrow and wide hood Edging stop

Key data: 45 °, 2150 mm, 1100 mm

Connected load 380V 6.1A 3.8kW Saw blade diameter max. 315 mm Weight approx. 330 kg Length of trimming carriage 2150 mm Speed 4000 rpm Suction nozzle 100 mm Cutting width 1100 mm Angle stop Rip fence

saw blade diameter:400 mm total power requirement:380V, 10A dimensions of the machine ca.:1 x 1 x 2 m

CUTTING RANGE . MIN 10MM TO 75MM CUTTING LENGTH . 5-900 SINGLE STROKE -9999 REVERSE CUTTING SPEED. 0 - 40 MM SEC. INFINITELY ADJUSTABLE BACKWARDS 135MM/S MATERIAL FEED SPEED . MAX. 350 MM/S Pwrxaerqe RESILIENCE. MAIN CLAMP 10500N

Equipped with pneumatic feed for clamp, saw diameter 300 mm, without pallet

Power: 3000W; Constant RPM: 900-1500rpm; Blade diameter: 255mm; Cutting angle 0-045; n.w. 23 kg

With 2 roller conveyors

Without pallet and pallet edges.

including spare saw blades

Default

Equipped with: adjustment knob, protected saw blade

Key data: 45 °, 3200 mm, 1500 mm

Connected load 380V Main motor 7.5kW Scoring motor 0.75kW Length of trimming carriage 3200 mm Cutting width 1500 mm Table extension 840 x 320 mm Parallelogram protection device with wide and narrow hood Scoring unit manual adjustment Electric height adjustment Electric swivel with Siko indicator Extraction connection 1x100mm 1x120mm

Key data: 45 °, 3200 mm, 1200 mm

Connected load 380V 15.8A Saw motor 5.5kW Scoring motor 1.2kW Electric height adjustment Electric swivel with LED display Length of trimming carriage 3000 mm Cutting width 1200 mm PSV with narrow hood Table extension 1000 x 470 mm Scoring pneumatically height-adjustable

Key data: 45 °, 1600 mm, 1000 mm

Connected load 380V 10A Motor power 4kW Edging table length 1600 mm Saw Blade-D. 315 mm Cutting height 90 mm Extraction 1x120mm 1x60mm (on extraction hood) Cutting width 1000 mm Table extension 400x400mm Rip fence with fine adjustment Edging frame with angle mitre stop Manual lifting and swivelling of the saw blade Saw blade tilt indicator 1x switch for direct starting of the main engine Saw blade protection cover

Tripod mounted

Circular Saw Blade Sharpening Machine Vollmer Type CNS Suitable for CV circular saw blades for straight and bevel grinding Grinding wheel diameter maximum 150 mm Saw blade diameter 90 – 600 mm Sharpening speed 3 speeds 30/60/80 teeth per minute Drive warping disc motor power 0.2 kW Drive Feed 0.4 kW Dimensions 800 mm x 900 mm x H 1800 mm Weight approx. 250 kg

Circular saw motor, electric motor with brake PERSKE Type: KS 80.12-2 BR ( KS80.2 12-2BR ) 4.4 kW 2830 rpm 400 V IP 54 Shaft diameter: Ø 30 / 60 mm Disc diameter: Ø 160 mm Flange diameter: Ø 215 mm Matching saw blade WZ252 ! used, tested ! Dimensions: 465 x 330 x 260 mm

Key data: 45 °, 2600 mm, 500 mm

400 V, 50 Hz, 2.2 Kw, Cutting height 100 mm, Cutting width 500 mm (extension table + 900 mm added, but the customer shortened the round bar from the rip fence), Sliding table 2600 mm, max. saw blade 315mm, Work table 1060x330 mm, Table extension 390x330 mm, Table extension 900x810 mm, Boom table 1050x630 mm, Cut-to-length stop up to 2800 mm, Height and angle adjustment manually, Extraction connection 100 mm, Hold Operating tools, Spare straps

Key data: 45 °, 2800 mm

Sliding Table Saw Main motor 5.5 KW Scoring saw

WIELOPILA WURSTER DIETZ FR10 WYSOKOSC CIECIA 160MM SZER 850MM SILNIK 90KW PODAJNIK ODBIORNIK ZE ZRZUTEM LASERY

Key data: 350 mm, 100 mm

Automatic with power gearbox also for high-alloy materials.

Sliding table saw Altendorf Type F90 Machine No. 66-9-135 Sliding carriage length 2200 mm Cutting width 800 mm Motor power 5.5 kW Flat belt drive, 2 speeds Cutting width to the right of the saw blade 800 mm max. saw blade diameter without splitting wedge 500 mm Cutting height maximum 165 mm Maximum saw blade diameter with splitting wedge 400 mm Information on the cutting height for saw blade diameter Saw blade diameter 250 mm Cutting height 0 - 55 mm Saw blade diameter 300 mm Cutting height 0 - 80 mm Saw blade diameter 350 mm Cutting height 25 - 105 mm Saw blade diameter 400 mm Cutting height 50 - 130 mm Saw blade bore 30 mm Saw blade cannot be swivelled Extraction connection diameter 120 mm + 80 mm Packaging dimensions approx. 2200 mm x 1400 mm x H 1500 mm Weight approx. 855 kg

Saw blade Ø: 360 mm Cutting range at 90° round: 110 mm Cutting area at 90° rectangle: 110 x 400 mm Cutting range mitred at 45° round: 110 mm Cutting area mitred at 45° rectangle: 110 x 280 mm Cutting speed: 16 - 50 m/min Drive motor: 380 V, approx. 1.5/2 kW Space requirement: 2600 x 1150 x 1600 mm Weight: approx. 1000 kg

Offer 24573 Specifications: - Cutting wheel diameter up to 356 mm - Separation capacity up to 120 mm -Mot. Cutting Feed -One. Transverse infeed 120 mm - Table dimensions 410 x 310 mm - Table travel 220 mm - Drive 400 V / 5.5 kW - Coolant device - Space requirement approx. W 1500 x H 1800 x D 1050 mm - Weight approx. 850 kg

Inv. Num. : 8283 Type: KKS 450 H Producer: Kaltenbach Created: 2019 Parameters: Cutting range: 150 mm Wheel diameter: 450 mm Length: 1320 mm Width: 1020 mm Height: 2000 mm Weight: 1050 kg

OZGENC MAKINA SL 500 automatic circular sawing machine was built in 2021 in Turkey by M.S.K. MOTOR KOMP. MAKINA SAN. TIC. LTD. ŞTI. The machine was specially designed for precision cutting of aluminium profiles at an angle of 90°. The entire machining process, from feeding the material to receiving the finished part, is performed fully automatically. The workspace includes, among others, a two-sided clamping system and a high-quality diamond saw with a diameter of 500 mm, the feed of which is regulated by reliable servomotors. The saw is continuously sprayed with coolant in order to increase the cutting quality and extend the operating time. The offered OZGENC MAKINA aluminium sawing machine is also very easy to operate. The touchscreen operator panel with PLC control provides the user with the necessary information, as well as the ability to quickly configure work programmes. The tota ...

Key data: 45 °, 3200 mm, 1450 mm

Saw blade tilt and height adjustment motorized and with digital display Max. cutting height 200mm Scoring device with separate drive motor Main saw blade with belt drive and speeds 2800/3665/4800 min ̄¹ High dead weight ensures vibration-free running Large boom table with material roller Rip fence with round bar guide and digital position display Extendable aluminium longitudinal stop with two folding stops 7.5 kW main motor mounted on robust cast iron frame Four-bearing sliding carriage with double trolley made of anodised aluminium with high torsional rigidity Multiple locking on the sliding table Standard with table extension and table extension made of sheet steel Large pendulum protection hood can be easily swivelled up with the help of a gas pressure spring Saw blade clamping via tool-free Rapid system Cutting width with rip fence 1450 mm Max. cut-to-length width ...

F 45 EvoDrive: The new F 45 is a masterpiece in terms of technology and design. The one from the ground up on newly designed machine stands exceeds all previous values in the points torsional stiffness and low vibration. The smooth front and the legroom on the ground let you get closer to the sliding table saw and stand on the workpiece. The design-adapted, legendary smooth-running double trolleys is still the measure of all Things when it comes to precision cuts and zero maintenance. In addition comes the control at eye level, with which you can adjust the height and swivel of the saw blade plus, depending on the choice of the control package, the speed and more functions. The new, clear industrial design marks the exceptional position of the Altendorf brand: With this sliding table saw characterful design meets timeless aesthetics. 7" touchscreen with separate keyboard Au ...

HWS 702S Rocking circular saw Saw blade diameter 700mm Cutting capacity round timber max. 240mm Logs max. 370 x 240mm Speed 1400 rpm Motor 7.5kW 400V 50Hz LxWxH 1270 x 730 x 1130mm Weight 128kg G&STÜ-5963710

One-hand adjustable depth of cut control Powerful 800W pneumatic motor "Made in Germany" Stainless steel saw blade cover and depth control Balanced load protects the operator's wrist Robust and low-wear gearbox Adjustable handle for better ergonomics Physical characteristics Weight 3,1 kg Diameter 160 mm Cutting depth 15-51 mm Cutting range 15-51 mm Speed 1225 /min Input Pneumatic Consumption 950 l/min Air pressure 6 bar Inlet air pressure 90 psi Output Pneumatic Power 800 watts 0,9 HP

Integrated electronic motor brake (stops in less than 3 seconds) -One-hand adjustable cutting depth control -R round handle (D-type) -SK spiral cable Physical characteristics Weight 6,3 kg Length 520 mm Width 96 mm Height 194 mm Diameter 180 mm Cutting depth 15-65 mm Cutting range 15-65 mm Drill hole 30 mm Speed 810 m/min Speed 1432 /min Electronic input Phases 1 Voltage 230 V Protection 24 IP Electronic output Power 1050 Watt (50-60Hz)/VA power_power_hp_5060hz 1.4 HP (50Hz)/VA

METALLKRAFT MKS 350 H semi-automatic metal circular sawing machine was built in 2014. The machine, designed to cut workpieces at an angle of 45° and 90°, is equipped with top-of-the-range components that guarantee high operating reliability and cutting precision. These include a 350 mm diameter cutting disc, which ensures that the machined workpieces stand out for their smooth surface without any burrs or distortions. The machine also features, among others, a vice for longitudinal and slot cutting, a reduction gear with diaphragm pump and a mobile safety device for optimum safety during cutting. The METALLKRAFT MKS350H metal circular sawing machine weighs 280 kg. Technical specifications of the METALLKRAFT MKS 350 H circular sawing machine - cutting angle: 45° left/ +90° right - cutting capacity at 90° round cross-section (solid material): 60 mm round cross-section (pipe): 1 ...

Lg.Nr. 24029 Specifications: - Saw blade diameter up to 400 mm - Cutting range at 90° around 130 mm - Square 120 mm - Rectangle 300 x 40 mm - or 240 x 85 mm - at 45° around 130 mm - Square 110 mm - Rectangle 245 x 40 mm - Mitre adjustable Li + Re each 0 - 90 ° - 2 cutting speeds 13 + 26 m/min - Drive 400 V / 1.2 / 1.8 kW - Feed speed of the saw blade hydr. Infinitely variable - Coolant device - Material replenishment machine - Space requirement approx. W 2400 x H 1850 x D 1100 mm - Weight approx. 1250 kg

Saw blade diameter: 350mm, speed: 3400rpm, cutting capacity at 90°: 120mm/75mm, cutting capacity at 45°: 90mm/65mm, machine dimensions X/Y/Z: approx. 700mm/900mm/1000mm, weight: approx. 150kg. Documentation available. On-site inspection is possible.

Saw blade diameter: 350mm, cutting range at 90°: round: 110mm, square: 85mm/85mm, flat: 180mm/85mm, cutting range at 45°: round left/right: 105mm/110mm, square left/right: 85mm x 85mm/85mm x 85mm, flat left/right: 130mm x 85mm/130mm x 85mm. Saw blade bore: 40mm, speed: 74rpm, working height: 925mm. Dimensions X/Y/Z: 1150mm/1500mm/2100mm, weight: approx. 500kg.

Saw blade diameter: 275mm, power: 1.9kW, speed: 80rpm, cutting range (flat): 140mm/70mm, cutting range (miter): 100mm/70mm, max. pipe cutting capacity: 3 inches, solid material cutting capacity: 80mm/60mm, square material cutting capacity: 50mm/50mm. Machine dimensions X/Y/Z: approx. 800mm/700mm/1500mm, weight: approx. 300kg. On-site inspection is possible.

Panel type: Tubular panels for 3-layer parquet, panel length: 2230mm, panel width: 782mm, panel thickness: 9mm-22mm, panel thickness tolerance: 0.5mm/panel, feed rate: 15m-50m/min, output: 12 cycles/min, working height: 1015mm, max. saw blade diameter: 250mm. Extraction included. Documentation available. On-site inspection is possible.

Saw blade diameter: 750mm, saw blade speed: 2200/min, table dimensions: 1500x1500x900mm, cutting height 90°/45°/30°: 295/200/137mm, motor power: 16kW, length: 1800mm, width: 1500mm, height: 1100mm, weight: 650kg. On-site inspection is possible.

Max. cutting height: 100mm, saw blade diameter: 250-400mm, bore: 30mm, carriage length: 2600mm, motor power: 5.5kW, length: 3100mm, width: 2400mm, height: 1500mm, weight: 770kg. On-site inspection is possible.

cutting width: 150 mm machine weight ab.: 300 kg : 27468 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 110 mm capacity 90 degrees: flat: 200x88 mm capacity 45 degrees: round: 115 mm capacity 45 degrees: square: 110 mm capacity 45 degrees: square: 150x80 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,27 t dimensions: 1,1 x 0,95 x 1,7 m - Hydropneumatic semi-automatic - Miter left/right 45° - head diagonal cuts up to 45° (shifter) - Ball bearing table - pneumatic. Double clamping device - Machine base with fog spray device - Chip extraction socket on the saw blade protective hood The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 530 mm capacity 90 degrees: round: 180 mm capacity 90 degrees: square: 170 mm capacity 90 degrees: flat: 380x70 mm capacity 45 degrees: round: 180 mm capacity 45 degrees: square: 150 mm capacity 45 degrees: square: 290x70 mm total power requirement: 2,2 kW weight of the machine ca.: 350 t dimensions: 1,1 x 0,9 x 1,5 m Underfloor aluminum circular saw, hydropneumatic semi-automatic. · Maintenance unit for pneumatic control · Turntable with ball bearings · Suction nozzle for chip extraction system · 2 pneumatic vertical clamps · Rotation range 180° · Movable rear material stop = enlargeable cutting area · Saw blade feed continuously adjustable · Two-hand safety control Horizontal vices (option) · Mist spray device for cooling emulsion · Engine braking · Machine base · The use of our B & S Coolmatic Plus is mandatory for profile cuts necessary . Saw blade ...

saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 110 mm capacity 90 degrees: flat: 200x88 mm capacity 45 degrees: round: 115 mm capacity 45 degrees: square: 110 mm capacity 45 degrees: square: 150x80 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,59 t dimensions: 1,9 x 1,4 x 1,8 m Hydropneumatic fully automatic · Miter Left/Right · Bevel head cuts up to 45° (shifter) a. b. · Hydro-pneumatic control of the saw head · Pneumatic double clamping device · Pneumatic vertical clamping device · Electro-pneumatic material feed unit with material hold-down device · Vernier for length adjustment · Integrated coolant spray device · Swarf suction nozzle on the saw blade protective hood · Leftover piece length in automatic mode 210 mm MPS control: · Save cut start/end · Display of current consumption, number of pieces, cutting ...

saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 110 mm capacity 90 degrees: flat: 200x88 mm capacity 45 degrees: round: 115 mm capacity 45 degrees: square: 110 mm capacity 45 degrees: square: 150x80 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,22 t dimensions: 0,7 x 0,9 x 1,9 m ATTENTION: SPECIAL PRICE! - Miter left/right 45° - head diagonal cuts up to 45° (shifter) - Pneumatic double quick clamping device Vices close when lowering - Ball bearing table - Machine base - Powerful and powerful - High-quality workmanship The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 350 mm capacity 90 degrees: round: 100 mm capacity 90 degrees: square: 100 mm capacity 90 degrees: flat: 100 x 195 mm capacity 45 degrees: round: 100 mm capacity 45 degrees: square: 100 mm capacity 45 degrees: square: 100 x 135 mm saw blade turning speeds: 2800 U/min total power requirement: 1,5 kW weight of the machine ca.: 250 kg dimensions: 0,7 x 0,7 x 1,4 m ATTENTION: SPECIAL PRICE - Miter left/right 45° - fixed locking points at the most important miter angles - Pneumatic double clamping device - Safety engine brake - Complete with fog spray device and machine base The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 105 mm capacity 90 degrees: flat: 180 x 70 mm capacity 45 degrees: round: 120 mm capacity 45 degrees: square: 100 mm capacity 45 degrees: square: 135 x 60 mm saw blade turning speeds: 1700 / 3400 U/min total power requirement: 1,5/2,2 kW weight of the machine ca.: 0,285 t dimensions: 1,2 x 1,4 x 1,4 m Semi-automatic circular saw for sawing solid and aluminum Hollow iron materials and light metal alloys with electro-welded Carbide toothed washer. Machine for miter cuts from 45° right to 45° left. Through the Alignment along the vertical is possible Sawing operations with the head inclined between 0° and 45° to the left. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.