coat used for sale

Powder curing furnace 2,000 x 1,900 x 2,000 mm 1 Inner dimension length 2,000 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m³/h 10 electric motors 1 pc 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 33 kW 12 hinged doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set of stainless steel INOX with heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc oven is electrically operated 15 Exhaust air 1 pc device for exhaust air pipe, manual flap guide

Powder curing furnace 2,000 x 1,900 x 2,000 mm 1 Inner dimension length 2,000 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m³/h 10 electric motors 1 pc 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal output 33 kW = 28,380 kcal/hour 12 hinged doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set of stainless steel INOX with heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is operated with gas burner 15 Exhaust air 1 pc device for exhaust air pipe, manual flap ...

Powder curing furnace 3,500 x 1,900 x 2,000 mm electric 1 Inner dimension length 3,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m³/h 10 electric motors 1 pc 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 58 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device for exhaust air pipe, manual flap ...

Powder curing furnace 3,500 x 1,900 x 2,000 mm gas operation 1 Inner dimension length 3,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m³/h 10 electric motors 1 pc 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal output 58 kW = 49,880 kcal/hour 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set of stainless steel INOX with heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc. stove is heated by gas burner. 15 Exhaust air 1 pc device for exhaust air pipe, m ...

Powder curing furnace 4,500 x 1,900 x 2,000 mm electric 1 Inner dimension length 4,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 5,700 = 11,400 m³/h 10 electric motors 2 pcs 2x 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 74 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device for exhaust air ...

2.1.1. Walk-in cleaning booth, pre-treatment for steel and aluminium The cleaning booth is designed for automatic cleaning. Spraying can be done at medium pressure. There are 7 different spray tanks in the cabin. The part sizes are max. L= 6,000mm, W= 2,000mm, H= 2,300mm. 1 Dimensions of the cab length 6,500 mm Width 3,000 mm Height 3,600 mm 2 dimensions of the pre-treatment complete Length 6,600 mm Width 4,640 mm Debpm0Nom Height 4,300 mm 2.1.1.1. 1. Degreasing/Neutral Pickling Process Heated bowl, 50-55°C, time = 3-6 minutes, draining time = 80 seconds 2.1.1.2. 2. Process Acid Mineral Pickling Heated bowl, 50-55°C, time = 3-6 minutes, draining time = 80 seconds 2.1.1.3. 3. Rinsing Process 1 in this chamber rinsing is done at ambient temperature, time = 0.75-1.5 minutes, draining time = 1 minute 2.1.1.4. 4. Rinsing Process 2 in this chamber is rinsed at ambient tem ...

Powder coating plant oven, cabin, etc. Powder Coating Booth Open Spray Stand Dimensions of powder level Width 2,000 mm Depth 2,100 mm Height 2,200 mm Fan 1 pc. 6000 m³/h Power 3 kW (electric motor) Filter 4 type filter cartridges (à ⌀325 x 600 [mm]) Electromagnetic valves 2 Pcs. 1" "Turbo" Italy Absolute filter 1 pc. type bag filter Powder Pistol Wagner "Prima Sprint" Mains Standard 230 VAC Frequency 50 – 60 Hz Input compressed air 6-8 bar Output compressed air 0.05 – 5.5 Nm³/hr. Powder curing furnace Inner dimension length 3,225 mm Inner dimension width 1,400 mm Inner dimensions height 2,000 mm Insulation rock wool 150mm [75 Kg/m³] Temperature max. 220°C Fans 1 pc. 4,500 m³/h Electric Motors 1 pc 1.5 kW, 1450 rpm, 3 F, 50 Hz Thermal power 39 kW Doors on both sides 2 pcs. Manual, insulated with rock wool 150mm 70Kg/m³ Heati ...

.1.1. Powder Coating Booth, Open Spray Stand The overspray during powdering is absorbed by the extraction unit. The powder spray stand is delivered on rollers and is therefore mobile. - The extraction system is equipped with a 60 L powder container (rollable). - As a 1st stage, there are 4 filters in the extractor. - Above the cab is the absolute filter. 1 Dimensions of the powder stand width 2,450 mm Depth 2,350 mm Height 2,700 mm 2 fans 1 pc. 6,000 m³/h Electric motor 3.0 kW 3 Filters Φ 325x800 4 pcs Type Filter Cartridges 4 Electromagnetic Valves 2 pcs 1" "Turbo" Italy 5 absolute filters 1 pc. type pocket filter 2.1.2. Powder curing furnace Mzlxwbat 1 Inner dimension length 4,000 mm 2 Inner dimensions width 1,500 mm 3 Inner dimensions height 2,200 mm 4 Outer dimensions incl. thermoblock length 5,250 mm 5 Outer dimensions incl. thermoblock width 2,050 mm ...

Powder coating system for large parts Example:(all sizes can be changed individually) Space requirement: 30 x 15 meters Part size: L= 6,200mm W= 2,300mm H= 2,000mm Cleaning booth walk-in incl. spray wreath automatic 1 Dimensions of the cabin Length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Mass of tanks Length 1,200 mm Width 850 mm Height 1,000 mm 2 Dimensions of the cabin complete Length 9,140 mm including tanks width 5,580 mm Height 4,200 mm Coating booth walk-in, manual coating Lmmuapd8S 1 Dimensions cabin length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the cabin including extraction Length 10,125 mm Width 4,500 mm Height 3,400 mm Powder curing furnace 1 Inner dimension length 6,500 mm 2 Inner dimensions width 2,500 mm 3 Internal dimensions height 2,950 mm 4 Outer dimensions incl. thermoblock length 7,600 mm 5 Outer dimensions inc ...

1.Powder curing furnace 2,000 x 1,900 x 2,000mm 1 Inner dimension length 2,000 mm 2 Inner dimensions width 1,900 mm 3 Inner dimension height 2,000 mm 4 Outer dimensions incl. thermoblock length 2,300 mm 5 Outer dimensions incl. thermoblock width 2,300 mm 6 Outer dimensions incl. thermoblock height 2,700 mm 7 Substructure 1 set of steel profile 50 x 50 mm 8 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5005 9 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 10 floor stove gets 2 entry rails for tray wagons 11 Temperature 220°C 12 fans 1 pc. 6,000 m³/h 13 electric motors 1 pc 1.1 kW , 1450 rpm, 3 F, 50 Hz 14 Thermal output 36 kW = 30,960 kcal/hour 15 wing doors on one side 2 pcs insulated with rock wool 150mm 70Kg/m² Heating Indirectly via thermoblock Thermoblock 1 set stainless steel INOX AISI 316 heat-resistant fans and heat-resistant bea ...

1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 2. Powder Coating Booth -KG DUO-01 3. Wagner powder coating plant, – Prima Sprint – 1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 1 Inner dimension length 1,500 mm 2 Inner dimensions width 1,200 mm 3 Internal dimensions height 1,750 mm 4 Outer dimensions incl. thermoblock length 2,250 mm 5 Outer dimensions incl. thermoblock width 1,815 mm 6 External dimensions incl. thermoblock height 2,006 mm, 2,296 mm incl. exhaust pipe 7 Substructure 1 set of steel profile 8 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 9 insulation walls, ceiling 1 set of rock wool 150 mm, floor is insulated with 50 mm 10 Floor Furnace Gets 2 Entry Rails for Tray Wagons 11 Temperature 220°C 12 fans 1 pc. 2,600 m³/h 13 electric motors 1 pc 1.1 kW , 1450 rpm, 3 F, 50 Hz 14 Thermal power 14 kW 15 hinged doors, single ...

Powder furnace el. or gas Powder curing furnace 6,500 x 1,900 x 2,000 mm 1 Inner dimension length 6,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 7,500 = 15,000 m³/h 10 electric motors 2 pcs 2x 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 110 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device fo ...

The continuous system consists of the following components: Chemical pre-treatment by spraying Dryer Powder coating system Powder curing furnace Conveyor technology (cycle method) Electrical control Overall length: 30,000 mm Overall depth: 4,300 mm Width: 6,500 mm Workpiece weight (max.): 100 kg Temperature: 220 °C Heat output: 80,000 W Workpiece width (max.): 800 mm Workpiece height (max.): 1,200 mm Workpiece length (max.): 2,500 mm Insulating material: Mineral wool 75 kg/m³ Insulating thickness: 150 mm

Powder curing furnaces in various sizes, gas or electric 1 Inner dimension length 1500 - 6,500 [mm] 2 Inner dimensions width 1700 - 1,900 [mm] 3 Inner dimensions height 2,000 [mm] 4 Steel profile substructure 5 walls Galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling rock wool 150mm 75Kg/m² 7 Floor furnace gets 2 entry rails for tray trolleys (optionally with conveyor technology) 8 Temperature 220°C 9 fans 1 - 2 pcs. 2600 - 15,000 [m³/h] 10 electric motors 1 - 2 pcs 1.1 - 6 [kW] , 1450 [rpm], 3 F, 50 [Hz] 11 Thermal power 14 - 99 [kW] 12 hinged or sliding doors on one or both sides 2 - 4 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock Stainless Steel INOX AISI 316 Heating Electric or Gas Heat-Resistant Fans and Heat-Resistant Bearings, Thermoblock Has Overheating Protection

Powder coating plant (complete) with 3 zones of chemical pre-treatment and Hybird ovens (dryer and curing oven) Gas and electricity (gas or electricity also possible) The facility consists of: Chemical pre-treatment with reverse osmosis system Dryer with hybrid thermoblock Walk-in coating booth with extraction unit KG PSW 8000 Powder curing furnace with hybrid thermoblock Conveyor system with transverse displacement, manual Electric control unit Specification of production Type of workpieces varies Material of the workpieces Steel (other metals or multimetal possible on request) Maximum weight of the load carrier 200 kg System type: Manual conveyor Dimensions of the maximum workpiece in the curing furnace Max. length 3000 mm Max. width 1500 mm Max. height 1500 mm Dimensions of maximum workpiece in chemical pretreatment Max. length 3000 mm Max. width 800  ...

COMPONENTS OF THE SYSTEM Preheating oven Powder coating booth Fluidized Bed Powder Coating Lifting system Automatic Transport System – Conveyor Belt C-80 Electrical control and installation Transport and assembly Fluidized Bed Powder Coating Booth The powder is fluidized in the fluidized bed vessel when the part is preheated and positioned over the fluidized bed container. The lifting system lifts the fluidized bed tank and the part is coated. After the coating process is completed, the fluidized bed is lowered again and an air blowing system blows off the excess powder on the part. The process can be carried out fully automatically. The cab's system is designed for powder coating with powder recovery and consists of a powder chamber for powder application, a monocyclone and a post-filter for extracting powder residues Chamber dimensions Length: 2000 mm Width 1 ...

Oven, doors single-sided, electric Dimensions: 3,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 54 kW Auxiliary heating: electrically indirect via thermoblock

Dimensions: Length: 7400 mm Width: 4000 mm Height: 3236 mm Extraction capacity: Q = 18000 m³/h P = 15 kW The cabin has a suction machine with filters to suck the powder from the cabin floor. The powder booth is set up in a pit to lower the entire height of the painting line. Manual doors are installed to enter the workpieces into the cabin. The overspray is extracted during powder coating via the floor. On the floor there is a grate for walking on and under the grate there is a second flat floor with automatic self-cleaning system, connected by air ducts with post-filter. A self-cleaning system automatically blows the powder from the bottom to the post-filter (suction machine) and consists of

Oven, doors single-sided, gas Dimensions: 4,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Recirculating air: Q = 12000 m³/h P = 2 x 2.2 kW Heat output: 69 kW Auxiliary heating: Gas indirectly via thermoblock

Chemical pre-treatment 3 zones for powder coating with spray ring (automatic) and manual Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Max. workpiece dimensions (automatic): Length: 6500 mm Width: 1000 mm Height: 2300 mm Max. workpiece dimensions (manual): Length: 6500 mm Width: 2500 mm Height: 2300 mm Tanks are positioned at ground level with a sloping floor. Tank No.1 is thermally insulated and is heated by electric heaters. Achievement: 27 kW. Volume of each tank = 1.00 m³. For degreasing (1st tank), a medium pressure pump is used to operate the 1st spray system. The rinsing phases are also operated by a pump with medium pressure via the 2nd spray system. On the bottom i ...

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

Chemical pre-treatment for powder coating (3 zones) 1 Dimensions of the cabin length 3900 mm Width 1600 mm Height 2500 mm 2 dimensions of the pre-treatment complete length 4000 mm Width 3000 mm Height 4000 mm 3 Passage opening width 1000 mm Height 1700 mm The chemical pretreatment for the use of nanotechnology or phosphating consists of 3 stages in 1 spray chamber. Chemical spray pretreatment works in time and this means that the workpieces are manually pushed into the chamber. After closing the doors, the passage starts and the pumps start spraying. Each pump has different spray times. After the spraying process is finished, there is an alarm indicating that the door can be opened and the workpiece can be pulled out. All pre-treatment functions a ...

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

The curing furnace consists of a tunnel furnace in which the workpieces are baked after coating. The furnace is a straight tunnel furnace. The frame is made of steel with insulated panels. The mineral wool insulation becomes 150 mm thick in a special construction to prevent thermal bridges 1 Inner dimension length 7,000 mm Inner dimensions width 1,000 mm Inner dimensions height 2,500 mm 2 Outer dimensions incl. thermoblock, length 7,200 mm Outer dimensions incl. thermoblock, width 1,300/2,300 mm External dimensions incl. thermoblock, height 2,800 mm 3 substructure 1 set of steel profiles 80 x 80 and 40 x 80 mm 4 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5010 5 Insulation 1 set of rock wool 150mm 75 Kg/m³ 6 Ventilation system 1 set of galvanized steel sheet 7 Temperature max. 220°C 8 fans 1 pc. 7,500 m³/h 9 electric motors 1 pc  ...

Open Powder Spray Stand Dimensions: 2500 x 2250 x 2700 [mm] Extraction capacity: Q = 8000 m³/h P = 5.5 kW Filter: 1 stage: Filter cartridges 4 pieces à Ø 325 x 1000 [mm] 2nd stage: Pocket filter (absolute filter for fine dust) Note: The overspray during powdering is absorbed by the suction unit. The powder spray stand is delivered on rollers and is therefore mobile

Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Extraction capacity: Q = 18000 m³ P = 15 kW The cab has 2 doors on one side for the insertion/outlet of the workpieces. The components are pushed into the cabin for coating via the overhead transport system. Walls, ceiling and doors are made of panels. The filters positioned on the roof absorb dust and other particles from the outside, thus ensuring clean ambient air in the cabin. The overspray during powdering in the cabin is absorbed by the extraction unit

SPECIFICATIONS: Machining width: max. 1300 mm Processing thickness: max. 80 mm Installed power: 9 kW 01 Low Pressure Pump 04 Painting units COMPOSITION: AGGREGATE I Dosing Unit Steel roller Speed adjustable via the CN control Power: 0.75 KW Speed: 1400 rpm AGGREGATE II Applicator Roller: Ø 250 mm rubber Power: 0.75 kW Speed: 1400 rpm AGGREGAT III Filler Steel roller Power: 0.75 KW Speed: 1400 rpm AGGREGAT IV Dosing Unit Steel roller Power: 0.75 kW Speed: 1400 rpm Control: SORBINI

UV-Beschichtungsmaschine - UV-Coating machine Billhöfer CPUV-112 Year 1982 - Serial-No. 9035 Format min. 300 x 500mm Format max. 820 x 1120mm Feeder automatic Mabeg Grammatur 60 up to 500 gr/m2 card board UV-Beschichtungsmaschine - UV-Coating machine Billhöfer CPUV- Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Manufacturer: Bürkle, Type: Doppelwalze DAL 2, Year: 1992, Work piece width min-max mm: 10 - 1300, Min.-max. workpiece length in mm: 100, Min.-max. workpiece height in mm: 3 - 120, Operating side: rechts, UV-laquer roller: yes, regelbarer Direktantrieb für Auftragswalze: yes , Auftragswalzengeschwindigkeit m/min.: 5 - 30, Direktantrieb Dosierwalze: yes, Verchromte Dosierwalze mm: yes, Attachment bracket roller: yes, everse drive: yes, rbakel: 1 x, Feeding speed min/max: 5 - 30, Hight adjustment by engine: yes, Pump system: Membrane, Year :1992

2016 ONLINK Technologies SIGMET-2000V High vacuum coating machine The system coats even the most complex 3D molded parts made of metal, glass or plastic with aluminum and achieves exact, precise quality and flexibility. Total machine operating hours: 700 hours. Characteristics: - Double door arrangement for high productivity - Precise drive system - Planetary drive for even coating - Vertical arrangement of the substrate holders - Modular and very flexible structure - Annealing pretreatment by alternating or direct current - Annealing pre-treatment by MF (40 kHz) - Recipe management and process visualization - Base coat - PECVD process - Top Coat (protective layer) - PECVD process - Highly effective and fast vacuum system - Remote maintenance Typical applications: - Automobile – inside and out - Cosmetics - Household and furniture - Glass and bottles - Decorative  ...

For sale is a Wagner WAC 70 circular saw in excellent condition, including a bundle loader. This high-quality machine is ideal for precise cutting and efficient handling of wood and workpieces in wood processing. Type: Circular saw Model: Wagner WAC 70 Additional equipment: Bundle loader Features of the Wagner WAC 70: Precision: The WAC 70 offers precise cuts for a wide range of wood types and formats. Performance: Robust construction for a long service life and high performance. Efficiency: The integrated bundle loader enables fast and efficient material feed, which significantly speeds up the production process. Operating Voltage: - Main: 400V, 50Hz - Control Voltage without transformer: 230V - Control Voltage with transformer: 25V Rated Current: 23A

Manufacturer: Bürkle, Type: Betonpflasterlackieranlage, Year: 2007, Finished product: Oberflächenbeschichtung, Work piece width min-max mm: 1300, Destacking plant: Vakuum, Inlet conveyor: mit Ausrichstation, 1 UV dryer lamps/Watt: yes, Conveyor belt/roller: Band, 2 paint roller: Bürkle SLC 1300, 2 UV dryer lamps/Watt: yes, wast cleaning: yes, Conveyour system: Band, Stacking plant: yes, Year :2007

Manufacturer: Purete , Type: Einzellackwalze, Year: 2017, Control: Shllin, Work piece width min-max mm: 10-1300, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 3-80, Operating side: rechts, Working height: 890, Lackauftragseinheiten: 1, Vorschub Transport m/min min - max: 5-20, kW - Leistung Transport: 0,5, Shore: ca.40, Durchmesser Auftragswalze mm: ca.240, Dosierwalze verchromt: yes, Pump system: Membrane, Carriage: yes, Electronic control board: yes, Strassenbetrieb: yes, Carriage: yes, Year :2017

Manufacturer: Purete, Type: PRT-R2113AM Doppellackwalze, Year: 2017, Control: Shillin, Work piece width min-max mm: 10-1300, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 6-80, Durchlassbreite min-max mm: 1300, Operating side: rechts, Lackauftragseinheiten: 2, Vorschub Transport m/min min - max: 5-20, kW - Leistung Transport: 0,5, Conveyor: Band, Einbaulänge UV mm: 2000, Compressed air bar: 6, Year :2017

Manufacturer: Bürkle, Type: DALD 1300, Year: 1990, Work piece width min-max mm: 10-1300, Min.-max. workpiece length in mm: 250, Operating side: links, Working height: ca.900, Widht of roller coater: 1350, Widht of metering roller: 1350, Attachment bracket roller: yes, rbakel: no, Work piece thickness max mm: 5, Feeding speed min/max: 5-25, Hight adjustment by engine: no, Year :1990

Manufacturer: Giardina, Type: G02/05, Year: 2008, Control: Giardina, Work piece width min-max mm: 1300, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 3-120, Working height: 900, Lackauftragseinheiten: 1, Vorschub Transport m/min min - max: 7-20, kW - Leistung Transport: 1,0, Durchmesser Auftragswalze mm: ca.240, Reverse und Gegenlauf: yes, everse drive: yes, rbakel: yes, Roller lift out: yes, Hight adjustment by engine: yes, Type of transportation: Band, Pump system: Membrane, Carriage: yes, Strassenbetrieb: möglich, Carriage: yes, Year :2008

Manufacturer: Bürkle Lackauftragsmaschine , Type: DAL 1, Year: 1989, Control: hand, Work piece width min-max mm: 10-1300, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 6-120, Operating side: rechts, Working height: 890 +-, Lackauftragseinheiten: 1, Vorschub Transport m/min min - max: 6-30, kW - Leistung Transport: 0,75, Auftragswalzengeschwindigkeit m/min min-max: 6-30, Durchmesser Auftragswalze mm: 238, Dosierwalze verchromt: yes, Attachment bracket roller: yes, rbakel: yes, Year :1989

Manufacturer: Hymmen, Type: SGC, Year: 1999, Control: Hymmen, Work piece width min-max mm: 1300, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 3-120, Operating side: rechts, Vorschub Transport m/min min - max: 5-25, kW - Leistung Transport: 0,75, Glättewalze mm: yes, Glättewalzengeschwindigkeit: 5-25, Year :1999

Manufacturer: Delle Vedove Vakumat Kanten-hydrophobierung (Wachsauftrag) Clicksystem, Type: BL 030-00, Year: 2002, Control: Delle Devove Siemens, Auftragsmaterial: Wachs, Vakuumauftragseinheit Menge: 2, Schnellwechselsytem: yes, Vakuumturbine: 1, Halter für Auftragseinheiten: 2, Heizung für Material: yes, Year :2002

Manufacturer: Hymmen, Type: TLX 2,0, Year: 1982, Control: hand, Work piece width min-max mm: 1300, Min.-max. workpiece height in mm: 10-60, Working widht max mm: 1300, Working height: 950, regelbarer Direktantrieb für Auftragswalze: yes, Auftragswalzengeschwindigkeit m/min.: 10-25, Gummierte Auftragswalze mm: yes, Gummiqualität : 50, Direktantrieb Dosierwalze: yes, Verchromte Dosierwalze mm: yes, Metering roller drive m/min: ca.4-12, rbakel: yes, Compressed air bar: 6, FREE TEXT: ohne Schaltschrank, Year :1982

Manufacturer: Sorbini / Tagliabue, Type: Walzstrasse, Year: 1998, Work piece width min-max mm: 1.300, Min.-max. workpiece height in mm: 3 - 80 , Min.-max. workpiece length in mm: 300, Feeding speed min-max m/min: 6 - 24, Inlet conveyor: yes, Lackwalze 1: T/20-MF, UV Trockner 1: 1 Lampe, Lackwalze 2: T-20-MF, UV TRockner2: 3 Lampen, Lackwalze 3: T-20MF, UV Trockner 3: 3 Lampen, Paint sander: TAG 13KS DPSTRA, Paint rollers: 3, Year :1998

Manufacturer: Cefla, Type: Hotmelt SP1-EVO, Year: 2015, 2 roller machine: yes, Min.-max. workpiece height in mm: 0-80, Working widht mm: 1300, Roller cooling system: Heizung, Feeding - kW: 0,75, Feeding speed max m/min: 5-20, Compressed air bar: 2-10, Year :2015

Manufacturer: Hymmen, Type: TLX M, Year: 1992, Work piece width min-max mm: 1300, Working widht max mm: 1300, Operating side: links, Working height: ca 980, UV-laquer roller: yes, Verchromte Dosierwalze mm: yes, Glättwalzengeschwindigkeit ca. m/min.: 80, Steuerung Nicht-Ex : 5 - 25, Widht of roller coater: yes, Application roller drive m/min: yes, Widht of metering roller: Band, Year :1992

Manufacturer: Purete, Type: PRT-R1106, Year: neu, Work piece width min-max mm: 620, Min.-max. workpiece length in mm: 300, Min.-max. workpiece height in mm: 2 - 80, Working widht max mm: 620, Operating side: rechts, UV-laquer roller: yes, Auftragswalzengeschwindigkeit m/min.: 0 - 20, Verchromte Dosierwalze mm: yes, Feeding speed min/max: 0 - 20, Year :neu

Manufacturer: Purete, Type: PRT-R2113b, Year: Neu, Work piece width min-max mm: 1.320 , Min.-max. workpiece length in mm: 300, Min.-max. workpiece height in mm: 2 - 80, Working widht max mm: 1.320, Operating side: rechts, Auftragswalzengeschwindigkeit m/min.: 2 - 80, Gummierte Auftragswalze mm: 1.450, Verchromte Dosierwalze mm: yes, Widht of roller coater: 1.450, Required space L x W x H mm: 1.600 x 2.575 x 1.700 mm, Year :Neu

Manufacturer: Sorbini, Type: T/20-MF, Year: 1999, Control: Cefla, Work piece width min-max mm: 1350, Durchlassbreite min-max mm: 1350, Working height: links, Vorschub Transport m/min min - max: yes, kW - Leistung Transport: yes, Auftragswalzengeschwindigkeit m/min min-max: 5-25, Gummierte Auftragswalze(n): yes, Auftragseinheit 1 shore härte: yes, Auftragseinheit 1 : yes, Gummierung mm: 5-12, Shore härten möglich: yes, Shore: möglich, Durchmesser Auftragswalze mm: yes, Type of transportation: 2,5, Working hight approx mm: 1520, Year :1999

Manufacturer: Bürkle, Type: SAL, Year: 11.97, Work piece width min-max mm: 100-1300, Min.-max. workpiece length in mm: 350, Min.-max. workpiece height in mm: 3 - 80, Operating side: rechs, Working height: 920 +-, UV-laquer roller: yes, regelbarer Direktantrieb für Auftragswalze: yes, Auftragswalzengeschwindigkeit m/min.: 6 - 30, Direktantrieb Dosierwalze: yes, Attachment bracket roller: yes, everse drive: yes, rbakel: yes, Type of transportation: Band/Rolle, Pump system: Membrane, Year :11.97

Manufacturer: Bürkle, Type: SLC 1300, Year: 1999, Control: Sütron, Work piece width min-max mm: 1300, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 3-120, Working widht max mm: 1300, Operating side: rechts, Working height: 930, regelbarer Direktantrieb für Auftragswalze: yes, Auftragswalzengeschwindigkeit m/min.: 6-30, Gummierte Auftragswalze mm: 238, Metering roller drive m/min: 1-6, Attachment bracket roller: yes, rbakel: yes, Roller lift out: yes, Hight adjustment by engine: yes, Type of transportation: Band, Pump system: Membrane, Year :1999

Manufacturer: Hymmen Glättewalze, Type: SGC, Year: 1995, Control: Hymmen, Work piece width min-max mm: 1.350, Min.-max. workpiece height in mm: 3 - 80, Working height: links, Lackauftragseinheiten: ca. 980, Year :1995

Manufacturer: Hymmen Lackwalze ELX 1.0 Bedienseite links, Type: ELX 1,0, Year: 1995, Work piece width min-max mm: 1350, Min.-max. workpiece height in mm: 3 - 80, Working height: rechts, Lackauftragseinheiten: ca 980, Vorschub Transport m/min min - max: yes, Year :1995