133,933 used machines on RESALE, but how to find them? Machine Search
CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets with ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Warehouse number: 3691 CNC ROTARY TABLE Manufacturer: Hydex, Type: AT-250 - 5 Axis Year of construction: 2022 Specifications: Table size 250 mm Center Height 320 Spindle hole 75H7 mm CNC control 2 ashes revolutions 50 per min Control Fanuc-Mitsubishi-Siemens-Heidenhain
X=3500mm Y=2000mm Z=1250mm W=800mm H=360° spindle 130 mm, ISO 50, max. 1600 rpm table 1600 x 1800 mm with a load of 12000 kg with Siemens electric and CNC Heidenhain TNC 415B Oil cooled: Schimpke. Dismantled. The machine has been used very little = in very good technical condition.
CNC Thread Rolling Machine - Thread Rolling Machine Thommen PR17 CNC 2 wheels Rotation speed of the rollers electronically controlled Position and speed are managed electronically Spindle diameter 54 mm 2 pairs of columns (closed and open) The machine is in our warehouse in Gussago BS, energized Test run possible Mimu Machine Tools
CNC centerless grinding machine Monzesi mod Monza 510 CNC 6 axes complete with piece loading and unloading system CNC Fanuc 160i-T Under power in our warehouse in Gussago BS. Mimu machine tools Italy
ORT 3RP48 CN CNC / PLC thread rolling machine scaffolding sleeves threading, shelves studs threading electronic overhaul/retrofit Under power in our warehouse in Gussago BS. Test run possible Mimu Machine Tools
grinding length: 900 mm grinding width: 510 mm workpiece height: 400 mm table surface area: 800 x 400 mm longitudinal feed of the table: max. 980 mm table speed -stepless-: 1 - 35 m/min grinding wheel size: 355 x 51 x 127 mm cross feed of the table: 460 mm cross feed: 1 - 40 mm/Hub vertical feed autom.: 0,005 - 0,04 mm/Hub rapid traverse vertical: 0,5 m/min grinding spindle speed: 1450 U/min grinding spindle drive: 5,6 kW table load capacity: max. 1000 kg total power requirement: 10 kW weight of the machine ca.: 4,4 t Accessories: magnetic plate 800 x 400 mm, various grinding wheels with and without flanges, wet grinding attachment with paper band filter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 550 mm
IMMEDIATELY AVAILABLE - video link on request CNC-controlled 3-axis sawing and drilling center for sophisticated production technology Encapsulated, compact machine - designed as a closed production island - no noise and no chips in the machine environment - large extraction connection for efficient chip extraction. (The machine is also supplied as a two-axis sawing center without drilling unit). Dimensionally accurate 90° saw cuts both in small series and in large series production. CNC control based on Windows® with touch screen and color screen, simple menu-driven programming with symbols, remote maintenance module. Absolutely burr-free precision sawing of all materials such as - aluminum - bronze - GRP (glass fiber reinforced plastics) - wood - copper - brass and various plastics such as PVC and polyamide. Drilling (through holes and blind holes – step drill ...
Key data: 550 mm
IMMEDIATELY AVAILABLE - video link on request KA 550 CNC-DRILL CNC-controlled 3-axis sawing and drilling center for sophisticated production technology Encapsulated, compact machine - designed as a closed production island - no noise and no chips in the machine environment - large extraction connection for efficient chip extraction. (The machine is also supplied as a two-axis sawing center without drilling unit). Dimensionally accurate 90° saw cuts both in small series and in large series production. CNC control based on Windows® with touch screen and color screen, simple menu-driven programming with symbols, remote maintenance module. Absolutely burr-free precision sawing of all materials such as - wood - aluminum - bronze - GRP (glass fiber reinforced plastics) - copper - brass and various plastics such as PVC and polyamide. Drilling (through holes and blind hole ...
table diameter: 200 mm workpiece height: 100 mm number of wheels: 1 Control: Robot CNC total power requirement: 6 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 1,83 x 2,04 x 2,1 m Technical data - Grinding capacity : Ø 0.025 –12.7 [mm] - Bar diameter : Ø 1.0 –12.7 [mm] - Grinding length : W15 (option W20) - Z-axis : 35[mm] Resolution : 0.5 [µm] – X- axis : 25 [ mm] Resolution : 0.1µm – Y-axis : 286[mm] Resolution : 0.5µm – U- axis : 15 [mm] Resolution : 0.1µm Head Motor: 0.70 [kW] Rotation: 300 – 3000 [rpm] Grinding - Raw grinding : 1.5 [kW] Spindle : Ø 60 [mm] Grinding wheel diameter : Ø 200 [mm] Cutting speed : 30 m/sec. - Completion: 0.75 [kW] Spindle: Ø100 [mm] Grinding wheel diameter: Ø150 [mm] Cutting speed: adjustable - Dimensions (L x W x H): 1830 x 2040 x 2100 mm - Weight: approx. 1800 [kg] Accessories - Loading and unloading robots - F ...
Tailstock, counter bearing for dividing head, dividing head -Manufacturer: Swedturn, Type ST12 CNC 300 tailstock -Quill: hydraulically driven -Dimensions: see photos -Dimensions: 900/650/H450 mm -Weight: 265 kg
Key data: 130 , 3500 , 2000
CNC SIEMENS 840D X-axis (longitudinal) 3500 mm Y-axis (transverse) 2000 mm Z-axis (vertical) 1250 mm Table length 1800 mm Table width 1800 mm Maximum workpiece weight 12000 kg Spindle diameter 130 mm Maximum spindle speed 800 rpm Magazzino utensili 52 posti Spindle motor 37 kW Year of revision 2005 ------------------- Length x width x height 7200 × 7800 × 4900mm Weight 32000 kg
Control: TMJ Max.cutting range: 360 x 305 mm Cutting speed:10 ? 100 m/min Saw band dimension: 3660 x 27 x 0,9 mm Automated bar shift: YES Coolant tank:100l Chip conveyor: YES Made in Czech Republic
cutting capacity - round: 300 mm dimensions of saw-band: 3320 x 27 x 0,9 mm cutting capacity - flat: 330 x 260 mm cutting capacity - square: 260 mm Control: evolution work height max.: 870 mm : 40 / 80 mt/min weight of the machine ca.: 1050 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 300 mm : 300 mm : 300 x 260 mm saw band length: 3920 x 34 x 1,1 mm table height: 780 mm band speed: 20 - 100 m/min total power requirement: 3,7 kW weight of the machine ca.: 1,65 t dimensions: 2,0 x 2,05 x 1,7 m PROMOTIONAL PRICE 2-column high-performance automatic band saws from the SBS series The SBS series impresses with its sophisticated technology, high quality and longevity and unrivaled, sophisticated standard equipment. • Modern SNC 20 control for CNC version • Frequency-controlled saw drive • Control buttons with pictograms • Work light • Powered chip brush • Hydraulic belt tension • Clamping pressure regulation • Double vice (before and after the belt) • Creep path for positioning • Bundle tension prepared electrically and hydraulically • Chip conveyor The SNC 20 control allows you to enter up to 20 different sawing tasks (length and number of pieces) co ...
Description HEYLIGENSTEDT face lathe KH35-CNC with control Sinumerik 840 D Details Serial No. 70000134 Turning diameter over bed carriage 900 mm Turning diameter over bed sheets 1,400 mm Center height above floor 1,480 mm Tip height over bed panels 680 mm Bed width 850 mm Bed height 550 mm Control SIN 840 D Main spindle diameter at front bearing 206 mm Main spindle bore 100 mm max. main spindle torque 15,000 Nm Three-phase main spindle motor 40 kW
modernization 2006 Control system 'Siemens' Max working diameter: 700-1500 mm Distance between railway wheels: 1435 mm Regulating distance between railway wheels: 1524 or 1676 mm Length of railway wheels sets: 1640-3000 mm Jaws clamp diameter: 550-1350 mm Max wheel width: 140 mm Spindle turn range: 4 Spindle turn: 9, 13, 5-18, 27 rpm Stepless feed speed range: 1,6-50 mm/min Machine dimensions: 8700 x 3650 x 3250 mm
turning diameter: ca. 500 mm swing diameter: ca. 600 mm travel -x axis: ca. 400 mm travel -z axis: ca. 600 mm spindle turning speed range: 2000 U/min spindle drive: 63 kW control: SIEMENS control: SINUMERIK System 3 tool turret: 1 x 12 Pos total power requirement: kW weight of the machine ca.: 9,3 t dimensions of the machine ca.: m - R-version, turret right hand side of 3-jaw chuck - Accessories: hydr. 3-jaw chuck 400 mmø, various toolholders for turret, chip conveyor, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CNC controlled three-axis under-table cross-cut saw with additional drilling unit for wood and wood-like materials, but also suitable for sawing aluminium non-ferrous metals and plastics. Closed compact production island, low noise pollution and no chips in the machine environment. Our automatic sawing and drilling machine KA 550 CNC - SAW and DRILL is versatile einsetzbar_ – Only saws in automatic mode and for single cuts - Drilling only - Combines drilling and sawing in a single operation The possibilities to work with the drilling unit include drilling and countersinking, combined drilling + countersinking with a combination tool, drill milling of longitudinal holes – longitudinal holes transversely – rectangular cut-outs. The drill feed speed and the drilling pressure can be sensitively adjusted. Technical data Circular Saw and Drilling Machine KA 550 CNC - SAW an ...
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
grinding length: 4200 mm grinding width: 1300 mm workpiece height: 550 mm Control: Siemens 840D passage width: 1300 mm electro-magnetic table: 4200 x 1300 mm grinding height: 550 mm grinding motor: 306 kW grinding motor turning speeds up to: 370 U/min grinding motor feed, infinitely variable: 0,5-35 m/min coolant flow rate: 2000 l/min weight of the machine ca.: 50 t dimensions of the machine ca.: 11,21 x 5,25 x 3,85 m Equipment / Accessories: - segment head - diameter 1400 mm - for segment dimensions 120/106 x 41 x 250 mm - number of segments: 1 set = 26 pieces - grinding motor adjustment - in steps: 0,002 - 1 mm - continuous: up to 5 mm/min stepless The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 0 mm max. number of teeth: 0 max. module: min. module: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m CNC controlled milling machine for synchronous rings The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Working wheel dimensions (od x id x width): Ø610x80xØ304.8 mm, cnc brand: FANUC, CNC brand: FANUC, CNC model: 21 Oi TB, Maximum length between points: 1060 mm, Max travel Z axis: 750 mm, Maximum length to be rectified: 600 mm, Height of points: 225 mm, Ø min/max to be rectified: 10 - 300 mm, Max. piece weight: 125 Kg, Max travel X axis: 325 mm, Grinding wheel speed: 45 m/s, Main engine power: 11 Kw, Workpiece head speed: from 30 to 1000 rpm, Workpiece holder head cone: MORSE 5, Power of workpiece head motor: 12 Nm, tailstock cone: MORSE 4, Travel of the tailstock quill: 70 mm, Hydraulic movement of the tailstock: 150 mm, Total power: 22 Kw, Long: 2300 mm, Tall: 1900 mm, Width: 2634 mm, Weight: 7750 Kg, Accessories: Cooling equipment with paper filter; MARPOSS meter, positioner and balancer;
Generating Grinding Machine Grinding Machine Gleason Pfauter G320 CNC + Promot Automation Hersteller [manufacturer]: Gleason Pfauter G320 + with Promot Automation handling unit Type [ type]: G 320 Control unit: Siemens 840 Incl. control panel Baujahr[construction year]: 10/2001 Module [ ]: 0.5-7.0 Min. workpiece diameter [ ]: 10 mm Max. workpiece diameter [ ]: 380 mm Number of teeth [ ]: 10-600 Vertical carriage stroke "Z" [ ]: 200mm Horizontal carriage stroke "X" [ ]: 230mm Tangential carriage stroke (SHIFTING) "Y" [ ]: 135mm Swivel angle clamping head "A" [ ]: +-45° Tailstock tip stroke [ ]: 125mm tangential slide stroke – dressing [ ]: "V" 180mm radial carriage stroke – dressing [ ]: "U" 110mm Rotation speed – grinding wheel in progress [ ]: 3000rpm max - infinitely variable Egg speed - linear axes [ ]: 10000 mm/min Max. table rotation speed [ ]: 240 RP ...
Max. bar length: 1400mm, bar diameter: 6.35-80mm, weight: 450kg, accessories: cabling, servo amp, bar pusher 52D=12, bar pusher 52D=15, bar pusher 52D=21, with delivery note, copy of the invoice, various manuals, operating and maintenance instructions. An on-site inspection is possible.
groove width: mm x-travel: 1000 mm throat: mm table length: 1300 mm table width: 300 mm total power requirement: 14 kW weight of the machine ca.: 3.2 t required space: 2.9x3.1x2.7 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Horizontal machining centre manufactured in 2004. This IRLE IRD 1600 CNC features a maximum pipe diameter processing capability of 1,625 mm and a maximum pipe length of 13,200 mm. It supports a maximum pipe wall thickness of 70 mm and can handle pipe weights up to 250 kN. If you are looking to get high-quality machining capabilities, consider the IRLE IRD 1600 CNC machine we have for sale. Contact us for further details.
maximum number of results exceeded
please refine your search
 (1).jpg)
