cnc press brake used for sale

Offer 26245 Technical data: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 800 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil capacity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 2980 x D 1850 mm - Weight approx. 4600 kg

The electronic digital tire pressure gauge is a modern device that allows you to quickly and accurately check your car's tire pressure. Auction-ID: A7-50066-139

Pistol grip with 30 cm rubber hose with grease fitting Foot lever Steel drum cover Steel bucket with 6 liter capacity 180 cm high-pressure rubber hose Auction-ID: A7-50066-49

An air dryer with filter and regulator, equipped with a standard 1/4\" air inlet connection. The device is designed to purify the incoming air from most liquid and solid particles. It is equipped with a pressure regulator that allows precise adjustment of the outlet air pressure, from 0 to 150 PSI. Auction-ID: A7-50066-162

Pistol grip with 30 cm rubber hose with grease fitting Foot lever Steel drum cover Steel bucket with 6 liter capacity 180 cm high-pressure rubber hose Auction-ID: A7-50066-149

Pistol grip with 30 cm rubber hose with grease fitting Foot lever Steel drum cover Steel bucket with 6 liter capacity 180 cm high-pressure rubber hose Auction-ID: A7-50066-249

Capacity 4 ton, manual, never used Overall dimensions: 500 x 400 x 800 mm Weight: 50 kg Auction-ID: A7-50066-347

An air dryer with filter and regulator, equipped with a standard 1/4\" air inlet connection. The device is designed to purify the incoming air from most liquid and solid particles. It is equipped with a pressure regulator that allows precise adjustment of the outlet air pressure, from 0 to 150 PSI. Auction-ID: A7-50066-62

Manual gantry press 20 tons Overall dimensions: 1200 x 800 x 500 mm Weight: 100 kg Auction-ID: A7-50066-418

The electronic digital tire pressure gauge is a modern device that allows you to quickly and accurately check your car's tire pressure. Auction-ID: A7-50066-39

CONTROLS   PLC SIEMENS SIMATIC OP 27 PRESS DESIGN   table cushion: yes PRESS FORCES   total force (nominal): 300 to PRESS TABLE   table surface (left-right): 1800 mm   table surface (front-back): 1000 mm SLIDE   stroke: 600 mm SLIDE (HYDR. PRESS)   return force: 38 to DIE CUSHION (TABLE CUSHION)   stroke: 200 mm TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 1000 mm DIMENSIONS / WEIGHTS   total weight approx.: 43000 kg

Dough dividing and knitting machine (bun press) ERIKA RECORD, Type: Erika Automat Type 4 -Very good condition- - little used - For precise dividing and rounding of a wide variety of dough types - 40 - 120g per piece of dough - Fully automatic workflow - Machine parts in oil bath, no lubrication necessary - Easy cleaning thanks to tilting machine head - Incl. 4 knitting plates with 30 troughs each - Dough-friendly operation - Easy to use - Machine made of stainless steel - Instruction manual Technical data: - Number of divisions: 30 pieces - Well size: No. 4 for 40 - 120g - Dough weight: 40 - 120 g - El. Connection: 380 / 3 V, 50 Hz, 3.8 A, 1.5 kW The machine is in mint condition and is immediately ready for use. Inspection and test run are possible by arrangement.

CONTROLS   PLC SIEMENS S7 PRESS DESIGN   drive system: hydraulic   quick die change system: yes   feedstock transport direction: right to left SLIDE   total force (nominal): 400 to   stroke: 200 mm COUNTER RAM   nominal force: 100 to   stroke: 30 mm V-RING   nominal force: 200 to   stroke: 30 mm TOOL DIMENSIONS   lower table (left-right): 650 mm   lower table (front-back): 650 mm   shut height max.: 420 mm   passline opening (free passage in side columns): 420 mm OVERALL SPECIFICATIONS (COIL LINES)   sheet width max.: 500 mm   sheet thickness max.: 12 mm   feed velocity max.: 30 m/min   feedstock transport direction: right to left LEVELLER UNIT   sheet width max.: 500 mm   sheet width (min): 60 mm   sheet thickness max.: 12 mm   sheet thickness min.: 1 mm   integrated feed function: yes STRIP-FEEDER   sheet width max.: 400 mm   sheet  ...

Self-loading baler GRECON DIMTER ProfiPress PP 2500-3HF Working length 2500mm Working width 1300mm Automatic material loading Automatic glue application Shelves heated by a high frequency generator Material thickness softwood min/max 11-60mm Material thickness hardwood min/max 11-40mm Material width min/max 30-150mm Length of the fed material min/max 300-2500mm Year of manufacture 2001 CE Certificate

• Presumably used for punching pipes. • Passage diameter: approx. 450 mm

Incl. foot switch and the bending tool located on the machine. • hydraulic oil volume: 120 l

Incl. hydraulic pump and two roller units.

on workshop trolley

pressure: 135 t chamfer lenght: 3600 mm distance between columns: 3150 mm stroke of upper beam: 200 mm ajustment speed: 70.0 mm/sec working feed: 10.0 mm/sec return speed: 80.0 mm/sec : 315 bar dayligth: 400 mm table height: 915 mm column arm: 250 mm engine output: 15.0 kW weight: 8800 kg range L-W-H: 4200 x 1700 x 2600 mm Equipment: - Electro-hydraulic press brake with torsion bar - HACO NC control (Model ATL 550) for X and Y axes Computer-controlled multi-axis NC press Backgauge position pre-selection (electric backgauge) Backgauge retraction for Z-bends Bending depth pre-selection Electric depth adjustment Memory for 200 programs - Swiveling control panel (front left) - NC motorized backgauge (X-axis) with 2 manually adjustable stop fingers - NC motorized depth adjustment (Y-axis) - 1x set of sectionalized gooseneck (swan-neck) upper tools - 1x rotatable MULTI-V die block - Re ...

pressure: 60 t throat: 280 mm stroke: 10-90 mm no. of strokes: 110 Hub/min ram - range of adjustment: 60 mm table surface area: 750x540 mm ram surface: 600x200 mm hole in the table: 300x200 mm table height: 780 mm tool hole in ram: Ø35 mm weight of the machine ca.: 3,7 t dimensions of the machine ca.: 1800x1800x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t stroke: 380 mm table-size: 800 x 700 mm working speed:: mm/ sec. return speed: mm/sec work height max.: mm total power requirement: 4,0 kW : 90 mm weight: 2,5 t dimensions: 2,2 x 1,4 x 1,6 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CONTROLS   PLC SIEMENS S7 SLIDE   total force (nominal): 630 to TOOL DIMENSIONS   lower table (left-right): 900 mm   lower table (front-back): 900 mm   shut height max.: 900 mm

pressure: 93 ( 100 ) t stroke: 165 mm table surface area: 990 x 400 mm total power requirement: 1 kW weight of the machine ca.: 1 t dimensions of the machine ca.: 2 x 1 x 2,2 / 2,7 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2025 : 070145 : prompt, Zwischenverkauf v : Türkei : 44500 € : 849.95 € : 1 : 40 to : 4 mm : 630 mm : 450 mm : 160 mm : 3 - 75 mm : 154 1/min : 420 x 275 mm : 8 : 75 mm : 40 mm : 230 mm : 293 mm : 4 kW : 1174 mm : 1540 mm : 2200 mm : 2850 kg 8-fold ram guide 2-hand control panel and foot pedal Automatic central lubrication Front light guard Vibration pads User Manual in German with CE Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specially designed for stamping, die cutting, and forming work. Model CM-50NC Power 50 TN Motor power 5.5 KW Throat depth 265 mm Working speed 9.9 mm/s Approach speed 50 mm/s Return speed 66 mm/s Maximum pressure 320 bar Piston stroke 250 mm Lower table 700 x 450 mm Upper table 550 x 300 mm Maximum vertical light 400 mm Working height 850 mm Total front 1.160 mm Total lateral 1.290 mm Total height 2.085 mm Weight 1.750 kg STRUCTURE AND TABLES The CM/NC series hydraulic presses consist of an electro-welded structure made exclusively of S355JR steel. It is stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. Calculated and designed with finite element software. With all this, we always guarantee our high standards of precision and quality. They are equipped with an upper table and a lower table made of C45E ste ...

TECHNICAL DATA: Working area: 3000 x 1300 mm Pressure plungers: 06 Press piston with Ø 70 mm (stroke 260 mm) 02 Reciprocating piston with Ø 40 mm (stroke 270 mm) Stop piston: 04 Piston for closing with Ø 70 mm (stroke 260 mm) 02 Opening piston with Ø 40 mm (stroke 270 mm) Installed power: 22 kW EQUIPPED WITH: Loading bench with pusher Discharge bank Boiler for heating diathermic oil

GUILLEM ECCENTRIC PRESS mod. 3RPE 125 USED REN DESCRIPTION Highly robust NECK eccentric press with pneumatic clutch and cushion. Includes acrylic front safety doors with magnetic sensor to ensure safety in use. FEATURES Maximum force (pressing): 125 Ton. Maximum number of strokes per variable minute: 47 g/min Stroke variation: 16 / 190 mm Crank adjustment: 80 mm Pitch between uprights: 450 mm Vertical span: 510 mm Pneumatic cushion: 12 tn Cushion stroke: 45 mm Central drill lower table: 275 mm Sliding drill diameter: 60 mm Sliding top table: 370 x 600 mm Bottom table: 760 x 1000 mm Main motor power: 7.3 kw Dimensions: L 1800 W 2000 H 3100 MM Machine weight approx.: 8000 kg Year of manufacture: 1995

Nuts, and so on; Includes 7 plastic stacking crates with dimensions 400 x 600 mm Auction-ID: A1-49785-374

Reference: 744-05; own weight approximately 100 kg Auction-ID: A1-49785-260

Reductions, and so on; In 17 cardboard boxes Auction-ID: A1-49785-375

2 PSC. UHP units - 1 Watertank 2000 l and 1 Fuel tank 1800 l Performance: 2 x HAMMELMANN HDP 170 units with 2 x pressure steps: 1- 2900bar 29l/min 2 - 3000bar 27l/min Diesel Engine = Caterpillar 3126B ATAAC The units has always been maintained as they should. The units are running and performing as they should. Sold without any warranty.

High-pressure cleaner, hot water high-pressure cleaner -Manufacturer: Ehrle, Hot water high-pressure cleaner -Type: HD 1140 Electronic II -Operating pressure: 30-230 bar -Spray flow rate: 16 l/min / Steam setting: 7 l/min -Hot water output: 30-98°C / Steam setting: 150°C -Power connection: 3/PE/AC/50Hz/400V -Cleaning agent: High-pressure jet application and quantity control -Dimensions: 1200/800/H1000 mm -Weight: 225 kg

CONTROLS   electronic controls PRESS DESIGN   number of suspensions: 2   opening in table: yes PRESS FORCES   total force (nominal): 45 to PRESS TABLE   table surface (left-right): 550 mm   table surface (front-back): 450 mm SLIDE   slide force: 45 to   table surface (left-right): 550 mm   table surface (front-back): 360 mm   stroke: 50 mm   stroke rate (max.): 400 /min SLIDE (MECHAN. PRESS)   slide adjustment: 50 mm   stroke min.: 10 mm   stroke max.: 50 mm   stroke rate (min.): 80 /min   stroke rate (max.): 400 /min TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 305 mm Grid 2016 Completely Overhauled

pressure: 4000 t stroke: 380 mm dayligth: 1050 mm distance between columns: 1580 mm table-size: 1520 x 1600 mm dimension of ram: 1470 x 1500 mm ram adjustment: 15 mm strokes of ram per min.: 50 ejector path: 31 / 70 mm main drive: 200 kW height over floor: 7520 mm total power requirement: ca. 250 kW weight of the machine ca.: 245 t dimensions of the machine ca.: 4,4 x 4,6 x 7,5 m complete forging line includes an - Smeral Hot Forging Press - induction heater - Manyo 460-millimeter forging roll - manipulator with forging roll link - SMERAL 500-ton trimming press The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 50 mm bending angle max. +/-: 180 ° bending radius max.: 350 mm bending speed: 3 U/min motor speeds:: 2815 U/min bending radius max.: 350 mm bending angle max. +/-: 180 ° tool taper: Sechskant 40 mm total power requirement: 2,2 kW weight of the machine ca.: 0,1 t Machine Type Electric Bending Machine Model 6000-S Power Connection 3-phase 400 V Control System JUTEC electronic, programmable bending control with display and membrane keypad Operation Foot switch for clockwise/counterclockwise rotation and bending operation Design Mobile machine on swivel casters The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: ca. 60 mm tool taper: Sechskant 40 mm bending device: horizontal bending speed: 3 U/min weight of the machine ca.: 120 kg total power requirement: 2,2 kW Electronic bend angle control Digital display and keypad Operated via dual foot switches Mandrel-less bending Mobile machine base Pipe diameter range likely up to Ø 60 mm Tool mounting via hexagonal shank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Slaan: - 29 x 15 mm - 34 x 12 mm - 20 x 20 mm - 57 x 8 mm Scheren: - 230 x 20 mm - 375 x 10 mm Hoeksnijden: - 90°: 130 x 13 mm - 45°: 75 x 10 mm Doorsnede snijden: - rond: 45 mm - vierkant: 45 mm - C amp; I profiel: 127 mm Inkepingen: - rechthoekig: 45 x 100 mm Punching pressure: 60 ton Max sheet thickness by punching + nibbling: dia 29 x 15 / dia 57 x 8 mm Max punching dia: dia 160 mm Power needed: 5,5 kW Length: 1640 mm Depth: 710 mm Height: 1780 mm Weight: 1570 kg

Manufacturer: KAISER Model: V200 WR Year: 1983 Condition: Used Stock Number: 9535 Compressive force: 200 t Table length: 1450 mm Table width: 900 mm Maximum stroke rate upper table: 150 1/min Adjustment of the ram: 100 mm Ram stroke: 20-120 mm Equipment: Sheet metal straightening roller Unwinder Workpiece feeding

pressure: - t distance between columns: - mm stroke: - mm total power requirement: - kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Digital pressure transmitter with oil-free ceramic membrane for measurement in gases and liquids for measuring pressure, level, volume or mass. Signal output 4-20mA, voltage 11.5-45V DC, measuring range up to -1/0 ... 40 bar. Connection DN50 flange.

Digital pressure transmitter with oil-free ceramic membrane for measurement in gases and liquids for measuring pressure, level, volume or mass. Signal output 4-20mA, voltage 11.5-45V DC, measuring range up to -1/0 ... 40 bar. Connection DN50 flange.

Digital pressure transmitter with oil-free ceramic membrane for measurement in gases and liquids for measuring pressure, level, volume or mass. Signal output 4-20mA, voltage 11.5-45V DC, measuring range up to -1/0 ... 40 bar. Connection DN50 flange.

MODEL SL-150 Power t 150 Motor power kw 4 Piston stroke mm 250 Working speed mm/s 3.1 Return speed mm/s 4 Head displacement mm 1,000 Front light mm 1,500 Side light mm 340 Max. vertical span mm 955 Bed light mm 405 Total front mm 2,150 Total side mm 1.180 Total height mm 2.805 Weight kg 2.350 STANDARD DESCRIPTION: The S-series hydraulic presses are specially designed for extraction, casing and straightening work. They work with a hydraulic pressure of less than 320 bar, which guarantees greater durability of the entire hydraulic system. STRUCTURE: They consist of an electro-welded structure with four uprights with open sides. They are equipped with a movable bed that allows it to be positioned at different heights. The fixing is done by means of two pins located at the bottom of the bed. The raising and lowering system is carried out by means of cha ...

The machine is in good technical condition; it can be tested by prior arrangement.

The machine is in good technical condition; it can be tested by prior arrangement.

STANDARD FEATURES: Power 50 t Motor power 1.5 kw Working speed 2.25 mm/s Return speed 4.50 mm/s Maximum pressure 500 bar Piston stroke 150 mm Spindle stroke 120 mm Front light 800 mm Side light 160 mm Max. vertical span 1,020 mm Bed light 205 mm Total front 1,090mm Total side 900 mm Total height 2,000 mm Weight 295 Kg. Specially designed for extraction, bushing, straightening, etc. The hydraulic presses of the S series consist of a four-pillar electro-welded structure with open sides. They have a movable base that allows it to be positioned at different heights. The fixing is by means of two pins located at the bottom of the bed. The raising and lowering system is by means of chains driven by the cylinder of the press. SD Models: are fixed head. Double-acting cylinder with chrome-plated plunger and anti-wear guides. It is equipped with a removab ...

Manufacturer: ERFURT Model: PKnT 160 Year: 1978 Condition: Used Stock number: 9542 Compressive force: 160 t Maximum stroke rate upper table: 15 1/min Ram stroke: 200 mm Adjusting the ram: 130 mm

TJF-GARNET SPECIAL HYDRAULIC PRESS: Hydraulic press with double upright equipped with two side cylinders joined by a plate for the pre-pressing and pressing of rotors and stators, and a central cylinder for the extraction of the mandrel and stalling of the rotor shaft, as well as the extraction of shafts in case of repair. It has a removable table for the stacking and handling of rotors and stators. MAIN CYLINDERS 150 TN.  2 hydraulic cylinders of 75 Tn. of power each, with a stroke of 1200 mm joined by a grooved plate, with a central bore of 250 mm in diameter.  Maximum useful height cylinder plate of 1550 mm.  Minimum useful height cylinder plate of 350 mm. ABSTRACTION CYLINDER  1 central cylinder of 80 Tn of power with 1200 mm stroke.  Prepared to adapt abstraction clamp, end of threaded stem to M 35,150 x 40 in length.  Maximum useful height ...

USED GAMEI OBR-140 ECCENTRIC PRESS FEATURES: MODEL OBR-140 Nominal capacity 140tn Strokes per minute 90 approx. Adjustable stroke 17-142 mm Lower table 1,140 x 770 mm Top table 480 x 800 mm Vertical span between tables 650 mm Working height 945 mm Sliding spindle regulation 140 mm Main motor 11 kW It can be supplied with or without CE adaptation.

Key data: 1250 t

Manufacturer: Dieffenbacher Model: PO-F 1250 A Year: 1979 Condition: Used Stock number: 9543 Control system: Siemens Simatic HMI Compressive force: 1250 t Table length: 1250 mm Table width: 1250 mm Stroke: 630 mm The general overhaul was carried out in 2015.