cnc automatic punching used for sale

8-spindle rotary machine Built in 1989; serie 25 Refurbished in 2012 • New electrics • New bearings • Guided tours • CNC cross slide in position 7 • Spindle stop setup • Material rod guide • Chip conveyor • Pick-up spindle position 8 • Calibration device • Various tool holders • Various curves

Neri BL400 VTE tamper-evident labeller for the application of 2 self-adhesive tamper-evident seals on the closure points of formed cartons and 1 vignette/bollini label or similar on the upper face of the carton. Specifcation: - Labelling machine balcony construction stainless steel executed. - Electrical cabinet on machine board, Siemens S7-300 PLC controller with HMI touch screen - Laetus Argus 6012 bar code reader - Easy access from behind to electrical and mechanical parts - Positive transport of cartons with toothed belts. - Upper conveyor belt to keep carton stable during tamper evident seals application - Twin horizontal conveyor belt for products bunching at in-feed. - Mechanical timing device to dispense cartons on the main toothed conveyor belts. - Label dispensing with stepping motor drive. - Automatic work speed synchronization of motors. - Label length self-le ...

Graham labeler COUV 128-40 with tripod, Y.O.M. 2001

Available for sale 2 x NEVER USED Leroy Somer Automatic Voltage Regulator R713. The 3F R713 or R723 modules are used in connection with a R200 series regulator for equalizing the voltage of an alternator with that of the network before coupling, when the installation operates automatically or when manual equalization of these voltages is not possible. This prevents excessive current caused by coupling a network to the machine when both are not at the same voltage. This difference in voltage is usually due to fluctuations in the network voltage because the alternator is regulated at a constant voltage except for cases of voltage droop). On some networks these fluctuations can reach ± 10%. Equipment never used and in good working conditions. Consumption: < 2VA Response time: < 300 ms Dissipated power: < 1W Temperature Shift: 1% of Un for delta T ambient variing from -20° to 2 ...

Note: We have 6 pieces of this machine in stock! Manufacturer: Gildemeister Type: GS 36 – 6 A/C Machine no.: 7.0176 Year of construction: 1987 Weight: 11t General / technical data: Portal-6spindle automatic lathe with measuring device and automatic feeding Spindle dividing circuit: 300mm Number of longitudinal slides: 6 Number of cross slides: 2 gr. cross slide stroke: 60mm gr. longitudinal slide stroke: 125mm Spindle speeds: Infinitely variable 562 – 3373 rpm Main time range: Stepless 1.95 – 78 sec. Low time range: 0.79 – 2.13 sec. Drive power: DC motor spindles 20kW; Feed rates 8kW Installation area: approx. 1720 x 4700mm Remark: The machine cannot be converted for bar work. Equipment: – 1 creep gear drive for set-up operation – 1 automatic central lubrication device – 1 coolant device with lines and pu ...

We are here to provide an L type automatic sealing machine, which is widely used in a variety of industries due to various reasons. Our machine is available in a variety of specifications. A loading and cooling zone is supplied as standard output. A heat-resistant, powder-coated carrier was used. It is very easy to install and easy to use. Conveyor roller made of stainless steel and silicone coated. Power-coated tunnel covers for heavy duty and an electrical control panel are included. Capacity: 50 pieces/min Voltage 380V/50-60Hz/3-phase Main Material: Stainless Steel The internal circuit type is suitable for PVC. PP. POF packaging material. Extra-long shrink tunnel, intelligent temperature controller with figure and closing heat wind inner circuits.

Automatic filling plant Logdos Späth GmbH Type K-DOS. F/AL 40/ EX EX protected mobile on wheels Programable X/Y axis and pallet image Very good condition, directly from production!

KROENERT PACK 600 WITH TPC type KRA 250 water Chiller Coating and Laminating Machine PAK 600 For following operations: Wax Laminate / Coating - one sided 2 - 30 g/m2 Hotmelt Coating at temperature 10 - 40 g/m2 For the following materials: Unclad Aluminiumfoil 9 -150 my Flexible films like PE, PP, PVC, PVDC, PVA, Polyester and Polyamide films. Cellophane and cellulose acetate films Paper and material combinations. Max Mechanical speed V = 100m /min Realisable speed depending on material and application grammage. The Complete drive assembly was overhauled in 2016 for R 1.2 million.

Bertolaso Athena 75/15 Vacuum filler Bertolaso Year: 1991 with 75 filling valves and 15head aluinium screw capper Running direction: left to right

Libra / labeler Bizerba GV 7000, built 1999, in a very good used and functional condition. Fully automatic scale with labeler / price printer, programable, feed and feed belt. Dimensions W/D/H 260/65/170 cm. Operating voltage 230 volts, compressed air connection 6 bar required. Workshop-tested, ready for immediate use. More on request.

Consisting of: 1 Fully automatic depalletizer, Krones Palmaster 1 Fully automatic palletizer, Kettner Pressant duplex 1 Pallet magazine 1 Pallet control Pallet turning stations Pallet conveyors Protection fence Further information: Equipped for Euro-pallets. With Siemens S7 control. Year of construction: 1995 The line is currently in production. A viewing is possible. Composed of: 1 Fully automatic depalletizing, Krones Palmaster 1 Fully automatic palletizing, Kettner Pressant duplex 1 pallet magazine 1 pallet inspection Turning stations / corner converters Pallet transporters Protective fence Further information: Equipped for Euro pallets. With a Siemens S7 controller. Year of construction: 1995 The line is currently still in operation. A visit is possible by arrangement.

Schuette Multi-spindle rotary machine Name: Schuette SF 20-6 Curve controlled Number of spindles: 6 Built: 1980 max. rod diameter: around 20 mm SW 17 mm AK 18 mm VK 14 mm max. rod feed: 80 /(160) mm Number of independent Laengsschlitten: 6 Total / working distances (stand): 63/40 mm " " (special) up to: 100/63mm Number of independent cross slides: 6 Total/ work routes Medium and top slide up to: 32/20 mm Slide up to: 40/25 mm Spindle circle diameter: 224 mm Main times min/max.: 0.36/150 sec. Gv29e0 Off times min./max.: 0.45/0.80 sec. Spindle speed from / to: 900-5000 rpm in the 2nd area: 355-2000 rpm Rated power of the drive motor: 15 KW Connected power: 50 kVA Drive engine speed: 1500 rpm Length Width (in standard performance) 3705 1320 mm incl. rod guide (in standard output) 6335 mm Weight without ro ...

Schuette multi-spindle rotary machine SF 26-6 1980 built -with thread cutting device - prepared for centrage suction system - standard Schuetz control D8gdo29 - mechanical gearbox - Balluff cam switch - standard rod guide

Thread cutting gear Pick-up device partially revised

Rotary table polishing machine make Bula, model MP81 for sale. Continuously circulating machine for polishing, brushing, grinding and deburring a wide variety of workpieces. 6 workpiece holders mounted in a pitch circle of 250 mm. 1 processing station, drive power 2.2 kW, with Bula Quick Lock system of polishing wheels. Polishing shaft diameter 25 mm The machine has been completely overhauled, machine body sandblasted, primed, repainted, new bearings, new motors, new gearbox, new V-belts, new handwheels, new pulleys, completely new control cabinet, and all drives are controlled by frequency converters. Subject to prior sale. Optionally, the system would also be available with a polishing paste system - liquid, consisting of 1 high-pressure dosing guns WIDOBERG HDP-2, holder, timer, etc. and pressure container.

Gildemeister 6-spindle rotary machine, curve controlled max. rod passage: 32.0 mm for rods up to 3.30 m - incl. rod guide, - Steel processing, run with cutting oel - easily equipped with tools Cmvlgfoyc - 1 set of clamping and feed pliers - Alternating wheels (on machine) - 1 set of curves for cross slides - 1 set of curves for main slide

Schuette multi-spindle rotary machine SF 50/51-6 Rod turning machine run on schneidoel standart Schuetz control mechanical gearbox Hydraulics integrated into the machine with snail-spaenefoerer

Schuette multi-spindle rotary machine SF 26-6 1984 built - mechanical gearbox - independent feed from the Laengsschlitten Position 4 - Thread cutting gear with thread cutting spindle

Gildemeister 6 Spindle Lathe AS 32-6 - Spindle stop set-up - Pneum pick-up device. - Zubehoer at an extra cost - Cross hole drilling - Thread cutting gears - Thread cutting device - wahlw. Fraeseinrichtung Querschl. - Spaenefoerderer

Schuette Multi-spindle rotary machine Name: Schuette SF 20-6 Curve controlled Number of spindles: 6 Built: 1984 max. rod diameter: around 20 mm SW 17 mm AK 18 mm VK 14 mm max. rod feed: 80 /(160) mm Number of independent Laengsschlitten: 6 Total / working distances (stand): 63/40 mm " " (special) up to: 100/63mm Number of independent cross slides: 6 Total/ work routes Medium and top slide up to: 32/20 mm Slide up to: 40/25 mm Spindle circle diameter: 224 mm Main times min/max.: 0.36/150 sec. Off times min./max.: 0.45/0.80 sec. Spindle speed from / to: 900-5000 rpm in the 2nd area: 355-2000 rpm Rated power of the drive motor: 15 KW Connected power: 50 kVA Drive engine speed: 1500 rpm Length Width (in standard performance) 3705 1320 mm incl. rod guide (in standard output) 6335 mm Weight without rod guide a ...

Gildemeister 6-spindle rotary machine, curve controlled max. rod passage: 32.0 mm for rods up to 3.30 m - incl. rod guide, - Steel processing, run with cutting oel - easily equipped with tools Sowiabeb - 1 set of clamping and feed pliers - Alternating wheels (on machine) - 1 set of curves for cross slides - 1 set of curves for main slide

Schuette SG 18-6 with gantry loader as feed lathe alternatively conversion possible as a rod lathe, incl. spindle stop setup Location 3+4 with extended stroke CNC cross slide on layer 5 Etc. Machine is ready for use and can be visited under electricity loading device is not currently connected.

Schuette multi-spindle rotary machine SF 26-6 1987 built 6-spindle rod turning machine with hydraulic catch slide prepared for Co2 Loesch plant run with cutting oel Schuetz control mechanical gearbox separate hydraulic unit -- Pick-up device with hydraulic voltage and back-weighing machining without Spaenefoerderer standard pole guide unabhaenger Laengsschlitten feed to position 1,2,4,5 ...

Gildemeister Multispindle Slot machine 6- Spindler Type: AS 25-6 Pick-up device back-valued processing pneumatic stop Balluff cam switch IEMCA PRA Bar loader Oil mist separator (electrostat.) Conveyor Machine has been retrofitted in the past

Index HE 25 with rod feed hydraulically controlled with long turning device

Mechanical high-efficiency automatic press Pressing force: max. 150kN Ejection force: 50kN Die support in pressing position: max. 150kN Return force of lower punch: max. 32kN Closing force of upper punch: max. 12kN Upper punch stroke: 90mm Upper punch adjusting travel: 60mm Stroke rate: 8...40strokes/min

Overhaul year 2020 Built 1995-2019 Saw blade 160 - 200 mm Drive power saw motor 2.2 KW Speed Saw blade 1,500 -3,750 min-1 Cutting speed Saw blade 750 - 3350 m/min Saw height control infinitely adjustable fully electronic Working area square 90° max.: 50 x 50 mm Working range flat 90° max.: 110 x 50 mm Working area Around 90° max.: 50 mm Supply length Pneumatics 2.5 - 350 (single stroke) 5 - 700 (double stroke) Supply length AC Servo 2.5-9999 mm (optional) Supply supply. Servo-controlled replenishment unit 500 mm/s Compressed air connection 6 bar Weight (saw) approx.: 600 Kg Dimensions LxWxH (saw without attachments)approx.: 1400mm x1000mm x1600mm Technical Description Pressta Eisele Profilma 200 Retrofit Pressta Eisele Profilma 200 Retrofit Fully automatic high-performance sawing machine for non-ferrous metals and material The machine is technically as well as ...

with rod pipe

various accessories / spare parts for Tornos AS 14

Motor three-phase current 400V with frequency converter (kW) 3 Saw blade dimension (mm) 5200 x 34 x 1.1 Flywheels Ø (mm) 480 Cutting speed (m/min) 20 – 120 Wingspan (mm) 610 Working height (mm) 780 Machine dimension without packaging (mm) 2780 x 1440 x 1560 Weight (kg) 800 Standard equipment Ergonomically redesigned, robust welded frame construction for mitre cuts from 0° to 60° right/left Stable, low-vibration frame construction with arm joint mounted in plain bearings Clear control panel to the operator side Simple, easy-to-understand controls Precisely ground carbide saw blade guides (adjustable) for the highest demands on cutting accuracy Synchronously driven chip removal brush Semi-automatic sawing cycle: fully hydraulic Cutting feed hydraulically incl. automatic cutting pressure regulation Mitre adjustment and clamping (manual) Hydraulic Full Stroke Cylind ...

BIESSE - Multi-spindle drilling machine Model BEAVER Year 1982 Manufacture Biesse S.p.A Italy S/N 312/82 Technical data 1 horizontal drilling unit, 21 spindles 2 vertical drilling units, 2x10 spindles, pitch 32 mm horizontal Drilling motor 2.2 kW Vertical drill motor 2 x 1.5 kW Spindle speed 2800 rpm Blade dimensions 10x1.5 mm Operating pressure 0> 6 MPa 7 pcs. pneumatic answers with kSsi control levers Weight 865 kg L x W X H 280cm x 150cm x 150cm

E.C.H WILL ROTEX – TRI Year: 1987. One real stand. Diameter 1.2 max width 96 cm 4 hole perforation Print 2/2 Cross cutter 2 cover feeder Counting and collecting, Stitching unit Folder, Square back press. Long side cutting/short side cutting Speed: 400 m/ min Max 60 stroke/ min Cross Cuter: 300 mm, 355 mm, 420 mm and 455 mm From spare parts have gears for sheet count, knifes, stitching heads, printing cilindars.

Machine type: Automatic band saw - Horizontal Manufacturer KASTO Type KastoTwin A4 Year of construction 2002 Country of origin Germany Delivery time by arrangement Freight base from location Technical details Cutting diameter 400mm Saw blade length 5,090mm Cutting width 1.3mm Cutting range at 90 degrees: around 400mm Cutting area at 90 degrees: square 400 x 400mm Smallest diameter 10mm Smallest section length 6mm Feed length 750mm Cutting speed 20 - 110m/min Clamping pressure 20 - 60bar Saw blade dimensions 5,090 x 41 x 1.3mm Total power requirement 7.0kW Machine weight approx. 1850 kg Space requirements approx. 2400 x 2500 x 1700mm

Semi-automatic flocking system The system is used for coating and with different materials. It is also conceivable to use it as a painting system. In this particular case, the inner parts were coated by handheld compartments for the automotive industry. The handheld boxes hung on a chain conveyor belt and were first sprayed with glue by hand. Afterwards, the boxes were sprayed with the flocking material in the individual flock cabins. The spraying direction changes from station to station.

FMB JUPITER band saw was manufactured in 2000 in Italy by FMB s.r.l.. The machine, designed for precision cutting of workpieces, is an indispensable tool in any production facility. The machining process is performed fully automatically by means of a high quality 3180 mm long saw blade, which is driven by a powerful electric motor with an stepless gearbox and transmission wheel. The robust design also eliminates any vibration generated during machining, guaranteeing exceptional stability, even during the most intensive production work. In 2024, the FMB automatic band saw underwent an upgrade, during which the control panel was replaced with a new one. The FMB JUPITER bandsaw weighs 1150 kg. Technical data of the FMB JUPITER metal band saw - cutting angle: 0°-60° - cutting capacity (0⁰, circle): 240 mm - cutting capacity (0⁰, square): 240x240 mm - cutting capacity (0⁰, rect ...

Semi-automatic flocking system Flockkabine MAAG flocking technology The system is used for coating and with different materials. It is also conceivable to use it as a painting system. In this particular case, the parts were coated for the automotive industry.

PLC – controlled high-performance precision cold-circuit sawing machine with very high quality loading magazine – equipped with software for industrial production in accordance with Industry 4.0, designed for the precision cutting of steel and stainless steel rods – high-strength alloys – forged materials and similar materials and similar materials Saw blade dimensions 460 mm x 2 mm to 2.5 mm, maximum cutting range 0° - 150 mm or 130 x 130 mm - saw blades made of TCT material are normally used (TUNGSTEN CARBIDE TIPPED) - this material allows very high cutting speeds and low saw blade thicknesses, which significantly limits the material loss, saw blade speeds 60 to 130 rpm, controlled unloading slide for two different unloading positions, largest bar length in the loading magazine 6,000 mm, maximum material weight in the loading magazine 3,000 kg, largest material feed per fee ...

Semi-automatic flocking system Flockkabine Manufacturer: The system is used for coating and with different materials. It is also conceivable to use it as a painting system. In this particular case, the inner parts were coated by handheld compartments for the automotive industry. Plant size: Width: approx. 6.5 m Depth: approx. 2.8 m Height: 3, 3 m Lock doors Width: approx. 900 mm Height: approx. 600 mm

Capacity: 6,000 - 8,000 cups/hrs Number of tracks: 4-lane longitudinal runner Closure: Sealing Schuy + Folmeg Maschinenbau GmbH is happy to overhaul this system for you. All electrical and pneumatic components are brought up to date and mechanical components are overhauled and 80% of new quality is available. You will also receive a 1-year warranty for the system. Please contact us.

Type: SCHRÖDER N 82 Number of needles: 82 Diameter of needles: 3 mm Product width: 420 mm Transportation type: walking beam Product passage height: 180 mm Brine pressure: 0,5 – 4,0 bar Machine dimensions in cm: Width: 110,0 Width with filter for brine: 200,0 Length: 210,0 Height: 200,0 Compressed air: 6bar Power: 9,0 kW, 15А Voltage: 380 V, 50 Hz

PLC – controlled high-performance precision cold-circuit sawing machine with loading magazine and unloading magazine of very high quality - equipped with software for industrial production in accordance with Industry 4.0, designed for the precision cutting of rod material – tubes and hollow profiles made of steel and stainless steel Saw blade dimensions up to a maximum of 315 mm x 2 mm to 2.5 mm, maximum cutting range 0° - 12 mm to 80 mm tubes and hollow profiles - 12 mm to 40 mm solid material - saw blades made of TCT material are normally used (TUNGSTEN CARBIDE TIPPED) - this material allows very high cutting speeds and low saw blade thicknesses, which significantly limits material loss, saw blade speeds 20 to 130 rpm - optionally available with different saw blade speeds, controlled unloading unit for four different unloading positions - largest automatically unloadable sectio ...

Pallet feeder – separating head Vaculift - Vacubelt 6 buckles Gate fold Compressor Without delivery

Cutting area round: 250 mm Cutting area rectangular: 250 mm Saw band dimensions: 3660 x 25 x 0.9 mm Band speed: 20 - 70 m/min Saw drive: 1 kW Space requirement: 1900 x 1450 x 1250 mm Weight: approx. 850 kg

press is after overhaul: full function complete mechanical parts, pneumatic and control system. The press has a new pneumatic clutch, the original was electromagnetic clutch as old system. Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 5000 kg

Böllhoff Uniquick Vario automatic screw feeder UNIQUICK Feeder Type 360 Plastic sorting pot ∅ 360 mm Quiet and surface-friendly conveying Optimal spiral dimensioning depending on the material to be conveyed (width and height) Integrated and controlled chicane High wear resistance Uniform flow rate due to amplitude control In a soundproofed housing on a frame Web width: 20 mm Head Ø of the fastener up to 20 mm Length of the fastener up to 55 mm Filling volume: 3 l SIM BB-10-C (ws) Tape Bunker Bunker trough, chute: stainless steel Strap: white with FDA approval Filling volume: 10 litres Max. filling weight : 35 kg Drive: AC gear motor 230V/50Hz Bunker with innovative drive to ensure metered, quiet and part-friendly feeding of screws and connecting elements. UNIQUICK Multi Modularly expandable 3-fold crossover Distributes the tested screws to three st ...

GERDA HYDOMAT PAWN 100 automatic press was built by GERDA HYDOMAT S.A. in Poland in 2001. The machine, with a high press force of 100 tonnes, is dedicated to the mass production of precision steel parts. All machining processes, i.e. precise stamping and threading of the workpieces, are performed fully automatically. The sheet metal feeder accurately feeds the material into the workspace, where the slider and reliable threading head are located. The design, which is made from the highest quality raw materials, in turn maintains the highest stability during even the most intensive challenges. The GERDA HYDOMAT hydraulic press weighs 5200 kg. Technical specifications of the GERDA HYDOMAT PAWN 100 press - press force: 100 t (1000 kN) - work table dimensions (L x W): 700 x 320 mm - height of working space: 250 mm - slider stroke: 0-70 mm - number of slider strokes: 10-40/min - numbe ...

1st unit : M7/46 – 2 buckles 2nd unit : M7/46 – 2 buckles SBAP 46-ME-52 delivery

ID3599 Aquachem Automatic filter machine / Filterautomat AF 800 year/Baujahr 2020 Automatic filter machine, Filter volume: 154 dm3, filter area: 9.9 m2, filter plate format: 800 x 800 mm, number of chambers: 10, cake thickness: 32 mm, plate type: sealed chamber and membrane plates, feeding: up to 8 bar via the external inlet at the top, membrane repressing: pneumatic repressing system with internal air distribution and ramp-controlled pressure build-up (max. 15 bar), cake emptying system: AIRDIS cake emptying system and vibrating cylinder integrated in the filter plate handle, press locking: automatic, self-regulating electric/pneumatic/hydraulic locking system, drive: 0.75 kW, 400 V, 50 Hz, with control system, with connection and drain distributor, feeding unit (peristaltic pump), rinsing station, only in use for 1 year Automatic filter, filter volume: 154 dm3, filter area: 9.9 m2, ...

specifications: Up to 400 PCS/MIN, 8 sealing heads, continuous rotary sealer. Vial diameter (mm) DF: Min 14, Max 52. Vials height (mm) HF: Min 35, Max 110. Cap diameter (mm) DC: Min 13, Max 33. Cap height (mm) HC: Min. 6, Max. 16. Power: up to 400 rpm. Standard voltage: 400V - 50 Hz.

Stock# UG6391 Automatic machine for lipstick filling Manufacturer: Cosmatic Model: SM43 Slim Working output up to 2000 pcs/h Device works in silicone mold technology (Long rubbers). Possibility of producing slim lipsticks with an oriented stick. Air cooled. Machine has two refrigeration compressors working alternately. Silicone mold heating by hot air blower (inside) and electrical lamp (outside). Additional heating to prevent the formation of a cone inside the lipstick. Automatic insertion of the stick into the packaging. Automatic screwing station. Manual package loading. Manual capping. Machine equipped with 2 filling heads and melting/dosing pumps. Machine fully functional and still in use. Regularly serviced. New 2016.