cell used for sale

Weight: 1.45t, with Industrial Robot Fanuc M20 iA, max. load: 20kg, the system has been idle for three years already.

Key data: 630 , 630 , 710

- X: 630 mm - Y: 630 mm - Z: 710 mm - speed range: 12.000 rpm - tool changer: 40 -station - B axis: Ø 525 mm - 360 ° - coolant system: yes - chip conveyor: no - tool holder: HSK 63 - control: MTX (Bosch Rexroth) - total power: 30 kW - weight of machine: 11.000 kg - space requirement (W x D x H): 7,0 x 2,0 x 3,2 m - condition: very good Details High-speed machining center with horizontal main spindle, direct measuring systems in all axes, feed speeds X / Y / Z: 60 m / min., B: 60 1 / min, max.forces (X / Y / Z): 17.5 / 20 / 17.5 kN, main spindle (Weiss GmbH), hardly any operating hours, was only used for research purposes at a technical university

rolling capacity max.: NA t workpiece diameter: 38 mm workpiece length: 500 mm total power requirement: 24 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. Originally, external gears were formed on the machine using  ...

x-travel: 1250 mm y-travel: 1000 mm z-travel: 1000 mm B-axis (table): Table dimensions: 800x800 mm Table load: 2500 kg table indexing - automatic: 360 ° rapid travel - grinding spindle: 15 m/min Feed: 1-15000 mm/min feed power: 23000 N : 10 min-1 spindle drive: 34 kW max. torque on the spindle: 1644 Nm turning speeds: 10-4500 U/min transmission ratio: 3 spindle diameter: 130 mm spindle taper ISO: 50 Tool changer: 40 Control: Siemens type: 810 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

centre distance: 1200 mm : 550 weight of the machine ca.: 2,5 t multifix: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

General SKU099Z410 LocationBarneveld MakeCellier, Aux-les-Bains No.828401 Year of construction1978 Main Features MaterialStainless steel Volume1000 Ltr. Motor2.2 KW Specified Features - Stirring vessel MaterialStainless steel 1.4401 (316) Open stirring vessel(1x) Capacity1000 Ltr, Cover is missing Vessel sizesdia. 980x1400mm, Vessel insulated Outlet± dia. 20mm With jacket(120 Ltr) Information Floorspace1,2x1,2 M Total height1,9 M Weight800 KG Extra Specifications- With bottom driven magnetic stirrer (motor ± 2,2 KW) Stirring vesselsCellier FranceStirring vessels > Stirring vesselsBrand > Cellier France What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many ...

Item Condition: Signs of Use Availability: as of now Disassembly: by buyer Location: Soest Ceiling Air Cooler: GEA - DEA 081D Power ratings: 230 V, 50/60 Hz Internal dimensions approx.: W 2400 x H 2400 x L 3296 Price: 1450 € VB System: in operation Location: near Soest

Blow-through lock, supply, cell lock, cell wheel lock, cell wheel lock, dosing lock used AZO Ltd. Type: Z100/2P Inlet approx.: 250 mm Height approx. 450 mm Cell wheel approx. 320 mm Cell wheel width approx. 250 mm approx. 8 cells Hole circle flange approx. 335 mm with suction filter Geared motor with variable speed LENZE 11.342.13.12 0.5 kW 3.3 to 50 rpm 220/380 V Total dimensions approx.: 1500 x 600 x 450 mm The lock was used in the food industry. Probably for transport and dosage of sugar. Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

CTS climate test cell Walk-in test facility Here we offer you a CTS climate test cell. CTS climate test cell type TW -60/20 T means: Temperature W means: Walk in -60 means: lower temperature -60 °C 20 means: 20 m³ test room volume Plant description: With the temperature test cell, the function or material property of a test material can be tested under temperature influences. The system is divided into the test chamber including the machine compartment and a control station including a lock. The lock can be tempered independently of the control station or test chamber to minimize moisture input when entering the test chamber. The vertical air flow with a correspondingly high amount of recirculating air guarantees a good temperature transfer to the test material. The air treatment room is located at the back of the interior. To the left of the system, the units are located ...

Cell wheel lock made of noble steel unused KREISEL Environmental Technology Type: ADG 630 x 800 x 21-24 Z Built: 2005 Inlet opening: approx. 800 x 500 mm Outlet opening: approx. 800 x 500 mm Cell wheel diameter: 630 mm Number of cells: 12 Cell depth: approx. 200 mm Cell wheel made of stainless steel Housing made of steel Geared motor : SEW-EURODRIVE Type :RF107 AR132S/MWEX/II3GD DV132M4/TFII36D 7.5 kW 24 rpm 230/400 V IP65 Motor Ex protected! Total dimensions: approx. 2700 x 800 x 800 mm

Nova BioProfile Flex Automated Cell Culture Analyzer BioProfile is an automated cell culture analyzer that measures up to 15 important cell culture attributes. By combining up to five separate instruments into one easy-to-use instrument, BioProfile FLEX simplifies workflow and saves time, labor, and operating costs compared to multiple instruments. The FLEX automatic sampler takes samples from its two fermenters and transmits them to the measuring unit of the FLEX analyzer. The data obtained from the FLEX autosampler were compared with data taken manually from the reactor and their statistical analysis was performed. Specifications Sample analysis time: 2.5 minutes (gases only – PO 2 + PCO 2 ), 4.0 minutes (Chemistry/Gas and Osmolality), 6.25 minutes (all 15 tests), Operating temperature range: 15-30 °C (59-86 °F), Relative operating temperature Humidity range: 20-85 ...

Cell with TIG-OTC-NH52-NEFC welding robot Country of origin of the cell: Italy Year of production of the cell: 2017 Country of origin of the robot: Japan Brand: OTC NH5 Year of manufacture: 2016 Number of axes: 6 Reach: 866 mm Load capacity: 5 kg Control: OTC FD 11 Source: OTC DA 300-P Cell dimensions: Length 3500 mm 1900 Width mm Height 2400 mm

ABB IRB 2400 M2000 robotic machining cell manufactured in 2004 in Switzerland, is equipped with an ABB IRB 2400/16 6-axis industrial robot and an ABB IRC5 controller for the control of the manipulator and peripherals. The machining station has so far been configured and used for milling of allowances after thermoforming workpieces. The high-performance milling robot has an arm with a maximum reach of 1550 mm, capable of handling workpieces weighing up to 16 kg. The industrial robot achieves the best cycle performance thanks to modern technology that automatically optimises parameters and executes the programmed path regardless of speed or operating mode, even after an emergency stop or power failure. The BaseWare OS operating system is used to fully control every aspect of the machine, ensuring the highest machining accuracy is achieved. The robotic milling station is offered with  ...

Cell Berger with grinding robot Kuka KR 180 (external grinding A1) Grinding cell Berger 2012 (external grinding A1) - Total weight approx. 6300 kg - Dimensions of the cell: approx. 4650 x 2400 x 3100 mm 6-axis robot Kuka KR 180 R2500 Extra - Year of construction 2011 - Control KRC 4 - additional axis (7th axis) Belt grinding station BSS10 belt dimensions 3500 x 30 mm - contact disc diameter 200 mm - Motor power 4 kW 2 x polishing stations, - Polishing disc diameter 350 - 600 mm - Power 5.5 kW Gripper change cabinet Belt conveyorsInteroll Automation GmbH - Total length approx. 2000 mm - Bandwidth approx. 440 mm

Cell Berger with SChleif robot Kuka KR 180 (internal grinding I1) Grinding cell Berger 2012 (internal grinding I1) - Total weight approx. 6200 kg - Dimensions of the cell: approx. 4650 x 2400 x 2900 mm 6-axis robot Kuka KR 180 R2500 Extra - Year of construction 2011 - Control KRC 4 - additional axis (7th axis) 2 x Polishing stations, Polishing disc diameter 350 - 600 mm Polishing disc width 100 mm - Power 5.5 kW

Miniature measuring cell, measuring cell MARPOSS A11 3408360513 15XH0129 approx. 1.5 m Connection cable New ! Dimensions ( measuring cell without cable ): 82 x 14 x 12 mm Dimensions ( packaging ): 155 x 100 x 30 mm

Miniature measuring cell, measuring cell MARPOSS A124 C3419886154 approx. 3.0 m Connection cable New ! Dimensions ( measuring cell without cable ): 32 x 7 x 14 mm Dimensions ( packaging ): 120 x 100 x 30 mm

Miniature measuring cell, measuring cell MARPOSS A11 HBT B3470017713 approx. 1.4 m Connection cable New ! Dimensions ( measuring cell without cable ): 82 x 14 x 12 mm Dimensions (packaging): 145 x 85 x 60 mm

Modular cell culture station in hypoxia Biospherix X2-072514-1-00 1. Isolated workstation for cell culture work under controlled conditions. 2. Multiple incubation chambers, with independent O2/CO2/RH programming. Various sizes and configurations. 3. The incubation sub-chambers have doors that open into a large glove handling area with an aseptic and temperature, O2 and CO2 controlled environment. 4. O2 control from 0.1% to 99.9% is possible in each incubator. 5. Low humidity interior atmosphere in the crop handling chamber that reduces the risk of contamination. 6. Heated interior atmosphere and work surface. 7. Chambers for housing equipment (microscopes, bioreactors, centrifuges, pipetting stations, refrigerators, lyophilizers, cell sorters, robots, FACS, etc.) also with controlled atmospheres. 8. Control of the O2 level also in the SAS or input/output exchange airlock for ...

Welding cell ICS Robotics with 2 robots Panasonic G2 Robot: 2 x Panasonic G2 6-axis Year of construction: 2011 Source: 2 x Panasonic WG-EG1400 Dimensions from the cell: 4500 mm x 3000 mm x 2600 mm Indexer: Panasonic 3000 mm

Load cell, tensile and compressive force sensor, force transducer, load cell PAGUS 3091.100.106.00 Measuring range: 5 kN Nominal signal: 10 V Dimensions: 80 x 70 x 50 mm

Load cell with connection unit, force transducer, load cell PROMESS 20002 10900/4 Measuring range: 1 kN Cable length approx. 0.6 m used, tested ! Dimensions (sensor): 40 x 40 x 32 mm Dimensions (connection unit): 160 x 95 x 42 mm

Robot cell for leak testing consisting of: Robot FANUC LR Mate 200iC/5L – 2008, Table for measurements, equipped with 8 light curtains, 2 Innomatec devices for leak testing, type LTC – 502. The cell has a safety system and CE

Robotic industrial cell with BLM Dynamo-E tube bending machine Industrial cell consisting of: automatic bar feeder BLM CRMA7, Industrial robot Fanuc M16IB20, Tube bending machine BLM Dynamo-E year of manufacture 2007, machine number 200016, 2 handle conveyors, with photoelectric control, Resistance welding machine, Constructione Italy, PPN83, machine number QM328001, 2 resistance welders, Constructione Italy PPN83, Donation tape. The whole is fenced with networks controlled by Siemens with CE certification Link to the video – https://youtu.be/y5yYJQhkrRw

Industrial Robot Reis Robot Cell with Traversing Axis Manufacturer: Reis Type: RV40 Year of construction: 2004 Cell consisting of: Robot Rice RV40 Tilt&Turn module RDK05 (500 kg) Traversing axis RLV25 Incl. spare parts package Without laser optics !

Radio system, antenna contact module, wireless RF modem, pico cell antenna -Manufacturer: CP Technologies, Pico Cell Antenna 2.4 GHz orig -Type: WAN-2185 -Number: 2x antenna available -Price per piece -Dimensions cardboard: 280/240/H85 mm -Weight: 0.7 kg

Load cell, double bending beam load cell -Nominal load: 100 kg -Accuracy class: C3 -Cable length: 3 m -Material: stainless steel -Protection class: IP 68 -Dimensions: 39/120 mm -Own weight: 0.4 kg

Used freezer cell KOMA, type: - Large freezer cell for 55 to 60 rack trolleys - down to -25°C - Cooling capacity: 25.1 kW - Condition: very good - Location: Germany Viewing possible on request.

Muratec, Murata Machinery Vectrum 3046 + Cell loader F1-1250 loading & unloading system with Cell loader F1-1250 Year of manufacturing 1998 Ask for video please- Punching power 30tons 2. Sheet material thickness up to 3,0 mm in maximum sheet size of 2500x1250mm (With hand loading 6,0mm thicness sheet) 3. The machine is made in 1998 4. „Power on (Time) 17200 hours. 5. Softwear for CNC & nest Lantek cam 6. Marathon & 114 type tooling system. Lot of tools. (If necessary, can provide a list.) 7. The turret layout as an attachment.

New machine in its original box - price offered 30% off. Description : https://www.sonybiotechnology/us/instruments/fx500-exchangeable-fluidi cs-cell-sorter/specifications/ The FX500 is a microfluidics chip based cell sorter. Its fully replaceable fluidics system lets researchers easily replace the entire fluidics path to control sample-to-sample carryover. The FX500 features comprehensive fluidics controls, advanced automation and easy to use software. Patented CoreFinder™ technology automates instrument setup and streamlines workflow. The optical design offers up to three collinear excitation lasers - 488 nm, 561 nm, and 638 nm and six fluorescence detectors. The six free-form PMTs enable detection of fluorescence signals from any laser-based on filter setting. The FX500 is for non-clinical research use only and is a Class 1 laser product.

Cell with robot KAWASAKI RS005L A + band saw Year of construction / robot: 2010 Control: CNC 6-axis Max arm range: 903 mm Max load capacity: 5 kg Country of origin: Japan

Cell sluice,light metal,gearmotor and chain drive,0,18 kW,Ø7"

Robot milling cell Manufacturer: AMI consisting of the following components Industrial robot Kuka type KR180 R2500 extra Year of construction 2019 Operating hours: 100 Control: KRC4 Milling robot system 12 kW for KRC4 ES779 milling spindle Recooling system Socket for robots 2 x Kuka positioner KP 2 HV2600 HW with base plates 6-fold tool tray Enclosure for 2 separate work rooms

Compact cell Fanuc ArcMate 100/7L with R30iB control, Lorch S3 pulse welder new Number of axles: 6 payload: 7Kg working range: approx. 1633 mm Year of construction: 2016 Table area each 750x500mm Overall dimensions: approx.:2500x1500x2200 Total weight: approx. 2000kg Net amount plus 19% VAT

ABB Robotics IRB 1400 compact welding cell with manual rotary table and Fronius TPS 4000 welding machine Overall dimensions: approx. 4000x2350mm Robot: ABB Robotics IRB 1400 Control: S4-M98A Max. working radius: approx. 1450mm Load capacity: 5kg Year of construction: 1998

Cell with an industrial robot BJB Motoman YR-HP20-A00 6 axes maximum load: 20 kg Reach: 1717 mm Year of construction: 2008

Z-filter cell, fine dust filter for duct installation, filter cassette, fine filter HTT ENERGY GmbH KL Type G4 Filter class EN779: G4 Size: 600 x 276 x 48 mm Nominal flow rate: 1700 m3/h Final pressure loss: 50 Pa ( 0,0,5 mbar ) Material: Frame: Stainless steel ( 1.4301 ) Temperature resistance: up to 70 °C New ! Dimensions ( filter ): 600 x 276 x 48 mm Dimensions ( packaging ): 610 x 290 x 55 mm

Load Cell SIEMENS SIWAREX R 7MH3105-3BB0 K-60t-R1 Measuring range: 60 t approx. 10 m connection cable ! New ! Dimensions (packaging): 115 x 105 x 100 mm

Ionizer cell, electrostatic filter LTA 465 x 440 x 80 1371947 11 - 12 kV Frame: Aluminium New ! Dimensions: 465 x 440 x 90

Kistler Piezoelectric Force Force Load Cell 9323AA incl. Calibration Certificate Item Condition: New as pictured Specifications: 1-component force measuring element Fz: 0 ... 100 N to 0 ... 10 kN - Sensitivity: -10 pC/N - Dimensions DxH (mm): 20x26 - Female thread: M5x0.5 - Connection: KIAG 10-32 neg. H1R6A16K23_EK 0.2 kg. You can find more force gauges - new and used - in our shop! International shipping costs on request!

Conveyor Belt, Belt Conveyor Belt, Conveyor Belt, Belt Conveyor, Chain Conveyor, Pallet Conveyor Belt, Pallet Conveyor -Drive: geared motor SEW-Eurodrive with brake 0.55 kW/15 m/min -Weigh cell: Bizerba HLC-C3 -Chain track width: 750 mm -Dimensions: 1995/990/H480 mm -Weight: 334 kg

Shear beam load cell -Nominal load: 500 kg -Nominal value tolerance: %+/- 0.1 -Stainless steel: 1.4548 -Protection class: IP 68 -calibratable -Dimensions: 32/32/130 mm -Net weight: 0.98 kg

Cell analyser with proven reliability. Building on more than 25 years of BD experience and leadership in flow cytometry and multicolour analysis, the BD FACSCanto™ II system is an easy-to-use benchtop analyser that delivers proven performance, accuracy and high-quality results. The BD FACSCanto II offers the ultimate in flexibility and can be configured with two or three lasers to detect up to 6 colours. Date of purchase: 2010 The instrument includes : -1 BD Canto II flow cytometer ( Excitation source: blue (488-nm, air-cooled, 20-mW solid state) & red (633-nm, 17-mW HeNe). A third violet laser (405-nm, 30-mW solid-state) can be added at additional cost. ) -1 HTS module with 4 sets of 40-tube carousels (12x75 mm) -1 fluid cart -1 monitor -1 CPU + keyboard + mouse -1 BD DIVA software licence key (manuals and software installation CD supplied) Details of specifications and ...

WE OFFER AN NICE CONDITION TWIN ROBOTI WELDING CELL YEAR 2012, MACHINE WAS USED IN PRODUCTION FROM 2012 TO 2019 MACHINE WE CAN PUT FOR CUSTOMER ON GROUND, START UP AND MADE AN OPERATORS TRAINING POSITIONER IS HORIZONTAL TURNING: SEE VIDEO LENGHT OF POSITIONER: 4 METERS MAX LOAD PER SIDE PALET 750KG ROBOTS 2X OTC MODEL: NV61-NEFN ROBOTS CONTROL: AX-21 CV0000 WELDING MACHINES 2X FRONIUS CMT TOOLINGS PALET CAN BE CHANGING WE CAN OFFER ALSO TOLINGS FOR THE CUSTOMER PRODUCT :

Cylinder sensor with GMR cell, 2 pcs IFM ELECTRONIC MK5308 MKC3028BANKG/G/0.3M/ZH/AS 10 - 30 V DC connector Connector: M8 x 1, 3-pin Material: Housing: PA; Mounting eccentric: stainless steel cable: 0.3 m, PUR New ! dimensions (sensor without cable): 26 x 6 x 3 mm dimensions ( packaging ): 200 x 150 x 10 mm

Description: Lot consisting of No. 7 cell phones and No. 1 tablet, various manufacturers including NOKIA, HUAWEI, APPLE, LG, SAMSUNG, SONY and ASUS tablet. Approx. Onsite Dimension. (l x w x h): 200 x 200 x 200 mm, weight approx.: 1 kg

Description: Welding cell unit composed as: Robot KUKA , Type: KR30L6-2 Article Number: 10022094 Serial  ,Number: 709150 YOM: 2017 weight: 700 kg , Load capacity: 16kg Working Range : 3102 mm Controller and pendant KUKA Model: KR C4 Serial Number: 331261 Rotating table VP3-V2H500 , Serial Nubmer: 152219 YOM: 2017 FRONIUS TPS welding machine Serial Number: 28185846 YOM: 2017 Power: 1.4kw Security fences Approx. Onsite Dimension. (l x w x h): 4,000 x 2,400 x 2,520 mm, weight approx.: 6,000 kg

Fabr. BABCOCK, type: 500 NVD, electric drive 3 KW, inlet diameter = wheel diameter: 600 mm, height 500 mm, 13 pieces available, for extracting fine dusts