burner used for sale

Thermal oil stove with TOUCH controls for rack trolleys 60/80cm, with integrated boiler system type WTO 110 HFT with gas burner with expansion and drain vessel incl. 4 trolleys

Pressure washer, hot water pressure washer -Manufacturer: Kärcher, hot water high-pressure cleaner type 855 H -Connection: 230 volts -Power: 1.8 kW -Flow rate: 6.7 l/min 100 bar / max. 110 bar, 80°C -Burner: max. 25 kW -Dimensions: 630/380/H890 mm -Weight: 47 kg

Overview  The steam generator was built in 2015 by the American manufacturer Clayton. The machine was recently dismantled by a specialist company. Technical specifications  Net output: 589 kW Equivalent steam production max.: 790 kg/h  Water content in operation: 130 liters  Regulated gas pressure minimum: 25 mbarG Maximum gas pressure: 200 mbarG Consumption at full load: 62.9 Nm³/ h  Burner regulation (2-stage): 0-50-100 %  Steam quality: > 99.5  Combustion efficiency (100% stage): 92%  Combustion efficiency (50% stage): 94  Generator dimensions (LxWxH): 2,030 x 1,300 x 1,835/ 2,200 mm  Dry weight: 1,215/ 1,285 kg  Pump dimensions (LxWxH): 1,350 x 680 x 1,025 mm Weight of water pump: 325 kg  Installed electrical power: 4kW Accessories  Back pressure regulator DN40  Vertical atmospheric deaerator + chemical dosing pump  Water softener  Chemical tank 60L + alarm + drip t ...

Available two units of this SIAT RECOPACK recovery boiler. This boiler recovers the heat from the exhaust gases of turbines or engines, but it doesn't have burner to produce his own heat. They are disassembled and ready to be load. Power 493kW pressure 12 bar Capacity 5065 l YOM 2009 Model Recopack

Thermal oil boiler Heuft HK230 - Thermal oil boiler - Manufacturer : Heuft / OHL Apparatebau & Verfahrenstechnik GmbH - Type: HK 230 - Thermal oil boiler with gas burner - Heating capacity : 230 kW -Ab. Operating pressure. 4 bar -Ab. Operating temperature:300 C - Capacity: 118 L - Minimum flow rate: 9.5 - Operating voltage: 400 volts 50 Hz - Control voltage: 230 volts - Connected load: 11.6 kW - Nominal current 22.5 A - Year of construction: 1998

From insolvency: ESS Synmag 4000 Year of construction 2007 with feed case DVK 5000 with 5meter intermediate package 4 Roller drive Water cooling 2/4 stroke Welding range 40-400Ampere Duty cycle at 100% 240Ampere at 60% 300Ampere with 4meter burner, ground cable --without pressure reducer--

The rapid steam generator is installed in a 20 ́High Qube container including a Weißhaupt Monarch heating oil burner, economizer, stainless steel feed water tank, water treatment, blowdown vessel, chimney, etc, Power: 1,118 kW, Perm. Operating pressure: 12 bar, All documentation and test book are available., The return to service and the associated acceptance and repairs are the responsibility of the buyer; the container is sold without any guarantee or return claims; this is taken into account in the offer price.

From operating resolution: MIgatronic PI 250 DC Year of construction 2014 Pulse function HF Ignition Water cooling without function Welding Range: 5-250Amp 250Amps at 30% ED 180A at 60% 150A at 100% 220 volts with 8meter burner (sheathing partially damaged), ground cable and pressure reducer Dimensions in mm approx. 1100x630x720 --Very neat device-

From operating resolution: ESS Squarearc 356 C Year of construction 2011 AC/DC Welding range 5-350 amps Pulse function HF Ignition Water cooling 350Amps at 60% ED complete, with 6meter burner, ground cable and pressure reducer Dimensions in mm approx. 980x450x930 --Very neat device-

It is a used, reconditioned WP rack oven REC 1280 (BJ 2018) for sale. - for 1m trays - great condition - Weishaupt natural gas burner - Variopilot - Thermogate - incl. 3 x rack trolleys Price on request.

From the stock of authorities: Pulse system little used Elmatech Hybrid 4002 Year of construction 2005 Welding capacity 400Ampere at 60% ED 320Amps at 100% Water cooling 4-Roll Wire Feeder Wire feeder case DV 39 with 5meter intermediate hose package 4meter burner with regulator Wire rolls 1.0-1.2mm + rolls for aluminum wire Dimensions in mm without case 1000x450x930 with operating instructions, pressure reducer and ground cable

From operating resolution: Selco Genesis 352 GSM DC Device No.007410000118 with water cooling Welding range 6-350 amps 350Amps at 60%ED 270Amps at 100% ED 380 volts with 8meter burner AQ 18F with flexible head and ground cable Adjustable pulse function RF Ignition 2/4 stroke

From operating resolution: Pulse welding system Cebora EVO Speed Star 380 TC Specifications: Control Sound Digibox MIG P4 Welding range 10-380 amps 310Amps at 100% ED 4 Roller feed Water cooling TIG welding possible in the DC range Feed rollers 1.2mm Burner 4meter with 1.0mm wire, ground cable and pressure reducers-- Dimensions in mm approx. 950x850x1020 Operating instructions

From insolvency: Rehm Tiger 182 DC High Year of construction November 2020 220 volts DC Welding range 4-180Ampere Power: 180A at 40% ED--160A at 60%ED--140A at 100A ED J0iqq3 2/4 time RF Ignition Pulses 4meter burner, with ground cable and pressure reducer

Probatone 5 Typ2 SMH2 PC Manufactured in 2019 Pristine condition - less than 5000 kg roasted Premix burner that can run either propane or natural gas 3 phases 380/400V supply Airflow separated (roasting & cooling with no interference) Additional air temperature thermocouple Variable frequency drive for the airflow and the drum rotation speed Computer connection (Possible to create recipes and reproduce them with Artisan/Cropster) Sold only in the EU Available in June 2024 Find our other announcements by clicking on the machine list in the dealer profile

Chaudiere Socother steam boiler, type: STT 350, fabrication number: 43470, year of construction: 1987, 410 kW, working pressure: max 49 kPa, test pressure: 300 kPa, steam production: 560 Kg/h with Weishaupt burner, model: WG40N/1-A ZM-LN, serial number: 591230009, 230 V, 1 Ph, 50 Hz, 0.94/0.85 kW, gas heated, unit build in container, dimensions container: 2400 mm x 3300 mm x 2600/3000 mm.

Key data: 700 °C, 2400 mm, 6500 mm

For sale is: 1 piece gas-fired chamber furnace with air circulation and bogie hearth Manufacturer: Nolzen Industrieofenbau GmbH & Co. KG Type: KLWg 220/180/650 Year: 2017 for unsupervised operation for three-phase three-phase 400Volt For temperatures up to max. 700 degrees C. for natural gas "H", liquefied petroleum gas Number of burners: 8 Total burner power: 720kW For more technical data, see the attached PDF. The furnace itself was only in operation for 4 years and during this time it made about 100 annealings, each lasting 23 hours.

Description: Consisting of various burner inserts and soldering attachment With operating instructions In a case Approx. Onsite Dimension. (l x w x h): 430 x 230 x 100 mm, weight approx.: 8 kg

Description: Roasting plant: , year 2018, consisting of: , Roaster : IMA Petroncini TT 5-10 Speciality - weight : 300 kg approx - dimensions : 1550 x 900 x 1700 mm. , Equipped with: , Modulating burner 0 - 100% Classic or Avantgarde control Single-phase power supply Independent roasting and cooling fans 8 setpoints and 20 customisable roasting profiles Speed monitoring and saving roasting temperatures Cropster Ready , Remote assistance Batch size (kg) 3/10 , , Capacity , (kg/h) Up to 35 Roasting time (min) 10-20 Following: Batcher: Techno D M1 - weight : approx. 100 kg - dimensions : 900 x 650 x 2000 mm, with hopper and packing surface.  , Packer/labeller: Top Seal - weight : 50 Kg ca - dimensions : 400 x 500 x 1400 mm, with thermal sealer. , Ideal for creating artisanal blends to sell to bars or better yet for those who ha ...

Sand feeding/mixing/reactors (modernized in 2007): Control system: Siemens S7, number of machines: 23. 5x Jöst discharge chutes, sand screen, mixer, Eirich UE 62 discharge unit, bucket elevator, reactors, twin-shaft mixer, various weighing belts and conveyor belts. Press plant (modernized in 2012): Control system: Siemens S7, number of machines: 6. 2x Atlas presses incl. table removal and stacking device, scraper, empty trolley platform and Semet turntables, Atlas blank transfer table, 2 press tools in use and 22 additional tools available, various conveyor belts. Hardening shop/steam boiler (modernized in 2015): Control system: Siemens S7, number of machines: 13. Dapf boiler standard burner Saacke, 9x hardening boiler Scholz with automatic condensate drainage, water treatment Grünbeck, condensate collection tank, low-pressure feed water tank, approx. 130 hardening scales. Packaging sy ...

Power ratings: 400/230 V, 50 Hz, 3/N/PE Item Condition: Signs of Use Availability: as of now Disassembly: by buyer Heating Type: Gas Location: Soest Gas Burner: ELCO Function: in operation Price: €3,750.00 VB

Power ratings: 400/230 V, 50 Hz, 3/N/PE Item condition: well-maintained Availability: as of now Disassembly: by buyer Heating Type: Gas Location: Soest Gas Burner: ELCO Function: in operation Price: €4,100.00 VB

MAX. TEMP.: 1000 °C, CAPACITY: 60 TON, NO. OF BURNERS: 20,

Cutting cutter Kjellberg-Eberle - used Type: SII20 Machine No.: 1331 - 220 V, 50 Hz, 2.5 kVA, IP 31 - on 04.02.1990 a new control system (NS 3003) was installed by Etek - Built in 1974 - 4 burners - Table dimensions: 6m x 2.50m - Total area: 6m x 5.5m x 2.4m In good condition!

Gas-fired recirculation chamber furnace max. temperature: 300°C external dimensions ( d x w x h): 2500 x 5300 x 8300 mm internal dimensions ( d x w x h): 1500 x 3800 x 3000 mm control zones: 2 burners power: 4 x 90 kW fans power: 2 x 4 kW

Gas-heated bogie hearth drying oven (not for flammable paint) temperature max.: 420°C burners heating power:300 kW divided on 2 burners / zones circulation fans: 2 x 5,5 kW = 11 kW el. total connected load: approx. 15 kVA control zones: 2 PLC: Siemens S7 approx. external dimensions (w x h x d): 4700 x 4200 x 6000 mm length with extended bogie hearth: 11.000 mm internal dimensions (without bogie hearth) width: 4000 mm hight: 2900 mm (2500 mm usable with bogie hearth) lenght: 4000 mm max. charging weight:20.000 kg net

Magra-oil distributor Manufacturer: Magra Type: oil distributor / patch distribution Function: A safe switching distribution when several tanks and burners. Threaded ball valve with mechanical tank locking as a combined suction and return distribution. In very good condition!

Qty. 1 Second-hand extrusion press line Mfc.: 3TC, Allen Bradley, Rexroth, Gautschi, Elhaus, Nederman, Hydrotec, Marx GmbH, Truninger, Ekatech Force: 3500 MT Built: in 1960’s Pressure: 315 bar Billet dia.: 343 mm x 900 mm (can be modified 14 x 1.0 m) Modernisation: 2011 Complete exchange of control system on press to Allen Bradley Control Logix including encoders for Ram, Container and Shear. Change of pump controls to Bosch Rexroth HS4. 2012 Complete change of hydraulic system (excluding pumps). New side cylinders and container cylinders. Safety rebuild of press and with change of PLC to Allen Bradley Control Guard Logix L72S (which is the current CPU). Change of control system of billet furnace. Complete new electrical system and integration of logic into the press PLC. Modernisation of gas burners in the furnace. 2013 Change of one of the main pumps to Bosch Rexrot ...

Cortina DS 3100, working range: 8,000 x 2,000 mm, year of construction Dec. 2004 CNC-controlled cutting machine with robust bridge suspension, form-fitting longitudinal drives and precisely machined guide profiles, Connection voltage: 400 V 50 Hz, TN-S mains (A/PE/N) track width: 3100 mm working width: 2000 mm dead length: 1500 mm Total width: 3525 mm Operating side: left power supply: right fuel gas: propane incl.: OmniCom Explorer C drive 15 m/min DC dual-sided Longitudinal drive on rail feet machine cutting torch ALFA (with internal ignition) OmniFlow automotive supply (gas quantity control up to 6 burners) OmniFlow Control torch suspension OmniLift 200 SensoMat ALFA SensoMat ARC/SR Plasma SetControl, tactile first height detection interlock for a maximum of 2 systems HT 4400 HySpeed fine beam plasma cutting system cutting up to 50mm energy supply via energy chain (autogen/plasma) cu ...

Used deck baking oven MIWE, type: Ideal 1800.5 FO - In the bakery State baking surface: 18 m² Number of spots: 6 pieces Hearth size: 1,800 x 1,600 mm -With gas - oil burners according to customer requirements - manual control - fully assembled - State: well the stove is technically and visually in good condition and is ready for use immediately. Delivery and installation available on request. We like to overtake even the oven for you.

Manufacturer: Solar Turbines INC, San Diego USA Model: Taurus 60 with Solonox combustion, Packager: Turbomach Version: T 7301 Yoc package: 1998 Turbine engine: new engine installed in 2012, only few hours since installation Condition: fully serviced and ready for start. Capacity: 5200 kW Speed: 14.944 U/min continual Fuel: Natural Gas and Light Diesel (dual fuel) Fuel consumption: 122.469 kJ/kWh Burners: 12 Start system: electro.hydraulic, 90 kW Outlet temperature: 486°C Exhaust gas: 21.244 kg/s

Double chamber furnace, make VEI-Engineering type: KA_GB 10.14.14/d max. temperature: 550°C fan power: 2 x 4 kW heating: natural gas burners power: 2 x 100 kW useable dimensions per chamber width: 1.000 mm height: 1.400 mm depth: 1.400 mm

Biomass Plant, 5 MWel, 50 Hz, yoc 2002, in operation Boiler • Technical data: - Fuel tank capacity: approx. 1 .300 m 3 - Exhaust gas volume 29,000 Nm3/h - Average combustion temperature of 900°C (850 for 2 s.) - Thermal power of the furnace 13 MW - 2 add. Burners 5 MW each - Average calorific value Hu 12,500 kJ/kg - Throughput capacity 3,991 kg/h - Boiler working pressure 41 bar - Superheated steam temperature 420°C - designed amount of steam 14 t/h - Fuels: RDF, wood chips, straw, remains of chipboard, choiceed waste Hours of operation of the entire plant appr. 120,000 hours Steam turbine - TWIN steam turbine KKK, type: CFR 3 / AFA 6 GTA - Generator AvK, type DIG 140 k/4W - Gearbox Renk, type: ELCO W-shape can be inspected in operation this week, - SGS can be ordered for inspection.

Gas-heated stove Usable dimensions (stove wagon): Depth: 4,000 mm Width: 3,500 mm Height: 1,500 mm Temperature max. 1200 C Working temperature: 980 C Heating capacity: 810 kW divided into 6 burners of 135 kW Drives stove wagon: 2 x 0.75 kW Number of rule groups: 3 Control: Siemens S7 Please note that we use the ovens according to customer requirements (e.g. dimensions, temperature, type of heating).

CNC Portal Plasma Cutting Machine + Autogen Manufacturer: Messer Type: Omnimat L 5600 Built: 1999 CNC control: Omnicom Track width: 5,600 mm Career length: 25 m Working range: 4 x 22 m 1 plasma torch with hypertherm HD3070 power source 2 car-gene burners 1 powder marker Suction table Filter system Donaldson

Gas-fired preheating furnace, make VEI type: VEI_KO_V_GB_400-350 temperature: 350°C burners power: 2 x 200 kW fans: 2 x 4 kW useable dimensions x 2 (h x d x w): 1.000 x 1.400 x 2.800 mm

Qty. 1 Second-hand batch-type annealing furnace Mfc.: LOI SAAR Type: natural gas (Hu=3.6 MJ/Nm³) Charging material: square, round dia. 50 up to 200 mm Length: 6.2 m Max. heat treatment temperature: 950 °C Capacity: max. 60 T at normalising 35 T Application: Tempering, stress relieve, normalising Heat gradients: 60 °C/h average (adjustable) Heating zones: 4 Number of burners: 20 Control principle: on/off with digital programmer Temperature precision: 10°C tolerance at 550 °C

Used multi-story continuous furnace W&P, type: Megador - 7 floors - Top and lower heat can be controlled independently of each other - Net band - Swarming - Touchscreen - WITHOUT boilers, burners and loading - Baking area 120 m2 The oven is out of service. Visit and test run are possible at short notice by arrangement.

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

Unit set for paint booth with speed control and heat recovery: Make : Wolf, Type 4/B-M Year of construction 2009 Dimensions : 1.5 m x 4.2 m x 3.0 m (approx. WxLxH) Heating unit : 209 kW Burners : oil burners, Weishaupt brand, alternatively gas burners Exhaust gas fireplace : stainless steel, single-walled, diameter 250 mm length approx. 6 m Supply air unit : 21,200 m3/h; 7.5 kW, 1,500 1/min Exhaust air unit : 21,000 m3/h; 7.5 kW, 1,500 1/min Energy saving : Speed control with frequency converter and heat recovery Pipelines : Supply and exhaust air pipes, deflector hood, air intake hood Electrics : Control cabinet Location : Nuremberg Area Retail price : € 11.900,-, net, ex location

Paint booth Wolf-Taifuno: Make : Wolf, Type 4/B, Taifuno Year of manuf.: Cabin 2011, Aggregate 2009 Dimensions : 4.0 m x 7.0 m x 2.9 m (approx. WxLxH), total height 3.7 m Supply air blanket : Filter ceiling Lamps : 2 x 4 pc recessed luminaires with 4 x 58 W each Entrance side : 2-leaf gate 2.4 m x 2.8 m (approx. WxH), glazed Escape door : 0.65 m x 2.8 m (approx. WxH) Rusting : Full surface rusting 5x15 pcs. 790x495 mm, support bar 790x40x3 mm Heating unit : 209 kW Energy saving : Speed control with frequency converter and heat recovery Dry temperature : 80 degrees C Oil burners : Weishaupt brand, alternatively gas burners Exhaust gas fireplace : stainless steel, single-walled, diameter 250 mm length approx. 6 m Supply air unit : 21,200 m3/h; 7.5 kW, 1500 1/min Exhaust air unit : 21,000 m3/h; 7.5 kW, 1,500 1/min Pipelines : Supply and exhaust air pipes, deflecto ...

Paint booth: Make : Wolf Year of manuf.: Cabin 2011, Aggregate 1993 Dimensions : 4.0 m x 7.0 m x 2.9 m (approx. WxLxH), total height 3.7 m Supply air blanket : Filter ceiling Lamps : 2 x 4 pcs recessed luminaires with 3 x 58 W each Entrance side : 2-leaf gate 2.4 m x 2.8 m (approx. WxH), glazed Escape door : 0.65 m x 2.8 m (approx. WxH) Rusting : Full surface rusting 5x15 pcs. 790x495 mm, support bar 790x50x3 mm Heating unit : 267 kW Oil burners : ELCO brand, alternatively gas burners Dry temperature: 80 degrees C Exhaust gas fireplace : stainless steel, single-walled, diameter 250 mm length approx. 6 m Supply air unit : 22,800 m3/h; 7.5 kW, 960 1/min Exhaust air unit : 22,500 m3/h; 7.5 kW, 960 1/min Pipelines : Supply and exhaust air pipes, deflector hood, air intake curve Electrics : Control cabinet The paint booth was originally a Wolf drying booth, but wi ...

Plasma-gas cutting machine ECKERT JANTAR 2 was produced in 2007. Technical parameters: – CNC control: ECS 859 – table: 9 sections, 1.62 m long each – table width: 3.2 m – table length: 14.58 m – number of slides: 3 – possibility of communication with a computer – possibility of plasma and gas cutting – 2 Harris gas burners – plasma cutting thickness: 8-10 mm – gas cutting thickness: up to 90 mm – power supply: 230 V – rated current: 12 A – plasma aggregate: PA-S45W

Many thanks for your interest on our second hand machines, please find follow our offer: Like New Condition - fully rebuild in 2016 after never used manufacturer: Probat Type: GP 25 batch roaster output capacity: ca 25 kg/charge different: batch size approx. 25 kg Raw Coffee complete new electric (all control, drives and wires) Cube top of Roaster was redesigned. All electrical parts are NEW. Likewise, all gas components - safety valve, automatic ignition etc .. Sanding, new painting and chromming. New bearings screws etc.. Digital temperature meters and refurbished gas burners and all gas nozels, New motor. Power supply- 3x400Vac. Full Documentation exist for all - electricity and Gas safety. The machine was baught from the last owner in fully rebuild condition 2016 but never used. Is stored in the origin packaging from 2016! We offer this machine in 'as is' condit ...

type: gas-fired rotary hearth furnace with central recuperator and air preheating max. temperature: 1300°C max. furnace output: approx. 700 kg/h clear door opening (w x h): 600 x 400 mm number of burners: 6 number of control areas: 3 heating capacity: 720 kW el. total connected load: approx. 15 kVA PLC: Siemens S7

GE LM2500+ For Sale (31.3 MW, 50 Hz): GE LM2500+ natural gas-fired and associated Aalborg HRSG. The GE LM2500+ has a nominal output of 30 MW. The OCGT originally produced steam for local combined heat and power (CHP”) demand, which no longer exists. Due to this, the HRSG is kept in dry preservation and the OCGT operates using the bypass stack, providing black start and short-term operating reserve capability. Open cycle GE LM2500+ GT driving a 36 MVA generator, which is a totally enclosed air-cooled (TEAC”) design rated at 11 kV. The boiler on this unit is currently in dry preservation. The LM2500+, a design based on the very successful heritage of the LM2500 gas turbine, rolled off the production line in December 1996. The LM2500+ was originally rated at 27.6 MW, for a nominal 37.5 percent thermal efficiency at ISO, no losses and 50 Hz. Since that time, its rating has continually  ...

Qty. 1 Second-hand billet homogenising furnace – still on foundation Mfc.: Pieco Servis Sp.zo.o. Built: 2004 Billet sizes: 7” & 8” x 7000 mm Material: Al alloys series 6060, 6063, 6061 Type of furnace: continuous furnace with a mechanical hearth Ingot size: Aluminum billets Ø 203 and 178; ingot length L = 7000 mm Type of heat treatment: Homegenising process Installed power: Heating: 955 kW Electrial: 50 kW Type of built-in burners: ThermJet Supply voltage: 400 V, 50 Hz Type of heating gas: GZ50 Gas pressure: 150 mbar Furnace performance: 1700 kg/hour 1000 Mg / 25 days (three-shift operation) Unit gas consumption: 27 m³/ Mg Furnace operating temp.: up to 600 °C

Gas stove with electric ovenMKN type 2163403-02 with 4 burners, 2 large, 2 slightly smaller. Is used and functional. Oven inside Dimensions: W.: 53 cm, D.: 50 cmOutside dimensions W.: 80 cm, D.: 70 cm, H.: 88 cm

CNC Portal Plasma Cutting Machine Manufacturer: Messer Type: Omnimat L5000 Year of construction: 2000 CNC control: Fanuc Working area: 3000 x 6000 mm Extension possible 1 plasma torch with Hypertherm HT2000 power source 3 oxy-fuel burners without table without filter

Many thanks for your interest on our second hand machines, please find follow our offer: Like New Condition - fully rebuild in 2016 after never used manufacturer: Probat Type: GP 25 batch roaster output capacity: ca 25 kg/charge different: batch size approx. 25 kg Raw Coffee complete new electric (all control, drives and wires) Cube top of Roaster was redesigned. All electrical parts are NEW. Likewise, all gas components - safety valve, automatic ignition etc .. Sanding, new painting and chromming. New bearings screws etc.. Digital temperature meters and refurbished gas burners and all gas nozels, New motor. Power supply- 3x400Vac. Full Documentation exist for all - electricity and Gas safety. The machine was baught from the last owner in fully rebuild condition 2016 but never used. Is stored in the origin packaging from 2016! We offer this machine in 'as is' condit ...