127,435 used machines on RESALE, but how to find them? Machine Search
UNDERWATER PELLETIZER, up to 1.400 kg/h with soft and rigid PP max 30 MFI, Total installed power 67,14 kW, The supply includes:, Connection from your screen changer to the diverter valve, made of C45 steel heated by mica electric haters., Diverter valve heated with electric heaters This allows the flow of product to be diverted to the drain to bring the extruder up to speed, it consists of a C45 steel body with a specially perforated plate that diverts the flow to the outlet or die. This plate slides via a position-controlled hydraulic cylinder, operated by a hydraulic power unit complete with high-pressure hoses. Pressure and product temperature control probes are also included., Cutting unit consisting of: electrically heated die adapter/diverter valve; AISI304 granulation chamber; die with hard metal inserts, heated by electrical heaters; auger holder unit with blade pressure adjustme ...
UNDERWATER PELLETIZER, for rigid and soft PP max MFI : 30 (and more), electrical heater max 14,6 kW, n.2 thermo regulating zones, A pressure transducer and a melt temperature transducer are mounted on the purge valve. The purge valve is controlled by a hydraulic cylinder connected to a hydraulic power unit with a 2.2 kW motor., Steel die with brazed tungsten carbide plates. A conveyor cone for the molten polymer is installed inside., stainless steel granulation chamber, Impeller shaft with 11 kW 2-pole drive motor (3000 rpm nominal, 4000 rpm max) controlled by an inverter with rpm variation and speed readout on the panel. The shaft output side has special seals and a labyrinth and safety water drainage to protect the motor bearings. The impeller motor is integral with a slide sliding on rolling guides, operated, via a recirculating ball screw, by a manual handwheel equipped with a positi ...
Paint System for Engines(Year of Manufacture: 2019) Technical Data: - Footprint: approx. 26m x 9m - 118 skids - Average cycle time: 49 seconds - Process time: 97 minutes (approx. 1.5 hours) - Maximum capacity (3 shifts): approx. 258,000 units/year Main Components: - Loading and unloading area with continuous floor conveyor system - Automatic robot paint booth with dry separation system incl. recirculating air unit - Painting robot Series T2 with hollow wrist - High-performance automatic spray gun LZ-2013 - b+m cap cleaner APRA 12 for automatic spray guns - Manual paint booth with dry separation system - Exhaust systems for manual paint and adhesive spray guns - Fresh air unit - Flash-off zone incl. recirculating air unit - Chiller 1 – recirculating air temperature 40°C - Chiller 2 – recirculating air temperature 20°C - Dehumidifier - Reverse osmosis system and water softener - ...
Overview This palletizing and winding line consists of an Ocme palletizer and two Robopac Genesis stretch wrapping machines, both manufactured in 2014. The line was designed for handling shrink containers and is in good condition. It is suitable for palletizing and wrapping multiple pallet formats and offers a production output of 30,000 bottles per hour, depending on the format. The grouping of the layer formation is done by two Fanuc robots. There are two more Fanucs for the palletizing and the adding of an intermediate layer. The palletizing and winding is part of a complete line, from which some components have already been sold. Technical details Palletizer Manufacturer: Ocme Model: Pegasus F450 Year of construction: 2014 Products processed: Shrink packs: PET 0.75 L 2 x 32 PET 1.0 L 3 x 2 PET 1.5 L 3 x 2 PET 1.5 L 3 x 4 Pallet Formats: Euro Pallet 800 x 1200 Chep Duesseldorfer 6 ...
Manufacturer: HACO Model: PPM 30150 Year of Manufacture: 2007 Voltage: 380V 50Hz Capacity : 3000 x 150T Find more here - / Contact us at -
Key data: 40000 KG, 3600 mm, 4500 mm
242 pieces Frame P6 / Height 4,500mm / Depth 1100mm / Max. bay load 10,000 kg / Galvanized 880 pieces trusses PT150S / length 3600mm / 4000kg with equal distributor load, blue painted incl. locking pins
Senco PAL70 Compressed Air Nail Gun Top condition, MINT CONDITION, unused, is sold as used.
Qty. 1 Second-hand PET – CSD bottle filling line Mfc.: H+E Maschinenbau, MTA SpA, ABM, Posimat, Sacmi Filling, Bertolaso, JAKU/JB Michiels, KRONES AG, SMI SpA, Robopac SpA Built: 1992 - 2023 Capacity: 6,000 bph Products: CSD - PET Neck finish: PCO 1881 Format available: 0.5 L
Weinig Profimat 26 Super four-sided planer Working width 230mm Working height 130mm Number of spindles 5 Spindle system 7.5kw Down Left 11kw rights Mount 75kw Down 5.5kw Pneumatic clamps divided into 2 sections Feed speed adjustable by variator 5-24m/min CE Certificate Technical documentation Net price 68,000zł
Specifications Maximum pressure: 5.7 tons Pressing force: 1.18 kg/cm Bale size: 600x800 mm Bale weight: approx. 70 kg Power connection: 400V / 1.5 kW Year of Make: 2009 Productivity: approx. 3 bales/hour
Key data: 80000 KG, 3600 mm, 4500 mm
484 pieces Frame height 4,500mm / depth 1100mm / Max. bay load 10,000 kg / galvanized 1760 pieces trusses length 3600mm / 4000kg with equal distributor load, blue painted incl. locking pins Total 9600 pitches
Specifications Maximum pressure: 4 tons Press force: 1.14 kg/cm² Bale size: 700x500x600 mm Bale weight: approx. 60 kg Power connection: 230V / 1.1 kW Year of Make: 2012 Productivity: approx. 3 bales/hour Price: on request Machine is fully functional after technical supervision. If you have any questions, please call us: +48 696 072 985
Technical data of the pallet rack stand: Shelving system: Stow Type: Pal Rack NS The scope of delivery includes: 01x Pallet rack stand, used Material colour frame: Ral 5015 blue Material colour half-timbering: sendz. galvanized Frame profile: PLFB 30 Profile dimensions: P 120 x 92.5 x 2.5 mm Incl. cross and diagonal struts, Footplates The stands are pre-assembled ( bolted truss ) Height: 9,250 mm Depth: 1,100 mm Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.
A Dalex welding press/projection welding machine including Sortimat (ATS) feeding unit is available. Rated power at 50% duty cycle: 100kVA, max. welding power: 455kVA, open-circuit voltage: 8.88V, max. short-circuit current: 67kA, cooling water flow rate: 10l/min, electrode force min./max.: 120daN/720daN, single-stroke cylinder: 100mm, machine throat depth: 250mm, stop range: 148mm-400mm, belt diameter: 260mm. Weight: approx. 850kg, control system: MPS 200 multi R1. Including sorting and feeding unit, flow monitor, adjustment device and return stroke monitoring. Documentation available. An on-site inspection is possible.
2x Muller Martini Progress cross perforation cylinders: 1. One has gear 72 pitc 1/3” 2. One has gear 96 Pitc 1/4” Good condition, no damages. Available immediately.
Inv. Num. : 8766 Type: SPITFIRE 1500 Producer: Pierce Created: 2012 Parameters: Software: Lantek Expert Duct Work table length: 3000 mm Work table width: 1500 mm Maximum sheet thickness when cutting: 15 mm Plasma Source: HYPERTHERM 85A Machine height: 1400 mm Machine length: 3650 mm Machine width: 2520 mm Equipment: Exhaust fan
Pallet fork 2 t with Bobcat 90 cm holder, FEM2, tine carrier 102 cm
2.0 t capacity, 80x40x1200 mm tines, with Bobcat T30.60 & T35.105 telescopic handler mount
Hammer pile driver suitable for HM500 with 120 mm inner diameter, photos are only an example !
100 mm diameter pile driver suitable for Hammer HM100
NEW, FEM3A, 4.5 t load capacity, with 120 cm long tines, with Manitou attachment, 246 kg dead weight
NEW, - CROCODILE SHOVEL with 2 rear hyd. cylinders, - strong double stiffened hold-down, - 220 cm width, - 0.77 m³ capacity, - 410 kg dead weight, - with Euro mount, photos are only an example!
NEW Pallet fork 1200 x 120 x 50 mm FEM 2A 2.5 t load capacity Carrier width 1.20 m with Liebherr 506 attachment
BIG pallet fork with Bobcat 114cm attachment, NEW, - Pallet fork 1200x80x40 mm, - FEM 2A, - Capacity: 2000 kg, - Carrier width: 1.20 m, - mass: 159 kg, with Bobcat 114cm attachment
BIG pallet fork with Bobcat 114cm attachment, NEW, - Pallet fork 1200x80x40 mm, - FEM 2A, - Capacity: 2000 kg, - Carrier width: 1.20 m, - mass: 159 kg, with Bobcat 114cm attachment
NEW, pallet fork 200 cm wide, 4.5 t tines, 120 cm long tines, with Volvo BM mount
NEW: FEM3 holder, 3.5t pallet tines, beam width 120cm
180cm extension length, Suitable for tines up to max 130x50mm, ⬠230,- excl. VAT (per pair)
180cm extension length, Suitable for tines up to max 130x50mm, ⬠230,- excl. VAT (per pair)
180cm extension length, Suitable for tines up to max 130x50mm, ⬠230,- excl. VAT (per pair)
Pallet fork extension, 180cm extension length, Suitable for tines up to max 130x50mm, Price per pair excl. VAT.
Pallet fork 120cm, - with Manitou pick-up, - 3.5 tons
Key data: 130 mm
Installed capacity 498 kW, single degassing with vacuum pump, screw Optimized for film processing used for PE/PP. DC Drive Throughput with PE approx. 500-700 kg at approx. 150 kw. Throughput for PP approx. 450-550 kg at approx. 160 kw. Composed of: Foil silo with agitator and discharge screw approx. 5 m³ Regrind/granules, dosing screw, masterbatch, dosing screw, tamping unit. Extruder 130L/D 35 Hot Knock Off Granulator (Water Ring Granulator) Centrifuge Classifying sieve Removal with pressure blower Screw and barrel were renewed in 10/2020, (repair costs 45.000EUR) Groove bushing at the inlet renewed in 2015 is currently still at 60%. A new groove bushing is included as a spare part and is included in the retail price. (NP.ca. €5,000) The number of hours spent on the extruder from repair to dismantling of the system is 851 hours. Cooling system Industri ...
Mepac heavy duty vertical bagging machine for bulk productions.
Manufacturer: Tox Pressotechnik Model: MAG 075.222.A.001 Year of Manufacture: 2008 Condition : Excellent Min./Max. Air Pressure: 0.3 / 0.5 MPa ; 3 / 5 bar Max. Press Force at Max. Air Pressure: 680 kN Total Stroke: 100 mm Power Stroke: 11 mm Machine Weight (without tool): 3420 kg Find more here - / Contact us at -
Height=1.6 m, Overall length= 1.6 m, Overall width= 1 m, Suitable for soft dough. Working, good conditions.
Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg
Pallet labeling system Type: Pallet labeling system with Zebra Xi4 / RXi4 printing and application unit The pallet labeling system is used for variable marking of pallets with labels at different heights and up to two sides of the pallet (front and side surface). The integrated ZEBRA Xi4 / RXi4 industrial printer prints production-relevant labels (e.g. with barcode, batch or article number) and automatically applies them to the pallet. This ensures clear product and shipping labeling. The system can reliably label both loaded pallets and other containers and can be flexibly integrated into existing conveyor and packaging lines. Features: Variable labeling height (automatic height adjustment) Labeling on 1 or 2 pallet sides Industrial-grade Zebra Xi4 / RXi4 thermal transfer printer Automatic application via swivel arm Integration into existing conveyor lines possible ...
Height=1.6 m, Overall length= 1.6 m, Overall width= 1 m, Producer: Eberhardt condition: refurbished In stock Made in Germany Description In excellent working condition fully refurbished bun rounder Eberhardt Piccolo 4 can divide and process even the most sticky soft dough – Easy to clean removable top cover – Rust-resistant light metal cutting head – Dimensions 6359134 cm – Power 0,55 kW – Voltage 400 V amperage 1,7A – 30 divisions processing 40-135 g dough pieces – 3 moulding plates included
Max. punching force: 100 kN Max. stroke: approx. 50 mm (adjustable via clamping lever) Stroke actuation via footswitch Weight: approx. 600 kg
Injection moulding machine for PET preforms
Injection moulding machine for PET preforms
Injection moulding machine for PET preforms
Maximum Diameter: 110 mm // Minimum Diameter: 32 mm
Output (Packs Per M?Inute): 45 U/min // Type : Barrel
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 45 to PRESS TABLE table surface (left-right): 700 mm table surface (front-back): 440 mm opening in bed (diameter): 40 mm SLIDE table surface (left-right): 410 mm table surface (front-back): 280 mm stroke rate (max.): 110 /min SLIDE (MECHAN. PRESS) slide adjustment: 65 mm stroke min.: 0 mm stroke max.: 90 mm main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 380 mm distance between columns (H-frame): 360 mm ATTACHMENTS (PRESSES) 2-hand engagement: yes foot engagement: yes European CE standards: yes
APV PASTEURIZATION SYSTEM FOR FISH BROTH 1,000 LITRES/HOUR Automatic system designed for the pasteurization of 1,000 litres/hour of strained fish broth for subsequent packaging. Manufacturer: APV Year: 2002 OPERATION DESCRIPTION: - Inlet temperature: 20 °C - Process temperature: 105 °C - Outlet temperature for packaging: 35 °C The whole process consists of different stages that can be programmed using the control panel: 1. Sterilization: carried out by the circulation of hot water at a temperature of 115-120 °C for 30 minutes. 2. Production with water: cooling water flows inside the circuit until the process temperature that will be applied to the product is reached. 3. Production: the unprocessed product is fed into the regulation tank and then the production phase takes place in the circuit. 4. Cleaning-in-place: the installation is cleaned in place by ...
maximum number of results exceeded
please refine your search
