bending used for sale

Bending direction: clockwise, steel tube diameter: 50mm, steel tube thickness: 3mm, stainless steel tube diameter: 50mm, stainless steel tube thickness: 2mm, max. section modulus: 5cm³, bending angle: 180°+10°, max. tube length: 2000mm, max. radius range: 150mm, bending height: 1050mm, bending head length: 850mm, min. bend spacing: 400mm, nominal pressure: 250bar, operating pressure: 200bar. Machine dimensions X/Y/Z: approx. 3200mm/1400mm/1300mm, weight: approx. 1500kg. Documentation available. An on-site inspection is possible.

Shaft Ø: 40 mm Bending Capacity: Flat bar upright at 500 mm Ø: 60 x 10 mm flat at 400 mm Ø: 100 x 15 mm square at 500 mm Ø: 35 mm L-iron leg outwards at 450 mm Ø: 50 x 50 x 6 mm L-iron leg inwards at 600 mm Ø: 50 x 50 x 6 mm T-iron T outwards/inwards at 600 mm Ø: 60 x 60 x 7/50 x 50 x 6 mm Round bar at 500 mm Ø: 35 mm Shaft speed: 7.5 rpm electr. Connection: 380 V, approx. 1.7 kW Space requirement: 910 x 640 x 1400 mm Weight: approx. 400 kg

Workforce: 300 kN/30 t Tool height: 200 mm Stroke length: 0 - 300 mm Bending capacity with prism tool MW 125/240: 200 x 16/200 x 24 mm Bending speed: 0 - 1.3 m/min Drive motor: 380 V, 5.5 kW Weight: 800 kg Footprint: 1250 x 820 x 1120 mm

Specifications: Pressure: 50 t Bending length: 2000 mm Equipment: - Backgauge - Emergency stop push button - Foot control

sheet width: 1070 mm plate thickness: 4 mm distance between columns: 1100 mm diameter of upper rolls: 110 mm total power requirement: 5,0 KW weight of the machine ca.: 1,2 t dimensions of the machine ca.: 2,0 x 0,9 x 1,1 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mm plate thickness: 9.0 / 10,0 mm distance between columns: 1070 mm diameter of upper rolls: 190 mm pre-bending capacity: 9,0 mm connected load: 5,3 kW weight of the machine ca.: 2,4 t dimensions of the machine ca.: 2,7 x 0,92 x 1,2 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 25514 Specifications: - Max. working length 3060 mm - Column passage 2690 mm - Max. pressing force 1300 kN - Max. distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 215 mm - Lifting speeds - Downward speed idle max. 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 to. 11 mm/sec - Total drive power 18 kW - Pneumatic connection 6 bar - Space requirement approx. W 3800 x H 2700 x D 2400 mm - Weight approx. 11500 kg - with: - with 6 axis CNC control DELEM - Two-hand control panel with foot switch - crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Upper + Lower Tool Clamping - Die table displacement pneumatically supported

Offer 25513 Specifications: - Max. working length 2050 mm - Column passage 1750 mm - Max. pressing force 850 kN - Distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 365 mm - Lifting speeds - Rapid traverse downward speed 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 - 11 mm/sec - Total drive power 13 kVA - Space requirement approx. W 2700 x H 2900 x D 2100 mm - Weight approx. 9100 kg - with: - with 5 axis CNC control DELEM , DA - Y1 + 2 ; X ; R ; Z - Two-hand control panel with foot switch - Controlled crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Tool clamping - Die table displacement pneumatically supported

Offer 25515 Specifications: - Max. working length 2050 mm - Column passage 1750 mm - Max. pressing force 850 kN - Distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 365 mm - Lifting speeds - Rapid traverse downward speed 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 - 11 mm/sec - Total drive power 13 kVA - Space requirement approx. W 2700 x H 2900 x D 2100 mm - Weight approx. 9100 kg - with: - with CNC control DELEM , DA - Two-hand control panel with foot switch - Controlled crowning device - Back gauge with height adjustment 5 - 860 mm - hydr. Tool clamping - Die table displacement pneumatically supported - Sharpening tool + V-die

Hand-operated 3-roll sheet metal round bending machine with asymmetrical roller order Specifications: - Working width max. 1020 mm - Material thickness max. 1.5 mm - Roller diameter 64 mm - Upper roller turned into a crown, can be swung forward - Rear shaft with handwheel diagonally adjustable for conical rounding - Lower roller adjustment with control lever and eccentric - Front shaft parallel - Space requirement approx. W 1250 x H 950 x D 750 mm - Weight approx. 200 kg

A cassette set of bending tools for FASTI MAK

Diameter of bending rollers 550 mm Drive Type Hydraulic Main motor power30 kW

sheet width: - mm plate thickness: - mm distance between columns: - mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Equipment: 1 pliers feed right 4 Carriage Units Working Range: Wire thickness range: 0.5 - 2.0 mm Band width: up to 10.0 mm Length of move; up to 100 mm Output: up to 300 rpm

Equipment: 1 Carriage Feed Right 1 eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Working Range: Wire thickness range: up to 6.0 mm Strip width: up to 80 mm Feed length: up to 250 mm Power: 10 - 250 rpm

TECHNICAL DETAILS Sheet width: 1500 mm Sheet thickness: 6 mm MACHINE DETAILS Hfebqxim Iohy Alijqob Machine weight: approx. 1950 kg

Equipment: 1 piece BIHLER noise protection cabin 1 piece pliers feed right 1 piece eccentric press 70 kN 4 Norma sled units 1 piece narrow sled unit Working Range: Wire thickness range: 0.5 - 3.5 mm Strap width: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm

Key data: 170 t

Trumpf Press Brake Trumabend V170, 1700KN, Stroke: 365,. L-530cm, W- 240cm, H-300cm, Weight: 18to,

Stock number: 4017 PROFILE BENDING MACHINE Manufacturer: Roundo , Type: R4 Machines NO.: 1735, Year of manufacture: 1977 Specifications: Angle steel 90x9 mm Flat steel 200 x 30 mm Frame steel upright 100 x 18 mm Round steel 60 mm Load by steel 40 Kg/mm2 30 cm3 Upper roller 275 mm Ø Shaft dia. 105 mm Square steel 55 x 55 mm T-steel 90x10 mm Total power 5.5 kW Length: 1500 mm, Height: 1400 mm, Width: 1400 mm, Weight: 2500 kg

Press brake Manufacturer: AMADA PROMECAM Type: HFB 125/40 Year of Make: 1991 Control: DELEM DA 58 Press force max:. 1,250 kg Stroke max.: 180 mm Sheet thickness 8 mm Working width/passage: 3.7 m Number of phases: 3 Power consumption: 11 kw Voltage/Frequency: 380/50 Rated current: 24 Weight: 9,900 kg Availability: immediately Reference Number: L2131

Key data: 200 t

Horizontal Hydr. Straightening and bending press, 200 tons, hand and foot control, hydraulics. 18kw, with bending tools.

A semi-automatic NC tube bending machine Tracto-Technik is available. Tube diameter: 48mm, max. tube length: 3000mm, max. material thickness: 4mm, max. bending angle: 180°, max. bending radius: 125mm, bending accuracy: +/-0.2°, bending speed: 20°/s. Machine dimensions X/Y/Z: approx. 3900mm/800mm/1250mm, weight: approx. 700kg, control system: Siemens Simatic. Documentation available. On-site inspection is possible.

Material width 150 mm, material thickness 0.5 -3.0 mm Colour: green Total power requirement: 380 V Weight: 350 kg Dimensions: 800 x 1200 x 1350 mm Roller diameter: 24 mm Machine number 700257

Key data: 3000 mm, 8 mm

3-roll bending machine / round roller Schäfer SRMVHY – fully functional For sale is a used 3-roll bending machine (round roller / sheet metal bending machine) from the manufacturer Schäfer, model SRMVHY, built in 1992. The machine is in fully functional condition and is ready for immediate use. The rollers are hydraulically adjustable, which allows for precise and comfortable adjustment. The round bending machine is ideal for bending sheet metal in workshops and production plants. Technical data: Manufacturer: Schäfer Model No.: SRMVHY Year of Make: 1992 Max. sheet width: 3,000 mm Max. sheet thickness (mild steel): 8 mm Roller diameter: approx. 200 mm Voltage: 380 V Dimensions (L x W x H): approx. 5,300 x 1,800 x 1,300 mm Condition: used, fully functional Equipment: hydraulically adjustable rollers Changes and errors in the technical data, ...

Fasti 2040 x 5 mm Number of rolls: 3 rolls Roll capacity cold: 2040 x 5 mm Roll dia upside: 160 mm Power needed: 7,5 HP Length: 3250 mm Depth: 900 mm Hight: 1300 mm Weight: 3100 kg

Type: 108 Number of rolls: 3 rolls Roll capacity cold: 2540 x 2,5 mm Roll dia upside: 140 mm Dia under roll - side rolls: 140 mm Power needed: 5 kW Weight: 1760 kg

De plaatdikte is afhankelijk van het profiel. dop: 0,5 gt; 1,5 mm 7 stations vermogen: 2,4 kW gewicht: 430 kg

A CNC flat wire vertical wire bending machine V&C GmbH is available. Wire thickness range: 0.8mm-10mm, max. wire width: 30mm, min. winding inner diameter: 20mm, max. winding outer diameter: 250mm, max. winding height: 160mm, max. winding height with holding rod: 500mm, max. winding length: 250mm, min. bending radius: R6°, max. number of edges: 12/revolution. Machine dimensions X/Y/Z: approx. 2650mm/1000mm/1800mm, weight: approx. 800kg. Documentation available. On-site inspection is possible.

This LAFRANCONI LM 400 die bending machine was manufactured in 2020. It features a NC roller feeder, a max stroke rate of 350 1/min, and a material width capacity of 60 mm. The machine operates with a 20 KN center ram force and a 45 mm stroke. Powered by a 10.6 kW asynchronous spindle motor, it adjusts from 20 to 350 rpm. Dimensions are approximately 2450×1300×1900 mm. Contact us for more information about this machine.

This AMADA Vipros 255 was manufactured in 2001. It is a used punching and bending machine, ideal for those looking to enhance their metal fabrication capabilities. Contact us for more information about this machine.

This 6-axis MACRI Provar 6-45 U-D was manufactured in 2018. A fully automatic CNC tube bending machine, it features minimal use with only around 20 working hours. It supports a max tube diameter of Ø45 × 4 mm and a usable tube length of 5,800 mm. Key capabilities include a max bending speed of 150°/sec and a max push speed of 1,000 mm/sec. Consider the opportunity to buy this MACRI Provar 6-45 U-D profile bending machine. Contact us for more information.

This MACRI PROVAR 6-45 U-D was manufactured in 2022. It features a maximum steel bending capacity of Ø 45x4 mm and stainless steel up to Ø 40x3 mm. With a bending angle of up to 190° and speeds reaching 450 mm/sec on the X axis, this roll bending machine ensures precision and efficiency. Consider the opportunity to buy this MACRI PROVAR 6-45 U-D roll bending machine. Contact us for more information about this machine.

Offer 26016 Technical data: - Max. working width 2040 mm - max. material thickness at 40 kg / mm² strength 4 mm - Bending angle adjustment electronically pre-selectable 0 - 135 ° - Automatic follow-up control for a complete workflow - Largest opening width / stroke of the upper beam 350 mm - Height adjustability - bending beam 100 mm - The lower beam 100 mm - Upper bolster drive 400 V / 4 kW - Bending beam drive 400 V / 4 kW - Accessories - motorized bending beam adjustment - Backgauge adjustable with handwheel - E-foot button - Space requirement with back gauge - approx. W 3200 x H 1650 x D 2100 mm - Weight approx. 4500 kg

This TFM GM-SB-38CNC-2A1S was manufactured in 2019. It features a max bending capacity of 38 × 2 mm, bending speeds up to 65 °/sec, and motor power of 4 kW. Ideal for precise bending with a max bending angle of 180° and effective length over mandrel of 3200 mm. Consider the opportunity to buy this TFM GM-SB-38CNC-2A1S profile bending machine. Contact us for more information.

Offer 26008 Technical data: - 3 mot. driven rollers with asymmetrically hydr. Feeding of the two lower rollers - bends e.g. flat bars 100x40 flat up to Ø 600 mm - bends e.g. flat bars 100x20 upright up to Ø 800 mm - bends e.g. U 180x70 up to Ø 800 mm - Shaft diameter per 100 mm - Useful length of the standard shafts approx. 250 mm - Shaft rotation 5.4 rpm - Roller diameter 315 mm - Drive 400 V / 11 kW - With: - Separate control panel with digital actual value displays - Lateral straightening rollers manually adjustable - Standard bending kit for flat and angle material - Weight approx. 3500 kg - Space requirement approx. W 1600 x H 1700 x D 1600 mm

This Sahinler HKP-Z 100 was manufactured in 2016. A robust C-frame PLC controlled deep drawing press, it features a pressure force of 1000 kN and a stroke of 500 mm. The machine includes a large table size of 900x600 mm and a throat depth of 300 mm, suitable for diverse punching and bending tasks. Consider the opportunity to buy this Sahinler HKP-Z 100 punching and bending machine. Contact us for more information about this machine.

BPR BA 35 Asymmetrical CNC tube and profile bending machine with 3 driven rolls Factory REMANUFACTURED, RETROFITTED and UPGRADED in 2020. AS-NEW CONDITION MACHINE ! Contact: info@roce.hr / roce.strojevi@gmail.com Reason for Sale: Very low operating hours. Stored for years as a properly packed backup machine. In 2020, it was sent to the original manufacturer for full factory refurbishment and modernization (although fully functional at the time). After refurbishment, it was again kept in storage as a reserve unit. Now sold only because it is no longer needed as backup capacity. Excellent condition. Ready for immediate use. Description: This CNC-controlled profile bending machine is designed for complex bending operations with continuous radius variation. It allows choice between automatic and manual operating cycles, providing flexibility for different produc ...

This 3-axis Finn-Power Shear Genius TRS 6 SBU was manufactured in 1996, featuring a punching force of 300 kN and a sheet working range of 2500 mm × 1250 mm. It supports up to 21 tool stations and can handle sheet thicknesses up to 6 mm. Automatic tool change system enhances productivity. Consider the opportunity to buy this Finn-Power Shear Genius TRS 6 SBU punching and bending machine. Contact us for more information.

Key data: 3500 mm, 12 mm

Schäfer SVRM 3500/12 - CNC 4-roll bending machine - Siemens CNC control with joystick for roller positioning and digital display (renewed in 2006) - Hydraulic tilting of the upper roller by control panel - Rollers made of quenched and tempered material with a strength of 900 N/mm² - Year of construction 1989 Technical data - Max. sheet width: 3500 mm - Bale length of rollers: 3550 mm - Max. sheet thickness bending: 12 mm - Max. sheet thickness bending 4xS/3xS: 8 / 6 mm - Max. insertion limit of the sheets at 20% work hardening: 380 N/mm² - Upper and lower roller diameter: 360 mm - Side roller diameter: 290 mm - Smallest radius to be achieved: 220 mm - Feed speed lower roller: 200 mm/min - Feed speed side rollers: 700 mm/min - Total installed capacity: 22 kW - electr. Control: 380 V / 50 Hz / 3 Ph - Machine weight: 21100 kg

This 6-axis PEDRAZZOLI Bend Master 42 MRV IMS CNC was manufactured in 2001. It features a max tube diameter of 42 mm, a min tube diameter of 6 mm, and a max bending radius of 270 mm. With a power of 22 kW and a bending length up to 3000 mm, consider the opportunity to buy this PEDRAZZOLI Bend Master 42 MRV IMS CNC roll bending machine. Contact us for more information about this machine.

B50 - Mech. Bending machine -Technical data see data sheet

This SCHRODER-FASTI FASTI 509-40-6 was manufactured in 1997. A Hydraulic shearing machine capable of handling aluminum up to 8mm, steel up to 6mm, and stainless steel up to 3mm. Minimum stop dimension is 15mm. A solid choice for shaping various metals, the SCHRODER-FASTI FASTI 509-40-6 machine we have for sale. Contact us for further details.

Press brake Beyeler RT 80x3100 BJ 1992

Module was changed because a PCSS conversion took place on the machine and therefore this module no longer fits. Fully functional.

Amada HFE 80-25 Year: 11/ 1999 Working length: 2550 mm Stand width: 2125 mm Pressing force: 80 tons CNC control: AMADA OPERATOR II graphic Controlled axes: Y1/Y2; X1/X2; R1/R2; Z1/Z2 mot. adjustable back gauge Stroke: 200 mm Projection: 420 mm Crowning Working height: 960 mm Engine power: 9 kW CE mark Dimensions (length x width x height): approx. 3000 x 2250 x 2250 mm Weight: approx. 6 tons

Offer 26046 Technical data: - 2 mot. Driven rollers - Manual. Lining of the upper roller - Shaft diameter 30 mm - Shaft rotation 6 rpm - Roller diameter 88 - 108 mm - Bending capacity approx. - Flat steel 50 x 8 mm - Square 20 mm - Round tube 42 mm - Drive 380 V / 0.55 kW - with: - Right / left – run - Tube roller set approx. 16 mm - Weight approx. 150 kg - Space requirement approx. W 650 x H 1300 x D 950 mm

Used, technically overhauled reinforcing steel bending machine. 4 pieces of counter retaining strips. 2 footswitches with emergency stop function. Max. bending power 2 rods 28mm D. Bending speed 6/13 revolution.min. Control Siemens Touch Display CC Power 4 KW.

PCSS for conversion of the machine from PCSS-F to PCSS-A. Small restriction: When the machine was started up after a long standstill, the reference run had to be repeated several times. After a successful homing run, the part works without any problems.

Used, technically overhauled reinforcing steel bending machine. 4 pieces of counter retaining strips. 2 footswitches with emergency stop function. Max. bending capacity 1 rods 28mm D. Bending speed 6/16 revolution.min. Control with bending pins for three angles adjustable by hand. Power 3.5 KW.

Offer 26035 Technical data - Three driven rollers, each roller hydraulically adjustable - For bending and conical rolling, side bracket can be swivelled out - Operation of swivelling control panel with digital actual value displays - Max. working width 3050 mm - Max. sheet thickness at 400 N/mm² without bending 20 mm - Bending at bending diameter min 5 x top rolling. 16 mm - Upper roller diameter 340 mm - Side roller diameter 250 mm - Lower roller diameter 300 mm - Drive 400 V / 9.5 kW - Working speed adjustable - Space requirement approx. W 6200 x H 1650 x D 1650 mm - Weight machine approx. 16000 kg - Total weight machine + support mast + support arm 19500 kg with: - Extended roller ends for attaching profile rollers - Conical bending device - Side support arm hydraulically movable - Upper support mast hydraulically movable