bender used for sale

Reinforced steel scissors Round iron scissors Scissors Manufacturers Muhr and Bender Type 50N/22 and 50N/28 50N/22 intersects at 450N/mm2: Round: 22mm Square 22mm Flat: 35x10mm 50N/28 intersects at 450N/mm2: Round: 28mm Square 24mm Flat: 40x15mm Both machines new and ovp Special price

Hand lever plate and profile steel shears heavy and stable outing cuts sheets, round steel (approx. 15mm), flat steel and T-profiles Mounted on base Special price

round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications Ø tubes / radius in mm: Ø 22 / 67 Ø tubes / radius in mm: Ø 10 / 36

Used machine in good condition. Available for immediate delivery. - Operating hours: 34.027 - Control: Siemens Sinumerick 840D NC - Bending length max: 2.500 mm - Length min between the bends: 350 mm - Width min between the bends: 160 mm - Bending height max: 200 mm - Min length sheet: 370 mm - Max length sheet: 2.850 mm - Min sheet width: 180 mm - Max sheet width: 1.500 mm - Bending width max: 1.500 mm - Number of bends per side max: ilimitado / unlimited - Material thickness min: 0,5 mm - Maximum material thickness aluminium: 4 mm - Maximum material thickness steel: 3,2 mm - Maximum material thickness stainless steel: 2 mm - Max panel diagonal: 3.000 mm - Angle tolerance: +/-0?25 C? +- - Bending angle: -135? ... +135? C? - Bending tolerance: +/-0,15 mm +- - External bending radius min: 1,5/2 x espesor chapa / sheet width mm

connected load frequency: 220 V rated current: 263/152 : 01516 81 663 694 weight of the machine ca.: 1 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width - max.: 200 mm plate thickness: 6 mm flat steel: 70 x 7 mm round bar steel: 13 mm weight of the machine ca.: 50 kg dimensions of the machine ca.: 800 x 500 x 1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 25059 Specifications: - Bending capacity pipe at 45 kg / mm² to Ø 48 X 3.5 mm - Solid material up to 30 mm - Bending angle 0 - 180 ° - Largest average bending radius Rm 225 mm - Smallest inner bending radius Ri 10 mm - Drive 220 V / 1.7 Kw - Space requirement approx. W 400 x H 950 x D 600 mm - Weight approx. 100 kg - with - bending angle preselection - Digital bend angle display + bend angle fine adjustment - Bending tools , Ø 1/2" R 67 mm, Ø 1" R 67 mm ,

tube diameter: 60 mm wall strength: 3 mm bending radius min.: 2 x Rohr-Ø ÷ R200 mm bending angle: 0 - 180 ° gas tube pipelines: 2 (60.,3mm) mm speed: stufenlos 0,5 - 2,0 total power requirement: 1,5 kW weight of the machine ca.: 0,7 t - Powerful mandrel bending machine up to 2 gas pipe (60.3mm) in semi-automatic design (6000 mm pipe slide length) - Electromechanical drive of the bending axis - hydraulic clamping - mandrel feed / extract - 30 programs x 9 bending angle + correction angle The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 30.0 t punching cross-cut in cmm: 30.0 in 9.0 mm stroke: ca. 35 Hub/min throat: 610 mm stroke - stepless adjustable: 0 - 28.0 mm oil volume: 35.0 l work height max.: 1010 mm total power requirement: 4.0 kW weight of the machine ca.: 1200 kg. range L-W-H: 1400 x 700 x 1600 mm good condition () with a lot of application tools (stamps/dies) Furnishing: - electro-hydraulic hole punch, with large throat - Material/sheet metal scrapers including scraper plates - Large material support table, with adjustable depth stops - continuous stroke adjustment - freely movable foot switch including protective cover - Forklift pockets for easy transport - side storage area - lots of accessories + tools - including tool cabinet - Matrix base (for special size matrices) - Stamp holders (for special size stamps) - original user manuel The data for this ad was created with ModulMWS - the softwar ...

Mubea Hole Punch Model KL 750 Optima Year of manufacture 1990 fully functional Hebqowr Dk Rjxim Iqsfb Max. punching force 750 kn Triggering stroke via foot switch With very extensive tools, see photos

Magnetic Drilling Machine, Magnetic Drilling MachineCore Hole Drilling Machine, Metal Core Hole Drilling MachineDR. BENDER Type EK 323Masch No. 180543 year of construction approx. 1988Drilling capacity 23 mmSpindle holder MK 2Spindle speed 160 / 400 / 1250 rpm. Magnet 215 x 105 mmDrilling unit 220 Volt, 50 Hz, 1025 WattE-Magnet 220 Volt, 50 Hz, 65 Watt- Spindle speed via 3 gear stages- Left and right rotation- E-magnet KOCH, type KL32/6- Drill head height adjustment guided in a linear guide- Manual expulsor- Drill stand on

workpiece thickness max.:80 mm workpiece thickness min.:5 mm plate size without being adjusted:2000x1000 mm size of plate min.:100x100 mm control:CNC Mubea Matic100 hole diameter:min/max:10/40 mm workpiece weight:750 kg deburring device max.:d=40 mm traversing speed:80 m/min work height max.:1050 mm positioning accuracy:+/- 0,5 mm opening of gripping pliers min/max.:Typ I: 5/45 mm opening of gripping pliers min/max.:Typ II: 45/85 mm feed length:max. 150 mm rapid traverse::8 m/min spindle turning speed range:112-180-224-280-355-560 U/min work table::L:2500;B:950 mm arm gripping device:4 Stück tool taper:Kegel DIN 6327 longitudinal travel:x=2800 mm cross travel:y=1000 mm bore spindle stroke:max. 150 mm total power requirement:25,0 kW weight of the machine ca.:5,5 t space requirements approx. LxWxH:5,0x5,5x2,7 m plate size with beeing adjusted also 1000x4000 mm possible with roller conveyo ...

Offer 26137 Technical data: - Flat steel shears - knife length 360 mm - For flat material 350 x 13 mm - or 230 x 20 mm - Profile steel shears - L-steel at 90° 140 x 13 mm - at 45° 70 x 7 mm - T-steel at 90° 70 mm - Steel bar shears - round steel 50 mm - Square steel 42 mm - Notching device - for material up to 12 mm - Right notching up to 52 x 90 mm - Hole punch - punching force approx. 550 KN - - Stroke infinitely variable 0 - 60 mm - Perforates in steel up to 30 mm Ø in 16 mm - Projection 320 mm - Hydraulic drive 400 V / 5.5 kW - Two separate working cylinders and separate foot switch - Space requirement approx. W 1400 x H 1600 x D 750 mm - Weight approx. 1300 kg - with: - various punches + dies in a separate tool cabinet - Support stop table - Stop

Plate bender Heidelberg, fit\'s from size 52 up to 105, max. plate lenght 811 mm; Ready for operation

max. plate width: 80 cm stamp width: 425 mm serial no.: 174 plate punch autoplate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Profile bending machine, bending machine, pipe bending tool -Handover: in the current condition as viewed -Accessories: 1 damaged pressing tool: 3/4, see photos -suitable for: pipe size 1/2 to 1 1/2 -Dimensions: 630/670/H440 mm -Weight: 36 kg

Hand bending machine Flat bar max. 16 mm Square steel 16 mm Round steel 16 mm Weight 45 kg Bending angle max. 180 ° Dimensions L x W x H 0.4 x 0.4 x 1.1 m

max. plate width: 80 cm stamp width: 425 mm serial no.: 564 plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 55 cm stamp width: 220 mm serial no.: 10101/09 plate clamping system: autoplate plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 55 cm stamp width: 220 mm serial no.: 10101/09 weight: 12 kg dimensions of press (L x W x H): 70 x 13 x 55 cm plate clamping system: Autoplate for QM 46 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 80 cm stamp width: 425 mm serial no.: 1132 Plate punch for Heidelberg S-Offset The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 80 cm stamp width: 425 mm serial no.: 5136 Plate punch for Heidelberg S-Offset The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 52 cm stamp width: 220 mm serial no.: 16548 plate punch for GTO or QM 46 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stored in working condition. The buyer must provide his own transport. Elevator available to charge it.

equipped with 2x 20ton hydraulic jack

max. plate width: 50 cm stamp width: 220 mm serial no.: 4184/20 Dimensions (L/W/H): 60x20x50 mm plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 920 cm stamp width: 425 cm Dimensions (L/W/H): 550/1000/1220 cm plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 74 cm stamp width: 340 mm serial no.: 13434 dimensions of press (L x W x H): 80 x 95 x 120 cm weight: 100 kg Thermo plate bender for The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 52 cm stamp width: 220 mm serial no.: 3851/15 Dimensions (L/W/H): 60x20x50 mm plate punch QM 46 or GTO The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 1520 cm stamp width: 780 mm dimensions of press (L x W x H): 150 x 58 x 128 cm plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

stamp width: 425 mm serial no.: 6660/39 Dimensions (L,W): 71 x 55 cm plate punch for SM 52 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

MACC Iron Bender "Piegaferri" Steel construction with hardened jaws 100 x 7 mm Vise with eccentric clamping Footprint 330 x 330 x 300 mm Weight approx. 35 kg

Plate bender, machine number 3986/47, year of manufacture 1998, in good condition, immediately available If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.

Buchdeckenausbiegemaschine - Case Bender Orient CX Year 1993 - Serial- No. 9384/15344 Working width max. 500mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

CONTROLS   CNC controls SIEMENS TECHNICAL SPECIFICATION   Max. diameter of tube: 120 mm   Max. bending radius: 180 mm ELECTRICAL SPECIFICATIONS   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   space requirements -left/right-: 8000 mm   space requirements -front/back-: 2600 mm   total height: 2300 mm   total weight approx.: 16500 kg machine in a very good condition Machine in very good condition Special features: - Free-form bending option - Laser scanner for securing the bending area - Foot pedal for safe start - Bending simulation Automation: - CNC control BEND MOTION CONTROL - Automatic mandrel lubrication as MMS Retrofit 2018: - Control system retrofit - Cables replaced - Bending head overhauled - Guides replaced - complete equipment (see photos) (Ø22x2, Ø28x2, Ø38x2.6, Ø42.4x2.6, Ø48.3x2.6, Ø60.3x2.9, Ø76.1x3.2, Ø88.9x3.2, Ø114.3x3.6 ...

Profile bending machine, bending machine, flat bar bender, horizontal bending/straightening press -Flat bar bender: hydraulic profile bending machine -Base: on casters, table folds on both sides -Operating mode: Manual and automatic operation -Accessories: see photos -Overall dimensions: 2155/1320/H1070 mm -Transport dimensions: 1320/840/H1245 mm -Weight: 404 kg

Hand bending machine Height 100mm Weight 60 kg Dimensions 0.8 x 0.6 x 0.3 m Auction-ID: A7-46642-49

Material / Max Capacity / Min Radius Flat / 1 1/4\" / 10\" C Channel 1x2\" / 60\" Round Tube 1 1/2\" / 20\" Round Tube 2\"/60\" Diameter of rollers 1 1/2\" Maximum tube diameter 38 mm. Condition: never used / new (5) Auction-ID: A7-46642-173

Hand bending machine Flat bar max. 16 mm Square steel 16 mm Round steel 16 mm Weight 45 kg Bending angle max. 180 ° Dimensions L x W x H 0.4 x 0.4 x 1.1 m Auction-ID: A7-46642-242

Hydraulic Pipe Bender Compressive force 16t 8 pieces of bending elements from 1/2\" to 3\" Condition: never used / new (5) Auction-ID: A7-46642-71

Flat steel bending machine The following bending tools are included: 1\" - 1 1/4\" - 1 1/2\" - 2\", - 2 1/2\", - 3\" Bending tools diameter 1\" to 3\" mm Wall thickness max. 16 mm Machine weight approx. 26 kg Package size max. 0.6 x 0.3 x 0.3 m Condition: never used / new (5) Auction-ID: A7-46642-171

Stored in working condition. The buyer must provide his own transport. Elevator available to charge it. Auction-ID: A3-43538-17038

Auction-ID: A1-47154-199