be used for sale

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers,  ...

Mounted on wooden plate 245 x 123cm, Work table not included Auction-ID: A3-50009-41

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...

Auction-ID: A1-50347-179

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...

Auction-ID: A1-47447-412

Machine Table size approx. 2500 mm x 980 mm

Specifications Strip width: 500 mm Distance between side walls: 5 m Length: 40 mm Power connection: 0.75kW Threshold height: every approx. 400mm Motor power: 400V Threshold spacing: 550 mm

Describing Dutch car costs Export document in name 100 euros ignition switch broken Auction-ID: A3-46128-5371

Auction-ID: A3-46128-3526

Only start by using the kickstart. Year of construction 2013. Auction-ID: A1-47419-206

CNC processing centre with 5 axes Brand: Cosmec Type: Conquest 715 New machine Just an example for a configuration, other equipment is available on request: High-precision CNC - centre with camera centering system. Ideal machine for milling works in digital print, wood- and plastics as well as in the advertising technique Gantry drive system 5-axis main spindle complete interpolating Moving route: - X - axis 4.850 mm - Y - axis 2.630 mm - Z - axis 880 mm Working table: Vacuum grid table system, made out of Sandwich-Bakelit and, consisting of: - 1 Upper plate with grid 50 mm, also the use of COSMEC vakuum cups is possible (vacuum cups optional available) - 1 Lower plate with rectangular chanels for ideal vacuum distribution Dimensions: X - axis 4.210 mm Y - axis 2.210 mm Table can be split in 2 working fields Each field with 3 workpiece stops in X - d ...

The car starts and drives without any problems. Documents available, see photos for details. Auction-ID: A3-46128-4054

Auction-ID: A3-46128-12525

Sewer inspection system from RICO Auction-ID: A1-47419-140

CNC processing centre Brand: TecnoTeam Type: Enjoy Basic 3 Achsen New machine Save your space: Standing upright means progress for human! - With a vertical CNC machine you save a lot of space: Wether for consuming material or a further machine, you have more space to use in your storage. Easy machine use: - TPA makes the use very easy, you find this software at several well-known machine brands - You see the programmed processings on a virtual display, no matter which process: if circle, bow, linear millings or drillings, - Create job lists in the CAM - Forget the calculator, the machine calculates for you. - For this software several genious tips and tricks are possible. With realiability to success: - Technoteam uses High-Quality components from well-established producers. - We modify the machine exactly to your needs: If you process massive wood, you get a stro ...

The car starts and drives without any problems. Documents available, see photos for details. Auction-ID: A3-46128-4052

Auction-ID: A1-47392-270

Car can be pushed into motion Distribution belt and suspensions new Auction-ID: A3-46128-3528

without damage (except for minor signs of wear) Auction-ID: A1-47447-317

Transnorm conveyor belt GF 2200-600-500 RA2388 Technical data: Make: Transnorm Conveyor length (NL): 2200 mm Frame width (NB): 600 mm, 700 mm with motor Belt width (GuB): 500 mm Overall height (BH): 80 mm, 430 mm with motor Support feet: optionally available Conveyor speed (v m/s): 0,3-1,2 Drive: SEW geared motor, with Movi-Mot Frequency inverter for stepless speed change Electrical data: 50Hz V380-500, kW 0.37 S1 Drive pulley: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Lateral guide on one and both sides Adjustable length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2008 condition: good (used) Conveying length in mm: 2200 Nominal / outside width in mm: 600 Belt width in mm: 500 Driven: YES Engine type: SEW Movi-Mot KW: 0,37/S1 Conveyor speed m / s: 0,3-1,2 scope of delivery ...

Transnorm conveyor belt GF 2250-600-500 RA2389 Technical data: Make: Transnorm Conveyor length (NL): 2250 mm Frame width (NB): 600 mm, 700 mm with motor Belt width (GuB): 500 mm Overall height (BH): 80 mm, 430 mm with motor Support feet: optionally available Conveyor speed (v m/s): 0,15-0,80 Drive: SEW geared motor, with Movi-Mot Frequency inverter for stepless speed change Electrical data: 50Hz V380-500, kW 0.37 S1 Drive pulley: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Lateral guide on one and both sides Adjustable length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2008 condition: good (used) Conveying length in mm: 2250 Nominal / outside width in mm: 600 Belt width in mm: 500 Driven: YES Engine type: SEW Movi-Mot KW: 0,37/S1 Conveyor speed m / s: 0,15-0,80 scope of deli ...

3600 mm - 10 pcs Auction-ID: A7-50633-6

Working width: 1100mm, sanding units: 2, voltage/frequency: 380V/50Hz. An on-site inspection is possible.

CSM CNC38TBRE tube and profile bending machine was built in 2008 in China by CHIAO SHENG MACHINERY CO., LTD. The machine is designed for the precision bending of tubes, profiles and bars with a maximum diameter of 38 mm. It enables the production of parts with various shapes and bending radii, used in many industries. A maximum bending angle of 190°, combined with a wide range of bending radii, enables the production of both tight bends and parts with larger bending radii. Bending accuracy of ±0.01° ensures high precision and repeatability of the workpieces. The CSM CNC38TBRE is equipped with an intuitive CNC controller that facilitates day-to-day operation of the machine. The control system features a large memory capacity, allowing numerous user programmes to be stored. The CSM CNC38TBRE tube bending machine weighs 2500 kg. Technical specifications of the CSM CNC38TBRE tube be ...

MADO Selekta 2 MKB651 Bone Band Saw completely made of stainless steel with motor brake Safety shutdown of the door without function a rubber foot is missing otherwise in good condition, must be cleaned thoroughly before use Video about test run available

Manufacturer: Johannsen, Type: T 86, Year: 1991, Sanding hight mm: 350, Table width mm: 1200, Table length: 2800, Hight adjustment by engine: yes, Sanding belt engine kW: 4, Travel range table mm: 300, 2 rotary directions: yes, Exhaust diameter mm: 130, Hight adjustment by engine: yes, Year :1991

In used but good working condition Citroën Berlingo with tow bar and 3 seats. Auction-ID: A3-46132-17359

Auction-ID: A1-50335-26

with flight case Auction-ID: A1-48746-299

Manufacturer: Costa, Type: KA CCC 1350, Year: 2003, Control: Costa, Sanding width mm: 1350, Sanding hight mm: 160, Number of sanding belts: 3, Sanding belt dimensions: 1350 X 2620, Rollers: 3, Längsschleifaggregate: 3, Bürstenaggregate: 1, Steel roller: 2+1 Gummi, Bürstenaggregate: 1, Band 1 Leistung kW : ca.20, Band 2 Leistung kW : ca.20, Band 3 Leistung kW : ca.20, Continous adjustable feeding speed m/min: 5-15, Transportbandantrieb kW: 2,2, Constant table hight: yes, Brushing unit: yes, Year :2003

Manufacturer: Purete, Type: PRT-C1113, Year: Neumaschine, Control: yes, Working length mm: 5000, Working widht mm: 1300, Frequency converter: yes, Own controller: yes, Engine power kW: 0,7, Feeding speed min-max m/min: 5-25, elektronisch regelbar: yes, Feeding speed continous adjustable: yes, Working hight adjustable mm: 900 +-50, Year :Neumaschine

Manufacturer: Biesse, Type: Selco EB 108, Year: 2008, Program: Selco Optiplaning, Optimisation: Selco Osi Plus, Max plate format mm: 4200 X 2200, Saw blade protrusion: 107, Cutting lenght mm: 4200, Working hight mm: 95, Vorschub Sägewagen : 100, Network-capable: yes, Angle pressure fixture: yes, Saw Blade Diameter mm: 400, Säge verstellbar über Steuerung: yes, Number of clamping tools: 9, Main motor kW: 13,5, Feeding speed continous adjustable: yes, Feeding from front side: yes, Feeding speed continous adjustable: yes, Year :2008

Manufacturer: PRT-C1113 Purete Transportband Länge 4000-1300 mm, Type: PRT-C1113 , Year: NEUMASCHINE, Working length mm: 4000, Working widht mm: 1300, Total hight mm: 900, Belt width: 1320, Frequency converter: yes, Engine power kW: 0,4, Feeding speed min-max m/min: 5-25, elektronisch regelbar: yes, Working hight adjustable mm: yes, Year :NEUMASCHINE

Manufacturer: Transportbandkurve unbekannnt, Control: no, Belt transport: yes, Working hight mm: ca 450 mm, Engine power kW: ca.0.75, Wight approx. kg: 600,

Auction-ID: A1-48746-306

This 3-axis DYE RHE -3000 Bed Type Milling Machine was manufactured in 2009. It features a substantial table surface of 1000 × 3000 mm, with longitudinal travel of 3000 mm and transverse travel of 1500 mm. The machine is equipped with a grinding wheel diameter of 450 × 80 mm and a spindle speed of 1450 rpm. If you are looking to get high-quality milling capabilities, consider the DYE RHE -3000 machine we have for sale. Contact us for further details.

Manufacturer: Bütfering AWS, Type: AWS 1100, Year: 1981, Monting of the machine: Kombiaggregat, Sanding width mm: 1100, Sanding hight mm: 120, Sanding belt dimensions: 1900 X 1150, Längsschleifaggregate: Kombi/Bürste, Band 1 Leistung kW : ca.10, Combi unit roller/shoe: yes, Continous adjustable feeding speed m/min: yes, Transportbandantrieb kW: 0,5, Constant table hight: no, Year :1981

Manufacturer: Venyeskob, Control: no, Working length mm: 800, Working widht mm: 1400, Total hight mm: 900 verstellbar, Engine power kW: ca.1 kw, Feeding speed min-max m/min: ca.6-20, Feeding speed continous adjustable: yes,

Manufacturer: Heesemann, Type: LSM 8, Year: 2005, Sanding width mm: 1300, Sanding hight mm: 3-80, Sanding belt dimensions: 2620x1350, Konstantentisch: yes, Längsschleifaggregate: 1, Band 1 Leistung kW : 18,5, Band 1 Schleifbandgeschwindigkeit m/s : 0,5-20, Continous adjustable feeding speed m/min: 13-65, Transportbandantrieb kW: 7,5, Vacuum table: 5,5 kW, Brushing unit: 150 mm - 1,5 kW, Weight in kg: 6.500, Year :2005

Manufacturer: Weinig, Type: Kettenförderssysteme Vereinzelung, Working length mm: 6500 mm, Working widht mm: 2600 mm, Own controller: no, Engine power kW: ca 5, Working hight adjustable mm: 900 mm, FREE TEXT: 5 Mitnehmer Ketten mit 170 mm Abstand,

Manufacturer: Bürkle , Type: Tansportband, Working length mm: 2500, Working widht mm: 1300, Total hight mm: 980, Belt width: 1300, Own controller: no, Engine power kW: ca.0,5, Feeding speed min-max m/min: 10-30, Feeding speed continous adjustable: über Regler möglich, Working hight adjustable mm: yes, Movable: no,

Manufacturer: Venyeskob 2 Stück 90 Grad, Type: Transportbandkurve, Year: ca, Inner radius in mm: ca.4500, Working hight mm: 890, Feeding speed max m/min: 6-30, Engine power kW: ca 2 X 1,5, FREE TEXT: eine Kurve ist überbaut, Year :ca

Manufacturer: Bürkle UV Transportband, Type: ca.2005, Working length mm: 2630, Working widht mm: 1300, UV-Band: yes, Total hight mm: 890 +-, Bandsteuerung : yes, Engine power kW: ca.0,5, Feeding speed min-max m/min: 6-30, Feeding speed continous adjustable: über Umrichter möglich,

Manufacturer: Heesemann Lackschleifmaschine, Type: LSM 8, Year: 2002, Control: Heesemann, Monting of the machine: Längs/längs/Bürste /Bürste, Sanding width mm: 1300, Sanding hight mm: 120, Sanding belt dimensions: 2620 X 1350, Längsschleifaggregate: 2, Band 1 Leistung kW : 13/17, Band 2 Leistung kW : 13/17, Transportbandantrieb kW: ca.4,0, Intermediate sanding of lacquer: yes, Constant table hight: yes, Vacuum table: yes, Segment sanding shoe: yes, Brushing unit: 2, Year :2002

Manufacturer: Bürkle Transportband, Year: 2002, Working length mm: 3000, Working widht mm: 1400, UV-Band: no, Belt width: 1420, Own controller: no, Bandsteuerung : no, Engine power kW: 0,5, Feeding speed min-max m/min: 6-30, elektronisch regelbar: möglich, Feeding speed continous adjustable: yes, Working hight adjustable mm: yes, Year :2002

Manufacturer: Heesemann , Type: LSM 8 mit EA Entstaubung, Year: 2002, Monting of the machine: Walze/Quer/lang/lang/Lang/3 X Bürste, Sanding width mm: 1300, Sanding hight mm: 120, Number of sanding belts: 5, Sanding belt dimensions: 2620 X 1300, Steel roller: 1, Transverse sanding units: 1, Längsschleifaggregate: 4, Bürstenaggregate: 3, Band 1 Leistung kW : ca.35, Belt 1 shoe unit: yes, Band 2 Leistung kW : 17, Band 3 Leistung kW : 17, Band 4 Leistung kW : 17, Struckturieraggregat: Möglich, Vacuum table: yes, Year :2002

Manufacturer: Biesse Selco, Type: EBT 120, Year: 2008, Bench top saw: 4400x2200, Work piece length min-max mm: 4400, Work piece width min-max mm: 2200, Saw blade protrusion: 122, Vorschub Sägewagen : 1-150, Min-max feed programming slider m/min: 100, Saw Blade Diameter mm: 430, Main motor kW: 15, Feeding speed continous adjustable: yes, Scoring Aggregate : 2,2 kW, Work piece length min-max mm: 4400, Work piece width min-max mm: 2200, Feeding speed continous adjustable: yes, Year :2008