bar mill used for sale

x-travel: 600 mm y-travel: 400 mm z-travel: 420 mm Control: Heidenhain Tnc table-size: 900 x 460 mm turning speeds: 4000 U/min total power requirement: kW weight of the machine ca.: 2,9 t dimensions of the machine ca.: 3 x 2 x 2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 550 mm roll length: 1500 mm rolls drilled: Kernbohrung Nip adjustment: hydraulisch 0 total power requirement: 90 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 350 mm roll length: 700 mm rolls drilled: peripher Nip adjustment: hydraulisch 0 total power requirement: 2x 15 kW Condition: new, with CE mark, Specification: Two Roll Mill 350 x 700 mm - new - cylinder diameter: 350 mm - cylinder length: 700 mm - cylinder boring: peripherally drilled - cylinder bearings: with grease lubrication - 2 cylindera chromed - nip admustment: hydraulically - new hydraulic unit - tipper guiding plates of nylon-polyethylen-material - stainless steel tray - bi-directional bars - AC brake motors: 2 pcs, each 15 kW, 400 V, 50 Hz - bevel gearboxes of transmission: 2 pcs - painting: with RAL colours acc. to customer’s specification - complete machine protection with stainless steel carters - new electric cabinet - new electrical system - new machine on-board system - new control panel Touchpanel 7 - PLC system: 1 piece, brand Siem ...

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 110 by 135 mm -Drawing: in the photos -Dimensions: 210/90/H220 mm -Weight: 8.6 kg

roll diameter: 400 mm roll length: 1100 mm rolls drilled: Kernbohrung Nip adjustment: hydraulisch total power requirement: 2x 30 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

power capacity: 0 kW tool adaptor: 0 total power requirement: 0 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 1100 mm y-travel: 600 mm z-travel: 500 mm Control: Heidenhain TNC 335 B tool taper: SK40 table surface - upper: 1650 x 700 mm table face - lower: 1870 x 300 mm spindle speed:: 3000 Upm spindle motor: ca. 9 kW total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Horizontal and vertical milling Position change of the head is done manually Vertical head with drilling quill, drilling depth 100 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 22.000 mm y-travel: 1.500 mm z-travel: 3.000 mm Control: SIEMENS 840 D milling head -swivable: 0,001/0,001 Grad milling head: Universalfräskopf 45° Internal cooling system: 20 bar Chip coveyor: ja Tools changer: 30 pos. coolant: 1.100 l Tool taper: DIN 69871A ISO 50 total power requirement: 45 kW weight of the machine ca.: 68 t The round table shown in the pictures as well as the plate field are not sold with ! urning Speeds 6.000 r.p.m. AutoIndex Head 45 º Head 360.000 Pos. Elbow 360.000 Pos. Main Motor Power 37 Kw. Nº Change Range 2 Ranges Automatic Tool Charger INCLUDED Tools at ATC 30 Coolant Through Tool 20 Bar INCLUDED Soluble Oil Tank with filter paper INCLUDED Head Coolant System + CF Box INCLUDED Longitudinal Chip Conveyor INCLUDED Operator?s Platformd with 2000 mm Vertical movement. INCLUDED Ready for Rotor Translating Table (Regulator + Wires) /IN ...

Double end profiler, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -Circular saw motor in: flat design -Motor: 1.85 kW 2870 rpm at 50 Hz -Shaft holder: Ø 30 mm -Number: 2x motors available -Price: per piece -Dimensions: 390/120/H185 mm -Weight: 15 kg

Corundum disc mill Manufacturer: FrymaKoruma Type: MK-360/B Item #: 101031 Year of construction: 2007 Power: 45 kW Pressure product space: 4/3 bar Pressure double jacket: 6 bar Weight: 670 kg new grinding discs installed with control cabinet with double-acting mechanical seal various spare parts LBH: Mill: 1150 x 650 x 600 mm Control cabinet (large): 1000 x 290 x 1220 mm Control cabinet (small): 400 x 300 x 200 mm

Edge milling machine, edge milling device, chamfering machine, mobile milling machine, weld edge former, weld edge former, weld preparation, weld edge forming machine, deburring device, deburring machine -Edge milling: 0 - 3 mm -Drive: 0.45 kW -Angle: adjustable -Dimensions: 485/345/H250 mm -Weight: 18.2 kg

Tool holder, milling holder, milling tool -Number: 3x SK40 holders -various: versions -Sale: only complete -Weight: 6 kg

1 x used double-sided Rotoles S600 with 2 grinding units and 1x brush Working width 600mmm Speed 60m/min Calibration milling planing machines with feed rollers Best accuracy of the boards and excellent results in delamination attempts, at any speed. ROTOLES S calibration machines are the best choice for calibrating boards and slats before gluing. Rotoles S calibration milling planing machines with feed rollers Best accuracy of the boards and excellent results in delamination attempts, at any speed. ROTOLES S calibration machines are the best choice for calibrating boards and slats before gluing.

spindle diameter: 160 mm x-travel: 10.000 mm y-travel: 3.000 mm Control: total power requirement: 120/63 spindel kW weight of the machine ca.: 63 t dimensions of the machine ca.: 15x3.85x7.36 m Stocknumber 1210057 Type of machine CNC Floortype boring machine Make WOTAN Type Rapid 5C Build in 2004 Type of control HEIDENHAIN iTNC 530 Spindle diameter 160 mm X-stroke (mm) 10.000 Y-stroke (mm) 3.800 Z-stroke (mm) 700 W-stroke 700 mm Tool Taper Iso 50 Speeds (Rpm) 1,25 - 1250 Feeds (mm/R) 1 - 5000 mm/min Rapid feeds 5 mtr/min. Total Power (KW) 120 /spindel 83 Lenght (mm) 14.500 Width (mm) 3.850 Height (mm) 7.360 Weight 62.300 kg Additional information completely overhould in 2004 and retrofitted by Dorries Scharmann with CNC control HEIDENHAIN iTNC 530 - 4 different angular milling heads - hydrostatic spindle bearing - aerostatic guideways - coolant device - chip conveyo ...

Tool holder, milling holder, milling tool -Number: 2x SK50 holders -1x holder: Ø 27x 85 mm -1x holder: Ø 70 x 220 mm -Sale: only complete -Weight: 18 kg

table length: 4000 mm table width: 3000 mm table load: 60 t total power requirement: 14.3 kW weight of the machine ca.: 48.5 t dimensions of the machine ca.: m Brand: FX Type: 83.300/400 Used machine Digital readout: Heidenhain ND 780 Table length: 4.000 mm Table width: 3.000 mm Table load: 60 T Movement: 2.000 mm Width T-slots: 58 mm (M30) mm Feeding: 4 - 1.500 mm/min Rapid traverse: 4.000 mm/min Power: 14,3 kW Machine weight: 48.500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 3500 mm y-travel: 900 mm z-travel: 1000 mm Control: heidenhain tnc 415B total power requirement: 22 /spindel kW weight of the machine ca.: 16.5 t dimensions of the machine ca.: 7.2x3.9x3.2 m Make SORALUCE Type Soramill SL 5000 Built in 1995 Control type HEIDENHAIN TNC 415 B Table size (mm) 5000 x 800 mm X out (mm) 3500 Y-off (mm) 900 Z-off (mm) 1000 Maximum table load 12,5 ton Speed (RPM) 20-. 2,000 Tool holder ISO 50 Feed along (mm/Rev) 5 - 10000 mm / min. Rapid traverse 12 mtr/min. Gesamtleistung(kW) 22 Length (mm) 7250 Width (mm) 3900 Height (mm) 3200 Weight 16500 kg Additional information Automatically indexierender Swivel Head with 2 x 144 positions (2.5 ° pitch) in two levels above the control programmable Cooling medium institution The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

spindle diameter: 110 mm x-travel: 4000 mm y-travel: 2000 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 1210014 Type of machine Floortype Boring Machine Make PEGARD Type AF11 Type of control Conventional Spindle diameter 110 mm X-stroke (mm) 4000 Y-stroke (mm) 2000 Z-stroke (mm) 300/750 Table dimensions (mm) 1200 x 1600 mm Table rotation (degrees) 360 Tool Taper Iso 50 Speeds (Rpm) 4 - 1000 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 5000 mm y-travel: 3100 mm z-travel: 1200 mm Control: total power requirement: 20/27 kW weight of the machine ca.: 65 t dimensions of the machine ca.: 15x6,2x6 m Stock number 1110051 Machine type CNC Portal milling machine Make CORREA Rapid type 50 Year of manufacture 2004 Control type HEIDENHAIN Table size (mm) 5000 x 2000 mm X out (mm) 5000 mm Y-off (mm) 3100 mm Z-off (mm) 1200 mm Table load Max 15 ton Speed (RPM) Max 18,000 Tool holder HSK 63 Gesamtleistung(kW) 20/27 Length (mm) 15000 Width (mm) 6200 Height (mm) 6000 Weight 65 ton Additional information Tool changer for 24 tools 5-axis gesteuerd The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tool holder, milling holder, milling tool -Adjustment: SK50 -Recording inside: Ø 28 mm -Weight: 2.9 kg/piece

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Swallowtail: 278 by 218 mm 38 mm high -Drawing: in the photos -Dimensions: 450/95/H295 mm -Weight: 13 kg

spindle diameter: 160 mm x-travel: 10.000 mm y-travel: 3.000 mm Control: ICEM 402 total power requirement: kW weight of the machine ca.: 80 t dimensions of the machine ca.: m Stocknumber 1210050 Type of machine CNC Floortype Boring Machine Make SKODA Type W 160 CNC Build in 1974/retrofitted in 2002 Type of control ICEM 402 Spindle diameter 160 mm X-stroke (mm) 10.000 Y-stroke (mm) 3.000 Z-stroke (mm) 1600 W-stroke 1250 mm Speeds (Rpm) 1 - 1.200 Feeds (mm/R) 0,5 - 8.000 mm/min. Rapid feeds 8.000 mm/min Total Power (KW) 180 KvA Weight 80 ton The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 6000 mm y-travel: 2000 mm z-travel: 3000 mm Control: heidenhain TNC 415 total power requirement: 34 kW weight of the machine ca.: 31 t dimensions of the machine ca.: 7000 mm m Stocknumber 1110055 Type of machine CNC Floortype milling machine Make ZAYER Type KCU6000 Build in 1992 Type of control Heidenhain TNC 415 X-stroke (mm) 6.000 Y-stroke (mm) 2.000 Z-stroke (mm) 3.000 Speeds (Rpm) 20 - 1.800 Admission in spindlehead BT50 Feeds X (mm/R) 5 - 5000 mm/min Feeds Y (mm/R) 5- 5000 mm/min. Feeds Z (mm/R) 5- 5000 mm/min. Rapid feeds 10.000 mm/min. Total Power (KW) 34 Lenght (mm) 11.000 Width (mm) 2.500 Height (mm) 7.000 Weight 31.000 Kg Additional information Juaristi MG6 turntable: 1500 x 1200 mm Cooling system: 2.5 Bar Tool cooling: 15 Bar The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

spindle diameter: 160 mm x-travel: 15000 mm y-travel: 4000 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 1210060 Type of machine Floortype Boring machine Make SKODA Type W160HC Build in 1990 Spindle diameter 160 mm X-stroke (mm) 15.000 Y-stroke (mm) 4.000 Z-stroke (mm) 1.600 W-stroke 1.250 Tool Taper Iso 50 Additional information With 3 floorplates 1880x5615 mm en 3x 1880x6400 mm 3 millingheads and 1 support 1 rotarytable Skoda S-35 C, 35 ton 2800 x 3150 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Swallowtail: 145 by 185 mm high -Drawing: in the photos -Number: 1x counter bearing available -Price: per piece -Dimensions: 290/90/H210 mm -Weight: 14 kg

x-travel: 14.000 mm y-travel: 1.500 mm z-travel: 3.000 mm Control: Heidenhain Itnc 530 total power requirement: 50 kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 1110049 Type of machine CNC floortype milling machine Make FPT Type Spirit 130 Build in 2012 Type of control HEIDENHAIN TNC Itnc 530 X-stroke (mm) 14.000 Y-stroke (mm) 1.500 Z-stroke (mm) 3.000 Speeds (Rpm) max. 4.000 Admission in spindlehead Iso 50 Rapid feeds max 25.000 mm/min Additional information Program run 9655 hour The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 4000 mm y-travel: 1000 mm z-travel: 1000 mm total power requirement: 22 kW weight of the machine ca.: 25 t dimensions of the machine ca.: 10.000 x 6.000 x 4.250 m Brand: Soraluce Type: Soramill 4 TF4 CNC brand: Heidenhain CNC model: TNC 415 B Year of make: 1995 Table length: 4.000 mm Table width: 1.000 mm X: 4.000 mm Y: 1.000 mm Z: 1.500 mm Spindle taper: ISO50 Speed: 3.000 RPM Huron milling head Motor: 22 kW Machine dimensions (lxwxh): 10.000 x 6.000 x 4.250 mm Machine weight: 25.000 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Counter holder, counter bearing, bearing block, pillow block bearing, bearing for milling machine -Swallowtail: 102 by 126 mm by 20 mm high -Drawing: in the photos -Number: 1x counter bearing available -Price: per piece -Dimensions: 180/70/H140 mm -Weight: 6.9 kg

BÜHLER Stone Mill MSUA 400 4 kw V-belt drive n=500 rpm Inlet 100 mm diameter Engine rebuildt Bearing: oil exchanged

roll diameter: 400 mm roll length: 1000 mm rolls drilled: Kernbohrung Nip adjustment: hydraulisch 0 total power requirement: 45 kW Condition: used, overhauled Specification: Rolling mill 400 x 1000 mm - second-hand monobloc model, motor under the rolls - roll diameter: 400 mm - roll length: 1000 mm - rolls: with core bore, with central chamber for water cooling - Rollers mounted on bronze bushes with oil circulation lubrication via pump, - equipped with new slewing rings for connection to the water circuit - Gap adjustment: hydraulic, NEW - Hydraulic unit NEW - Tiltable guide plates - stainless steel roller container to hold the mixture - bi-directional rods - safety brake for NOT stop - AC motor: 45 kW - 400 Volt - 50 Hz - Painting: in RAL colours according to customer requirements - new control panel with touch pan ...

roll diameter: 560 mm roll length: 1500 mm rolls drilled: Peripher Nip adjustment: hyraulisch 0 total power requirement: 150 kW Condition: used, completely overhauled, with warranty Specification: rolling mill 560 x 1500 mm - used model external gearbox - motor sideways placed at the machine - roll diameter: 560 mm - roll length: 1500 mm - model: Duplocom / pluridrive - Peripherally drilled rollers for water cooling - Cardan joints between gearbox and rollers - Individual drive for the rollers, for variable friction - hydr. gap adjustment - Hydraulic unit - Tilting steel guide plates - rollers mounted on roller bearings with appropriate lubrication - rollers with new ball bearing slewing rings, make Maier, for the connection to the water circuit - One gearbox - two individual drives, each with: 2x 75 kW - 400 V - 50 Hz - two new frequency conv ...

X-axis: 13,000 mm Y-axis: 4,500 mm Z-axis: 1,000 mm Distance between stand: 6,500 mm C-axis: 190º A-axis: 110º Rapid speed XYZ: 15,000 mm/min. Rapid response AC: 10 tpm CNC control: Siemens 840D Spindle mounting: HSK A63 Spindle speeds: 30,000 rpm. Spindle power: 20 kW Tool changer: 20 positions Torrestool tables: 16 pieces X-axis: 11,500 mm Y-axis: 3,500 mm Z-axis: 750 mm Country of origin Spain Machine dimensions LxWxH: 19,000 x 11,000 x 6770 mm Machine weight: 70,000 kg

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 315 by 255 mm 40 mm high -Drawing: in the photos -Number: 2x counter bearings available -Price: per piece -Dimensions: 560/200/H285 mm -Weight: 20 kg

Counter support, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 265 by 215 mm, 30 mm high -Drawing: in the photos -Number: 2x counter bearings available -Price: per piece -Dimensions: 390/130/H260 mm -Weight: 30 kg

M. No.: 0392 Equipment / Additional information: Feeding width (mm): 500 Kw: 7.5 A: 380

Corundum disc mill Manufacturer: Fryma Type: MK-95/R No.: 215747 Year of construction: 1987 Power: 3.3 kW in EEx protection new grinding disc, with spare discs with hopper mounted on a mobile wagon LBH: 800 x 600 x 1720 mm

Buhler DMWP flake mill, 1000x600, complete with electric motor

Counter support, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 275 by 220 mm, 40 mm high -Drawing: in the photos -Quantity: 1x counter bearing available -Price: per piece -Dimensions: 450/110/H300 mm -Weight: 12 kg

Bead Mill Manufacturer: Fryma Type: MS-18 No.: M17118 Year of construction: 1996 Power: 11.43 kW Pressure product space: 2.5 bar Pressure double jacket: 2 bar with double-acting mechanical seal with blocking pressure station Grinding chamber as good as new LBH: 1200 x 800 x 1600 mm

Friedrich Deckel FP 2 LB tool milling machine This universal milling machine FP 2 LB from the well-known German manufacturer Friedrich Deckel in Munich has as a special feature an extremely stable basic body and is designed as a travel column machine i.e. the machine does not lose accuracy should heavy parts (up to 1000 kg) be clamped. Another special feature is the so-called inclined bed of 45 degrees. Thus, after dismantling the universal table, it is possible, especially V-engine blocks with 90-degree cylinder angle (e.B. amerik. V8) directly clamp and process. The long travel distance of 800mm is also an advantage in this case. Lid FP 2 LB universal swivel/tilt table (± 45° / ± 15°) Lid Universal Divider Vice 160 mm Working range: X= 800 mm / Y= 300 mm / Z= 400 mm From 01.07.21 the machines are ready for collection. Dismantling and transport by the buyer.  ...

Composed of: - Pin mill, manufacturer : Condux, type CST 150 / F, pin disc diameter : 165 mm; - Dosage - Filters - Container approach --> mill housing in stainless steel;

Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -1x motor: 0.15 kW 11160 rpm at 200 Hz -Voltage: 133 volts -Receiving shaft: Ø 15 mm -Tool: Ø 160 x 3.5 mm -Dimensions: 200/85/H70 mm -Weight: 2.5 kg

CNC Bedmilling Machine Make: SACHMAN Model: RP 3 x 1800 mm Year: 1996 ( only 5000 hours ) Control: Heidenhain TNC 407 Table: 2000 x 750 mm Speeds: 22 - 3500 rpm Motor: 15 kW Oil cooled universal TVK millinghead

fully functioning used 3 axis milling machine, brand lid, type FP2, with vice, and many accessories.

Tool holder, milling holder, milling tool -Number: 8x SK40 holders -1x: Tapping chuck, compensating chuck -35: Mount MK2, compensating chuck -suitable for: tool changer -Sale: only complete -Weight: 58 kg

Hosokawa Powderplex Sifier Mill APP 400 Crushing and sighting Drive power 37 kW Engine speed 3000 1/min Pressure shock resistant up to 10 bar-Ü additional view terrad Very good ready-to-use condition, directly from production!

Drawer cabinet, tool cabinet, steel cabinet, workshop cabinet -Drawers: 2 -Storage: 1 -Brackets for: SK40/SK50 milling holders -Dimensions: 660/1030/H1200 mm -Weight: 190 kg

USED BACHILLER STAINLESS STEEL BEATERS MILL REF.: C4750 Beater mill with a mobile disk with hard wear resistant steel plates. It can be used by two edges, against a static track. It is considered a cold mill because of the high air flow it generates.

Inlet: 450 x 580 mm Rotor width: 600 mm Rotor diameter: 450 mm Rotor blades: 3 Stator knives: 2 Motor: 55 kW

Tool holder, milling tool holder -Recording: SK50 -Recording tool: MK4 -Drill chucks: Surface clamping chucks, reducing sleeves, cutter heads, end mills, spindle tools -suitable for tool changers -Number: 6 recordings available -Price: per piece -Dimensions: 240/95/H95 mm -Weight: 3.0 kg/piece