129,240 used machines on RESALE, but how to find them? Machine Search
Pneumatic multi function press Operating pressure 6-8 bar Weight 106 kg dimensions 0.70 x 0.38 x 1.05 m Comments: Multi function punch air consumption 18 l per stroke, pneumatic punching operation via foot switch tripping
Total height 1500 mm Total length 3000 mm 5 pneumatic cylinders Compressed air pressure 8 bar Travel of pneumatic cylinders 100 mm Diameter of pneumatic cylinders 100 mm
L 45 Kw POWER 680 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw
Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request
Table 1750 x 920 mm, fixed stroke 101 mm, see pictures and description,; All right
L 30 Kw POWER 450 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 30 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw
Tech. Data Nominal press force 1000 kN at maximum stroke adjustment - commute 6.5 mm 1250 kN at maximum stroke adjustment - commute 3.5 mm Strokes with endurance 125/83/63 Hube/min Usable stroke rate 50 50 38 / min. Throat depth 320 mm, clamp 380 mm Stroke adjustment 10-120 mm, Stosselverstellung 80 mm Stosselflaeche 800 x 320 mm, recording journal 50 / 85 Tabletop table top hole, 900 x 630 mm 230 mm, Durchfalloch in the table 300 / 400 x 250 mm Drive - 7,5 / 5,5 kW Bulk 1350 x 2080 x 2780 mm, Btto 8900 kg
SINO NCP 160 eccentric press built in China in 2018 by Sino Machinery & Tools (Dongguan) Co., LTD. performs machining of metal workpieces with a press force of 160 tonnes. The machine is equipped with high-quality components, including e.g. a 100 mm adjustable slider making up to 25 to 55 strokes per minute, and a YU JAIV PDH-120 indicator displaying the distance of the die between the table and the slider. The large working area, ease of operation and outstanding precision, guarantee excellent machining results. The press offers the possibility of combining it with an automatic feeding system in order to increase the number of parts produced and significantly reduce costs. The total weight of the machine is 13 tonnes. Technical data of the SINO NCP 160 press - maximum press force: 160 t - work area dimensions (L x W x H): 910 x 600 x 410 mm - bolster dimensions (L x W x H): 125 ...
Briquetting press MATEC F-Cube 20 new Dimension press LxWxH: 130x74x112 cm weight 233 kg Briquette square 30x30 mm Capacity approx. 10-25 kg briquettes / hour Size feed funnel approx. 0.33 m3 Motor hydraulic pump 2.2 kW, 3x 400 V, 50 Hz Electricity consumption approx. 1.1 kWh How we work Continuous operation Year of construction 2021 Additional options: - Extension line for briquettes with stand -Auto. Start-stop system for operation with level monitoring - Sensors for level monitoring - Hydraulic oil 30 liters - 3 m cable with Euro plug 16 A - Flange adjustment filter-hopper press The spec. Density of briquettes is about 900 kg / m3. The maximum wood moisture content is 15%. The measured noise level is 62 dB. New machine, ready for operation. Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden ...
various hand spindle presses small More: Foot pendulum press Jantsch
Frame press Hess economic hydraulic 3600 x 2250 mm L x W x H: 400 x 100 x 270 cm Weight approx. 1100 kg year 1987 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw
Dear customers, currently we offer a polystyrene press incl. shredder for sale. It is a new machine that has 0 operating hours! Here are a few more technical details: Material to be processed: EPS moulded parts and chips Maximum material density that can be processed: 18 kg/m³ Loading opening: 700 x 360 mm Filling height 1,402 mm Achievable compaction: up to 250 Kg/m³ System throughput: up to 15 kg/h Block dimensions: 130 x 130 mm Power supply: 3x400 VAC+N+PE 50 Hz Connected load: 1.5 KW, 400V 50Hz incl. automatic press pressure regulation with pellet holder Finish: RAL 7035 (light grey) combined with RAL 2011 (deep orange) Incl. water dosing system for direct screw cooling up to 10 litres/h with water shut-off valve. Price plus VAT, which will be shown separately on the invoice. Transport possible worldwide for an extra charge! If you have any questions, please d ...
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
Transfer press KRUPP PST-A 160 built in 1980. Technical data of the KRUPP PST-A 160 press: - nominal pressure: 160 tons - cutting force grade 1: 400 KN - force between stands: 1200 KN - number of working steps including cutting stage: 11 - distance between stands: 200 mm - slider stroke: 210 mm - drawing depth: 70 mm - range of jumps, infinitely adjustable: 15-75 / min. - production range of jumps with repeatability of its setting: 25-75 / min. - number of actuation movements: 15-25 / min. - a usable work resource for a jump in the range of 25-75 strokes per minute. : 20,000 J - maximum load on a single step: 500 KN - maximum load of a single step using inserts: 630 KN - maximum width of the tape: approx. 340 mm - maximum diameter of the cut: 120 mm - minimum diameter of the pattern: 30 mm - distance between stands: 2450 mm - height of tool building at the lower posi ...
l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw
CNC – controlled frame gluing press for automatic gluing of all frame constructions with dowel connection – tine connection – 45° miter connection, automatic centering of the press plates and the upper press beam. The frame presses are available in the following sizes – pressing area 3,000 x 1,700 mm – 3,000 x 2,000 mm and 3,500 x 2,500 mm. Two vertical press cylinders – pressing force per cylinder 7 tons (optional four vertical press cylinders). Two horizontal press cylinders, stroke range 150 mm - pressing force per cylinder 3 tons. Maximum tread depth 130 mm (larger tread depths on request). CNC control from SIEMENS® with touch screen for calling up three automatic pressing cycles, 99 compression programs can be stored per pressing cycle. Among other things, the following parameters can be programmed: frame size, frame profile structure, pressing time, pr ...
Technical data: -Compressive force 100 t -Throat 320 mm -Wide stand below the Guide 400 mm -Table size approx. 850 x 610 mm -Discontinued diarrhea hole in the table 335 / 300 mm -thickness of the table clamping plate 90 mm -gr. Height approx. 300 mm -Plunger area 600 x 335 mm -Adjustable height of the RAM 80 mm -Stroke adjustment 10-130 mm -Emissions er hub in the RAM 32 mm -Speed continuous operation approx. 56 / min -Drive 400 V / 11 kW -Space requirement approx. B H 1900 x 2800 X 2200 mm -Weight approx. 9000 kg Starring:-UVV press backup controller PREVENTA -Hydr. + pneumatically actuated clutch -LUTEX auxiliary braking system -Central lubrication
Hi, I offer you Hydraulic power pack-three engines 90 KW each -oil tank 4500l, -Each engine drives two hydraulic pump gear -Pump Model 45V60A Power supply power to the extruder scrap shears in the set are three Dimensions chydrauliczne 160x190 coolers coolers 3 x -cooling connection 100 mm -power connection 80 mm Very Good Condition Net price: 59900 $-€14000 contact: + 48 600-517-834
Gluing stand VHS with motor hydraulics for gluing all frame constructions with dowel connection – tine connection – 45° miter connection. The motor-hydraulic gluing stands VHS are available in the following sizes: Maximum grouting range 2,500 x 1,800 mm 2,500 x 2,100 mm 3,000 x 1,800 mm 3,000 x 2,100 mm 3,500 x 2,100 mm Three vertical press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each. Two horizontal press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each (optionally, the gluing stands can of course be supplied with more press cylinders). Drive power 0.75 to 1.25 kW.
Pressure capacity: 8000 kg Maximum cutting area - 200 mm2 for material strength 40 kg / mm2 Horizontal radius 200 mm Clearance between the side walls 160 mm Fixed hub 35 mm Pin hole in the Stossel 38 x 60 mm Adjustability of the Stossels 70 mm Weight of 400 kg of the Presse Operating instructions The machine is located in the new value. State, probably never in use. Control actuator Stober
Roll press / dough dividing and warp knitting machine / Klievmaschine Machine Mechanics completely overhauled & repainted by the expert New installation of the entire electrical system, according to the latest standards 6 months warranty Properties: + Stationary machine, very robust & stable construction + Machine is set in motion by switch-on lever, one-hand operation + Cleaning position electric, to the rear, with switch + even division of the dough, excellent rounding of the dough pieces + equipped with active cut-off, for square dough pieces + Partial knife / cutter head has been overhauled / recoated + completely disassembled, mechanically overhauled, repainted + New installation of the entire electrical system, according to the latest standards + Transmission parts run constantly in an oil bath + complete overhaul in Babenhausen, according to German quality stand ...
Universal - NPR-55U Stanze Knee lever punch -Punching of paper, cardboard and plastics. -for simple stamping -The cutting blades can be recorded from the shaft -The cutting blades can be created also not attached just under the pressure plate. -The pictured tools are not part of the offer.
used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 30 S Year of construction: 2009 Serial No.: 109138 specifications: Pressing force: 30 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Height from the ground: 1,310 mm Bale size: 1,200 x 800 x 800 - 1,100 mm Bale weight: up to 270 - 360 kg Drive power: 7.5 kW Cycle time: approx. 29 sec. Pressing time: approx. 14 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)
AUTOMATIC BRIQUETTING machine type COMAFER DINAMIC 85N second hand machine volt. 380/50 CE mark : Yes briquett diameter mm. 60 production from 40 kg. to 85 kg. / hour motor power Hp 7,5 net weigth kgs. 850
Hydraulic glue press with heating base, infinitely variable temperature setting, stuffenlose setting of the adhesive holding time, Power: 5 kW, 380 v 50 Hz; Two-hand operation.
• 120 tons total pressing force • Pressing area 3,000 x 1,350 mm • With patented, thermostable electric heating plates with automatic temperature control system • Connected load of the heating plates with economy circuit 10.6 kW • Connected load of the hydraulics 2.2 kW • in 6-cylinder version Ø 85 mm • Lockable main switch • Push-button control • Stop button • Safety ripcord, safety edge • Timer with automatic opening and acoustic signal • Stroke = opening 400 mm • Infinitely adjustable stroke limitation • 2-stage hydraulics with automatic pressure follow-up • Compact hydraulic power unit mounted maintenance-free in the oil tank • Teflon bronze guides in the cylinders • Hard chrome-plated steel pistons • Heavy rack and pinion compensation for synchronous table movement • fully open on four sides • Economy circuit installed as s ...
Automatic baler Manufacturer: HSM Type: VK 4012 Year of construction: 2005 specifications: pressing force: 45 t Channel format: 720 x 900 mm (W x H) Setting: 4 x horizontal Filler: 1.000 x 650 mm Power: 22 kW with Superchargers Throughput capacity at 40 kg/m³ bulk density: maximum approx. 12.8 t/h Bale dimensions: approx. 720 x 900 x length (600-1.200) mm including funnel in special execution for the purpose of manual loading
Baling press cardboard foil MF100 | 6 t pressing force The MF100 balers are ideal for pressing cardboard, paper, film, clothing and other materials. Volume reduction through compaction of up to 90%. The press is user-friendly with a large filling volume. The automatic bale ejector helps to remove the bales from the baler without any problems. Characteristics: Bale weight of up to 100kg Ideal for use with medium material volumes Fully automatic bale ejection Powerful cylinder for uniform material compaction Hold-down device to reduce material springback CE certified Made in Europe Specifications: Pressing force: 6 t Motor: 1.5 kW 13 Amp Power supply: 220-230 V (1 phase) Machine dimensions (H x W x D): 2371 x 1388 x 1046 mm Transport height: 1876 mm Machine weight: 632 kg Cycle time: 28 seconds Noise level: 65 decibels Bale: Ba ...
EinspannmaÃ?e: 1600 mm x b: 2900 mm frame: 1600 mm x b: 2600 mm â?¢ Pression-Druck by 1T, self-locking, 140 mm â?¢ Versatility - many applications (frame, body, surface gluing) â?¢ Workload - ergonomic posture â?¢ Save time with user-friendly operation â?¢ Frame are bolted and therefore can be disassembled â?¢ Pressing units galvanized G & FE-RPW-3000PL
SPK KB 2132 eccentric press was manufactured in the USSR in 1980. Operating with a force of 160 tonnes, the press of almost indestructible design offers the highest quality and precision during the most demanding workpiece machining. The machine’s equipment includes among others a pneumatic clutch, a large-area slider performing up to 71 strokes per minute, central lubrication and manual control. The total weight of the press is 13200 kg. Technical data of the SPK KB 2132 press - maximum press force: 160 t - work table dimensions (L x W): 1000 x 700 mm - maximum slider stroke: 160 mm - minimum slider stroke: 25 mm - slider dimensions (L x W): 580 x 460 mm - slider adjustment range: 120 mm - slider stroke rate: 71/min - intermediate plate thickness: 110 mm - distance between work table and slider (slider in lower position, largest stroke, connector unscrewed): 480 mm - bore ...
TECHNICAL SPECIFICATIONS Manufacturer: HENKE Designation: Production plant for concrete block slabs Type: UNI 2000 Year of construction: 1995 Operating hours: 11,543 h COMPOSED OF: Item 010) Fully automatic rotary table top pressure press UNI 2000/600/7 Item 020) Attachment distribution device for fine-grained attachments Pos. 030) Fully automatic dividing disc dosing unit with 8-fold ejection Item 040) Fully automatic direct washout system "WESER 100/2" for flat laying (horizontal) Item 050) Moulding frame device 400 x 400 mm, 2-fold Pos. 070) 2 x chain conveyor 1.50 m long Item 080/120) Pallet destacker Item 090) Cleaning brush Item 100) Pallet oil roller Item 110) Intermediate transport Pos. 130) Plate removal device Item 160) Stacking arm with bearing block Item 170) Chain conveyor 5 m long Pos. 180) 2 x Plate Pack - Lifting Item 190) Parcel push-off device ...
Hand spindle press to push pins in printed circuit boards 2 presses on a plate, with a dial indicator.
JJZ-CP type press designed for the production of plywood, doors, MDF. The glued elements are fed and removed from the press automatically by means of driven rollers. The press can be used with glue feeders. Specifications: -max. pressure 500T/ adjustable/ -max. load height 1300mm -max. batch size 1300x2500 -press size 3600x1370x4500 mm -press foundation ~500 mm below the floor level -feeding table 2000x1960 mm -receiving table 2350x2500 mm -max. power 13.2 kW -Ce -capacity of 6 batches per hour Currently, we glue panel doors and MDF board on presses. Very good technical condition. We offer a plywood production line dedicated to these presses.
Make: Engel Type: Vertical Rubber Injection Model: ES 280V/40VT-ELAST Serial number: 41938, Year of manufacture: 2000 Clamping force 400kN Injection volume 280cm3 Platen size: 860x400mm In good condition.
sed Manesty Rotapress MK IIA rotary tablet press, 45 station, double sided, with pre-compression, keyed upper punches, With feed hoppers, force feeders, controls and associated parts.
THE WOOD PRESS FOR HIGH-QUALITY FUELS The RUF LIGNUM Classic wood briquette press is ideal for briquetting medium quantities of wood chips that accumulate in the woodworking industry. The briquetting process can generate additional revenue and reduce storage and transport costs. Another advantage is the flexibility of our wood briquette presses. You can press different material grains into high-quality briquettes without the need for a binder. As a result, RUF briquettes have a higher utility value and an optimal CO2 balance as a valuable energy source. Our LIGNUM series also impresses with high energy efficiency and low wear thanks to the innovative RUF hydraulics. YOUR BENEFITS AT A GLANCE - Fully automated 24-hour operation possible -Longevity - Low maintenance costs - Compact design - Direct integration into existing production facilities possible Bto8iej998 - Experience f ...
BRIQUETTING WOOD CHIPS AND GENERATING ADDITIONAL REVENUE With our RUF LIGNUM R4 wood briquetting press, you can process medium to large quantities of wood chips, regardless of the type of wood, into high-quality briquettes in the best possible way – without the use of binders. Through the process of briquetting, you achieve higher revenues and at the same time reduce transport and storage costs. Our robust wood briquetting presses of the LIGNUM series impress with a long service life, low wear and can be integrated directly into existing production systems. The innovative RUF hydraulics also ensure high energy efficiency. YOUR BENEFITS AT A GLANCE - Fully automated 24-hour operation possible - Durability & low wear - Low maintenance costs - Compact design - High energy efficiency - Experience for over 35 years ADVANTAGES OF RUF BRIQUETTES - Additional revenue for briquett ...
PRESS FOR PRODUCTION ALUMINIUM TRAYS FOR ALIMENTARY USE COMPLETE WITH DOUBLE IMPRESSION MOULD-1100 CC. COMPOSED OF: A LUBRICATION UNIT 4-COLUMN MOLDING UNIT TOW-SCRAP CONTROL PANEL. 55 STROKES/MINUTE DEPENDING ON THE MOULDS. PASS COLUMNS FOR MOULDS UP TO 800 MM
Lefort / Corema lid press P400 TE for bale size 400x400 mm, press box 3 m length, opened 1.2 m wide, each wing 90 t and final compressor 100 t pressing force. Drive 30 kW Rexroth pump.
automatic baler Manufacturer: PRESONA Type: LP 65 VH 2 Year of construction: 2012 specifications: Press force: 65 t Specific pressing force: 7.87 kg/cm² Drive power: 45 kW Throughput: 370 m³/h Filling opening: 1,500 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 425-575 kg Setting: 5-fold vertical Oil tank: approx. 1,000 ltr. capacity Machine weight: approx. 26 t Optionally with chain conveyor belt Manufacturer: BLUETECH Type: Chain Conveyor Belt Year of construction: 2012 Specifications: Conveyor width: approx. 1,500 mm Feed length: approx. 5,000 mm Climbing length: approx. 10,500 mm according to attached pictures
Number of punch stations 35 , output tablets 210,000/h , max. tablet diameter 13 mm , max. filling depth 18 mm , max. tablet thickness 8,5 mm , max. compression force 100 kN , max. initial compression force 20 kN , dieplate speed 15-100 rpm .
McIntyre M20 Can / Metals Baler Protect the environment and generate income by baling aluminium and steel cans. Versatile The M20 Baler is not only a cost effective system for cans but can also be used for many other applications where automatic volume reduction or product destruction is required. The M20 Baler will accept cans up to 250mm x 480mm and will produce up to 500kg of 20g aluminium drink cans per hour. The smaller the size of the can, the greater the machine output. When fed with aluminium drinks cans, the M20 crushes and locks the material together to produce dense 274mm cubes, weighing approximately 9- 11kgs. Such dense bales means that no tying or strapping is needed. The cubes are simply ejected from the machine and ready for transportation. Optinally, you can buy it, with can sorter!
Rotative tablet press of 27 stations Max. diameter of the tablet 16 mm Filling depth 18 mm Pressing capacity 80 Kn Prepressing capacity 20 Kn Production from 48.000 to 100.000 h Dimensions : 1.000 x 950 x 1876 . Weigh 1850 Kg. Force feeder Type of tool : B
McIntyre Drum Crushers McIntyre fully automatic drum crushers are able to reduce 45 gallon (205 litre) drums down to discs with a thickness of only 100mm (4”), saving you space and cutting your transport and disposal costs. Choice of machine Two models are available, able to process all drum types, sealed or topless, up to 45 gallons (205 litres). Both machines are fully automatic and can be adapted to handle smaller drums or tins. The main difference between the two models is the speed at which they operate. The high-speed version has been designed for the processor with a large quantity of drums, and will handle up to 100 x 45 gallon (205 litre) drums every hour. This machine also comes with a separate portable power pack, which can easily be connected to other hydraulic equipment. The standard machine is designed specifically for the customer with only a limited amount of drum ...
maximum number of results exceeded
please refine your search
