126,614 used machines on RESALE, but how to find them? Machine Search
Specifications: Capacity 50 tons Stroke rates 115 rpm Projection 250 mm Plunger stroke 8 - 120 mm Plunger adjustment approx. 70 mm Table , WxD approx. 650 x 500 mm Diarrhoea och approx. 250 x 180 mm
Maximum force: 1600 tons Slider stroke length: 400 mm Unattainable-course: 12 mm Number of courses of a slider per minute: 16 Number of single turn-on: 12 The closed height: 870 mm Adjustment: 220 mm Under-forginig plate: -From left to right: 1600 mm -From front to rear: 1600 mm -Thickness: 650 mm Slider overall dimensions: 1600x1600 mm Aperture in a table: 1000x1000 mm window dimensions in cheeks: 1650x1650 mm Course of a rigid pusher in a slider: 100 mm Force of a rigid pusher in a slider ton-force: 80 Main electric motor power: 110 kW Course of pneumatic pillow: 160 mm Force of pushing out of a pneumatic pillow ton-force: 71 Hydropneumatic pillow: -Working course: 250 mm -Force of pushing out ton-force: 25 -Force of a clip ton-force: 250 Press overall dimensions: 4670x4670x8110 mm Press weight: 147 tons
automatic baler Manufacturer: WELGER Type: SB 2000L Machine No.: 1307 51 321 specifications: Pressing force: 7 t Drive power: 11 kW Bale format 500 x 400 x length in mm Machine weight: approx. 1.9 t
pressure:6,3 t throat:170/180 mm stroke:310 mm power capacity:3 kW dayligth:775 mm weight of the machine ca.:1,5 t clamping table:470 x 330 mm table height over floor:800 mm C-Type 1 Station
HOT PRESS model SIMI 4LP second hand machine plates useful size mm. 2500 x 1300 n.04 pistons diam.mm. 80 max. thrust Ton. 60 specific pressure max. kg.2 / cm2 opening mm. 320 hot water plates heating via wood boiler (optional) weight kgs. 3000
Bale size (W x H) approx. 1,100 x 700 mm Bale weight approx550kg
pressure:2 t dayligth:80 mm Center of spindle to wall or column:100 mm weight of the machine ca.:0,5 t dimensions of the machine ca.:0,8 x 0,6 x 2,0 m Hand operated fly press, with center turning device appr. 100 x 400 mm length - Handwheel diameter 600 mm
press capacity:950 kN control:Siemens S7 Required air-pressure:6 bar loading area:1200 x 600 mm Pressure power:1000 kN total power requirement:18 kW weight of the machine ca.:6200 kg dimensions of the machine ca.:2600 x 1300 x 3100 mm
Key data: 15 t, 66 mm
Burger Press D07 Length 1.20 m Width 0.60 m Height 1.70 m 2 Hand control Switch to foot control 1 press die
Specifications: Capacity 300 to Stroke rate 35 strokes Plunger width 1000 mm Projection 450 mm Plunger stroke 20 - 140 mm Plunger adjustment 80 mm Engine power 30 hp Weight roughly estimated 18 tons
pressure:10 t distance between columns:450 mm :1500 mm table-size:450 x 400 mm weight of the machine ca.:470 kg dimensions of the machine ca.:1400 x 750 x 1600 mm
pressure:10 t stroke:400 mm total power requirement:1,6 kW weight of the machine ca.:1,1 t dimensions of the machine ca.:1100 x650 x 2050 mm dayligth:500 mm table-size:400 x 450 mm Documents:vorhanden
pressure:160 t throat:360 mm stroke:500 mm total power requirement:17 kW weight of the machine ca.:7,2 t dimensions of the machine ca.:2,0 x 0,95 x 3,70 m table-size:900 x 630 mm Documents:vorhanden
Used multi-layer paver Zenit 844 Built in 1993 inclusive: 1 piece concrete mixer 750 l Teka 1 piece concrete mixer 500 l approx. 12 pieces of used moulds approx. 100 production pallets Used concrete multilayer machine Manufacturer: Zenith Type: 844 Year: 1993 including: - 1 pcs 750 liter mixer Teka - 1 pcs 500 liter blender - about 12 moulds - about 100 pcs production boards
pressure:160 t throat:360 mm stroke:500 mm Documents:vorhanden
pressure:20 t Stroke:230 mm table surface area:Ø600 mm distance table - lower edge of ram:770 mm weight:595 kg
weight of the machine ca.:620 kg dimensions of the machine ca.:1000 x 920 x 1550 mm
Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
Pressure:175 t chamfer lenght:4100 mm distance between columns:3600 mm column arm:410 mm ram stroke speed:180 mm/sec return speed:135 mm/sec working speed:10 mm/sec work stroke:275 mm oil volume:200 l dayligth:550 mm table height:900 mm table width:90 mm total power requirement:15 kW weight of the machine ca.:12000 kg dimensions of the machine ca.:5100 x 2150 x 2850 mm
nominal force:100 t stroke:320 mm no. of strokes:35 /min distance between columns:360 / 250 mm Distance table/ram, max. stroke up, adjustment up:500 mm table surface area:320 x 450 mm table height over floor:660 mm ram surface:250 x 280 mm spindle diameter:125 mm power capacity:3,0 kW weight:4,5 t Dimensions (WxDxH):2,0 x 1,6 x 3,1 m
pressure:60 t distance between columns:650 mm stroke:220 mm distance table/ram, max. stroke up, adjustment up:410 mm table surface area:600 x 525 mm hole in the table:110 mm table height over floor:900 mm side window:200 mm ram surface:560 x 490 mm power requirement:15,0 kW dimensions (WxDxH):1,9 x 1,3 x 2,7 m foundation pit:not necessary
VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available
pressure:250 t distance between columns:1110 mm stroke:250 mm Distance table/ram, max. stroke up, adjustment up:500 mm Table surface area:1100 x 900 mm Table height above floor:950 mm Side window:690 mm Ram surface:1100 x 900 mm Oil volume:730 l Power capacity:56,0 kW Dimensions (WxDxH):2,3 x 1,55 x 3,96 m
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
nominal force:160 t stroke:140 mm no. of strokes:85 /min distance between columns:400 mm distance table/ram, max. stroke up, adjustment up:500 mm table surface area:400 x 450 mm table height over floor:800 mm Allowed max. force:230 t ram surface:400 x 320 mm spindle diameter:125 mm power requirement:7,35 kW weight:5,0 t dimensions (WxDxH):1,7 x 1,2 x 2,9 m
pressure:300 t distance between columns:1800 mm stroke:1000 mm Distance table/ram, max. stroke up, adjustment up:1300 mm Table surface area:1600 x 1200 mm Table height above floor:1080 mm Ram surface:1600 x 1200 mm Weight:24,0 t Dimensions (WxDxH):2,8 x 2,1 x 6,0 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2
no. of strokes:150 /min impact energy:420 kJ distance lower die block / ram gudeway:435 mm Throat:425 mm steel forging - rectangular up to:110 mm steel forging - diameter up to:125 mm power requirement:22,0 kW weight of hammer:3,9 t weight of anvil:3,0 t ram hammer weight:200 kg weight:6,9 t dimensions (WxDxH):1,1 x 2,3 x 2,4 m
Machine number: 3-0512 Compressive force: 28 kN Stroke: 60 Table dimensions: approx. 200 x 160 mm incl. installed punching tool
Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused
equipped with manual crowning and 1 set of flatbed tools; Recently equipped with new control and laser security
Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W
Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W
Machine number: H74/247 Press force: 4 Mp Oil pressure: max. 200 atm Motor power: 1.1 kW Table dimensions: approx. 250 x 250 mm
Compressive force: 28 kN Stroke: 12 mm Safety distance: 100 mm Run-time travel: 0.06 s Table dimensions: approx. 200 x 160 mm with pneumatic punching tool mounted
SINGLE POINT OPEN BACK INCLINABLE POWER PRESS Inv. No. 11.421PC Make IWK Model PEKRON 150Z Machine No. 1512 Capacity 150 tons Ram stroke 200 mm Ram adjustment 100 mm Shut height min/max 370 / 570 mm Strokes per minute 40 Knock out in ram 0 – 70 mm RPM 10 - 815 Throat 290 mm Power inclinable 30 degrees, 4kW Table 1000 x 630 mm Ram 760 x 410 mm Q 12 Volts 230 / 400 Cycles 50 Hz Including: Bolster plate 1.000 x 630 x 80 mm Bolster plate 1.000 x 630 x 90 mm Table opening, diameter 440 mm Updated electrics 2004 CE certified
Gluing Press / Press Rotor / Gluing Stars For the production of solid wood panels or similar Manufacturer: ACMA Levels: 4 Hydraulic Cylinders: 6 per level Hold-down: 2 frames per level Working area per level approx. 2900 x 1150 mm
SECOND HAND BENDING PRESS - plates dimensions mm. 3100X800 - opening mm. 800 - 8 cyl. diam. 80 mm.
V6 30 degree T mold set; length approx. 3.1 meters
Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused
maximum number of results exceeded
please refine your search
250 € 
