atlas copco ga used for sale

MWM TCG 2016 V 16 Exchange motor / short block with cylinder heads (biogas) Bücker + Essing short block with cylinder heads - crankcase in Exchange (tested according to manufacturer's specifications and repaired) - crankshaft in Exchange including new storage (tested according to manufacturer's specifications and repaired) - piston Squisch new -Liners with Coke wiper ring new -Connecting rods in Exchange including new storage (tested according to manufacturer's specifications and repaired) - cylinder heads in Exchange (tested according to manufacturer specifications and repaired) -Wheel drive including timing chest cover -Oil pump new including oil suction pipe -Oil pan -Oil cooler bundle (new) oil filter (new), closed oil circuit -Camshaft new incl. storage -Torsional vibration damper new -Flywheel housing and flywheel -including paint (RAL 5010) The here offered motor is ...

FOR SALE... OVERHAULED TURBOCHARGERS ABB VTR 254-11 & BBC VTR 214-11 TO WHOM IT MAY CONCERN; WE VE BELOW LISTED OVERHAULED & REPORTED TURBO CHARGERS AT OUR STOCK. READY TO TRANSPORT AND USE... ABB VTR 254-11 HZTL 428765P2 nNmax 523 nBmax 497 tMmax 680 C tBmax-650 C SFUSO1 YEAR OF BUILT 2010 MADE IN SWITZEWRLAND BBC VTR 214-11 NoHT 399285 their 635 Tmax 680 V 01113 R 012 H 04109 W 12206 E 03221 U 023 YEAR OF BUILT 2012 MADE IN SWITZERLAND IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CIONTACT WITH US. Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Gas filling device / scale with rolling landing Manufacturer: Ninnelt International GmbH Type: CTE 110 In good condition!

Gas filling facility with weighing technology / scale manufacturer: Ninnelt International GmbH Type: What 110 p In good condition!

Size max 480 x 320 mm Speed max 18,000 c / h Equipment 1 feeder 3681

Complete gas measuring station / gas detector device, including Dräger Polytron 2 IR Ex 334 etc. used Manufacturer: Dräger Type: Polytron 2 IR Ex 334 Condition: Used - top condition Price: The total price of the complete system is only 50% compared to the sum of the usual market prices of all assembled used parts. The complete gas measuring device is mounted on a mounting plate of a control cabinet and consists of: - Mounting plate 110 x 170 cm - Air suction pump - Gas measuring device Dräger Polytron 2 IR Ex 334 - Brooks variable area flow meter 1355 / D1D4A1Z5BA00 - Switching amplifier Pepperl u Fuchs KFD2-SR2-Ex1.W - 2 Pepperl u Fuchs KFD2-STC4-EX2 transmitter power supplies The air is sucked in by the pump and fed into the gas detector and measured. Function guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. Since we  ...

FOR SALE COMPLETE T/C ABB VTR 454-32 TO WHOM IT MAY CONCERN; WE ARE ABLE TO SUPPLY USED COMPLETE T/C ABB VTR 454-32 AT TURKEY PLS FIND SPECIFICATION T7C AT BELOW. TYPE VTR 454-32 HT 833511 N of Saad 290 Nbmax 276 t Saad 580 tbmax 550 YOB 2005 SWITZERLAND IF YOU'VE ANY QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

Qty. 1 Second-hand continuous galvanising line Mfc.: Koryo SanGi, WMS Co., Sumitomo, Dongyang GiGong, Myungshin Mach., Kanto TK, Hitachi, Yuyoung Industry, Cosmo Gas, Hankuk Yugong, Jungwon Mach., Bugong Ind., Hanhyung Industry, SeunJin Mach., Cheongsong Electrics, Jungbu Civil Gas, HK. ENG, Cosmo Construction, KyungJin Construction, Cheonsu Hwankyung Ind., Shinhyeung Built: 1983 Some revamp in 2005 Material: Cold Rolled mild steel FH Strip Width: 650 - 1.250 mm Thickness: 0.2 -1.6 mm Capacity: REF: 27 Ton / Zn 1.2 Ton = 1 Hour HMI Main Control Operation system Zn Coating Wf 80 gm – 220 gm (Both Side) Coil Out Diameter: 2.050 mm Line Speed Max: 150 m/min Entry Section: 195 m/min Process Section: Max. 150 m/min Exit Speed Max.: 195 m/min

CNC Router and 3D engraving machine T-Rex 0712: Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all axis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 17.000 mm/min Operating speed max. ca. 12.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table1650 x 880 mm Travels: X=1200mm; Y=700mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions  ...

Qty. 1 Second-hand continuous galvanising line Mfc.: POSCO Built: 1997 Capacity: approx. 100 000 per annum Strip width: 720 – 1250 mm Thickness: 0.2 – 1.6 mm De-Coiler ID 508 mm OD 2000 mm Weight: 20 Tons Finished product: Coil Strip width: 720-1250 mm Thickness: 0.2-1.6 mm ID 508 mm OD 1600 mm Weight: 10 Tons Sheet Strip width: 720-1250 mm Thickness: 0.2-1.6 mm Weight: 3 Tons Line speed Entry section: max. 150 m/min. Process section: max. 120 m/min. Exit section: Coiling max. 150 m/min. Shearing max. 100 m/min. Threading speed: 20 m/min. Coating method Both sides coating, Regular spangle Coating weight 120-500 g/m² based on both sides Post treatment Chromating Electricity High voltage 10 kV Low voltage 380 V AC, 3 ph., 50 Hz, 220 V AC, 1 ph. Water Pressure min. 3 kg/cm² Steam Pressure min. 5 kg/cm² Temperature min. 158 °C Production process Coil s ...

FOR SALE... 2 SET T/C TO TCR 18-42065 YOB 2010 AT TURKEY HAVE A GOOD DAY SIR. WE VE 2 SET COMPLETE T/C TO TCR 18 - 42065 AT OUR STOCK. PLS FIND TURBO CHARGER SPECT AT BELOW. TYPE: TCR 18 - 42065 WORK NO: 7642160 / 7642161 SPEED: 37300RPM T MAX: 650C. YOB: 2010 IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST of regards; Aliaga marine services E mail: info@aliagamarine

Full gate clamping cars Möhringer among the REF. No. 262-1492 L x W x H: 280 x 120 x 180 cm Weight 3000 kg Built in 1984 Price EXW with full frame saw Boegli MARA-2 (Ref. No. 262-1492) 19'800 EUR Excl. VAT The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

MWM TCG 2016 V 12 Exchange unit with complete motor and generator overhauled on basic frame Payment by invoice warranty Bücker & Essing GmbH assumes the warranty exclusively for the delivery volumes supplied by it. A warranty for damages that are not directly related to the delivered and performed thing, as well as a warranty for consequential damages, are expressly not assumed. The warranty is assumed for a further 12 months at the most or until 8000 operating hours have been reached after commissioning, whichever of the two cases occurs first. Regardless of the commissioning date, the maximum warranty period is 15 months after delivery. The warranty case must be notified immediately in writing. Warranty claims can only be asserted if the commissioning and maintenance have been carried out and documented in accordance with the manufacturer's regulations. Commissioni ...

MAN 2876 LE302 gas engine (biogas) 190KW (also as 210KW-Version) It's a replacement engine for various biogas CHP. Overhauled according to manufacturer guidelines and RAL quality seal(maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a quotation. We have other Exchange engines (2848 with 250KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers, etc. and other components and spare parts for MAN gas engines in stock.

MAN 2848 LE322 gas engine (biogas) 250KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

Further information on request

MAN 2842 LE322 gas engine (biogas) 370KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2848 250KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

HAVE A GOOD DAY SIR. WE VE NEW UNUSED. MITSUI MAN NA 57 TO 725 P IT STOWED AT FABRIQ WOODEN BOX. IT WILL NEVER MOUNTED AND USED. PLS FIND SPEC AT BELOW. READY TO TRANSPORT. EX STOCK. MITSUI MAN: NA 57 TO 725 P NO.: 2430 SPEC AD: 490 A4K : 404.3 REVOLUTION: 15000 RPM MAX TEMP: 600 C IF YOU'VE ANY FURTHER QUESTIONS PLS DO EMERGENCY HESITATE TO CONTACT WITH US. READY TO TRANSPORT. EX STOCK. Capt. Ayhan Ugurluba Best Regards ; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

Force of pressure: 100 t projection: 350 mm table size: 690 x 840 mm Durchfalloch in the table: 160 mm table adjustment: slide area: 450 x 600 mm slide adjustment: 80 mm stroke adjustment: 8-100 mm stroke rate: 60 / min drive motor: 380 V, 5.5 kW space: 1850 x 1850 x 2650 mm weight: 6800 kg

The ZAKMET FIRECUT CNC 1325 13000 X 2500 gas plasma cutter was produced in 2011. The machine is equipped with Hypertherm EDGE'Pro digital control. The burner's working area is 13,000 mm long and 2,500 mm wide. The running elements of the cutter are lubricated with the Memolub 3.0 central lubrication system. Technical data of the plasma burner: - machine working area (L x W x H): 13,000 x 2,500 mm (additionally 700 mm) x 200 mm - maximum table load: 15 kN / m2 - machine supply voltage: 3x400V AC 50 Hz - central lubrication: Memolub 3.0 - minimum temperature of the working environment: +5 degrees C - maximum temperature of the working environment: +60 degrees C - machine dimensions (L x W x H): 14500 x 5500 x 2000 mm Plasma cutter equipment: - CNC control: Hypertherm EdgePro - ventilated section table: 1550 x 2600 mm - 9 segments - gas burner: type MS 3452 \ 250-PM (x2) - ...

Cylinder head for MWM TBG 620, TCG 2020 needed, not overhauled. Can we get over on request. Quantity: On request. Please note: We have various other parts of from different manufacturers and types available.

10,000 pieces of grating gratings for pallet shelves galvanized Insertion grids available in different sizes, mesh widths, support rod and weight load: Negotiation price: from € 5,-- net per piece from stock Price with € 5,-- refers to the insert ingerate with the size 24.5 x 104.5 cm Larger quantities on request! Insertion grid Mesh width 80 x 89 cm 2.5 x 2.5 cm 99.5 x 49.5 cm 3 x 3 cm 99.5 x 99.5 cm 3.5 x 3.5 cm 100.5 x 98.5 cm 4.5 x 1.1 cm 104.5 x 24.5 cm 6.5 x 3 cm 108.5 x 111 cm 6.5 x 6.5 cm 120 x 89.5 cm 7 x 3.5 cm 120 x 109 cm 7 x 4.5 cm 125.5 x 59 cm 7 x 7 cm 128.5 x 81 cm 129 x 118 cm support rod 132.5 x 111 cm 20 mm x 2 mm 134 x 76.5 cm 25 mm x 2 mm 134 x 92 cm 30 mm x 2 mm 134.5 x 99.5 cm 35 mm x 2 mm 134.5 x 122 cm 40 mm x 2 mm 143.5 x 124 cm 45 mm x 2 mm 157.5 x 81 cm 170 x 150 cm 179 x 121 cm Used goods, very good condition, see  ...

Horiba Here we offer you a Horiba exhaust system Mexa 7100D. Including JAG-10-000-061 bottle trolley approx. 1200 x 1064 x 802 mm and OVN-724A Stationary exhaust gas measurement before/after exhaust gas aftertreatment, Assessment of exhaust gas aftertreatment systems Modal analysis (dynamic or transient analysis) during transient operations Analyzer for CO/CO2 (HC, NO, N2o, SO2), O2, THC 200 operating hours Weight 620 Kg Year of construction 2016 Type: Mexa 7100D Condition: used Pick-up from location Scope of delivery: (See picture) (Changes and errors in the technical data, information reserved!) We are happy to answer any further questions you may have on the phone.

for classic Schiesser occupancy for direct stove occupancy table oven made of stainless steel mass: 320 x 630 x 100 mm (with swivel lever 320 x740 x 100 mm) WxDxH; available immediately!

New galvanized or painted construction supports 3m, 3.50m, 4.00m at great conditions directly from the factory. From.21,50€/ Piece+ VAT Construction support painted 1,60m – 2,90m = 21,50€/piece reinforced version 2,00m - 3,50m = 23,50€/ piece reinforced version 2,30m – 4,00m = 26,50€/ piece reinforced version Construction support galvanized 1,60m - 2,90m = 25,90€/ piece reinforced version 2,00m - 3,50m = 26,90€/ piece reinforced version 2,10m – 4,00m = 29,90€/ piece reinforced version 1 frame for construction supports new, painted 70,00€ New inclined supports, painted 1,70m - 3,00m = 29,50€/ piece Inclined supports new, painted 2.10m - 3.50m. = 35,50€/ Piece Inclined supports new, painted 2,40m - 4,10m. = 38,50€/ Piece New inclined supports, galvanized 1,70m - 3,00m = 38,90€/ piece New inclined supports, galvaniz ...

Make and Model: GE WHG-125 Year: 2011 Hours: 6000 approx. Year : 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: These units have been decommissioned and been in storage since May 2016. Unit 1 and 2 had a report of an MBC fault (magnetic bearing controller). Unit 3 has several parts missing due to a failure in the power electronics. Some parts of the Power electronics, PLC, speed drive for the refrigerant pump are missing. Unit 4 had a failed heat exchanger and filled the ORC with water, would need stripping to determine the full extent of the repairs needed. Extra: These units run on a working fluid (refri ...

FOR SALE ...COMPLETE T/C NAPIER NA 457 AT TURKEY; HAVE A GDY SIR WE VE COMPLETE T/C NAPIER NA 457 AT STOCK. PLS FIND SPEC AT BELOW NA 457 701276 4FM157F 225 FJ 19500 650C. IF YOU HAVE ANY QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Kind Regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Key data: 117

Make and Model: GE WHG-125 Year: 2011 Hours : 16,000 & 35,000 Capacity kW: 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: The containerised units were decommissioned towards the end of 2018. Both of the units were operational before decommissioning. Unit 1 has the upgraded 3600 MBC (magnetic bearing controller). Both of the units are containerised at present but can be removed. Extra: These units run on a working fluid (refrigerant R245Fa) that does not come with the units as this was sent for recycling after commissioning. This will need to be purchased and filled during installation and commissioning.  ...

Linen store leaching for small quantities table table room made of stainless steel including draining plate and lid for lye tray suitable for metal size 600 x 400 mm, 530 x 650 mm, 580 x 780 mm Mass (WxDxH) in mm: 550 x 610 x 121 (with swivel lever: 550 x 710 x 121) ; ready to go!

2 x 2.9MW 60Hz NIIGATA 18V22AG Gas Power Plant for sale NIIGATA says that 18V22AG has a high electric thermal efficiency of 40% or more and the 22AG engine produced 30% higher power than a conventional spark ignition gas engine with the micro-pilot compression ignition system. Produced in 2004, this generating sets had been successfully operated about 32,000 hours and had a good condition as seen in the photos and the plant was dismantled and has been well preserved in our factory and ready for immediate delivery. Main Specifications: - Engine Model: 18V22AG x 2 sets - Maker: NIIGATA - Continuous Output: 2880kWe x 900 rpm - Frequency & Voltage: 60Hz & 6600V - Year of Production: 2004 - Running Hours: abt. 32,000 hours - Fuel Oil: Natural Gas - Plant Auxiliary Equipment: 1 set ■ Main Specifications ▣ Gas Engine Maker NIIGATA Model 18V22AG Quantity 2 sets Ye ...

VISION WIDE VB-2016 5-AXIS CNC gantry milling machine was manufactured in 2013 in Taiwan. The machine performs precision machining of heavy workpieces in three or even five axes, once the automatic swivel head is mounted to the vertical spindle. The machine’s top-quality cast-iron structure is rigid and resistant to bending stress, thus perfectly dampening the vibrations and oscillations generated during machining. The VISION WIDE VTEC VB 2016 CNC gantry milling machine centre is equipped with safety guards fitted around the entire machine with sliding doors that open flush with the X-axis travel. Inside, there is a large work table with a length of 2000 mm and a width of 1300 mm, which is supported along the entire length of the longitudinal travel and guided by two sliding guideways, making it possible to machine heavy workpieces even when the table is unevenly loaded. Two scre ...

Linen diving with salt-mounted and lye drain valve, 4-spring stand-boiler made of stainless steel incl. driving table with shelf and locking rollers suitable for tin size 580 x 780 mm, 4- or 5-row division mass in mm: 700 x 902 x 880 WxTxH; ready to go!

Built in 1997 Product thickness max 85 mm Speed max 12.000 c/h Equipment o 18 stations ; working condition

750513 + 570520

Gas forklift Yale Type: GLP-030AUA V Serial No.: Y382072 Year of construction: 1982 Weight: 2,780 kg Capacity: 1,500 kg Battery voltage: 12 V Forklift truck is fully functional and is protected with us in the Hall. Can be visited at any time! In very good condition!

5,000 litre storage containers According to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. The tank has two saddle feet, a manhole DN 500 with domed lid, is used, inside empty and professionally cleaned and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube,. 1 sounding pipe provided with dip stick and sounding Rod seal, 1 vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fluid. The container is outside new primed and painted. L = 2.80 m / D = 1.60 m / weight CA. 1.3 tons. / free charged ex works. Description PTO pump: Non calibratable type eco-box-55- Capacity up to approx. 55 l / min. suitable for diesel fuel, incl. -Automated fuel dispenser with PC softwa ...

Electric pumping system for oil or diesel for controlled extraction of oil quantities from large containers such as oil barrels, tanks, etc. Consisting of electric motor with pump, pressure monitor, hose reel, pump gun with manual pass counter with rigid outlet. Display of the extracted quantity in litres Electric pump for fresh oil supply, suitable for barrel removal or as a tank pump, Closed hose reel for oil, hose length xxm xx" hose, with wall mount and pump gun. Special price

EWD HDN/SV with width adjustment TOP ZUSTAND ! (1982/2009) WATER-CLOSED FUEHRS, SIDE BRETTERKAPPSAEGE... Through width 735 Passage shoe710 Hub 600 Speed max. 300 Feed speed 0-15 m/min Feed capacity 8.5 m/min Total weight 12 t SPALTKEIL ARTA C WITH SIDE WAREKAPPSAeGE Very well maintained facility little cut ! HDN-SV STATUS: VERY GOOD

Key data: 1400 KW, 1800 kVA, 400 V

MWM Power Generator TBG620-V16K Gas generator set from 2001, Scope of delivery: base frame and generator, as shown. Engine turns, intercooler, turbocharger, starter, ignition coils, spark plugs are missing. 1 available 1,365 KWel x 1,500 rpm, 400 V/50 Hz. AC generator: Stamford HC I734G2 CG, 1,800 KVA Gas engine MWM TBG620-V16K Manufacturer: MWM Model No.: TBG620-V16K Type: Gas generator set Serial Number: 2203129 Power [KW]: 1.400 Year of construction: 2001 Hours:– Weight [kg]: 8.588 Dimensions LxWxH [cm]: 470×145 AC generator Stamford HC I734G2 CG Manafacture: Stamford Model: HC I734G2 CG Type: AC Synchronous Generator Serial Number: 00366141 Power [KVA]: 1,800 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 2.598 Speed [1/min]: 1,500 Year of construction: 2001 Weight [kg]: 3.700

Key data: 1400 V, 1800 , 400

MWM Power Generator TBG620-V16K Gas generator set from 2001, Scope of delivery: base frame and generator, as shown. Without turbocharger, gas mixer, oil cooler and intercooler. Camshaft has signs of wear on the B side. 1 available 1,365 KWel x 1,500 rpm, 400 V/50 Hz. AC generator: Stamford HC I734G2 CG, 1,800 KVA Gas engine MWM TBG620-V16K Manufacturer: MWM Model No.: TBG620-V16K Type: Gas generator set Serial Number: 2203156 Power [KW]: 1.400 Year of construction: 2001 Hours:– Weight [kg]: 8.588 Dimensions LxWxH [cm]: 470×145 AC generator Stamford HC I734G2 CG Manafacture: Stamford Model: HC I734G2 CG Type: AC Synchronous Generator Serial Number: 0140886/06 Power [KVA]: 1,800 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 2.598 Speed [1/min]: 1,500 Year of construction: 2001 Weight [kg]: 3.700

Key data: 1400 KW, 1800 kVA, 400 V

Gas generator set from 2004, Scope of delivery: Base frame and generator, as shown with missing parts – bushings defective. 1 available 1,800 KWel x 1,500 rpm, 400 V/50 Hz. AC generator: Stamford HC I734G2 CG, 1,800 KVA Gas engine MWM TBG620-V16K Manufacturer: MWM Model No.: TBG620-V16K Type: Gas generator set Serial Number: 2205063 Power [KW]: 1.400 Year of construction: 2004 Hours:– Weight [kg]: 8.588 Dimensions LxWxH [cm]: 470×145 AC generator Stamford HC I734G2 CG Manafacture: Stamford Model: HC I734G2 CG Type: AC Synchronous Generator Serial Number: 0166189/02 Power [KVA]: 1,800 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 2.598 Speed [1/min]: 1,500 Year of construction: 2004 Weight [kg]: 3.700

For sale a motor block of 442 KW Deutz TBG604BV8 gas CHP generator. The crank shaft we can offer also. FCA Free charged on your truck.

ECKERT AGAT SPEED gas cutting machine was manufactured in Poland in 2014. The machine designed for precision cutting of metal sheets with a maximum thickness of 100 mm is distinguished by a high-quality portal with an open structure, ensuring excellent stability during the performed cutting process and free access of the operator to the working space. The contamination generated during the cutting process is continuously removed by a sectional extraction table covering the entire working area of the machine. The ECKERT gas cutting machine is also equipped with, among others, a state-of-the-art CNC ECS 872 controller and an oxygen torch support with capacitive distance sensor. Technical data of the ECKERT AGAT SPEED CNC cutting machine - CNC control: ECS 872 - maximum workpiece thickness: 100 mm - work table surface (L x W): 3000 x 2000 mm - oxygen torch support with capacitive dis ...

Key data: 3240 KW, 3294 kVA, 10500 V

Electricity and heat generator from 1998 with 61,000 operating hours, BSService at 50,000, then another 10,000 operating hours, complete (still installed). 1 available 2,635 kWel x 1,000 rpm, 10,500 V/ 50 Hz. AC generator: ABB AMG 630 L6, 3,294 kVA CHP Wärtsilä W16V25SG Manafacture: Wärtsilä Model: W16V25SG Type: Gas-fired CHP Serial Number: 4008 Mechanical power [kW]: 3.140 Thermal power [kW]: 4.272 Power fired [kW]: 8.134 Exhaust gas temperature [°C] 420 AC generator ABB AMG 630 L6 Manafacture: ABB Model: AMG 630 L6 Type: AC Synchronous Generator Serial Number: 106824 Power [kVA]: 3300 Voltage [V]: 10.500 Frequency [Hz]: 50 Current [A]: 181 Speed [1/min]: 1,000 Year of construction: 1998 Weight [kg]: 10.970

Line boring machine Ayen with 32 mm grid Bahvy3bjt2 with attacks Pneum.. Holders Motor 0.55 kW L x W x H: 250 x 80 x 200 cm Weight 420 kg Year of construction 1983 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

MWM TCG 2020 V 16 Remanufactured Motor / Short Block It is a refurbished short block. Repaired in accordance with the manufacturer's guidelines and the RAL seal of approval. Circumference: - Crankcase incl. new bearing - Crankshaft (Std-dimension) incl. new bearings - Camshafts incl. new bearings - Wheel drive incl. wheel box cover - Flywheel housing - Oil pump with oil suction pipe -Sump - Valve plunger - Oil pressure valve On request, the scope can be expanded (e.g. pistons, liners, cylinder heads, oil coolers, etc.) Further information on the scope and design can be found on our homepage: buecker-essing Removal and installation as well as service for the engine and CHP unit are optionally possible. Please contact us for a written offer. We also have other remanufactured engines, as well as AT cylinder heads, turbochargers, spare parts and other ...

Just one blow of the hammer on the RU clamp is all it takes to pull the panels together and achieve a flush, correctly aligned panel joint that is resistant to tensile forces. The panels can be continuously height mismatched, i.e. without any pre-defined grid. This means that the formwork can easily be accommodated to e.g. steps, slopes and uneven ground, with no extra work.

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Setting range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Design mobile compact system Wire feed 4-roll drive Hedging 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, very good, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece glass 90 x 110 mm white 1 piece protective glass 90 x ...

Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request

MWM TCG 2020 V 20 Remanufactured Motor / Short Block It is a refurbished short block. Repaired in accordance with the manufacturer's guidelines and the RAL seal of approval. Circumference: - Crankcase incl. new bearings - Crankshaft (Std-dimension) incl. new bearings - Camshafts incl. new bearings - Wheel drive incl. wheel box cover - Flywheel housing - Oil pump with oil suction pipe -Sump - Valve tappets - Oil pressure valve On request, the scope can be expanded (e.g. pistons, liners, cylinder heads, oil coolers, etc.) Further information on the scope and design can be found on our homepage: buecker-essing Removal and installation as well as service for the engine and CHP unit are optionally possible. Please contact us for a written offer. We also have other remanufactured engines, as well as AT cylinder heads, turbochargers, spare parts and othe ...